Multiple mics, which channel for mic when assigning after aggregate setup

So I have read all the tutorials on setting up an aggregate device as I want to setup 3 mics for our podcast. I had some difficulties, and have a quick question. When I am assigning the channel to the track, can I assume I am assigning the mic to that track?
When I am assigning the channel to the track it shows that I have 6 mono channels to choose from but only 3 mics were assigned to the aggregate device. I am assuming it is doing this because each mic is 2 channel, so then which channel do I assign to each track if each mic has two channels?
Some guidance would be great!!

mwright1978 wrote:
Do we know why GB is assigning the different channels and not one channel?
it's the mic that's sending its signal to both channels.
What are the channels that will not respond channels to?
none, they should all work
Are the dual channels with the mics supposed to be stereo sound
very doubtful.
even though one mic, one sound, considering stereo needs to be from two mics giving the listener one sound in one ear and another in the other ear.
you understand correctly, single stereo mics are fairly rare.

Similar Messages

One or two LAG port-channel for 5508 v7.4 in HA setup?

Hi group
I have a question regarding LAG in HA setup; do you configure two port-channel, one for each controller or, only one port-channel for both?
I have a stack of 3 x 3750x, and 2 x 5508 with each two Gigabit uplink in use.
Active controler (5508-1) is connected to stack switch 1 and stack switch 2.
Standby controller (5508-2) is connected to stack switch 2 and stack switch 3.
I cannot find any documentation or guidelines for configurations of LAG in HA setup.
P.S. my question is not how to configure LAG or LACP, it only if you use one port-channel consist of 4 gigabit ports, or you have two with each 2 gigabit port to each controller.
TIA,
Peter

Thanks Stephen for your reply.
The switch doesn’t see which of the two port-channel that is on the active controller right?
If WLC01 is the active one in PO1 and standby is WLC02 in PO2, the MAC of the active controller (WLC01) will be sending on PO1.
When failover to standby, the MAC of WLC02 will be sending on PO2. As I see it, it is same IP address (management IP address of WLC01) but different MAC address – from WLC02.
So why could it not be one Port-channel, both controller will use one and same config when it become active?
TIA
Peter

One billing document for multiple deliveries which are for different PO

Hi All,
I have a scenario where i need to create one billing document for multiple deliveries.
Payer is same
Ship-to is same
PGI date different
Sales area is one
PO different
In standard SAP it will create seperate billing document for different PO
Please advice if there is a different copy routine which will combine all the POs in one billing document.

Hi Mr. Bhat,
Go to VTFL --> Select the combination of your delivery type and billing type --> Double click at Item(Left side) --> Select your item category --> Click at details
In the feild "Data VBRK/VBRP" --> I think the routine assigned is 601 (Inv.split - PO Num.) --> Now change it to 3 (Single invoice)
Then try your process, Hope it helps.
Regards,
MT

Cannot search for name when assign questionnaire in E-Recruitment

Hi,
I am currently using e-recruitment (version 603), we have a problem where when we try to assign a questionnaire to a person, we can't search this particular person. The name was not displayed on the searched result list. But when I checked using BP, HRP1000 and HRP5102 I can see the record of this person. Any ideas why this persons does not appears on the search result?
Rgds
Ridzuan

Nicole and Roman
Thanks for your feedback. Nicole, yes your are right I am referring to the processor, this person does have BUP003 role. Roman, I have also checked the infotype 5102, the field IS_INACTIVE is NOT set to 'X'.
For you information, what I found was this person have an empty Address under Address Overview when I run the BP transaction for his profile. Once the address field was filled with his address, we are now able to search for his name and assign him as the processor.
Your feedback have help me to solve this issues, once again thank you.
Rgds
Ridzuan

Which mac is best when using after effects and video editing?

i'm looking to get a new mac to do video edititng and adobe after effects. What should i get? A mac book pro, imac?

