Multiple range expanders in hardwired house

I'm trying to set up a single wifi network in a three story, huge, brick house in downtown Baltimore and can't figure out the best way to do it. I currently have the modem on the first floor and going into an older G router, from there it gives a wifi connection to the first floor and a hard wire connection to all the places we need on all floors. Unfortunately we also can't connect to the wifi on the second and third floor. We are looking for the simplest way to add wifi on the two upper floors. We tried using the wired connection upstairs and a second router but couldn't figure out how to do it. Now we realize we probably need two expanders, repeaters or similar products.
Any help would be greatly appreciated.

If you have two Range Expanders so what is the model number of those Range Expander.... Well you have a G - router but what is the model number of that G-Router...
If you have any wired computer, check the IP address that you are getting on the computer from the Router?

Similar Messages

Multiple range expanders

I have a large set up with 5 access points in a warehouse. There are a few dead spots that I am trying cover up. Though these trouble spots are not completely dead zones, I am trying to get better coverage. Can I use multiple range expanders (WRE54g)? I have read posts saying that multiple range expanders is bad, but can I use them if they each access a different access point? If this is ok, how can I tell which range expander is accessing which access point?

If you use the auto config button you must be close to the access point which you are expanding or if the access points are close together turn off the ones that you are not expanding before pressing the auto config button then after it's setup turn on all of the access points.

How can I send data from multiple range with VBA API ?

hello everyone,
i have one worksheet , multiple range. With addin , we can specified the range to retrieve or submit.
In smart view for retreive, I have the API retrieverange so I can do the same. But for submitting data, I only have the API "HypSubmitData" and it doesn't take any paramater like a rangebut only the sheet !
So how do you manager to do it ? one worksheet per range ?
thanks for answers

11.1.2.5.400 added the capability to perform range submission, however I doubt that the vba is not updated with the function. So you might have to wait for a while, or you can create a code which copied the selected cells to a hidden worksheet and perform submit from that sheet. Keep in mind that when the use make the selection, you'll have to copy the pov too.
Regards
Celvin Kattookaran

Error check for multiple ranges input

Hi,
I have coded a report with the following select options:
SELECT-OPTIONS:
   S_PONUM FOR EKKO-EBELN NO INTERVALS,
   S_PODAT FOR EKKO-BEDAT NO-EXTENSION,
   S_LCNUM FOR EIKP-VORNU NO-EXTENSION NO INTERVALS,
   S_VENDR FOR EKKO-LIFNR NO-EXTENSION NO INTERVALS.
I want that a check should be applied at the selection screen level that at least one field should contain a value, i.e. report cannot be run with all blank selection fields.
I am using this code:
AT SELECTION-SCREEN.
IF S_PONUM-LOW IS INITIAL AND
    S_PODAT-LOW IS INITIAL AND
    S_LCNUM-LOW IS INITIAL AND
    S_VENDR-LOW IS INITIAL.
    MESSAGE I007(ZSH_MSGC) WITH 'All selection fields cannot be blank'.
ENDIF.
This works fine, but the problem is that when entering multiple ranges for S_PONUM, when the button on the right of the field is clicked to input range values the message pops up. I want that the check should be applied on execute (F8). Any suggestions? Help is appreciated.
Regards,

Hello,
check the sy-ucomm when the button on the right of the field is clicked keep the condition which i have kept it.
before the if statement keep this condition also
SELECT-OPTIONS:
S_PONUM FOR EKKO-EBELN NO INTERVALS,
S_PODAT FOR EKKO-BEDAT NO-EXTENSION,
S_LCNUM FOR EIKP-VORNU NO-EXTENSION NO INTERVALS,
S_VENDR FOR EKKO-LIFNR NO-EXTENSION NO INTERVALS.
AT SELECTION-SCREEN.
if sy-ucomm ne 'find the sy-ucomm'.
IF S_PONUM-LOW IS INITIAL AND
S_PODAT-LOW IS INITIAL AND
S_LCNUM-LOW IS INITIAL AND
S_VENDR-LOW IS INITIAL.
MESSAGE 'All selection fields cannot be blank' type 'E'.
ENDIF.
endif.
Edited by: Santosh Marupally on Apr 22, 2009 9:41 AM

Have added 3 range expanders to my home network now i find airport express will stream to my hifi but it stops every now and then as though it is buffering, any suggestions?

Have added 3 range expanders to my home network now i find airport express will stream to my hifi but it stops every now and then as though it is buffering, any suggestions?

Have added 3 range expanders to my home network now i find airport express will stream to my hifi but it stops every now and then as though it is buffering, any suggestions?

Multiple Range Selection for field Material in CS14

Hi friends ,
Is it possible to make multiple range selection for material field in tcode CS14 [used to compare primary and secondary BOM] i have made it ZCS14.
if i make matnr2 to matnr2-low
but my doubt is it feasible solution
please through some light on this
regards
soorya

Dear Soorya,
What's your requirement? is that to compare the Alternative BOM's for multiple materials at the same time?
If it's going to be for comparing one more alternative for the same material,then it's a good report.
As per to my knowledge if the report is going to be for a list of materials Alternative BOM's means I dont
think whether it will be a fast(time wise) report.
Check & revert back.
Regards
Mangalraj.S

There are multiple MAC's in my house and I am considering buying Time Capsule to use as a file sharing device. Is anyone doing this? Pros/Cons?

