Multiple phones connected???

Help please
Why does my wifes n95 now says multiple phones connected when connected to pc suite,also non compatible mode in bottom tray-also won't allow back up as files being used,I must have altered a setting somewhere,althuogh i seem to be using the same connection procedure,any help appreciated

Mac OS X > System Preferences > Bluetooth > Devices > select desired device > Create Serial Port (at the left) > + > enter a name you like > select the Dial-up Networking profile > tick all checkboxes > OK
This should create a new port within System Preferences > Network which allows you to connect to a different phone just as you like.

Similar Messages

Help needed: PC suite shows multiple phones connec...

PC suite shows multiple phones connected after updating the firmware of nokia N73 music edition phone. I get a pop up as soon as I connect my phone, which says that the phone has been connected in an unsupported mode. But I always use the PC suite mode. This issue started soon after I updated the firmware. I had installed the Nokia updater software which installs some drivers for the cable.
Has anyone faced the same issue. Please help me out.

Im also facing the same problem.
Any one is ther to help Us?

Wireless phones drop connection when multiples phones on same AP

I'm attempting to find a solution as to why wireless phones drop the calls when there are multiple phones associated with an AP. The BW usage of the phones is a small fraction of the available BW. Call quality is OK with multiple phone associations, and a single phone on an AP does not drop a call.
There doesn't appear to be any pattern associated with the dropped calls. Not every phone drops a call, but this happens frequently.
Thank you.

Are these Cisco APs? If so, can enable QBSS.
For Cisco IOS, enter "dot11 phone". For Airespace is called "AP CAC Limit" in the WLAN config. This will send a Channel Utilization value to the phone for that AP's channel. If 12.3(7)JA or later, this will be CCA based value showing true channel utilization. This is on a 255 scale, where default limit for calls is 105. Can still receive incoming calls though when > 105.
The phone call shouldn't be dropped though even if AP association is lost, unless some device is disconnecting the call due to not receiving any RTP packets (i.e. Cisco CallManager Express). If this is a 7920, go to the 7920 site survey to view the CU value. The last # displayed will be the QBSS / CU value. If this somewhat > 0 (i.e. 30+ or so) without any 802.11 traffic present, then may want to investigate what devices or causing this load on the 802.11 channel. An option could be to move to another channel as well. Ensure non-overlapping channels are used though per 7920 scanning mechanism and to ensure seamless roaming.
If these are 7920s, recommend using 3.01 fw.

Our home network has multiple devices connected by iCloud. Having problem with Calendar. On one iMac, all the events are duplicated. How can I correct that problem? Under the Calendar accounts, I had my Apple id listed and also just iCloud.

Our home network has multiple devices connected by iCloud: 2 iMacs, 2 iPhone 4s, 1 MacPro Laptop, and 1 iPad 2. When using Calendar, all the events were
duplicated on my husbands iMac. On his computer, under Calendar accounts, I had included iCloud and also my iCloud ID. I thought that because I had two accounts listed that were connected to iCloud, that might be the cause of the duplication. When I deleted ithe calendars from one of the accounts, it resulted
in deleting all of the events on all of our network devices!
I have since entered some new events into Calendar from my iMac and from my iPhone. These appear correctly on all devices except my husband's iMac where they are again all duplicated.
I have two questions: 1) How can I eliminate the duplicated events on my husband's computer and 2) How do I retrieve the old wiped out Calendar events from
Time Capsule. I don't know how to find Calendar in the Time Capsule. If I find the Calendar information in Time Capsule, how do I transfer it to my current Calendars?
I was obtaining phone help from one of the Apple techs at Apple Support, but our call was disconnected part way through. Didn't know how to reconnect with the tech.
Thanks for any help.

The warranty entitles you to complimentary phone support for the first 90 days of ownership.