I'd get a MacPro with a lot of RAM. This gives me a platform I can expand through third party video i/o cards,esata cards for external RAID boxes, extra internal drives, multiple monitors, etc and will have the longest useable life span.
Your mileage will vary.
What it comes down to is ... Best is a subjective concept.
Best at what?
Absolute speed? Flexibility? Expandability? Life cycle costs? Low cost of entry? or ???
Define your needs, long term plans and budget more closely and what machine to purchase will become obvious.
x

Can I use a Bluetooth headphone/microphone for capture sound instead of normal iPhone mic when shooting video?

Can I use a Bluetooth headphone/microphone for capture sound instead of normal iPhone mic when shooting video?
The sound when I record video is not so good, so I'm trying to use the Bluetooth headphone/microphone to capture a person voice but not know which setting to use.

Hi Robert
Thanks for answering. I didn't know where to post other than the bluetooth forum which is relatively quiet and had no answers forthcoming.
Yes the voice isn't reaching the amp although it is registering on the input bar in the Sound System Prefs, just won't "play through" as it were. I can't see how it could be done I was just hoping someone might see something I am missing.
It seems a shame that you can't do it as iTunes on an old iBook makes a good juke box for DJ'ing and with everything becoming wireless these days it seems sensible that you could cut that one last wire.
Mike

How to do register-level programming for NI6025E when I want to acquire single scan incuding multiple input channels?

How to do register-level programming for NI6025E when I want to acquire single scan incuding multiple input channels?

Thanks, Alan, I think I indeed need to combine aiex1.cpp and aiex2.cpp. I made a change to Configure_Board of aiex1.cpp as follows:
//Call this function to configure board options.
void Configure_Board(tSTC *theSTC,tESeries *board)
//Clear configuration memory
theSTC->Write_Strobe_0.writeRegister(0x0001);
//Clear ADC FIFO
theSTC->Write_Strobe_1.writeRegister(0x0001);
//Writing to Config_Memory_High_Register for channel 1 settings
board->ConfigFifoHigh.setChannel(0);
board->ConfigFifoHigh.setBank(0);
board->ConfigFifoHigh.setChannelType(board->ConfigFifoHigh.kChannelTypeRSE);
board->ConfigFifoHigh.flush();
//Writing to Config_Memory_Low_Register for following channel 1 settings
board->ConfigFifoLow.setLastChannel(0);
board->ConfigFifoLow.setGeneralTrigger(0);
board->ConfigFifoLow.setGain(board->ConfigFifoLow.kGain001_0);
board->ConfigFifoLow.setPolarity(board->ConfigFifoLow.kPolarityBipolar);
board->ConfigFifoLow.setDither(0);
board->ConfigFifoLow.flush();
//Writing to Config_Memory_High_Register for following channel 0 settings
board->ConfigFifoHigh.setChannel(1);
board->ConfigFifoHigh.setBank(0);
board->ConfigFifoHigh.setChannelType(board->ConfigFifoHigh.kChannelTypeRSE);//RSE mode
board->ConfigFifoHigh.flush();
//Writing to Config_Memory_Low_Register for following channel 0 settings
board->ConfigFifoLow.setLastChannel(1);
board->ConfigFifoLow.setGeneralTrigger(0);
board->ConfigFifoLow.setGain(board->ConfigFifoLow.kGain001_0);
board->ConfigFifoLow.setPolarity(board->ConfigFifoLow.kPolarityBipolar);//BIPOLAR
board->ConfigFifoLow.setDither(0);
board->ConfigFifoLow.flush();
return;
and a change to test(iBus *bus):
do
  uStatus = theSTC->AI_Status_1.readRegister();
  if (!((uStatus & 0x1000) == 0x1000))
  uValue[i] = board->AIFifoData.readRegister();
   i++;
} while(i<1);
printf("Value %d is %6.2f\n",0,FindADDouble(uValue[0]));
printf("Value %d is %6.2f\n",1,FindADDouble(uValue[1]));
but it doesn't work, why?
How shoud I do?

OS X 10.8 How do I add aggregate devices for multiple mics in GB and LP9

How do I create aggregate devices in Mountain Lion OS X 10.8? I'm using Garageband and Logic Pro 9 and want to record with multiple mics.

