Multiple isight problems
I'm trying to set up 5 isights as webcams using Evocam software. I've tested the following on two systems: a powerbook G4 1.3 ghz, 1.25GB RAM, using Belkin's 6 port powered extender, and a G5 DP 2.7 4GB ram, standard Firewire ports plus added Sonnett's Tango 2 firewire card with 2 firewire ports. I'm having roughly similar results on both systems but it's all sketchy failure. I can get two camera's running without any problem. Past that watch out. Adding the third camera usually brings it up with a weird lined pattern. Sometimes I can get the third camera to work but it always seems to be dumb luck.
Amazingly after hours of trial and error I had 4 camera's going at the same time on the powerbook with Belkin 6 port powered firewire extender but the camera's died after 5 hours. They just shut off. The much more powerful G5 has barely gotten the third camera to work at the same time.
Has anybody run more than two isights at a time successfully on the same computer? Are there other options for webcamera's that have the same quallity as the isights but might work better?
I'm at a loss here since my eventual goal is to have 5 high quallity webcams running at the same time and the only way I see that possible right now is to have 3 different computers with 2 isights hooked up to each - all uploading via airport.
Thanks for any help you might offer.
g5 dp 2.7ghz 4GB RAM Mac OS X (10.4.5) evocam 2.6
Hello, Christopher. Interesting problem! Sorry, but I do not use Evocam, so I cannot offer any first-hand experience.
I'm trying to set up 5 isights as webcams using Evocam software.If nobody here has experience doing what you want to do, your best bet for this application specific help would likely be from:• the EvoCam FAQs,
• EvoCam Users Forums, or
• EvoCam's E-Mail Technical Support.Evocam users and the people who sell the software can tell you more about Evocam's capabilities and limits.
Has anybody run more than two isights at a time successfully on the same computer?Not I. I have never gone beyond one iSight and one DV camcorder connected simultaneously.
Are there other options for webcamera's that have the same quallity as the isights but might work better?Other camera options explained in iSight versus DV Camcorder or other web-cam, but, unless you get answers based on user experience, only trial and error would tell you whether they would perform "better" for your purposes.
Any EvoCam users have suggestions for Christopher ... ?
Jim
Similar Messages
-
ISight problem, time for repair?
iSight suddenly stopped working. No green light. Won't work in iChat, Gmail, or Photo Booth. Message "No camera connected to this computer". I followed the advice given here. Restarted. I checked Utilities >> System Profiler >> USB and saw iSight listed (though it said "not configured yet"). I reset the PRAM, went back to System Profiler and now iSight doesn't show up at all.
Does that pretty much exhaust my efforts? Time to bring it in?
Many thanks in advance,
robRob Keys wrote:
iSight suddenly stopped working. No green light. Won't work in iChat, Gmail, or Photo Booth. Message "No camera connected to this computer". I followed the advice given here. Restarted. I checked Utilities >> System Profiler >> USB and saw iSight listed (though it said "not configured yet"). I reset the PRAM, went back to System Profiler and now iSight doesn't show up at all.
Does that pretty much exhaust my efforts? Time to bring it in?
Many thanks in advance,
rob
You've tried some good things, Rob. You may be right that it is time for service.
For any iSight problems, first try restarting the Mac. If the problems persist, try all relevant suggestions from:
http://support.apple.com/kb/HT2090
If your iSight problem still occurs in more than one app and more than one user account, the reset suggested there (PMU/SMC for your MacBook) often restores proper function of inbuilt iSight.
However, if your built-in iSight still does not work after carefully following all the suggestions in the "How to Troubleshoot iSight" article, and if iSight does not show as a USB hardware device in your Mac's System Profiler utility, yours is most likely a hardware problem. In that case, contact Apple or an Apple-Authorized Service Provider for service.
BTW - I note that your posted system info shows Mac OS X (10.4.7). If that is correct, unless you have compelling reasons for not doing so, I suggest you backup your Mac and apply the 10.4.11 Combo Update:
http://support.apple.com/kb/DL172
For more info on how to install and benefits of updating, see http://support.apple.com/kb/TA24901
I recommend you use your Mac's Disk Utility to *repair permissions* immediately before *_and again_* immediately after the update. After repairing permissions, use your Mac's > Software Update... menu command to apply any additional needed Apple software updates.
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.5); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.5)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod4touch4.2.1 -
Multiple Inheritance problem persists in Interfaces
Hi,
I tentatively made a program and found that multiple inheritance problem of C++ persists even with interfaces. Although this is definetely a special case but I want to know what is this problem known as( i know that this is perhaps known as diamond problem in C++). And is there a way out of this thing.
interface one
int i=10;
interface two
int i=20;
interface z extends one,two
public class xyz implements z
public static void main(String [] a)
System.out.println(i);
}O/P
D:\Education\Java\JavaStudyRoom\Applets>javac xyz.java
xyz.java:16: reference to i is ambiguous, both variable i in one and variable i
in two match
System.out.println(i);
*^*
*1 error*
Thanks for replyingsuvojit168 wrote:
I tentatively made a program and found that multiple inheritance problem of C++ persists even with interfaces. Although this is definetely a special case but I want to know what is this problem known as( i know that this is perhaps known as diamond problem in C++). And is there a way out of this thing. This is not the so called diamond inheritance problem. What you have here is an ordinary name clash. And as has been noted you can resolve it by qualifying which constant you're referring to, like
System.out.println(one.i);
For the diamond inheritance problem to apply both the one and the two interfaces would need to inherit a common ancestor (that's how the diamond is formed). Furthermore the common anscestor would need to carry implementation which would then be inherited two ways, once via one and once via two. This is the diamond inheritance problem Java is avoiding by allowing single inheritance of implementation only.
P.S. My previous post was posted my mistake. -
SP10 - multiple approver problem with CUP
We have SP10 (patch 1) in our development system and cannot move forward to production because of a real show stopper. I have currently reported this to SAP thru an OSS message (and it is in development) but would like to know if anyone else is having this issue with SP10. (this happened even before applying patch 1)
We have multiple approvers when creating NEW users or CHANGING users in CUP. We have it configured to allow just one of the approvers to approve before going on to the next stage. Since we put in SP10, CUP is requiring ALL approvers to approve the request before going on to the next stage. We get the following message when one of the approvers approve the request: Request no: 5020. is approved, pending for other Approvers.
I've seen this reported for UAR and SOD but not for CUP. In fact, there is a fix for UAR in Patch 1 of SP10. I applied this patch but it hasn't fixed the CUP issue. I also don't have the issue when rejecting a CUP request, or when approving it through the configuration --> Request --> Administration screen (what I consider the Back-door since only security administrators get the configuration area).
Thanks for your input.
PeggyChristian,
I totally agree with you.
The good news is.... We installed SP11.1 and the multiple approver problem is fixed.
We have decided to leave our production system at SP8 until this system settles down a bit. Of course, this means we can't use many of the new fixes and features (such as UAR). We use our sandbox system to apply new support packs and do very rigorous testing. And our DEV system is at SP8 too.
Good Luck.
Peggy -
L430 multiple driver problems (ultranav and others)
Hello,
I have multiple driver problems with my newly purchased L430.
1) After hibernate the UltraNav driver randomly stops working. This means that the settings are grayed out and my old settings aren't applied. Sometimes the mouse pad and track ball also stop working after hibernate.
2) The hardware mute button and hibernate don't like each other as well. After resuming from hibernate with the mute button on the sound doesn't work anymore. Rebooting only helps if you have disabled the mute before rebooting.
3) The intel usb 3.0 driver can't be installed unless you want a lot of bluescreens.
I do have the newest drivers and BIOS (2.54).It's ok my friend, I just hope I will be able to help.
Now to the problem. The thing that worries me the most and the reason I asked you to contact a Lenovo Repair Center, is the blue screens with the Intel Usb 3.0 installation. If the driver is correct this should not happen and most of the times it signifies a pure hardware problem, not a software one. Really, it just should not happen, period!
So please, before anything else, download and boot with a Linux Live cd, any distro you like (e.g. Linux Mint, Fedora, etc). Better choose a 64bit version. It's one way of determining if you're facing a hardware problem with the usb 3.0 ports.
The information you give is very useful and more or less complete, but I would like to also know the model of your SSDs, both the 2.5'' and msata.
Meanwhile, you can check either with the Linux Live cd or with Memtest86+ your ram. This does not seem to be a memory problem but it would be nice if we could exclude it from the suspects list. Many - if not most - of these problems are multifactorial and we cannot leave anything to chance..
