Multiple Router Setup, how??

As above,
Having some issues getting AppleTV (and my iPhone (Remote app) to read my computer upstairs which has iTunes on it.
The setup is:
AppleTV plugged into ethernet port of HomeHub(ADSL Hub) downstairs
iTunes computer plugged into a Netgear router upstairs which is plugged into an ethernet port of the HomeHub.
Now when i'm in AppleTV I choose Manual config, what IP's/Subnets/DNS's etc do I need to put in to get this thing working?
If I try it in my room it all works perfectly as its on the same network, but not downstairs.

Thanks for the help.
I did this but it killed the wireless function on my router upstairs, so the current setup i have is
Port 1 is internet in, bridge to port 2 (the PC with iTunes) and to resolve the wireless issue i have bridge internet in to port 3, now i have wireless and have the netgear setup as a bridge, however, before i bridge port 3 it worked perfectly downstairs, now I cant browse Remote app is working too...

Similar Messages

Can't connect to router setup page

Hi,
I have a WRT54G wireless router, version 2.1. It's been working fine for the last 3 years and suddenly the WLAN light is out and there's no communication between router & computer. I've tried resetting it (via reset button, and unplugging power) a million times with no results. A techie thought maybe I needed a firmware upgrade -- which I've downloaded, but now I still have to access the setup page to install it, which seems to be impossible. The 192.168.1.1 page won't come up at all. (And when I went into the command prompt, it said my Default Gateway was 207.237.223.1 -- which, of course, I've tried, but that won't come up either.) I've turned off firewalls and antivirus programs, thinking they might be the problem -- still nothing. Any suggestions/advice would be MUCH appreciated! Thanks in advance!
TrevorNYC

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

Home Networking and Multiple Router Set up Problem

Router 1 (Main Access Point)
        X
(Routers 1 and 2 connected via a wireless bridge)
Router 2 (Wired Access Point)
    X
(Router 2 and 3 connected via a wired bridge)
Router 3 (Wired & Wireless Access Point)    Note:broadcasting under a different SSID
         X
Problem:
When I set up a wireless and wired bridge my Internet connection works perfectly and I can connect to the second SSID. If, however, I close out of my browsing session and come back to my laptop several hours later and open a browser, I get the “webpage cannot be displayed” message.
I suspect this has to do with IP addresses changing from the main router after a certain amount of time.
What could be causing this?
What can I do to stop this from happening?
Thanks for any help
EML

Running multiple router behind router can be tricky and may be the cause of your dropouts if you don't have it configured properly.
Cisco recommends using your best router as your primary router and DHCP server.
The best way to setup for home networks, in my opinion, is to use only one router, and put the other router(s) in bridge mode. Also, make sure your modem is not a router too.
http://www6.nohold.net/Cisco2/GetArticle.aspx?docid=28cee6a2fb0d4176a2210942d1d5836c_Setting_up_the_...
http://homecommunity.cisco.com/t5/Wireless-Routers/Guest-access-never-displays-password-prompt-on-EA...

E4200 - Okay router, setup issues

I chose this router over the Netgear N750 because of previous bad experience with their customer support and over the Asus RT-N56U b/c of a compatibility issue with a specific application.
The Cisco Connect Software is very poor software. No OSX Lion support so I could not use my Mac for setup and it could not even detect the router on a wired connection on a Windows 7 PC through a simple Dell unmanaged switch. Even the router setup software built into Windows had no problem with that. I had to rely on manual setup which was straightforward.
Range was mostly adequate for me with both 2.4 and 5 Ghz over 5,000 sq. ft. of indoor space with no direct line of sight, through many walls, multiple floors, and the outside patio also, although with a few connected devices I found the 5 Ghz band somewhat unreliable at times. Wired gigabit performance was good enough for my purposes.
Overall a decent router, not bad, not great.

It seems like you are using an outdated version of Cisco Connect Software… There is a new release of the Cisco Connect Software that supports Mac OS X (10.7 "Lion")… So you need to download the latest Cisco Connect from the Cisco Website (homesupport.cisco.com) or you can use this link: http://homesupport.cisco.com/en-us/support/routers/E4200 ... After downloading you need to set the router to factory defaults, power cycle the whole network and then run the Cisco Connect that you downloaded…
For more information about setting up E4200 router with Cisco Connect. Please refer to the link below.
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=22732&userrole=Links...