How to provide access to multiple users connected to a Dumb switch? (multi-auth/multi-domain)

Good morning everybody,
I am writing on behalf of not being able to implement a desired outcome in our company network. In fact the situation is as follows:
What I want to do is to be able to authenticate users (802.1x authentication) in our company radius server and authorize them access by having a dynamic VLAN assignment in a multi-user environment on one and the same port of a Cisco 2960 switch. So far, the authentication and authorization has been working completely smoothly (there are no problems with itself). The concept involves the configuration of both DATA and VOICE VLANs as I there is also phone authentication implemented. In order to simulate this environment I introduce a Dumb switch connected to my Cisco 2960 Catalyst.
What I have successfully managed to get to work so far is this:
1) On one switch port I have tried the “authentication host-mode multi-domain” and it worked perfectly for a PC behind a telephone, or with one PC connected to a the dumb switch + the telephone connected to another port of the dumb switch. Logically it is the same situation as there is a separation in two domains – DATA and VOICE. Bellow is an output from show authentication sessions for this scenario.
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
2) On the other hand, when I try the same scenario with the “authentication host-mode multi-auth”, the switch still separates the traffic in two domains and is able to authenticate all users, AS LONG AS they are in the same VLAN.
show authentication sessions:
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 b888.e3eb.ebac dot1x DATA Authz Success C0A8FF69000000F8008C (user2)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
However, I cannot succeed authentication of many users from DIFFERENT VLANs, neither in multi-auth nor in multi-domain modes.
What I want to get is an output like this:
Interface MAC Address Method Domain Status Session ID
Fa0/23 0021.9b62.b79b dot1x DATA Authz Success C0A8FF69000000F3008E (user1)
Fa0/23 b888.e3eb.ebac dot1x DATA Authz Success C0A8FF69000000F8008C (user2)
Fa0/23 0015.655c.b912 dot1x VOICE Authz Success C0A8FF69000000F9009F (phone)
I want the switch to authenticate the users anytime they connect to itself and for them to have an instant access to the network. (I tell this because I tried scenario 1) with multi-domain mode and authentication violation replace, and it worked but, two users never had access to the “Internet” simultaneously!!!
The configuration of the interface connected to the Dumb switch is as follows.
interface FastEthernet0/x
description Connection to DUMBswitch
switchport mode access
switchport voice vlan XXX
switchport port-security maximum 10
switchport port-security
switchport port-security violation protect
authentication host-mode multi-auth
authentication priority dot1x
authentication port-control auto
authentication timer reauthenticate 4000
authentication violation replace
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
The way I see it is explained in the following steps:
- PC1 connects to the Dumb switch. This causes the Cisco switch to authenticate user1. This creates an auth. session with its MAC address linked to a domain DATA.
- When PC2 connects to the Dumb switch, this causes the violation replace which replaces the recent authenticated MAC address with the MAC of PC2. I would like it once authenticated to appear in the authentication sessions with a link to a new DATA domain linked to the VLAN assigned from the RADIUS server.
Is this possible? I think (in theory) this is the only way to provide authenticated access to multiple users connecting through Dumb switch to the network.
Has anybody ever succeeded in such a configuration example and if yes, I would be love to get some help in doing so?
Thank you
Stoimen Hristov

Hi Stoimen,
I have done a setup similar to yours with the only exception being VLAN assignment. When I used dACLs only, it makes things somewhat easier as the VLAN no longer matters. Remember that the switchport is in access mode and will only allow a single VLAN across it (with the exception of the voice VLAN). I think that is the real cause of your problem.
From what I can see, you have 2 options available to you:
1) Use dACLs instead of VLAN assignment. This means that an access list will be downloaded from the radius server straight to the authenticated user's session. I have tested this and it works perfectly. Just Google Cisco IBNS quick reference guide and look for the section that deals with Low Impact mode.
2) Get rid of the dumb switches and use managed switches throughout your network. Dumb switches will always be a point of weakness in your network because they have no intelligence to do advanced security features like port security, 802.1x, DHCP snooping, etc.
Hopefully someone else will chime in with another option.
Xavier

Can I attach multiple phone numbers to my iMessage account?