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
This will help the rest of the Community with similar issues identify the verified solution and benefit from it. -
Outlook Sync - Multiple Calendar Problem
(I am not sure whether this belongs in this Forum or would be more appropriately directed to my Device (Curve 8900) forum or Desktop Software. Please advise or re-direct if that is the case.)
I am having a sync issue with Outlook, and it revolves around the issue of having multiple calendars on the Device, each of which is associated with an e-mail address. I understand this has been a relatively common question; however, although I admittedly may be looking in the wrong place, I have yet to come across a comprehensive solution.
I understand how to switch the "default" e-mail associated with scheduling items on the calendar, and I believe I'm correct in thinking that this is what syncs with Outlook. I've noticed that when I try switching the default, Outlook wants to delete all other appointments which are NOT associated with that device calendar.
So I guess my specific questions are:
1) Is there a way to have Outlook sync with ALL calendars on the device, i.e. not just the default? It's easy enough to make all appointments from here on out with a single account & have that be the one that syncs; however, it doesn't seem possible to do that without having Outlook want to delete all other appointments.
2) Is there a way to change the associated email/calendar for events on the Device? When I open an event, I can see which email/calendar it is but I don't know how to *change* it -- I only seem to have a choice when scheduling new events.
If either of these was an option, I think that would solve my problem -- I could either go through the device & convert everything to the default email/calendar & everything would be there upon sync, OR Outlook would just pick up everything from all calendars when I sync.
I don't understand why it's so complicated to have everything in one place!
Thanks in advance to those willing to share their wisdom & advice in this matter.
mbwI was going to post that article but you beat me to it.
I believe this is the only way to accomplish this on a BlackBerry
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution. -
MULTIPLE ITEM PROBLEM IN VL31N BDC
hI FRIENDS ,
I AM POSTING A BDC OF TRANSACTION VL31N ,ie FOR SCHEDULE AGREEMENT INBOUND DELIVERY.I CREATE A FUNCTIONAL MODULE OF THE SAME AND CALL IT FROM AN ASP PAGE,IN THAT THERE IS PO NUMBER 5500000986 WHICH HAS TWO ITEMES 62 AND 95 RESPECTIVLY OF SAME MATARIAL NUMBER R010230123041002 AND DIE NUMBER 2304P,NOW THE PROBLEM IS THIS BDC IS WORKING WHEN THERE IS ONLY ONE ITEM BUT GIVES AN ERROR "CANT CREAT INBOUND DELIVERY FOR PO NO ...' WNEN IT HAS MULTIPLE ITEM.WHAT SHOULD I DO ? I ALSO USED LOOP BUT IT ALSO DOSENT WORK AS IT WILL ADD ALL OPEN QTY OF PO 986 AND UPDATE AGAINST ITEM NO 95.
CODE IS AS FOLLOWS:.........
FUNCTION y_synie_bdcinbdly.
""Local interface:
*" IMPORTING
*" VALUE(CTU) LIKE APQI-PUTACTIVE DEFAULT 'X'
*" VALUE(MODE) LIKE APQI-PUTACTIVE DEFAULT 'N'
*" VALUE(UPDATE) LIKE APQI-PUTACTIVE DEFAULT 'L'
*" VALUE(GROUP) LIKE APQI-GROUPID OPTIONAL
*" VALUE(USER) LIKE APQI-USERID OPTIONAL
*" VALUE(KEEP) LIKE APQI-QERASE OPTIONAL
*" VALUE(HOLDDATE) LIKE APQI-STARTDATE OPTIONAL
*" VALUE(NODATA) LIKE APQI-PUTACTIVE DEFAULT '/'
*" VALUE(EXTNID) LIKE MAKT-MAKTG
*" VALUE(VENDORNO) LIKE LFA1-LIFNR
*" VALUE(PONUMBER) LIKE EKKO-EBELN
*" VALUE(ITEMNUMBER) LIKE LIPS-VGPOS
*" VALUE(MATERIAL) LIKE MAKT-MAKTG
*" VALUE(DLYQTY) LIKE LIPS-LFIMG
*" VALUE(BTCHNO) LIKE LIPS-CHARG
*" VALUE(POSLR) LIKE EKES-EBELP OPTIONAL
*" EXPORTING
*" VALUE(SUBRC) LIKE SYST-SUBRC
*" VALUE(INDELYNO) LIKE SY-MSGV2
*" VALUE(MSG1) LIKE SY-MSGV1
*" VALUE(MSG2) LIKE SY-MSGV2
*" VALUE(MSG3) LIKE SY-MSGV3
*" VALUE(MSG4) LIKE SY-MSGV4
*" TABLES
*" MESSTAB STRUCTURE BDCMSGCOLL
*" ERRTAB STRUCTURE YSYNERRMSGS
*" INDLYTAB STRUCTURE YSYN_QTYTAB
Updated by ANAND SYNISE 19.1.2007
DATA: BEGIN OF bdctab OCCURS 0.
INCLUDE STRUCTURE bdcdata.
DATA: END OF bdctab.
DATA: datenow(10) TYPE c,
fldvar(30) TYPE c,
fldno TYPE i,
flditoc(6) TYPE c,
qty(13) TYPE c.
DATA maxposnr LIKE lips-posnr.
DATA testposnr TYPE posnr.
DATA itemnoint TYPE i.
CONCATENATE sy-datum6(2) '.' sy-datum4(2) '.' sy-datum+0(4) INTO datenow.
CLEAR bdctab.
REFRESH bdctab.
PERFORM open_group USING group user keep holddate ctu.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '4007'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'RV50A-VERUR_LA'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '/00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-LIFNR'.
bdctab-fval = vendorno.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LV50C-BSTNR'.
bdctab-fval = ponumber.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-VERUR_LA'.
bdctab-fval = extnid.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '1000'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '=MKAL_T'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'LIKP-BLDAT'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-BLDAT'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '1000'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '=POPO_T'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-BLDAT'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'LIPS-POSNR(01)'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '0111'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'RV50A-PO_MATNR'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = 'WEIT'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-PO_MATNR'.
bdctab-fval = material.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '1000'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '=POLO_T'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-BLDAT'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'LIPS-POSNR(01)'.
APPEND bdctab.
*ADDED BY ANAND ON 22-01-2007
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = ITEMNUMBER . "ITEMNUMBER = LIPS-VGPOS
APPEND bdctab.
************ENDED***********************
ADDED BY MILIND 19.01.2007
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = poslr .
APPEND bdctab.
* ENDED * *
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LIPS_SELKZ(01)'.
bdctab-fval = ''.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '1000'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '/00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-BLDAT'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'LIPS-CHARG(01)'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
QTY = INDLYTAB-DLYQTY.
qty = dlyqty.
bdctab-fnam = 'LIPSD-G_LFIMG(01)'.
bdctab-fval = QTY.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIPS-CHARG(01)'.
* BDCTAB-FVAL = INDLYTAB-BTCHNO.
bdctab-fval = btchno.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-program = 'SAPMV50A'.
bdctab-dynpro = '1000'.
bdctab-dynbegin = 'X'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_OKCODE'.
bdctab-fval = '=SICH_T'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'LIKP-BLDAT'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_CURSOR'.
bdctab-fval = 'LIPS-MATNR(02)'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFDAT_LA'.
bdctab-fval = datenow.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'RV50A-LFUHR_LA'.
bdctab-fval = '00:00'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CLEAR bdctab.
bdctab-fnam = 'BDC_SUBSCR'.
bdctab-fval = 'SAPMV50A'.
APPEND bdctab.
CALL TRANSACTION 'VL31N' USING bdctab MODE 'N' MESSAGES INTO messtab.
subrc = sy-subrc.
PERFORM close_group USING ctu.
CLEAR bdctab.
REFRESH bdctab.
IF sy-subrc EQ 0.
indelyno = sy-msgv2.
ENDIF.
LOOP AT messtab.
MOVE: messtab-msgid TO errtab-msgid,
messtab-msgnr TO errtab-msgnr,
messtab-msgv1 TO errtab-msg1,
messtab-msgv2 TO errtab-msg2,
messtab-msgv3 TO errtab-msg3,
messtab-msgv4 TO errtab-msg4.
APPEND ERRtab.
ENDLOOP.
LOOP AT errtab.
SELECT SINGLE text FROM t100
INTO errtab-errmsg
WHERE msgnr EQ errtab-msgnr AND arbgb EQ errtab-msgid
AND sprsl EQ sy-langu.
MODIFY errtab.
ENDLOOP.
ENDFUNCTION.Hi,
Check this code:
REPORT Z_CUSTOMER_UPLOAD .