Multiple Routes Single Delivery

Dear SD Experts,
Leveraging on the org element "Transportation Planning Point" I see a need for multiple routes in the sales order depending on the shipping points from where product is loaded and send to the TPP finally for consolidation (e.g. goods are loaded from more than one plant-warehouses and then sent to a single place for further exports as in common in export scenarios. A delivery and invoice is then created for the whole order
Can someone explain how do I ensure delivery group correlation in in such a case
Regards,
Loknath

Thanks you Chak,
That was indeed reassuring because thats the current state but that complicates the sales order process with having to manage a plant other than delivery plant which is not the port.
Is there any other simpler possibility e.g. of calling it something else other than TPP or logical plant (e.g. Transportation Connection Point) so that it lends itself to both objectives of a more robust route determination while capturing the fact that TCP is a port or a rail siding or a customs border where I can maintain times and calendars for scheduling the loading dates at shipping points (of delivery plant)
I would appreciate SD consultants view on this. I am not from SD scheme of things but am really interested in a route determination logic that I can use for conditional scheduling in APO
Regards,
Loknath

Multiple Monitor Setup for HPE-180t w/ NVIDIA GeForce GT 220 (only one DVI port)

I am wanting to connect mutliple montitors via DVI connection to my HPE-180t. My graphics card is the NVIDIA GeForce GT 220 which has 3 ports (VGA, HDMI, DVI) and does support mutli monitor display. What is the best way for me to connect multiple monitors to my desktop? I would like for all of them to be connected via DVI.
Thank you so much,
Angela
``````````````````````````````````````````
old computer: HP Pavilion PU131AV / a1050y, Windows XP MCE, SP3 32bit, Nvidia GeForce 6600, Intel Pentium 4 CPU, 3.20 GHz, 2GB of RAM
new computer: HPE-180t, Windows 7 Pro (64bit), Nvidia GeForce GT 220, Intel Core i7-930 quad-core CPU @ 2.80 GHz, 8GB of RAM

What is the end goal you are attempting to acheive? Are you looking to clone all three monitors or each monitor to be independent of the other (extended display)?
This document covers how to configure the monitors in Windows 7. I didn't see the GT 220 listed in the specifications, so I take it this is one purchased separately for the unit. Most video cards require multiple monitors to be connected to a different port (to truly achieve a multiple monitor setup). Since the card only has one DVI port, then the other ports (HDMI and VGA will need DVI adapters). An example of an HDMI - DVI adapter can be found here.
The tricky part will be using the VGA - DVI adapter as DVI ports are typically DVI-D which makes it a pure digital signal. VGA is analog, so the adapter will need to be special if the monitor is using a DVI-D port. If it is a DVI-A or DVI-I port, then a standard VGA - DVI adapter will work. If it is a DVI-D port, you will need an active VGA - DVI adapter. If it is DVI-A/I, then a passive adapter will work. This is an example of an Active VGA - DVI adapter. For that adapter, a VGA cable will need to be connected to the VGA port with that end connected to the VGA side of the adapter and then being connected to the DVI port of the monitor.
Provided the video card supports 3 monitors, this would allow all monitors to have a DVI connection. Keep in mind that the VGA port will still deliver an analog signal as opposed to the DVI and HDMI ports. The card specifications do not really say how many monitors it supports, but it most likely does support three monitors.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Disable BFD in multiple Router Sub interfaces that participates in OSPF

Hi team,
Please help me on this. Here is the scenario:
We are on an enterprise set up and running on 100+ routers.
We have 200 to 300+ sub interfaces for virtual circuits
Our protocol is OSPF over MPLS
One of our provider in LA encountered link flaps on SONET causing our LA router that is directly connected to that link to recalculate multiple times.
Recalculation of OSPF routes caused disconnection of users in LA VM's.
We were advised by our provider in LA to disable BFD so minor link flaps will no affect recalculation of routes.
We are now tasked by our design team to Disable BFD in multiple Router Sub interfaces that participates in OSPF.
My questions are:
What is the implication in disabling all BFD in routers' interface and sub interface?
Will this improve recalculation of OSPF routes in cause of link flaps or it will totally ignore the link flaps?
Will the routers only recognize a "full down" status of the interface?
How can we Disable BFD in multiple Router Sub interfaces that participates in OSPF in a faster way? Or do we have to do this one by one?
Please advise before we present this to the CAB and implementation. Thank you.

My questions are:
What is the implication in disabling all BFD in routers' interface and sub interface?
Answer: the implication would be eliminating sub-second millisecond convergence.
BFD detect failure at the link layer very fast , once detected it informs the upper layer protocol about the failure causing it to converge immediately.
Will this improve recalculation of OSPF routes in cause of link flaps or it will totally ignore the link flaps?
Answer: if your Provider experiencing intermittent flaps, then yes it will be advisable to turn BFD off. this however doesn't totally ignore the link flaps, once the upper protocol detect the failure based on the dead interval parameter on OSPF, it will recalculate OSPF routes again. Keep in mind, if you have redundant or more links to your provider , then I wouldn't recommend disabling BFD , as it should improve Convergence and you shouldn't notice the failure.
Will the routers only recognize a "full down" status of the interface?
Answer: disabling BFD allows the router recognize a full down status once the upper protocol dead interval occurs or full down status of interface. which ever occurs the earliest.
How can we Disable BFD in multiple Router Sub interfaces that participates in OSPF in a faster way? Or do we have to do this one by one?
You can disable it one by one. or if you have configuration management software, it allows you to do it for all nodes at a time. but this depends if you have it or not.
Please consider not to disable BFD if you have multiple OSPF links towards your provider from any branch, as it shouldn't impact your VMs, it should rather improve Convergence at milliseconds which is absolutely not noticeable.
BR,
Mohamed

HT4995 My iPad 2 Location Service works fine but does not work on my home Airport router. How can I fix the problem?

My iPad 2 Location Service works fine but does not work on my home Airport router. How can I fix the problem?

lbryan1987 wrote:
I dont want the button problem solved i need to know how to restore the phone without using that button or going into settings
You don't in the condition it's in. You will either have to get the phone replaced by Apple or pay a 3rd party to repair it.
there seriously should be more than two ways to solve this other wise apple is useless and we will never buy another apple product.
Seriously? It's physically broken!

Hi, I activated my CS6 in 2012 under my student licence and still using it. I've heard that you can't run CS6 on multiple computers. How do I transfer it from one computer to another as I am switching computers?

Hi, I activated my CS6 in 2012 under my student licence and still using it. I've heard that you can't run CS6 on multiple computers. How do I transfer it from one computer to another as I am switching computers?

Hi,
first, I'm not Adobe's "slave" as you might to accuse me. Most of the posters here are users like me.
I only can repeat that what I found in Adobe's help sites, as I wrote above. You are free to figure out the "real" truth and - the best would be - you may contact Adobe directly, here are - I'm sure you know them - the links I would use: http://helpx.adobe.com/support.html and http://helpx.adobe.com/contact.html.
Hans-Günter

Multiple desktops and how do I remove them?

How do I even end up with multiple desktops and how do I remove them. All gets very confusing!
Thank you

Swipe up with 4 fingers, or press F3 (or fn+F3 depending on how you have your keyboard configured)
At the top of your screen should be all your desktops simply hover your mouse around the top left area of one of them (apart from the first one) and a X will appear which you can click to close it

How can I use a SCH-LC11 device in CHINA which bought from ebay. I am not Verizon customer but I prefer to using your 4G LTE Router . How can I get the unlock code? The device may have a bad ESN but I only use it in CHINA. Kindly looking forward your repl

How can I use a SCH-LC11 device in CHINA which bought from ebay. I am not Verizon customer but I prefer to using your 4G LTE Router . How can I get the unlock code? The device may have a bad ESN but I only use it in CHINA. Kindly looking forward your reply. Thanks!

It's good to read Antoniad's post. It reassures me that I can use my new iPad as an international communication device which is the reason I purchased the thing. However, I called Verizon today (my provider of cellular data) who told me that I can't just pop in a SIM card as you suggested. He also said that he was from the "Pre-Pay" division of Verizon and he was certain that I couldn't do what I planned to do. I was extremely disappointed as I had called Apple prior to buying the iPad and I read the algorhythm on the website for choosing an iPad before purchasing. Those sources were quite specific and the information seemed clear. I would be able to use my iPad to communicate through cellular connections while traveling on the road, literally, abroad. I was told that I could pop in a data card wherever I was, just as you