In Lion and Snow Leopard, aggregate audio devices are created in Audio Midi Setup.app. I'm not at my ML Mac right now, but I imagine it's the same. It's in the Utilities folder.
HTH.

Multiple mics to macbook

Hey guys I need some help with tech issue.
My department has a weekly talk that is presented in a ampitheatre and broadcasted as a webinar. We are using WebEx. We are having issues with the audio quality especially when people in the amphiteathre ask questions.
I am looking for a multiple mic configuration that I can hook up to my Macbook when presenting this way the audience questions would be clear.
Which accessory / software do you recommend? Typically we will need 2-3 mics.

Very easy, same as I use and best solution, you can have up to 6 mics
ZOOM H6
http://www.amazon.com/Zoom-H6-Portable-Digital-Recorder/dp/B00DFU9BRK/ref=sr_1_c c_1?s=aps&ie=UTF8&qid=1393794895&sr=1-1-catcorr&keywords=zoom+h6
$400
has USB feed to any computer, you can record to any audio application, like Adobe Audition, or Logic Pro, or Sound Forge,
etc. etc.
Or, you can use it by itself and then upload later to your Macbook. Best new audio recording gadget out there.
We are having issues with the audio quality especially
There exists no better portable audio quality than the Zoom H6 unless you spend $2000+ on a portable audio recorder used for live shoots and professional movies.
however even those devices are recording at the same quality sampling rate in WAV.

Multiple Prepayment for a single Assignment or specific Assignment Set

Hi Everyone
I am working in Payroll Department, and I had a difficulties of running more than one prepayment for the same. We need sometime to pay for an employee a specific element like "Official Assignment Compensation" before the end of the month and we use Quick-pay by select specific element. then I use Prepayment. In the end of the Month, when I do run to the remaining elements it had no problem. but when I do re-prepayment it return to the first prepayment the quick-pay run not the payroll run.
I appreciate if anyone can explain how to do more than one prepayment for a single employee in a single period.

Thanks alot ysaadeh
I did managed to do it by doing the following steps:
- Quick Pay for a single employee
- Pre-Payment for this Quick Pay
- Bank Transfer Report - which shows the Employee No, Employee Name, Employee Bank Name and Ban Account Numbers and Amount for the Quick Pay
Then
- Payroll Run @ the end of the Month
- Pre-Payment for Payroll Run
- Bank Transfer Report ..
It worked fine. But I notice one thing. When I do pre-payment for Payroll - the second pre-payment, Bank Transfer Report only take the Data from the last Pre-Payment.
I cannot do the Bank Report for the Quick Pay After Running the Payroll Pre-Payment ..
Is there some way I can use Bank Report for these Both Pre-Payment
and Is there a way I can use Quick-Pay for a set of Employees - An assignment Set .
Thanks again and appreciate you feedback.
Regards

Monitor multiple channels for analog trigger with DAQmx drivers

Hello! I would like to start a data acquisition of multiple analog channels (16) from an analog trigger. I would like trigger to monitor four of the (same) channels, and trigger when any one of them reaches a certain voltage. I found an example that would work with the Traditional DAQ drivers (using occurances), but can't figure out how to do something similar in DAQmx.
Time is also an issue, as I would like to collect the first 80 milliseconds of data after the trigger (at a rate of 500,000 Hz).
I'm using LabView 7.0 and collecting data off of two PXI-6133 cards.
Thanks for your help!

Hi Denise-
After some research, I have found that it is not possible to use the functionality of DAQ Occurrences in DAQmx. Ironically, the reason that this functionality is available in Traditional and not DAQmx is due to the exploitation of an inherent limitation of Traditional that was upgraded in DAQmx. The multi-thread capability of DAQmx is a major advantage for most applications, but in this case it prevents the use of occurrences as they existed in Traditional DAQ.
In short, this means that you can't directly use this functionality in DAQmx. You can however emulate this functionality with minimal software analysis of the incoming signal. I have attached a modified example VI that logs data to a chart only when the analog level of one of the channels being measured has exceeded a user-defined reference value. Basically, the task is running continuously in the background but the data is not actually logged until the signal is above a predetermined "trigger" level.
Please let me know if the attached example is helpful for your application. You will see the input channels listed in the format "DevX/ai0:y" where X is the device number and y is the highest channel number of interest.
Regards,
Tom W
National Instruments
Attachments:
Cont Acq&Graph Voltage-Int Clk Analog SW Trigger.vi ‏83 KB