D A T A D E C L A R A T I O N S *
DATA:BEGIN OF IT_CUSTOMER OCCURS 0,
KUNNR LIKE MV10A-KUNNR,
VKORG LIKE MV10A-VKORG,
VTWEG LIKE MV10A-VTWEG,
MATNR LIKE MV10A-MATNR,
KDMAT LIKE MV10A-KDMAT,
MEGRU LIKE MV10A-MEGRU,
SELKZ TYPE C value 'X',
LPRIO LIKE MV10A-LPRIO,
ANTLF LIKE MV10A-ANTLF,
END OF IT_CUSTOMER.
DATA:BEGIN OF IT_success OCCURS 0,
KUNNR LIKE MV10A-KUNNR,
VKORG LIKE MV10A-VKORG,
VTWEG LIKE MV10A-VTWEG,
MATNR LIKE MV10A-MATNR,
KDMAT LIKE MV10A-KDMAT,
MEGRU LIKE MV10A-MEGRU,
SELKZ TYPE C value 'X',
LPRIO LIKE MV10A-LPRIO,
ANTLF LIKE MV10A-ANTLF,
END OF IT_success.
DATA:BEGIN OF IT_error OCCURS 0,
KUNNR LIKE MV10A-KUNNR,
VKORG LIKE MV10A-VKORG,
VTWEG LIKE MV10A-VTWEG,
MATNR LIKE MV10A-MATNR,
KDMAT LIKE MV10A-KDMAT,
MEGRU LIKE MV10A-MEGRU,
SELKZ TYPE C value 'X',
LPRIO LIKE MV10A-LPRIO,
ANTLF LIKE MV10A-ANTLF,
END OF IT_error.
DATA: L_INDEX TYPE SY-TABIX.
DATA:IT_BDC LIKE BDCDATA OCCURS 0 WITH HEADER LINE,
IT_DATA TYPE ALSMEX_TABLINE OCCURS 0 WITH HEADER LINE.
ERROR MESSAGE TABLE
DATA:IT_MESSAGES LIKE BDCMSGCOLL OCCURS 0 WITH HEADER LINE.
DATA : C_S TYPE C VALUE 'S',
C_E TYPE C VALUE 'E'.
*DATA: IT_SUCCESS LIKE IT_CUSTOMER OCCURS 0,
IT_ERROR LIKE IT_CUSTOMER OCCURS 0.
DATA : V_RECTOT TYPE I,
V_RECERR TYPE I,
V_RECSUC TYPE I.
S E L E C T I O N - S C R E E N *
SELECTION-SCREEN : BEGIN OF BLOCK B1 WITH FRAME TITLE TEXT-001.
PARAMETER : P_FILE LIKE RLGRAP-FILENAME .
SELECTION-SCREEN : END OF BLOCK B1.
A T S E L E C T I O N - S C R E E N *
AT SELECTION-SCREEN ON VALUE-REQUEST FOR P_FILE.
to get F4 help for p_file
PERFORM F4_FILENAME USING P_FILE.
S T A R T O F S E L E C T I O N *
START-OF-SELECTION.
Uploading data from flat file into it_tab
PERFORM BDC_UPLOAD USING P_FILE.
PERFORM PROCESS_DATA.
PERFORM POPULATE_BDC.
E N D O F S E L E C T I O N *
*END-OF-SELECTION.
PERFORM DISPLAY_REPORT.
*& Form F4_FILENAME
text
-->P_P_FILE text
FORM F4_FILENAME USING P_P_FILE.
DATA:L_FILE TYPE IBIPPARMS-PATH.
CALL FUNCTION 'F4_FILENAME'
EXPORTING
PROGRAM_NAME = SYST-CPROG
DYNPRO_NUMBER = SYST-DYNNR
FIELD_NAME = ' '
IMPORTING
FILE_NAME = L_FILE .
P_P_FILE = L_FILE.
ENDFORM. " F4_FILENAME
*& Form BDC_UPLOAD
text
-->P_P_FILE text
FORM BDC_UPLOAD USING P_P_FILE.
CALL FUNCTION 'ALSM_EXCEL_TO_INTERNAL_TABLE'
EXPORTING
FILENAME = P_P_FILE
I_BEGIN_COL = 1
I_BEGIN_ROW = 1
I_END_COL = 8
I_END_ROW = 1000
TABLES
INTERN = IT_DATA
EXCEPTIONS
INCONSISTENT_PARAMETERS = 1
UPLOAD_OLE = 2
OTHERS = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDFORM. " BDC_UPLOAD
*& Form PROCESS_DATA
text
--> p1 text
<-- p2 text
FORM PROCESS_DATA.
SORT IT_DATA BY ROW COL.
LOOP AT IT_DATA.
CASE IT_DATA-COL.
WHEN 1.
IT_CUSTOMER-KUNNR = IT_DATA-VALUE.
WHEN 2.
IT_CUSTOMER-VKORG = IT_DATA-VALUE.
WHEN 3.
IT_CUSTOMER-VTWEG = IT_DATA-VALUE.
WHEN 4.
IT_CUSTOMER-MATNR = IT_DATA-VALUE.
WHEN 5.
IT_CUSTOMER-KDMAT = IT_DATA-VALUE.
WHEN 6.
IT_CUSTOMER-MEGRU = IT_DATA-VALUE.
WHEN 7.
IT_CUSTOMER-LPRIO = IT_DATA-VALUE.
WHEN 8.
IT_CUSTOMER-ANTLF = IT_DATA-VALUE.
APPEND IT_CUSTOMER.
ENDCASE.
ENDLOOP.
ENDFORM. " PROCESS_DATA
*& Form POPULATE_BDC
text
--> p1 text
<-- p2 text
FORM POPULATE_BDC.
DATA:L_COUNTER TYPE N,
L_STRING TYPE STRING.
LOOP AT IT_CUSTOMER.
AT NEW KUNNR.
CLEAR L_COUNTER.
L_INDEX = SY-TABIX.
READ TABLE IT_CUSTOMER INDEX L_INDEX.
perform bdc_dynpro using 'SAPMV10A' '0100'.
perform bdc_field using 'MV10A-KUNNR'
IT_CUSTOMER-KUNNR.
perform bdc_field using 'MV10A-VKORG'
IT_CUSTOMER-VKORG.
perform bdc_field using 'MV10A-VTWEG'
IT_CUSTOMER-VTWEG.
perform bdc_field using 'BDC_OKCODE'
'/00'.
ENDAT.
L_COUNTER = L_COUNTER + 1.
CLEAR L_STRING.
perform bdc_dynpro using 'SAPMV10A' '0200'.
CONCATENATE 'MV10A-MATNR(' L_COUNTER ')' INTO L_STRING.
perform bdc_field using L_STRING
IT_CUSTOMER-MATNR.
CONCATENATE 'MV10A-KDMAT(' L_COUNTER ')' INTO L_STRING.
perform bdc_field using L_STRING
IT_CUSTOMER-KDMAT.
CONCATENATE 'MV10A-MEGRU(' L_COUNTER ')' INTO L_STRING.
perform bdc_field using L_STRING
IT_CUSTOMER-MEGRU.
perform bdc_field using 'BDC_OKCODE'
'/00'.
*-- For Page down in Call Transaction Mode
IF L_COUNTER = 14.
CLEAR L_COUNTER.
PERFORM BDC_DYNPRO USING 'SAPMV45A' '4001'.
PERFORM BDC_FIELD USING 'BDC_OKCODE'
'=P+'.
ENDIF.
perform bdc_dynpro using 'SAPMV10A' '0200'.
CONCATENATE 'MV10A-SELKZ(' L_COUNTER ')' INTO L_STRING.
perform bdc_field using L_STRING
IT_CUSTOMER-SELKZ.
perform bdc_field using 'BDC_OKCODE'
'=SELE'.
perform bdc_dynpro using 'SAPMV10A' '0300'.
perform bdc_field using 'MV10A-KDMAT'
IT_CUSTOMER-KDMAT.
perform bdc_field using 'MV10A-LPRIO'
IT_CUSTOMER-LPRIO.
perform bdc_field using 'MV10A-ANTLF'
IT_CUSTOMER-ANTLF.
PERFORM BDC_FIELD USING 'BDC_OKCODE'
'/EBACK'.
at end of kunnr.
READ TABLE IT_CUSTOMER INDEX L_INDEX.
perform bdc_field using 'BDC_OKCODE'
'=SICH'.
CALL TRANSACTION 'VD51' USING IT_BDC MODE 'A' UPDATE 'S'
MESSAGES INTO IT_MESSAGES.
CLEAR IT_BDC.
REFRESH IT_BDC.
ENDAT.
IF NOT IT_MESSAGES[] IS INITIAL.
PERFORM FORMAT_MESSAGE.