So here's my predicament:
Any time I go travelling somewhere, I like to buy a local SIM card so that I don't have to pay fees for roaming data. The problem is that whenever I insert a new SIM card, iMessage switches to using my new (temporary) number and disconnects from my old (permanent) number. So any new messages I send will either send from this foreign number, or from my email; either one is inconvenient because it tends to start new threads for others in group messages and such. And people who try to iMessage my permanent phone number end up having it fail and then send it as a text message (which I will not receive until I get home and switch my SIM card back).
Is it possible to have multiple phone numbers connected to an iMessage account? (Without resorting to something drastic like buying more iPhones just to have more active numbers.) It seems like something that should be possible, but I can't figure out how to do it.

No, it isn't possible. But you can give Apple this suggestion here: http://www.apple.com/feedback/iphone.html.

Multiple phone hookup question.

How do I hook up multiple phones to a new digital voice installation?Can i just plug into my old phone system input bus?

There can be several ways to connect the eMTA to the inside phone wiring.
First step is to make sure the old telephone service is disconnected. This is normally at the NID, network interface device, the gray box on the side of the house. Unplug the small phone cord from the jack in the NID, and mark it so it will not be connected back by accident.
Once the inside phone wiring is disconnected from the old incoming ILEC service, it is safe to hook the eMTA to the inside phone wiring. Usually the eMTA is installed in a room that has a existing phone jack connected to the inside phone wiring in the home. Take a standard phone cord, plug it in the phone jack in the room and the other end goes to the L1/L2 jack on the eMTA telephony modem. That feeds the jacks in the home to the talk battery voltage on the eMTA and supplies your dial tone and ringing voltage to all phones connected in the home.
Special wiring needs to be done when there is a alarm panel in the home, normally the Comcast installer does this. If the room that the eMTA doesn't have a phone jack, then a inside wire needs to be installed to connect the eMTA to a different point where there is access to the inside phone wiring in the home.

Can you get multiple phone socket working with BT ...

Hi,
So I recently had a BT engineer visit, he connected the phone line on the main socket then left. A week later they turned my BT infinity on.
It works great but the main socket is in a different room to my office. I have a phone socket in my office right next ot my pc. But when i plug my router into this socket it fails to produce an internet connection.
Is there a way to get multiple phone sockets working? I would like to move my hub so it is in my office but the socket isnt giving off internet.
Any help is much appreciated.
Thanks.

You need to identify the cables connected to the removable faceplate beside the red arrow - these are the extension cables to other sockets in the house.
Connected from here you will get voice only - not data.
If there is more than 1 cable you need to identify the one to your office, remove it and fit the cables to the yellow arrow connections.
You only need to connect the cables connected to 2 & 5 (there may be more connected to the faceplate)
guide on this link although it does not tell you the 2/5 connection order - I don't think polarity matters - but someone with more knowledge can advise.
A potential problem you may have is if there are other extension sockets connected to your office socket you use (and not the faceplate) as these then are not suitable for phone - only data.
With DECT phones and the need for just one basestaion not really a probem nowadays but you need to know where each socket in your house is connected from, and what you want to use it for.
If you have any BB problems, BT will also insits you plug the router/modem back into the master socket for all testing.
EDited to add - a krone insertion tool is best for inserting the cables to the socket and has a nice pick to disconnect also. They are easy to use - search you tube for a video.

Multiple WLAN connections

Does anyone know of a way to get my PODCAST and Email applications to use multiple WLAN connections?
I spend most of my day in one of two places, each with a different WLAN, and I'd the phone to have the sense to change WLAN connection as they become available.
Thanks for your time.

Depends, on what your phone is.
If you're using an N97 or a 5800, or anything running on s60v5 for that matter, Go to Menu>Settings>Connectivity>Wireless LAN>Options>Settings>Show WLAN availability. Then you can also set how often it will set to scan for WLAN connections. This would allow the phone to scan for WLAN hotspots around you immediately. Be warned however that this will drain your battery faster.
On an s60v3 phone, I am not very familiar but from what I know its in Menu>Tools>Connectivity>Wireless LAN>Options>Settings>Show WLAn availability.
If you find my post helpful please click the green star on the left under the avatar. Thanks.

