Multiple Nics and Multiple Connections

After much researching I still have no answer to this question....
Is it possible to set up a Netware 6.5 server to handle communications
from two networks using two seperate nics?
The senario is this:
Our netware 6.5 server has two nics. Into one we have our local wan and
into the other we have a cable line to the internet. We would like to
make the netware 6.5 server an ftp server and handle the traffic of the
ftp to the outside world on the cable line on the second nic. But, also
be able to be accessed by the local wan via the first nic. Is this even
possible?
Thank you so much for the help!

What do I define the Network IP address and the subnet as? Is the ip
address the ip address of the server? The next hop on the router is
already filled in.
VIPA is disabled.
> You only want one of the static routes to be of the type "default
route".
> In your case, I'd say the internet connection should be the default
route.
>
> Change the 10.x.x.x to Network and fill in the Network IP address,
subnet
> mask and next hop router with appropriate information. Once this is
set up
> correctly, you should be able to communicate with the server from the
inside
> with the outside NIC connected.
>
> I'm not certain, but do you have VIPA enabled? I believe you would
want it
> disabled.
>
> <[email protected]> wrote in message
> news:[email protected]...
> > Yes we have workstations in other locations, they don't access the
> > internet through the cable connection.
> >
> > The cable connection comming in is on it's own router. The only thing
> > that is connected to the router/cable connection is the secondary nic
of
> > the novell 6.5 sp6 server. We would like it to only be used for
ftping
> > to this novell server.
> >
> > The primary nic of the same novell 6.5 server is connected to the
> > 10.x.x.x network with it's own router and connection to the wan.
> >
> > LAN Static Routing: Enabled
> > Default IP Address: 10.1.x.x
> >
> > There are two routes listed here they are:
> >
> > Route Type : Default Route
> > IP Address of Network/Host : (blank)
> > Subnetwork Mask: (blank)
> > Next Hop Router on Route : 71.x.x.x (this is the cable's connection
> > gateway)
> > Metric for this route : 1
> > Type of route : Passive
> >
> > Route Type : Default Route
> > IP Address of Network/Host :(blank)
> > Subnetwork Mask:(blank)
> > Next Hop Router on Route : 10.x.x.x (gateway)
> > Metric for this route : 1
> > Type of route : Passive
> >
> > Again, I thank you so very much for your help.
> >
> > -Chris
> >
> >
> >> The diagram is very helpful -- thanks. So I presume your router has
2
> >> internal ports, one on the 10.x.x.x LAN and one on the 192.168.1 LAN
> > (which
> >> appears to be functioning as a DMZ)? If yes, then I see no problem
with
> >> the setup as shown, but yes, there are some routing considerations...
> >>
> >> What is the default route (gateway) on the server? See INETCFG -->
> >> Protocols --> TCP/IP --> LAN Static Routing Table
> >>
> >> And what do your workstations use as their default gateway -- is it
the
> >> 10.x.x.x address of the router?
> >>
> >> And you mentioned a WAN in an earlier message, so are there
> > workstations in
> >> other lcoations (on other IP networks) that access this server? If
> > yes, do
> >> they get to it through the Cisco router?
> >>
> >> --
> >> bd
> >> NSC Volunteer SysOp
> >>
> >
>
>

Similar Messages

Recommended configuration for load balanced Portal with load balancer, multiple gateways and multiple servers.

Does anyone have a recommended network, hardware and software configuration guide for a Portal installation running with multiple gateways load balanced (ie one URL) that talk to multiple servers?

David,
We've used Resonate (software) to load balance the gateways. It allows
you to group all the gateways under 1 virtual URL and load balance the
incoming connections over each gateway depending on the rules that you
define in Resonate. Look in the SUN portal whitepapers there is one that
talks about it specifically.
As far as load balancing the calls to the portals, the gateways will
automatically load balance across all the portals that they know about
using a simple round-robin rotation. You may be able to use Resonate in
front of the portals but you may need to activate persistance within
Resonate to ensure that the user always ends up on the portal that he
established his initial connection on (if you want that), check with Sun
on this one.
David Broeren wrote:
Recommended configuration for load balanced Portal with load balancer,
multiple gateways and multiple servers.
Does anyone have a recommended network, hardware and software
configuration guide for a Portal installation running with multiple
gateways load balanced (ie one URL) that talk to multiple servers?
Try our New Web Based Forum at http://softwareforum.sun.com
Includes Access to our Product Knowledge Base!