I have multiple MAC's in my house. I would like to create a file server environmet. I am considering using Time Capsule. Is anyone doing this? Pros/Cons?

The Linksys should be about as fast as the Time Capsule. So you might as well connect the Time Capsule to the Linksys, disable sharing and wireless.
Solution two is to use the TC as the router, wireless and network drive. This would save the power the Linksys needs. What is the Linksys connected to? a separate modem?

Reg: Multiple Ranges for Variables

Hello Gurus,
We have a requirement to have Multiple Ranges for Variables and I have gone through the document below which is applicable to 2004s SP 07.
We are on CE 7.1 SP 3 I was looking for a similar document which can guide me to create Multiple Value ranges in CE.
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/07134c67-0b01-0010-0493-b89287cf330f?quicklink=index&overridelayout=true
If this is not available in SP 3 is there a Workaround to have the same kind of functionality.
Thanks & Regards,
Pramod

Hi Pramod,
If I understand correctly, u want to send a range of values to the variable of a query.
This can be done using " ; ". syntax is [value 1];[value 2];[value 3]
If you want to send two dates to a query date variable... take two date fields then pass to the variable date1;date2 (while creating query you took variable of type range)
Thanks,
Pradeep

Question about piggybacking range expanders

I am curious if this would work...
Point A- Linksys Wireless G router
Point B- Linksys Range Expander
Point C-Linksys Range Expander
Point D- Linksys Range Expander
Let's envsion that points A, B, C, and D are on a straight line. They are far enough away in distance that point C couldn't reach point A without point B, etc.
Can I actually piggyback range expanders on each other in order to get back to the router?
Hope that made sense.... thanks so much for your help!
Message Edited by asneed on 03-12-200712:31 PM

Here is an example of what would if you did this:
Point A- Linksys Wireless G router
Speed 54 mbps
Point B- Linksys Range Expander
speed 26 +/- mbps
Point C-Linksys Range Expander
speed 12 +/- mbps
Point D- Linksys Range Expander
speed 6 +/- mbps
Like the post prior to me, use AP through your wireless network.
How much area are you trying to cover?

Two Range Expanders - How to enable security?

I have a linksys router (wrt54g ver 2) and two WRE54G range expanders both version 3. Everything is working fine but I can't enable security because I can't access the set up webpage of one of the expanders. Any ideas? Or maybe I can use Mac Filtering but would I use the mac address of the expanders or the wireless computers? Or any other way to make my little network secure?
I have Windows XP and broadband.
Thanks.

First of all you need to setup your router, and get your wireless computers working. Then later, we can work on the range expanders.
To setup WEP security, do the following:
Turn off all your computers, except for one computer that it wired to the WRT54G.
Make sure the computer is wired to one of the numbered ports on the WRT54G, not the Internet port. Also, make sure the wireless card in the computer is turned off.
In the computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1
Enter your user name (if any) and password.
This will take you to the router's setup pages.
Go to the "Wireless" tab, "Basic Wireless Settings" subtab.
Change your SSID to a unique name. Do not use "linksys". This is the name of your wireless network, and eventually, you will need to enter it into all your network devices (computers, router, expanders, etc.).
Set "SSID Broadcast" to "enabled".
Write down the "Wireless channel" that you are using, and save the paper.
Click on the "Save Settings" button, then wait (3-60 seconds) for the screen to refresh.
Next go to the "Wireless MAC filter" subtab.
Set the "Wireless MAC filter" to "disabled" for now. (If you want to use this feature, we will need to come back later to set it up).
If you changed anything on this page, click the "Save Setting" button, and again wait for a screen refresh.
Next go to the "Security" tab, "Wireless Security" subtab.
Set the "Security Mode" to "WEP".
Click the "Save Settings" button, and again wait for a screen refresh. (Note: the "Save Settings" might not work until you do the rest of the stuff in this paragraph.)
Set the "Default Transmit Key" to "1".
Set the WEP encryption to "64bit 10 hex digits"
Insert your passphrase of 8 to 16 characters (no spaces), then click the "Generate" button.
Copy down "key 1" (it should be 10 hex digits) on a piece of paper and save it.
Click on the "Save Settings" button, and again wait for a refresh.
Exit your browser.
Power cycle your modem, router, and computer.
Login to your router again. Now verify that all of the above settings are still present in the router. If not, put them in again, and be sure to click on the "Save Settings" button on each page that you update. After you have your router setup correctly, disconnect the wire between your computer and router, then power cycle your entire system again.
Now, you must setup your computer for wireless. This setup varies from system to system. So you may have to try a few things to get it to work.
First, in the computer, temporarily turn off your software firewall.
Next, turn on your wireless card and try to display the available networks in your area. Look for the network with your SSID. If you see it, the display will probably also say "encrypted" or "WEP". Click on your network, then click on "Connect". The computer will then ask for your password. At this point, enter your 10 hex digit WEP "key 1", not your WEP password or passphrase. It should then connect. If it does connect, verify that you have a properly working wireless Internet connection.
If it does not connect, then go to your wireless settings and look for something called "Preferred Networks" or "Profiles". In this area, you will be able to enter the info on your network (SSID, WEP, and your "key 1" ). Also, setup your network as your default network, with automatic login. You may need to right click on your network and set this up in "Properties" or perhaps in "settings". Also, while you are here, delete any networks named "linksys", and also delete any other network that you do not recognize, or that you no longer use.
Once you get one computer working, then setup your other computers for wireless. Get all your wireless computers working properly first, and verify that they have a properly working wireless Internet connection.
When you have this done, let me know, then we can setup the range expanders.
But you must have a properly working wireless system before you can expand the range.
Message Edited by toomanydonuts on 08-13-2007 06:30 PM