ENDIF.
ENDLOOP.
ENDFORM. " POPULATE_BDC
*& Form bdc_dynpro
text
-->P_0273 text
-->P_0274 text
FORM bdc_dynpro USING VALUE(P_0273)
VALUE(P_0274).
IT_BDC-PROGRAM = P_0273.
IT_BDC-DYNPRO = P_0274.
IT_BDC-DYNBEGIN = 'X'.
APPEND IT_BDC.
CLEAR IT_BDC.
ENDFORM. " bdc_dynpro
*& Form bdc_field
text
-->P_0278 text
-->P_RECORD_KUNNR_001 text
FORM bdc_field USING VALUE(P_0278)
VALUE(P_0279).
IT_BDC-FNAM = P_0278.
IT_BDC-FVAL = P_0279.
APPEND IT_BDC.
CLEAR IT_BDC.
ENDFORM. " bdc_field
*& Form FORMAT_MESSAGE
text
--> p1 text
<-- p2 text
FORM FORMAT_MESSAGE.
DATA: L_MSG(100).
LOOP AT IT_MESSAGES.
READ TABLE IT_CUSTOMER INDEX L_INDEX.
CALL FUNCTION 'FORMAT_MESSAGE'
EXPORTING
ID = IT_MESSAGES-MSGID
LANG = SY-LANGU
NO = IT_MESSAGES-MSGNR
V1 = IT_MESSAGES-MSGV1
V2 = IT_MESSAGES-MSGV2
V3 = IT_MESSAGES-MSGV3
V4 = IT_MESSAGES-MSGV4
IMPORTING
MSG = L_MSG
EXCEPTIONS
NOT_FOUND = 1
OTHERS = 2.
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
write:/ l_msg.
ENDLOOP.
ENDFORM. " FORMAT_MESSAGE
reward if helpful,
keerthi -
there is an example in oracle warehouse builder user's guide how to load xml file into multiple tables (1:N relationship).
Let's have an xml file:
<orders>
<order>
<id>1</id>
<items>
<item>
<product>a</product>
</item>
</items>
</order>
</orders>
but what if one day you get an xml file where an order has no items:
<orders>
<order>
<id>10</id>
</order>
</orders>
I get an error message: ORA-20011: Error occurred while loading source XML document into the target database object XXX . Base exception: No rows to modify -- the row enclosing tag missing. Specify the correct row enclosing tag.
What I want is to load in order table one row, and no rows in items table.
The xsl for this small example that makes a problem looks like (the rest is like in oracle warehouse builder user's guide example in C appendix):
<?xml version = '1.0' encoding = 'UTF-8'?>
<xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform">
<xsl:template match="/">
<ROWSET>
<xsl:for-each select="orders/order/items/item">
<ROW>
<ORDER_ID>
<xsl:value-of select="../../id"/>
</ORDER_ID>
<PRODUCT>
<xsl:value-of select="product"/>
</PRODUCT>
</ROW>
</xsl:for-each>
</ROWSET>
</xsl:template>
</xsl:stylesheet>Sounds like you've missed some tag from the files.
For XML processing I would look at leveraging XDB, see the post here;
http://blogs.oracle.com/warehousebuilder/2007/09/leveraging_xdb.html
Cheers
David -
Details? I posted a question about one problem (for which no answers have been offered, but that's okay) and somehow, I've become part of multiple threads about various firefox problems. I have no interest in any of these questions/problems.
How do I get out of these threads? I get about 15-20 emails a day! Firefox is by far the worst community I've even been dragged into....Sorry you are having problems.
Have a look at your settings in the dropdown from the username or https://support.mozilla.org/en-US/users/settings
Not too sure what you could subscribe to accidentally that causes that behaviour though.
It would be interesting to know what option caused all the email. If something has gone wrong and you are getting e-mails that you should not be getting we can refer this to the admins to look into. The Firefox sumo community certainly does not intentionally spam, and if you are having a problem lets find out more, because others may have a problem and not have reported it. -
Data template multiple selection problem
Hi all,
I have a problem with the Multiple Selection on the BI Publisher using data templates. One of my parameters is called p_application, this parameter is a integer/number and its values come from a list of values.
I'm getting the error "....invalid number". I think the data template is not understanding that this parameter have multiple selection.
Can you help me?
here is my data template
<dataTemplate name="user_reg" dataSourceRef="Thomson_Live_ EDC_Environment">
<properties>
<property name="include_parameters" value="false"/>
<property name="include_null_Element" value="false"/>
<property name="include_rowsettag" value="false"/>
<property name="scalable_mode" value="on"/>
<property name="db_fetch_size" value="20"/>
<property name="scalable_mode" value="on"/>
</properties>
<parameters>
<parameter name="p_customer" dataType="string" include_in_output="false"/>
<parameter name="p_application" dataType="integer" include_in_output="false"/>
<parameter name="p_start_date" dataType="date" include_in_output="false"/>
<parameter name="p_final_date" dataType="date" include_in_output="false"/>
<parameter name="p_staff_account" dataType="string" include_in_output="false"/>
</parameters>
<dataQuery>
<sqlStatement name="Q1">
<![CDATA[
select COUNT(DISTINCT TRUNC(a.TIMESTAMP)) days_logged
,COUNT(a.USER_ID) logins
,max(a.TIMESTAMP) last_access
,a.application_id application_id
,a.user_id user_id
from user_history_log a,
idweb_user b,
idweb_customer c
where to_date(to_char(a.timestamp,'dd-mm-rrrr'),'dd-mm-rrrr') between to_date(:p_start_date,'dd-mm-rrrr') and to_date(:p_final_date,'dd-mm-rrrr')
and a.user_id = b.user_id
and b.customer_key = c.customer_key
and c.staff_account = :p_staff_account
and ('0' in (:p_customer) or b.customer_key in (:p_customer))
and (0 in (:p_application) or a.application_id in (:p_application))
group by a.application_id, a.user_id ]]>
</sqlStatement>
<sqlStatement name="Q2">
<![CDATA[
SELECT IDCU.CUSTOMER_NAME "Customer name"
,PCAP.APPLICATION_NAME "Application name"
,IDUS.FIRST_NAME "First name"
,IDUS.LAST_NAME "Last name"
,IDUS.USER_NAME "Username"
,IDUS.EMAIL_ADDRESS "Email address"
,IDUS.ROLE "Job Role"
,IDUS.AREA "Job Area"
,IDUS.DEPARTMENT "Specific Job Area"
,IDUS.CITY "City"
,IDUS.US_STATE "State"
,IDUS.COUNTRY "Country"
,SALE.TERRITORY_NAME "Territory/GAM"
,BUUN.BUSINESS_UNIT_NAME "SBU"
,to_char(IDUS.REGISTRATION_DATE,'dd-mm-yyyy') "Registration date"
,to_char(PCCA.EXPIRY_DATE,'dd-mm-yyyy') "Expiry date"
,DECODE(PCUA.DISABLED,'Y','Disabled','Enabled') "Status"
,pcua.application_id application_id
,pcua.user_id user_id
FROM PC_USER_APPLICATION PCUA
,PC_CUSTOMER_APPLICATION PCCA
,IDWEB_USER IDUS
,IDWEB_CUSTOMER IDCU
,sales_territory SALE
,business_unit BUUN
,PC_APPLICATION PCAP
WHERE BUUN.BUSINESS_UNIT_ID(+) = IDCU.SBU_ID
AND SALE.TERRITORY_ID(+) = IDCU.TERRITORY_ID
AND IDCU.CUSTOMER_KEY = IDUS.CUSTOMER_KEY
AND IDUS.USER_ID = PCUA.USER_ID
AND PCCA.CUSTOMER_KEY = IDCU.CUSTOMER_KEY
AND PCCA.APPLICATION_ID = PCAP.APPLICATION_ID