Can I use one itunes account for multiple users and multiple devices

Can I use one itunes account for multiple users and multiple devices?

The iTunes EULA, as I understand it (I'm not an attorney )for Apps is basically that one person can use an App multiple devices, or multiple people can use an App one device..so one to many or many to one, but not many to many....

Planning for product using multiple bom and multiple recipe involving SOP

Hi friends,
The problem. Currently we have maintained single BOM and single recipe (The BOM and Recipe used for MRP) for long term planning run. The FMCG sector of Client requested to have multiple BOMs and multiple recipes in the long term planning run. I.e. The planning is done quarterly and they wanted to use different BOMs and Different recipes for each quarter. But since the existing system has configured to use a single BOM and a single recipe we have a problem to use the long term planning run with the current setups.The problem we have is in this 001 planning scenario.
appreciate if you can help me how to accommodate multiple BOMs and recepis in the long term planning run.
thanks and regards
om

HI Mr. Ready,
We create PIR though a submit Job and in this case how to mention the production version while creating PIRs . Also if I am creating PIR through MD61 how to record the version.
Please advice.
Thanks and Regards,
Om

Posting an Idoc with Multiple Headers and Multiple Lines

Hi all,
I have a scenario like this fileXIIdoc
Invoice file comes in text file with multiple header and multiple lines like this
111               aaa     13214234    US   (header)
09082010     ABC    9999            A     (Line)
222               ccc     43454543    US   (header)
09082010     XYZ    7777            B     (Line)
09082010     PQR    8888            C     (Line)
I need to post single Idoc with all the headers and lines
we are planning to use Custom Idoc,Is this possible by having the header segment as unbounded??
Regards
Edited by: Vamsi Krishna on Sep 8, 2010 8:05 PM

hi,
lets go again.
you have to edit the custom IDoc and change the ocurrance on the header segment. also modify the details segment adding an addtional field that identify which header that this detail belong.
for this case you cannot change the occurrance in SAP PI because you wont identify what i have told you before. in PI apply to change the occurrance if you could send ONE Idoc Per Header.
now is better clear???
Let us know.
Thanks
Rodrigo P-.

Partial-credit scoring in multiple response and multiple hot-spot questions

Hello everyone,
I'm calling on your generosity in the spirit of the holidays to help out a noob. I would like to create matching, multiple-response and multiple-hot spot questions where the user receives credit based on the number of correct answers within the question. For example, in a matching question where there are four items; if the user gets 2 out of the four items matched correctly, I would like for him to receive 2 out of 4 points.
I understand that Captivate doesn't support partial-credit scoring of this type, but a few posts have implied that it can be done with variables. Is there anyone who can walk me through this process, or send me to a link that will walk me through it? (I've scoured these forums and tried the Cp tutorials, to no avail.) And if it's not asking too much, please make it understandable to someone who has very little experience with variables.
Thanks, and Merry Christmas.
JR
(Running CP 5 on Windows Vista)

Hello,
I did publish an article more specific on partial scoring, perhaps this could help you:
Partial scores and customized feedback
And since you are asking for more basic information, on my blog I point to some other articles to explain the meaning of variables with/without advanced actions. Feel free to have a look (there are more postings about advanced actions and links to articles over there):
Curious about variables ?
Unleash the power of variables with advanced actions
Lilybiri

Diff between Multiple Threading and Multiple instance.