Monitor multiple phone for incoming call

Hello,
I want to monitor multiple phone incoming call (retrieve callerID, ...)
I do that with Tapi, but when you configure TSP, it's only for one phone
I can install TSP several times, but ... for 40 phones ...
Are there other solutions ?
I use CCME

Yes, you can use packet capture to sniff skinny. It works really well, and transparently across CallManager and CallManager Express. You'll need to perform packet decode which is a bit of work, and connect your server to the appropriate SPAN port, of course.

My imessages are being sent on multiple phones and i deleted the icloud account on the other phone but the messages still go through how do I stop this?

my imessages are being sent on multiple phones and i deleted the icloud account on the other phone but the messages still go through how do I stop this?
Do you think deleting the message off the phone would make a difference?

If you don't enter an e-mail address, it just uses SMS and MMS. iMessages (sent over the data connection instead of using your SMS messaging plan) require an e-mail address registered on the device.
There is no requirement that you activate it.

Just upgraded to iOS 7 and messages are showing up on multiple phones within our family. We all use the same iCloud account. I believe this happened the last time there was a major iOS upgrade but I can't remember what the fix was! Help!

The four members of my family just upgraded to iOS 7 last night. We now find that we are receiving each other's text messages. It's possible that during the installs, a few members may not have "unckecked" the multiple phone numbers they can be reached on. I know that I had to uncheck my husbands work mobile number and work email address as they came up as choices for contacting me. So now I am receiving some of my daughter's text messages on my phone - she's not impressed! My husband is receiving my texts etc... It's a mess! I appreciate any help anyone can offer!

I had this problem last night as well. Only my daughter upgraded to iOS7 and she had an old phone of mine. When she upgraded, the phone asked for my apple ID and then continued as normal. However, after the upgrade, any text message that I recieved, she also recieved. I am pretty sure my wife thought I was hammered when she started texting me and my daughter began answering her not having any clue what she was texting about. Anyway, this only occurred with texts from other family members, not from texts I received from friends who are obviously not on our account (we have Verizon BTW). To resolve this issue, and it isn't a short resolution.... there are two options... One, simply erase everyting on the phone.... I don't like iTunes 11, so we were unable to back up her phone. I made her go through her 600 photos, delete the ones she didn't want and email the ones she wanted to herself, and then we wiped the phone clean and rebooted it... go into Settings, General, Reset, Erase All Content and Settings. The second option, if you have iTunes 11 is to back up the phones one at a time, and then go into Settings, General, Reset, Erase All Content and Settings. Either of these options wipes the phone clean of all information, text contacts pictures etc and then you have to re-enter all of your individual information. When you do that, make sure that no one is on the same iTunes account. Theoretically, after you do this, you plug back into your computer and SYNC your phone from the last back-up. This resolved the problem for us. I don't know if there is an easier solution, be we tried logging in and out of our iTunes Accounts, turning the power on and off, and nothing changed. So, we had to go the more difficult route to avoid mass confusion with family texting.

We use our Iphones with the icloud to set up scheduling of jobs. Multiple phones share the same icloud for this purpose. We recently had a change in leadership. How do I completely delete the icloud account? Or do I just create a new one/forget old 1

Multiple phones share one Icloud account. We use it to schedule jobs and crew leaders read the cloud to get the information of the job that needs to be done. However, we recently had a change of leadership and we think this person might have logged into or put our cloud on his phone to sabotage our business. I changed the password but that didn't fix the situation. I could put a job on the cloud with an old phone that was logged in with the old password and everyone with the new password would still see the job. I have since created a whole new cloud account which seems to have eliminated the "future" issue of sabotage however I would like to completely eliminate that old account...any advise?