AND PCAP.APPLICATION_ID = PCUA.APPLICATION_ID
AND NVL(IDUS.DISABLED,'N') = 'N'
AND IDCU.STAFF_ACCOUNT = :p_staff_account
AND ('0' in (:p_customer) or IDCU.CUSTOMER_KEY in (:p_customer))
AND (0 in (:p_application) or pcap.application_id in (:p_application))
ORDER BY IDCU.CUSTOMER_NAME, PCAP.APPLICATION_NAME, IDUS.USER_NAME ]]>
</sqlStatement>
<sqlStatement name="Q3">
<![CDATA[
select COUNT(a.TIMESTAMP) "Number of Turnaways Kickout",
MAX(a.timestamp) "Last Turnaway Kickout",
a.application_id,
a.user_id
from tpharma_user.user_refused a,
idweb_user i
where to_date(to_char(a.timestamp,'dd-mm-rrrr'),'dd-mm-rrrr') between to_date(:p_start_date,'dd-mm-rrrr') and to_date(:p_final_date,'dd-mm-rrrr')
and (0 in (:p_application) or a.application_id in (:p_application))
and a.user_id = i.user_id
and ('0' in (:p_customer) or i.customer_key in (:p_customer))
group by a.application_id, a.user_id ]]>
</sqlStatement>
<link name="ruser3" parentQuery="Q1" parentColumn="user_id" childQuery="Q3" childColumn="user_id(+)" condition="="/>
<link name="rapp3" parentQuery="Q1" parentColumn="application_id" childQuery="Q3" childColumn="application_id(+)" condition="="/>
<link name="ruser1" parentQuery="Q1" parentColumn="user_id" childQuery="Q2" childColumn="user_id" condition="="/>
<link name="rapp1" parentQuery="Q1" parentColumn="application_id" childQuery="Q2" childColumn="application_id" condition="="/>
</dataQuery>
<dataStructure>
<group name="G_totals1" source="Q1">
<element name="days_logged" value="days_logged"/>
<element name="logins" value="logins"/>
<element name="last_access" value="last_access"/>
<element name="application_id" value="application_id"/>
<element name="user_id" value="user_id"/>
</group>
<group name="G_main" source="Q2">
<element name="Customer name" value="Customer name">
<element name="Application name" value="Application name">
<element name="First name" value="First name">
<element name="Last name" value="Last name">
<element name="Username" value="Username">
<element name="Email address" value="Email address">
<element name="Job Role" value="Job Role">
<element name="Job Area" value="Job Area">
<element name="Specific Job Area" value="Specific Job Area">
<element name="City" value="City">
<element name="State" value="State">
<element name="Country" value="Country">
<element name="Territory/GAM" value="Territory/GAM">
<element name="SBU" value="SBU">
<element name="Registration date" value="Registration date">
<element name="Expiry date" value="Expiry date">
<element name="Status" value="Status">
<element name="application_id" value="application_id"/>
<element name="user_id" value="user_id"/>
</group>
<group name="G_main" source="Q3">
<element name="Number of Turnaways Kickout" value="Number of Turnaways Kickout"/>
<element name="Last Turnaway Kickout" value="Last Turnaway Kickout"/>
<element name="application_id" value="application_id"/>
<element name="user_id" value="user_id"/>
</group>
</dataStructure>
</dataTemplate>
on the XDO file, the parameters are:
<parameters>
<parameter id="p_customer" defaultValue="8c3ff6ad5eh5c8" dataType="xsd:string">
<select label="Customer: " valueSet="lv_customer" multiple="true" all="false" allValue="lov"/>
</parameter>
<parameter id="p_application" defaultValue="1" dataType="xsd:integer">
<select label="Application: " valueSet="LV_application" multiple="true" all="false" allValue="lov"/>
</parameter>
<parameter id="p_start_date" defaultValue="{$SYSDATE()$}" dataType="xsd:date">
<date label="Usage occurs on or after (dd-mm-yyyy):" size="11" format="dd-MM-yyyy" minValue="01-06-1950" maxValue="01-06-2100"/>
</parameter>
<parameter id="p_final_date" defaultValue="{$SYSDATE()$}" dataType="xsd:date">
<date label="Usage occurs on or before (dd-mm-yyyy):" size="11" format="dd-MM-yyyy" minValue="01-06-1950" maxValue="01-06-2100"/>
</parameter>
<parameter id="p_staff_account" defaultValue="Y">
<select label="Staff Accout: " valueSet="lv_staff_account" multiple="false" all="false" allValue="null"/>
</parameter>
</parameters>
Thank you,
Marcelo Cure
Oracle Developer
[email protected]
www.ilegra.com
Edited by: user11307652 on 09/03/2010 05:21
Edited by: user11307652 on 09/03/2010 06:15I have a similar problem where i cannot use the parameter with comma separated values in the parameter.
my report definition is as below.
<dataTemplate name="COMLTRDATA" description="Data for the COMLTR letters" dataSourceRef="PRISM">
<parameters>
<parameter name="secondary_sequence" dataType="number" include_in_output="false"/>
</parameters>
<dataQuery>
<sqlStatement name="Q1">
<![CDATA[select PR_LETTER_MASTER.LETTER_ID as LETTER_ID,
to_char(PR_LETTER_MASTER.LETTER_DATE,'FMMonth DD, RRRR') as LETTER_DATE,
PR_LETTER_MASTER.LETTER_NAME as LETTER_NAME,
PR_LETTER_MASTER.ADDRESS_TYPE as ADDRESS_TYPE,
PR_LETTER_MASTER.REVIEWED_FIRM_NUMBER as REVIEWED_FIRM_NUMBER,
PR_LETTER_MASTER.REVIEWED_FIRM_NAME as REVIEWED_FIRM_NAME,
PR_LETTER_MASTER.REVIEWED_FIRM_TYPE as REVIEWED_FIRM_TYPE,
PR_LETTER_MASTER.REVIEWING_FIRM_NUMBER as REVIEWING_FIRM_NUMBER,
PR_LETTER_MASTER.REVIEW_NUMBER as REVIEW_NUMBER,
PR_LETTER_MASTER.SALUTATION as SALUTATION,
PR_LETTER_MASTER.SIGNATURE_EMAIL_ID as SIGNATURE_EMAIL_ID,
PR_LETTER_MASTER.SIGNATURE_TITLE as SIGNATURE_TITLE,
PR_LETTER_MASTER.REVIEW_STATUS as REVIEW_STATUS,
to_char(PR_LETTER_MASTER.REVIEW_COMMENCEMENT_DATE,'FMMonth DD, RRRR') as REVIEW_COMMENCEMENT_DATE,
to_char(PR_LETTER_MASTER.REVIEW_DUE_DATE,'FMMonth DD, RRRR') as REVIEW_DUE_DATE,
PR_LETTER_MASTER.REVIEW_YEAR as REVIEW_YEAR,
PR_LETTER_MASTER.REVIEW_PROGRAM as REVIEW_PROGRAM,
PR_LETTER_MASTER.REVIEW_TYPE as REVIEW_TYPE,
PR_LETTER_MASTER.TEAM_CAPT_FIRM_NAME as TEAM_CAPT_FIRM_NAME,
PR_LETTER_MASTER.PRIOR_REVIEW_NUMBER as PRIOR_REVIEW_NUMBER,
PR_LETTER_MASTER.MNGPTR_MEMBER_NUMBER as MNGPTR_MEMBER_NUMBER,
PR_LETTER_MASTER.FIRST_NAME as FIRST_NAME,
PR_LETTER_MASTER.MIDDLE_INITIAL as MIDDLE_INITIAL,
PR_LETTER_MASTER.LAST_NAME as LAST_NAME,
PR_LETTER_MASTER.ADDRESS_LINE1 as ADDRESS_LINE1,
PR_LETTER_MASTER.ADDRESS_LINE2 as ADDRESS_LINE2,
PR_LETTER_MASTER.ADDRESS_LINE3 as ADDRESS_LINE3,
PR_LETTER_MASTER.CITY as CITY,
PR_LETTER_MASTER.STATE as STATE,
PR_LETTER_MASTER.ZIP as ZIP,
PR_LETTER_MASTER.ZIP_PLUS as ZIP_PLUS,
PR_LETTER_MASTER.DELIVERY_EMAIL_ID as DELIVERY_EMAIL_ID,
PR_LETTER_MASTER.SIGNATURE_TYPE as SIGNATURE_TYPE,
PR_LETTER_MASTER.SIGNATURE_NAME as SIGNATURE_NAME,
PR_LETTER_MASTER.TEAM_CAPT_MEMBER_NUMBER as TEAM_CAPT_MEMBER_NUMBER,