Dump thrown when tcode for screen painter assigned

HI guys,
I have created a screen and wanted to check how it looks at runtime, for this i assigned a tcode to the report. Now when i run the tcode it throws a dump. the dump is as follows.
The CONTROL "TCTRL_ENTRY" was searched for but not found.
These is either an inconsistency between the screen and the program or
an incorrect ABAP statement (for example, REFRESH CONTROL .. FROM SCREEN
with incorrect control name).
    MODULE STATUS_1000 OUTPUT.
     SET PF-STATUS 'SCR_1000'.
     SET TITLEBAR '001'.
ENDMODULE.                 " The pointer for error is at this line
What could be the possible error?? please let me know.
Thanks in advance...
Regards,
Navin
Edited by: navin.c on Mar 25, 2009 8:18 AM

Do your main program have the piece of code like the following?
CONTROLS:TC_9998 TYPE TABLEVIEW USING SCREEN 9998.
This way you have to declare a table contol. Do it simply with your Table Control name and the screen in which you are using it.E.g. in my case screen is 9998.
regards.
Sarbajit

Problem of Creating Multiple Communication channels for multiple files

Hi Everybody
I have a very basic doubt but this struck me...
For a file-XI-file scenario,if multiple files are coming from same FTP server but with different names then we have to create multiple communication channels for all the files of different names..but is this a intelligent approach?Can we do something so that only one communication channel can receive multiple files of different names?plz explain in detail if possible ASAP.
I have another doubt as in File-XI-File scenario how the XI understands that a particular file is from this FTP server needs to be send to another particular FTP Server?is it only the name of the file which we give in sender comm channel & receiver comm chaneel which determines this????that means this name should always be same?plz explain in detail if anybody knows?

Thanks Aamir.I understood the solution.
Correct me if I am wrong.......
1)If there are multiple files with different names & different extensions in the sender FTP then we use-->
2)if there are multiple files with different names & different extensions in sender FTP & I want only say files of 2 extension types(say .xml & .txt)then we use-->
*.xml
in one comm channel &
*.txt
in another comm channel rite??
Also I wanted to ask that only two kinda files we can pick up through sender comm channel rite?
.xml and .txt(File content Conversion).Can we pick files of other extensions also?(say .doc,.xls)If we use as u said
then files of all other extensions will also be picked up rite?bt hw will xi convert them into xml?plz explain......
One of my other q is not answered yet.........all these same doubts are there for receiver communication channel.......but you all have not said nething abt the receiver comm channel........plz explain the answers to all these queries for receiver comm channel for a receiver FTP........ASAP......thanks once again.......

I have problem with my mic when i make call the others cannot hear me but the mic is ok

i have problem with my mic when i make call the others cannot hear me but the mic is ok i checked it out and it works dont know what to do help me !!

Hello Sabbir Khan,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Can't hear through the receiver or through speaker, and can't be heard
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Best of luck,
Mario

How do I copy my old xl files from my XP machine to operate on xl for Mac on my new iMac. When I copy them onto a stick and transfer them it automatically makes them xls files which are then corrupted when I try to open them in xl for mac

How do I copy my old xl files from my XP machine to operate on xl for Mac on my new iMac. When I copy them onto a stick and transfer them it automatically makes them xls files which are then corrupted when I try to open them in xl for mac

Sorry, yes this is Microsoft Excel. The Microsoft XP has Excel files denoted as xl, the later versions of Microsoft Excel are denoted as xls files. The later verions of Microsoft Excel open the xl files OK, does Excel for Mac not able to do this?

Multiple mics, which channel for mic when assigning after aggregate setup

Similar Messages

Maybe you are looking for