Everyone needs to go to Settings (or System Preferences)>iCloud and click 'Delete account' or 'Sign out' as applicable (it's the same thing). Then they can sign into the new account you have created and proceed from there. You can't actually delete the old account from the server but you can just ignore it.

I have a wireless home phone connect device. Can call out on it when dial tone present, but most times cannot receive calls since purchase. Anyone else having a problem with their home connect device?

Have had Wireless Home Phone connect device refreshed and updated three times since I purchased it in September 2014. Last tech I worked with on it initialized an NRB to check the network. I checked the location of the tower, which is less than one mile up the hill with clear line of site. The device always has two antennas on it. The device is great when it does work, but most of the time it rings three times and then jumps to an automated message saying the person I am calling is not available. I've actually gone up there several times to try an fix the device, but always end up calling a Verizon tech who has me unplug it, pull the battery, and they do some network stuff and then we turn it back on and it works. After the last time on 10/02/14, I called it and got the message. I drove up there, 100 miles one way, and called it while standing in the room. Got the same message. I picked up the phone, heard a dial tone and dialed my phone and it range through. I hung that phone connected to the device and call it using my cell phone. It rang through. I went home and tried to call it the next day. Again it did not ring through and I got the message after three rings. I call another phone at the facility and had them call me on my mom's phone and it is fixed it again. The fix last for a day or two and then it's broken again, like it is today. If it's a network problem then it must be fairly close to the area because no matter what we do it fails again. So much for the 99.98% reliable. This thing is a piece of junk!
I purchased this device and put it on my plan so that my mother who we placed in a home at 96 years old would have a phone connection that she could use and wouldn't flip her out. My family and her family has not been able to faithfully connect with her at this critical time in her life. I am giving Verizon 10 more days to figure this out and then I am going to ask for a total refund not to mention how much time and travel I have put into this piece of junk. Either the home connect transceiver is broken or the network is broken. Why should I pay close to $70 for a service that has not worked more than several days out of 35 days? Also I have spent close to three hours on the phone with decent technical people, but it's my time. I should send Verizon a bill for every time I have gone up there to fix this device as well.
What perplexes me is that a regular cell phone would have sufficed, but because Verizon has to have a data connection that is not available on a regular phone and it was going to cost me $30/month, I decided to go with the home connect. Seemed like a nice solution for an older person who would have a hard time using a cell phone and keeping it charged. Plus after all the fees for getting it connected, it only cost $20/month. That would be a pretty good thing, IF IT WORKED....... The other thing that irks me is, why do I have to pay for a data connection when the cell phone Verizon originally provided can't even access the network. What ever happened to adding a phone line for $10 bucks\ month? All I wanted was a simple phone. She would not be able to use anything more complex and all she needs is a phone line period.
I have no problem paying for something that works and does what it should, but this is ridiculousness. The MTF on this device is somewhere around 1 to 2 days. Out of 365 days that's about a 96.5% failure rate....... Want my advice? Get ride of this device. It sucks and it's bad marketing.

jsavage9621,
It pains me to hear about your experience with the Home Phone Connect. This device usually works seamlessly and is a great alternative to a landline phone. It sounds like we've done our fair share of work on your account here. I'm going to go ahead and send you a Private Message so that we can access your account and review any open tickets for you. I look forward to speaking with you.
TrevorC_VZW
Follow us on Twitter @VZWSupport

HT5616 I have multiple phones and iPads and all are linked to one iCloud account and one iTunes Account. I want to keep the same iTunes Account so I can share music, etc., however, I want each device to have its own iCloud account. How do I do this?

I have multiple phones and iPads and all are linked to one iCloud account and one iTunes Account. I want to keep the same iTunes Account so I can share music, etc., however, I want each device to have its own iCloud account. Any help on how I can I do this?

You'll need to create an Apple ID for each device. Use the new Apple ID for FaceTime, iMessage and iCloud on the device. Use the original Apple ID for Settings>iTunes & App Store.

Multiple phones connected???

Similar Messages

Maybe you are looking for