PR_LETTER_MASTER.SIGNATURE_PHONE_NUMBER as SIGNATURE_PHONE_NUMBER,
PR_LETTER_MASTER.LAST_LETTER_SENT_DATE1 as LAST_LETTER_SENT_DATE1,
PR_LETTER_MASTER.LAST_LETTER_SENT_DATE2 as LAST_LETTER_SENT_DATE2,
PR_LETTER_MASTER.LAST_LETTER_SENT_DATE3 as LAST_LETTER_SENT_DATE3,
to_char(PR_LETTER_MASTER.EXIT_CONFERENCE_DATE,'FMMonth DD, RRRR') as EXIT_CONFERENCE_DATE,
PR_LETTER_MASTER.REVIEW_TAX_SEASON as REVIEW_TAX_SEASON,
PR_LETTER_MASTER.STATE_SOCIETY_NUM as STATE_SOCIETY_NUM,
PR_LETTER_MASTER.STATE_SOCIETY_NAME as STATE_SOCIETY_NAME,
PR_LETTER_MASTER.SECONDARY_LETTER_SEQUENCE as SECONDARY_LETTER_SEQUENCE,
PR_LETTER_MASTER.CREATION_DATE as CREATION_DATE,
PR_LETTER_MASTER.STATE_CODE as STATE_CODE ,
PR_LETTER_MASTER.DELIVERY_EMAIL_ID as DELIVERY_EMAIL_ID,
PR_LETTER_MASTER.TEAM_CAPT_FIRST_NAME as TEAM_CAPT_FIRST_NAME,
PR_LETTER_MASTER.TEAM_CAPT_LAST_NAME as TEAM_CAPT_LAST_NAME,
to_char(PR_LETTER_MASTER.DT_RAB_PRESENTATION,'FMMonth DD, RRRR') as DT_RAB_PRESENTATION,
PR_LETTER_MASTER.RAB_DESCRIPTION as RAB_DESCRIPTION ,
PR_LETTER_MASTER.TEAM_CAPT_MIDDLE_INITIAL as TEAM_CAPT_MIDDLE_INITIAL,
pr_letter_master.salutation as Salutation
from PRISM.PR_LETTER_MASTER PR_LETTER_MASTER
where secondary_letter_sequence in (:secondary_sequence)]]>
</sqlStatement>
<sqlStatement name="Q2">
<![CDATA[select followup_description from pr_letter_details where secondary_letter_sequence = :SECONDARY_LETTER_SEQUENCE]]>
</sqlStatement>
</dataQuery>
<dataStructure>
<group name="letter1" source="Q1">
<element name="LETTER_DATE" value="LETTER_DATE"/>
<element name="FIRST_NAME" value="FIRST_NAME"/>
<element name="MIDDLE_INITIAL" value="MIDDLE_INITIAL"/>
<element name="LAST_NAME" value="LAST_NAME"/>
<element name="ADDRESS_LINE1" value="ADDRESS_LINE1"/>
<element name="ADDRESS_LINE2" value="ADDRESS_LINE2"/>
<element name="ADDRESS_LINE3" value="ADDRESS_LINE3"/>
<element name="CITY" value="CITY"/>
<element name="STATE" value="STATE"/>
<element name="ZIP" value="ZIP"/>
<element name="ZIP_PLUS" value="ZIP_PLUS"/>
<element name="SALUTATION" value="SALUTATION"/>
<element name="REVIEW_TYPE" value="REVIEW_TYPE"/>
<element name="DT_RAB_PRESENTATION" value="DT_RAB_PRESENTATION"/>
<element name="RAB_DESCRIPTION" value="RAB_DESCRIPTION"/>
<element name="SIGNATURE_NAME" value="SIGNATURE_NAME"/>
<element name="SIGNATURE_PHONE_NUMBER" value="SIGNATURE_PHONE_NUMBER"/>
<element name="SIGNATURE_TITLE" value="SIGNATURE_TITLE"/>
<element name="SIGNATURE_EMAIL_ID" value="SIGNATURE_EMAIL_ID"/>
<element name="TEAM_CAPT_MIDDLE_INITIAL" value="TEAM_CAPT_MIDDLE_INITIAL"/>
<element name="TEAM_CAPT_FIRST_NAME" value="TEAM_CAPT_FIRST_NAME"/>
<element name="TEAM_CAPT_LAST_NAME" value="TEAM_CAPT_LAST_NAME"/>
<element name="REVIEWED_FIRM_NUMBER" value="REVIEWED_FIRM_NUMBER"/>
<element name="REVIEWED_FIRM_NAME" value="REVIEWED_FIRM_NAME"/>
<element name="REVIEW_NUMBER" value="REVIEW_NUMBER"/>
<element name="LETTER_ID" value="LETTER_ID"/>
<group name="Detail" source="Q2">
<element name="followup_description" value="followup_description"/>
</group>
</group>
</dataStructure>
</dataTemplate> -
RE: HR ABAP Multiple selection problem on input selection-screen
hi friends,
I AM Facing one problem in HR abap report selection-screen , in my report employee details data getting based on payroll area
of selection-screen. Here iam SELECTION-SCREEN declarations made in program level NOT created REPORT CATEGORY FOR
PNP LDB.
ACTUAL MY PROBLEM IS IF I SELECT SINGLE PAYROLL AREA IN SELECTION-SCREEN IT GETTING DATA PERFECTLY FOR THAT
PAYROLL AREA
EX. ZA - PAYROLL AREA IF I SELECT IN SELECTION SCREEN IT FETCHING THAT PAYROLL AREA DATA PERFECTLY, PROBLEM
IS IF I SELECT MULTIPLE PAYROLL AREAS IN SELECTION-SCREEN PAYROLL AREA FIELD ZA AND ZB PAYROLLS IT FETCHING
ONLY ZA -PAYROLL DATA ONLY IT IS NOT FETCHING DATA FROM ZB PAYROLL AREA.MY REQUIREMENT IS IT SHOULD FETCH
BOTH PAYROLL DATA AND SHOWING .
HERE IAM GIVING MY SELECTION SCREEN DECLARATION SYNTAX.
SELECTION-SCREEN BEGIN OF BLOCK B2 WITH FRAME TITLE TEXT-001.
SELECT-OPTIONS:
S_ABKRS FOR P0001-ABKRS NO INTERVALS," NO-EXTENSION, " PAY ROLL AREA
S_PERSA FOR P0001-WERKS NO INTERVALS," NO-EXTENSION, " PERS.AREA
SELECTION-SCREEN END OF BLOCK B2 .
PLEASE Any body knows solution for this selection give me reply.
regards,
gopalIf you are using Logical DB PNP why are you coding Selection Fields for ABKRS and WERKS? Both of these fields are defined in the PNP Selection Screen and if you use those fields then SAP will handle filtering the data.
-
Erratic iSight problem on MacBook Pro
The iSight camera on my MacBook Pro 17" comes and goes constantly. It vanishes from System Profiler at times too. I've rest the NVRAM and logged in as other users too. Its like it has a mind of its own. Turning on the green LED and off, then refusing to let other programs like iChat or Photo Booth from connecting, sometimes saying the camera is in use even. Its very fustrating also since I use the camera sometimes in iChat or Skype only to have the image lockup. The camera vanishes. I'm not sure if its a hardware problem or a kernel problem.
I've decided to try to monitor its failure with the HardwareGrowler.app. The camera randomly connects and disconnects. Growl notification show:
USB Disconnection
Built-in iSight
USB Disconnection
IOUSBVendorSpecifiDevice
USB Connection
IOUSBVendorSpecifiDevice
USB Connection
Built-in iSight
*Bellow is an example of what I see in my logs*
Sep 18 17:13:39 yazz-mac kernel[0]: USBF: 408.650 [0x4723a00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 4 of hub @ location: 0xfd000000)
Sep 18 17:13:39 yazz-mac kernel[0]: USBF: 409.376 [0x4723a00] The IOUSBFamily has successfully enumerated the device.
Sep 18 17:13:58 yazz-mac kernel[0]: USBF: 427.990 [0x4723a00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 4 of hub @ location: 0xfd000000)
Sep 18 17:14:02 yazz-mac kernel[0]: USBF: 432.160 [0x4723a00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 4 of hub @ location: 0xfd000000)
Sep 18 17:14:05 yazz-mac kernel[0]: USBF: 434.990 [0x4723a00] The IOUSBFamily was not able to enumerate a device.
Sep 18 17:14:06 yazz-mac kernel[0]: USBF: 435.809 [0x4723a00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 4 of hub @ location: 0xfd000000)
Sep 18 17:14:11 yazz-mac kernel[0]: USBF: 441.327 [0x4723a00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 4 of hub @ location: 0xfd000000)
Sep 18 17:14:12 yazz-mac kernel[0]: USBF: 442. 53 [0x4723a00] The IOUSBFamily has successfully enumerated the device.