Hi ,
what is the main diff between Multiple Threading and Multiple instance?
Please give me the answer

Satti4Java wrote:
Hi ,
what is the main diff between Multiple Threading and Multiple instance?The main difference (not "diff") is that the first one ends with the word "Threading" and the second one ends with the word "instance".
Really. Seriously. Now if you had some industry standard phrases you were comparing, there might be a useful discussion. But those are just words strung together. If that's a homework question, I recommend you find a different teacher.

Oracle HR restrictions based on multiple assignments and multiple GRE's.

In oracle HR, with multiple assignments and multiple GRE. How can we restrict to having 1 assignment per GRE. I do not want more than 1 assignments per GRE. Has anyone done this before?

Hi,
If the requirement is to prevent the creation of multiple assignments, you can achieve that by personalizing the assignment form.
Thanks
Satheesh

Multiple rows and multiple cols inone report

Hi
All
I have a req where i need to build a report with multiple rows and multiple columns
.... ....................... 2009 jan , 2009 feb , 2009 march , 2009 april...........................
............................ dim3 mem1 , dim3 mem1 , dim3 mem1, dim3 mem1..........................
dim1 mem1
dim2 mem1
calc value
dim1 mem2
dim2 mem1
calc value
dim1 mem3
dim2 mem1
calc value
please advice if i can use the colkey range and rowkeyranges for this type of expansion and how?
thanks
Edited by: bpc_now on Oct 21, 2010 6:40 AM

Hi,
If you need multiple dimensions, then the first thing is to specify EVDRE("mXn")
where m = number of dimensions in column
n = number of dimensions in the row.
If the EVDRE has already been built and you wnat to change it, then you need to change the rowkeyrange and colkeyrange. And accordingly, you should have 4 expansions - 2 for rows and 2 for columns.
Hope it helps.

Multiple sizes and multiple quantities of an item

How do I create a shirt order form where someone can order multiple sizes and multiple quantities of an item?

Hi,
There’re some order templates, Shirt(Clothing) Order Form, that might be meet your request. Or you can design a custom form according your requirement if you’re a form author or coauthor. For your case, when you design the form, you can choose the multiple choices, single choice, or other fields, etc. And you have to enable the payment under options tab, and assign fields as a purchase fields. At the same time, you can share the web form to the form filler to make an order.
Thanks,
Guanshuai

Synchronize multiple tasks and multiple boards with X-series USB devices

Hi all,
I am trying to figure out how to synchronize multiple tasks across multiple X-series USB boards (6353, to be precise).
I have to run a digital output task AND an analog output task on each board. All four tasks (the DO and AO on Board 1, and the DO and AO on Board 2) must be synchronized.
I know how to synchronize multiple tasks on a single board. I've been doing that for years. That works fine.
I know how to synchronize a single task across multiple boards (say, a DO task across 2 different boards). That works fine too.
For the life of me, I can't figure out how to marry the two. Everything I've seen, all of the examples, etc. assume you want to do one or the other, or that you have a RTSI cable available. Are there any examples out there that synchronize multiple tasks across multiple USB boards?
I tried exporting the AO clock signal from my master AO task to PFI12, and then using the signal on PFI12 to as the clock source for the remaining tasks (Dev1/PFI12 physically connected to Dev2/PFI12, and Dev1/PFI12 set as the clock source for Dev1's DO task).
I have also tried setting Dev1/aoSampClock as the source for Dev1's DO task.
Under both configurations, I invariably get error -89137 when I try to start the tasks -- required resources (PFI12) in use by Dev1/do/SampClock. I understand what the error is telling me. What I don't understand is why I'm receiving this error when I don't have any of my tasks configured to use the DO Sample Clock. It seems as though it is not possible to export a clock signal to a PFI line and simultaneously run a clocked digital task, even if the clock source for that task is specified as something other than the DO Sample Clock?
So, my question is, is it possible to do what I want to do? And if so, how do I do it? How do I configure a common clock source across multiple tasks running on multiple USB boards?
Hoping for insight from those wiser than I...
Diane
Solved!
Go to Solution.