indicated in your message above, and voila I was good to go. The Verizon rep definitively rained on that parade, but said that I might be able to do this if I have a "Post-Pay" account, a different area of Verizon. I haven't had the chance to talk to this division yet, so I looked to Apple's Support for answers. Maybe I will find out that I can use my iPad as an international communication device while traveling on the road afterall, however, it appears I may need a different type of account (Post-Pay), something I was never warned about. Can I switch to this kind of account? I don't know. I have to find out. If you have any information about this issue, it would be good to share since I strongly suspect there are others who bought the iPad for the same purpose that I have.

I just bought a new iMac and I am using a apple air port router. How do I connect mt windows PC to the air port router do I can move files

I Just purchased a 21.5 iMac and connected it to the Internet using a apple air port router. How do I connect my windows PC to my air port router so I can transfer files.

It makes life easier to install the airport utility for windows.. which has a couple of different apps in it.. if you airport is new type then the utility is too old.. but is still valuable for Bonjour which provides network information for shared devices in the apple world to windows.. and a disk access agent..
It will also help the Apple computer access shared directory in the windows computer.. nowadays this is pretty easy.

I need to back up my imac running Tiger (no time machine) so that we can upgrade OS. It is set up for multiple accounts. How do I capture all files in each account using newly purchased USB external hard drive?

I need to back up my imac running Tiger (no time machine) so that we can upgrade OS. It is set up for multiple accounts. How do I capture all files in each account using newly purchased USB external hard drive? Thanks!

Backup Software Recommendations
Carbon Copy Cloner
Data Backup
Deja Vu
SuperDuper!
Synk Pro
Tri-Backup
Others may be found at VersionTracker or MacUpdate.
Visit The XLab FAQs and read the FAQ on backup and restore. Also read How to Back Up and Restore Your Files.
Or you can simply use the Restore option of Disk Utility to clone the drive to the backup:
Clone using Restore Option of Disk Utility
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.

I recorded VCR tape onto DVD-R but will not play on my MacBook Pro. I have already recorded multiple DVDs. How can I get it to play on my Mac?

I recorded VCR tape onto DVD-R but will not play on my MacBook Pro. I have already recorded multiple DVDs. How can I get it to play on my Mac?

"I recorded VCR tape onto DVD-R"
How? Using what equipment/software?
"The DVD plays on the device on which it was recorded."
Just a guess: You're using a VCR-DVD combo recorder. DVDs produced in this way will play on the device that made them, but won't play on anything else until they're "finalized." In fact, Macs will recognize unfinalized DVDs as blank discs until the discs are finalized. Check the manual that came with the recording device for instructions.

Multiple routing tables and/or policy routing

Hey all,
I'm trying to configure a Mac Mini (10.8) for multiple routing tables and policy routing. This server runs Ostinato, a freeware traffic generator. My purpose is to generate traffic on multiple VLANs towards different gateways and different destinations. To that end, I have VLAN tagged the (only) Ethernet port and configured 5 VLANs on it. The first one has the default route (I manage this Mac over this VLAN). The other four have IP addresses in the test range I'm using.
The goal is to have traffic sourced from IP-address-X go out vlanX towards gateway-X. It's counterpart on the far end runs Linux and I have configured it in this way:
ip route add default via <gateway-X> dev ethX table X
ip rule add from <network-X> table X priority X
Researching on OpenBSD forums (since it's the base of MacOS X), provided this:
route -T X add 0.0.0.0/0 -iface <gateway-X>
echo pass in from <network-X> to 0.0.0.0/0 rtable X | pfctl -mf -
However, the Mountain Lion "route" command does not support the -T option, so that killed that idea. Another forum suggested that this would have worked on 10.4:
ipfw add X fwd <gateway-X> ip from <IP-address-X> to any
I tried this on 10.8 though the man page says it's deprecated, and (surprise, surprise) it did not work.
Any ideas to get this working appreciated!
Thanks,
Aaron

Still doesn't have it in 10.9.4.
irene:~ cschwartz$ sudo bash
bash-3.2# route -T add
route: illegal option -- T
usage: route [-dnqtv] command [[modifiers] args]
I'm guessing you want policy-based routing due to VLANs...? If you can get a USB-to-Ethernet adapter, then maybe you can work around this by using multiple physical links instead of VLAN tagging. But if you need source-based routing etc. then no.

Multiple Router Setup, how??

Similar Messages

Maybe you are looking for