*Some info about my MacBook Pro*
Model: MacBookPro1,2, BootROM MBP12.0061.B03, 2 processors, Intel Core Duo, 2.16 GHz, 2 GB
Graphics: ATI Radeon X1600, ATY,RadeonX1600, PCIe, 256 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 667 MHz
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 667 MHz
AirPort: spairportwireless_card_type_airportextreme (0x168C, 0x86), 1.1.9.3
Bluetooth: Version 1.9.0f8, 2 service, 1 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Network Service: Parallels Host-Guest, Ethernet, en2
Network Service: Parallels NAT, Ethernet, en3
Serial ATA Device: ST9120821AS, 111.79 GB
Parallel ATA Device: MATSHITADVD-R UJ-846
USB Device: Built-in iSight, Micron, Up to 480 Mb/sec, 500 mA
USB Device: Apple Internal Keyboard / Trackpad, Apple Computer, Up to 12 Mb/sec, 500 mA
USB Device: Bluetooth USB Host Controller, Apple, Inc., Up to 12 Mb/sec, 500 mA
USB Device: IR Receiver, Apple Computer, Inc., Up to 12 Mb/sec, 500 mA
*Some info from System Profiler when the camera appears to behave correctly*
USB High-Speed Bus:
Host Controller Location: Built In USB
Host Controller Driver: AppleUSBEHCI
PCI Device ID: 0x27cc
PCI Revision ID: 0x0002
PCI Vendor ID: 0x8086
Bus Number: 0xfd
Built-in iSight:
Version: 1.84
Bus Power (mA): 500
Speed: Up to 480 Mb/sec
Manufacturer: Micron
Product ID: 0x8501
Vendor ID: 0x05ac (Apple Computer, Inc.)
--Hello Aaton
If you have not installed any new hardware since your MacBook Pro worked correctly, it is possible that your problem may be hardware related. Because of the intermittent nature of your problem, unless the problem is repeatable when running some particular software or performing some function that could indicate possible software or device conflicts, hardware problems in your Mac seems even more likely.
Unless you get better suggestions from iNtel Mac users, here are the common solutions that help most avoid a visit to their Apple Service Technician for the "in use..." or "no camera connected" errors. You have already tried some of them, but I leave the entire list for possible use by other readers.
None of the suggestions is complicated, but the only way to find which one will work for you is to try them one-by-one until you find the one that fixes your Mac.
(0) Disconnect any unnecessary peripherals while you do your testing to rule out possible conflicts.
(1) Restart your Mac. Sometimes that is all that is required.
(2) If you use VMware Fusion to run Windows on your Mac, consider disconnecting iSight from your Virtual Machine as recommended by user "The.VCI" in this post.
(3) If you use an HP printer/scanner with your Mac, consider the "daemon" suggestions from user "parkersal" in this post.
(4) Check for any running applications, Login Items, or widgets that can use your iSight. (It is easy to forget widgets like Mirror in your Dashboard.) As explained in Apple's iSight "Your camera is in use by another application" message, iSight can be used by one application at a time.
(5) Try every suggestion re: Built-in iSight in How to Troubleshoot iSight. Be sure to include the checks for whether the problem is "application-specific" and "user-specific".
Click here if you need help creating a new user account to check whether your problem is "user-specific" during Troubleshooting.
(6) If resetting or the other troubleshooting suggestions do correct your problem, try the following:
• Backup your Home Folder, or at very least, your important files.
• Repair permissions. (Click here if you need help.)
• Then download and apply the Mac OS X 10.4.10 Combo Update v1.1 (iNtel).
• Finish with another Permissions Repair, and then check your iSight again.
Users have reported fixes to a variety of audio, video, connectivity, and software conflicts and unreliability issues after properly applying Combo Updates.
(7) Some iNtel Mac laptop users have also reported success after unplugging their Macs and leaving the battery out for half-an-hour to overnight.
(8) If none of these suggestions work, contact your retailer, Apple, or your Apple-Authorized Service Provider for professional help.
EZ Jim
PowerBook 1.67 GHz Mac OS X (10.4.10) G5 DP 1.8 External iSight -
Built-in iSight problem on iChat w/ Macbook Pro
when i try to invite people to see my iSight, it says connection failed because Ididn't respond. This has happened almost every single time I have tried to connect. The only 2 times it has worked, one of the times it disconnected after a few minutes. The other time was just a few minutes ago when my dad and I connected with our iSights. Although it worked with my Dad and I, it didn't work with 2 other people both immediatly before and after my dad and I connected.
I found this answer but have no idea what it means. someone said it worked for them but i am not a computer genious. anyone know how to help?
the answer i found: If it isn't your Firewall settings, what kind of router are you using and does it use UPnP?
If it does, try toggling UPnP off and on again, then connecting. Also, you might want to try using a different MTU setting. The Ralph Johns site has some recommendations on values to use.
This happens to me with my brother and toggling the UPnP solves it (Netgear D834G router). However, if I turn off or reboot my router, I have to toggle the option once more to get video chats working again.
macbook pro Mac OS X (10.4.6)Hi Molly,
Ok UPnP stands for Universal Plug and Play.
This is a means where the Application on the computer instructs the modem to open the ports it needs.
It allows multiple computers and other devices on your LAN to use the same ports at the same time.
This means that the router or modem can be left in it's default mode which is likely to be DHCP.
Ok so now DHCP is a means whereby the router or modem gives out IP addresses to the devices and computers on your LAN.
Your computer keeps the same IP until the lease time runs out. If the computer is on and connected to the DHCP serving device then the DHCP lease is renewed. If it is off or unconnected at the time the lease runs out then the IP gets changed the next time the computer is tunred on. (with a Mac this also includes Sleep). It acts as if it is a new computer on the LAN is one way of looking at it.
So if you use Port Forwarding and DHCP there is a chance your computer's IP will change at times. As the Port Forwarding points to one IP on the LAN it may not always be pointing to your computer.
As you are using UPnP which means any IP can have the ports open it does not matter if your computer's IP changes with using DHCP.
Now your computer and modem (or router) can be set up so that the IP to the computer never changes. This is called Static routing.
It is created by turning Off DHCP in the modem or router.
A change needs to be made on the Mac in System Preferences > Network > Connection method >TCP/IP tab.
In the drop down that reads Using DHCP now needs to be changed to read Manually.
After this you need to type in the IP in the filed underneath that the computer is going to use.
Alonmg with the Subnet Mask and "router" IP info and possibly the DNS server info if you have it.
Now the IP you choose needs to be in the same range the Modem or router is using.
So if your modem is at 192.168.1.100 then your computer needs to be any number in 192.168.1.xxx except for .100 as long as it is between 1 and 255.
The other info should be copied from the Using DHCP settings
(Subnet Mask, DNS Servers and "router" IP address).
Hope this is some use.
11:03 PM Thursday; June 1, 2006 -
Macbook 10.5.8 Version Built in ISight problem with YM 3.0 beta version
I am using my Macbook built in ISight with the latest version of Yahoo Messenger for Mac, the 3.0 Beta. Every time i will use the YM webcam, it will only last for about 1 minute and will not work anymore. This is happening since i bought my macbook last November 2008. it will be a year next month and still the ISight is not working properly with YM. When i checked from the store where I bought my macbook, they said it happens in YM coz according to them YM is not yet fully applicable with apple laptop models and recommended to use other messenger instead. My family and friends are using YM only to keep in touch with me so I don't have a choice but continue using YM. Its really disappointing coz I even downloaded the other version of YM before this 3.0 version, but same problem still exists.
Can anyone help me on how can i fix this problem? or if there is really a solution on this..I've always wanted to have a macbook laptop but having this kind of problem really made me think if i did a right decision to buy this laptop. it is indeed an expensive laptop but i cant enjoy it fully...
please help me!!!Welcome to Discussions, Marianne Bayogos
Problems like yours, especially those involving known-unreliable (Beta) software, can be difficult to resolve. You need to start by troubleshooting to determine the source of the problem. Then you will KNOW what to fix. You seem like a fairly experienced user, so try any of the following you think might help in any order you like.
(0) You can use the suggestions in http://support.apple.com/kb/HT2090 to determine whether iSight is causing your problem. Be sure to try with more than one user account and with some other apps, too.
If your iSight works properly with all other apps in every user account you test, your Apple hardware and software is NOT the cause.
If you can eliminate iSight as the source of your trouble, you will need to either switch to other ways of communicating or troubleshoot other system elements that might be causing the problem. Here are some other things you can consider if you don't get better suggestions here.
(1) Sometimes a restart restores function on internet connected applications. Shut down everything and restart your entire system including modem, router, and Mac in that order. To eliminate possible communication hardware problems, allow self-test to complete on each device before starting the next.
(2) If you updated or installed any other software immediately before the problem began, check their websites to see if there are known issues with your system configuration or installation. If these are no know issues, carefully following the developers' instructions, reinstall any recent software additions that you think might be causing a conflict with YMM, use Disk Utility to repair permissions, and try again. Doing this reinstall will reduce the possibility that some recent addition might be conflicting with your new YMM Beta.
If you find conflicting software, follow the instructions and uninstall to see if removing it will restore proper function to your favored communications apps.