Disable multiple range dates in datechooser/datefield

Hello guys.
im wondering if anyone ever came across this problem i know the datechooser/datefield component has the disableRanges method which allows you to bascically send in array with start and end date and disable those days. That works great but what if i want to disable multiple ranges.
has anyone ever come accross this problem.
i have a field like so
<mx:DateField x="101" y="6" id="startDateInput" change="datefield2_changeHandler(event)"/>
and in actions ript i do something like this.
startDateInput.disabledRanges = ([new Date(),{rangeStart: new Date(startDateInput.selectedDate.fullYear,startDateInput.selectedDate.month,startDateInput.selectedDate.date), rangeEnd: new Date(endDateInput.selectedDate.fullYear, endDateInput.selectedDate.month, endDateInput.selectedDate.date)}]);
So i have try adding more rangeStart and more rangeEnd to disable more days but nothing works???
any ideas I could really use some help?
thanks in advance
Miguel

thats correct so say i would like to disable
5-10
and
20-25
and leave the rest still light up.
Do you have a small example you can share. I would be forever greatful. I've been knocking my head on this for a few days now. I even consider building a custom calendar.
really appreciate the response.
Miguel

Using countif for multiple ranges

I have a spreadsheet where I need to count a value in several ranges in the same column. Can't figure out how to do it

You can't have non-contiguous ranges but the range can include blank rows. I mention that second part because I don't know what is between your ranges.
You either need to use multiple COUNTIF functions or duplicate the data in another spot (such as another table) where you can make it all one big range (with or without blank rows). The table will simply be a bunch of formulas like =Table 1:: B2

Can you sent music from itunes to multiple ATV2 devices throughout the house at once?

I have multiple Apple TV2's throughout the house and at times I want to play music from itunes and send to all devices can you do that?

Each device is like a separate radio or TV. Select the music you want to listen to from each device. This can be th same album, song, playlist, etc. or completely different selections.

Query to select values that match multiple ranges

Hi,
Oracle 10g.
I have a table POINTS(ID INTEGER, CLASS VARCHAR2(15), CUMUL NUMBER(2,1), ...).
In my application (APEX application), I show a list of point classes, order by cumul.
SELECT CLASS FROM POINTS ORDER BY CUMUL;Then user can choose some range of point classes (CUMUL is not shown in the application, it is just for the example) :
CUMUL     CLASS
12.2     31458     <-
13.4     5S84     <-     range 1
13.6     78PPH     <-
15.0     3R594     <-
15.1     ZB452
15.5     54IO
17.6     21GFD
19.2     A54VV     <-
19.9     IC112     <-     range 2
20.8     158RC9     <-
21.3     G4G5
23.0     V22     <-     range 3For each range, I store only first and last classes selected by a user, in a table USER_SELECTION(ID, ID_USER, FROM_CLASS, TO_CLASS), so using the example above it would give :
ID     ID_USER          FROM_CLASS     TO_CLASS
1     12          31458          3R594
2     12          A54VV          158RC9
3     12          V22          V22
...     ...          ...          ...The problem is that in a query, I need to return all points selected by a user, and I really don't know how to achieve that without too much work... :
SELECT *
FROM POINTS
WHERE USER_ID=12
AND CLASS IN ( *???* );
Any help would be much appreciated.
Yann.

It's not exactly clear what data is in what tables etc. but perhaps something like this...
select user_selection.id, points.*
from points, user_selection
where user_selection.user_id = 12
and   points.cumul between
      (select cumul from points where class = user_selection.class1)
      and
      (select cumul from points where class = user_selection.class2)
order by user_select.id, points.cumul

Using the same stb settings on multiple stb in the same house

I have set up my main stb the way I like it with favorites, parental controls, etc. is there a way to "push" this stb settings to all the other stb in my house?

No there is not. You most configure each STB individually.

Multiple range expanders in hardwired house

Similar Messages

Maybe you are looking for