Update: I decided to try using a counter as the source clock. One cannot use counter 0 to accomplish this, but it does appear to work with counter 1.
I'll take what I can get. Fortunately I have two spare counters. (Yes, I'm running counter tasks too -- 6 of them -- but they don't have to be synchronized.)
I have to add both digital and analog input tasks as well -- all synchronous with each other, but not with the output tasks since they'll be running at different sample rates. I hope I'm able to use a counter as the source clock for those as well.
My head aches.

Multiple servers and multiple clients on one machine

Hi,
I was hoping someone could give me some direction as to how to go about creating multiple servers and muliple clients on the one computer using RMI and threads. I intend to have say 4 servents (able to perform both client and server methods) running on the one computer, with the clients being able to connect to each of the servers. (I'm doing this to emulate using 4 computers, which I don't have!). I know I have to use different ports to do this. How do I go about the following using RMI - start up a server (port number as argument from command line?), which starts a thread listening for connections from the other clients.. when a new connection is established between server and client, then start a new thread which 'handles' that connection.
The examples I've seen of RMI only deal with single server and single client... I'd appreciate any suggestions as to how to go about this problem!!

Hi,
I suggest not to use the rmiregistry program at all
but to start the registry in a program of your own.
Then you can specify all you need (url, port, even
client and server socket) as command line argument.
You need something like this:
Registry registry = null;
Remote server = null;
try
{ // this succeeds if the registry already runs
registry = LocateRegistry.getRegistry(yourRegistry);
server = registry.rebind( yourServer );
}catch( RemoteException )
{ // no registry reachable, create one
registry = LocateRegistry.createRegistry(yourRegistry);
server = registry.rebind( yourServer );
}Have fun,
wiedkla

TO DRAW A TABLE WITH MULTIPLE ROWS AND MULTIPLE COLOUMNS IN FORM

Hi,
How to draw a table with multiple rows and columns seperated by lines in form printing?

check this
http://sap-img.com/ts003.htm
Regards
Prabhu

DBMS_FGA.add_policy .. How to handle multiple tables and multiple users

Dear All,
My database is 11gR1 and Linux is the platform.
I have more then 50 very important tables and around 15 database users.
I want to implement fine grained auditing on these important tables.
This is how I am going to implement it:
SQL>BEGIN
DBMS_FGA.add_policy(
object_schema     =>     'Scott',
object_name     =>     'SAL',
policy_name     =>     'SALARY_CHK_AUDIT',
audit_condition     =>     NULL,
handler_schema     =>     'imran',
statement_types     =>     'SELECT,INSERT,UPDATE,DELETE',
audit_column     =>     NULL);
END;
what is i have to pass multiple tables in object_schema and multiple users in handler_schema.
I hope i am able to clear my question, any doubts please let me know.
Regards, Imran

Hi,
object_schema - The schema of the object to be audited. (If NULL, the current log-on user schema is assumed.)
in case if you like to audit for multiple users - then try to test by holding a null value and test access the important tables -where the relevant auditing records are generated as per your requirement or not. i have not tested.. try it
- Pavan Kumar N

Multiple users and multiple select options

Hi,
First of all, let me congratulate Oracle HTML DB team for this great product! This is extremely powerful and useful.
I have multiple selection item on the form to generate report for the selected multiple schools. I have two critical questions.
1) Currently I am deleting all records from database tables for multiples selects and similarly selecting all records from these tables to populate dependent LOVs and so on. This is a major issue when multiple people use this application at the same time. I looked at couple of examples to create, delete and select records based on IDs (unique) and it is not clear to me if I need to create parameter/hidden params on the reports side or on the HTML DB side or .. how do they communicate etc. Could any one clarify this process of checking for unique IDs please.
2) Is there any way to give an option to the user to treat multiple selected item as just one single and to treat them separate? For example, if we let the user count number of students at two schools, how can we let the user count two schools separate as well as both schools together? This should also further ask for the possible options separate for both schools separate if they were to run separate.
This is very important for me and appreciate any help from you. Thanks in advance.

Hi,
Could any one point me in the right direction, please!
Thanks,

Multiple Nics and Multiple Connections

Similar Messages

Maybe you are looking for