(3) Check YMM's Help: http://help.yahoo.com/l/us/yahoo/messenger/mac/mac3/index.html
for help with installation and communication requirements/ configuration topics.
If you do not find the answers there, check the dedicated YMM forum (use the "Ask Other Messenger Users" link on the help page) to see if your problem has already been solved by other users who post there.
(4) You can also take your MacBook to a different location and see if the connection works when you access the web via a different internet connection.
(5) I no longer use YM because I often encountered problems like those you describe, but my testing from several years back showed that Yahoo! seemed to support the Windows version of their messenger app better than the Mac version.
Because your iNtel Mac can use Boot Camp, VMware Fusion™, Parallels™, or VirtualBox to run Windows® software, there is another alternative available to you. Choose which method you want to use to run Windows®, add the required software to your iNtel Mac (if you have not already done so), and then install and use Yahoo! Messenger for Windows.
http://messenger.yahoo.com/platform/win
(6) If all else fails, and if your family and friends are willing to try something "new and improved" (does NOT work with Yahoo! Messenger), you can both install and try a different video chat app such as Google Talk or Skype.
(7) Alternatively, you can try the web-based video chat sites like http://www.mebeam.com/ or Defcom's recommended TokBok.
EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz w/Mac OS X (10.6.1) MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.1)
G5DP1.8GHz (10.5.8) G4 PowerBook 1.67GHz (10.4.11) iBookSE 366MHz (10.3.9) LED Cinema Display External iSight -
Macbook built in iSight problem.
I am having problems with my built in iSight.
I've tried to track all the way to see where is failing and I get the following on the Console Log.
Jun 15 22:53:11 frviana kernel[0]: USBF: 631.251 Built-in iSight[0x2be9b00]: error getting config. err=0xe00002ed
Jun 15 22:53:12 frviana kernel[0]: USBF: 631.760 [0x2b24f00] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 2 of hub @ location: 0x3d000000)
Jun 15 22:53:16 frviana kernel[0]: USBF: 635.601 [0x2b24f00] The IOUSBFamily was not able to enumerate a device.
It initially appers on the system information as an USB device but after I try to use it for the first time on any application, example: Photobooth I get this error and it disapeer from the system information.
I am running the following processes:
Active Memory: 110.25 MB
Free Memory: 836.90 MB
Wired Memory: 150.77 MB
Used Memory: 424.10 MB
Inactive Memory: 163.09 MB
Total VM: 7.10 GB
Number of processes: 53
ID Process Name User CPU RSIZE VSIZE
0 kernel_task root 2.30 50.96 MB 1,017.06 MB
1 launchd root 0.00 516.00 KB 27.66 MB
23 dynamic_pager root 0.00 168.00 KB 26.61 MB
27 kextd root 0.00 980.00 KB 27.53 MB
31 KernelEventAgent root 0.00 628.00 KB 27.18 MB
32 mDNSResponder root 0.00 1.12 MB 28.38 MB
33 netinfod root 0.00 564.00 KB 26.91 MB
34 syslogd root 0.00 420.00 KB 26.63 MB
36 configd root 0.00 2.20 MB 29.24 MB
37 coreaudiod root 0.00 1.10 MB 28.64 MB
38 diskarbitrationd root 0.00 1.04 MB 27.11 MB
39 memberd root 0.00 652.00 KB 27.64 MB
40 securityd root 0.00 2.20 MB 28.68 MB
42 notifyd root 0.00 460.00 KB 27.19 MB
43 distnoted root 0.00 816.00 KB 27.01 MB
44 DirectoryService root 0.00 2.46 MB 29.46 MB
45 blued root 0.00 2.12 MB 37.17 MB
50 coreservicesd root 0.00 8.96 MB 39.99 MB
54 update root 0.20 220.00 KB 26.59 MB
63 WindowServer windowserv 3.60 19.36 MB 339.29 MB
65 ATSServer frviana 0.00 6.23 MB 146.06 MB
66 loginwindow frviana 0.00 7.42 MB 351.14 MB /System/Library/CoreServices/loginwindow.app
76 lookupd root 0.00 1.23 MB 28.50 MB
87 crashreporterd root 0.00 204.00 KB 26.59 MB
122 sh root 0.00 616.00 KB 27.06 MB
123 OSXvnc-server root 0.00 3.04 MB 294.39 MB
124 dyndnsd root 0.00 7.89 MB 109.98 MB
128 translated root 0.00 248.00 KB 36.07 MB
146 nfsiod root 0.00 184.00 KB 28.61 MB
151 ntpd root 0.00 404.00 KB 27.07 MB
162 rpc.lockd root 0.00 192.00 KB 26.65 MB
170 automount root 0.00 1.11 MB 29.00 MB
175 mds root 0.00 3.88 MB 42.33 MB
180 automount root 0.00 1.07 MB 28.71 MB
185 mdimport nobody 0.00 2.38 MB 38.59 MB
189 httpd root 0.00 1.44 MB 28.15 MB
190 httpd www 0.00 408.00 KB 27.72 MB
191 pbs frviana 0.00 2.05 MB 54.16 MB
197 Dock frviana 0.00 4.32 MB 348.64 MB /System/Library/CoreServices/Dock.app
198 SystemUIServer frviana 0.00 7.82 MB 347.52 MB /System/Library/CoreServices/SystemUIServer.app
200 Finder frviana 0.00 15.09 MB 362.47 MB /System/Library/CoreServices/Finder.app
202 mdimport frviana 0.00 3.50 MB 60.37 MB
204 Microsoft AU Daemon frviana 0.00 8.72 MB 400.53 MB
205 iTunes Helper frviana 0.00 1.72 MB 326.04 MB
206 iCalAlarmScheduler frviana 0.00 3.61 MB 330.61 MB
214 System Profiler frviana 0.00 8.11 MB 346.67 MB /Applications/Utilities/System Profiler.app
216 Console frviana 0.20 7.97 MB 347.09 MB /Applications/Utilities/Console.app
222 System Events frviana 0.00 3.29 MB 293.91 MB /System/Library/CoreServices/System Events.app
225 TextEdit frviana 0.00 7.61 MB 347.31 MB /Applications/TextEdit.app
226 AppleSpell frviana 0.00 1.90 MB 37.75 MB
230 cupsd root 0.00 1.63 MB 27.85 MB
232 Activity Monitor frviana 10.70 12.18 MB 435.16 MB /Applications/Utilities/Activity Monitor.app
233 pmTool root 0.80 1.17 MB 36.45 MB
Any idea? It has been 3 days only that I bought the Macbook.
Thanks,My macbook had the same problem. It began after I installed bootcamp, which I have since updated to 1.1. Whenever I boot into windows xp and then back into Os X, the isight stops working. In photobooth I get a blank green screen with a few scribbling lines of static at the top, but in ichat I get the "in use by other application" error.
I tried a system X reinstall, a bootcamp reinstall, zapping the PRAM, etc. etc. What really killed me was that the isight camera continued to work FINE in windows, but not at all in Os X (I could almost hear Bill Gates snickering).
The solution turned out to be resetting the power management unit by unplugging, removing the battery and holding down the power button for 5 seconds. Works without having to zap PRAM after.
The annoying thing is that I have to do this EVERY TIME after I have booted into windows if I want the camera to work in Os X.
As other users have pointed out, bootcamp now includes a package that updates the isight firmware.
Interestingly, this does NOT happen on my intel iMac, only the macbook.
I'm hoping for a more elegant fix.
Anyone else?
Jason
Maybe you are looking for
-
We have a new computer and lost our music from the old computer. How can i get it back or get it from the ipod touch to the new computer and my iphone?
-
Restore Itunes Library - Hard Drive Crash - from Ipod
I have a very large library of music - Many CD's - I have been able to restore my purchases from Apple store - My Ipod has 80 to 90% of my music on it - I do not wish to have to reload around 100 CDs of music - Is there a way to get the music that is
-
Need to attavh a file with email message
Hi All, I need to attach a file to the email message, for the same I am using the function module SO_OBJECT_SEND. but coudl not succeed. Can any one have insight over the function module that how I can use it for a attching a mail to email message. P
-
Open CS5 documents in InDesign CC
When opening InDesign CS5 files in InDesign CC it is opening up as "converted" and forcing us to "Save As". Is there an easy way to forcibly overwrite the document instead of save as? We're having the same problem with InDesign server scripts failing
-
Where can I find my movies saved in itunes media file
I have followed itunes' suggestion to back my movies in itunes media files, now I can't watch them because apparently itunes can't find the original file. When I try to locate these files they do not appear under the itunes media files. Help me pleas