Multiple SSID channel question
I have 2 (for now) Aironet 1231g access points setup. They each have two SSIDs being broadcast on each one, both are the same two SSIDs. The question is, can can two different ssids from a single ap broadcast on the same channel. That means I would have both ssids broadcast on channel 6 on one of the APs then broadcast them both on channel 11 on the other? Or would each individual ssid have to be on its own non-overlapping channel? Both SSIDs are on seperate vlans. As of now it looks like it is working fine, I just want to make sure I have it configured the way it should be to work the best.
Hi Chris.
Channels are by radio, not SSID.
Exmaple
(AP#1) Channel 1
SSID - TEST1
SSID - TEST2
(AP#2) Channel 11
SSID - TEST1
SSID - TEST2
As you can see your TEST 1 will broacast on channel 1 and 11 ...
Make sense?
Similar Messages
-
Single access point with multiple ssids and single channel possible?
Hi everybody.
I have this silly question.
Let say we have three vlans, vlan1,2,3 and they are mapped to wlans as follows:
Vlan 1 ssid1
Vlan 2 ssid2
Vlan3 ssid 3
AP --------trunk------Switchted network.
Our Ap has mobile devices in three wlans, i.e ssid1ssid2 and ssid3
Since AP uses half duplex mode, mobile devices need positive ack from ap before they can send data, therefore once channel let say channel 3( assuming 802.11b is used) can be shared by all mobile devices in three wlans.
Is my understanding correct?
Thanks and have a great weekend.Hii ,
Yes ,that is pretty much possible as suggested by other experts on board. Depending on your access point you will have 1 (2.4 GHz) or both 2.4 & 5GHz radios.
You can configure multiple SSIDs (up to 16 ) known as MBSSID mode in autonomous environment. In Controller based architecture you can configure up to 512 WLAN (SSID) and transmit any 16 of them per AP (using AP group feature). However , it is recommended to keep multiple SSID count below 8 as for each SSID separate beacon will be sent on air which consumes more air time.
Hope this helps
Thanks
Vinay -
Multiple SSID with different Login Web authority pages
Our current setup is one Anchor control and then several WLC’s, I want to know if I can have multiple SSID and use different Web Auth pages form them, so I can have a SSID that requires a password to Authentication access and another SSID that requires pass through Authentication but they would have different web authentication pages and go to different pages once Authenticated.
Is this possible to ?Hi,
If you are running WLC software 4.2 and above then u can do this on per WLAN basis.. here is the link which tells on how to do it..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml#A1
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra -
Is it possible to do multiple ssids and encryptions on an autonomous AP without vlans?
I got a customer who just has autonomous APs. They are upgrading from 1210s to 1262s. They are currently running a config that is wide open with no authentication or encryption and using a VPN tunnel on the wireless clients for security. They want to switch to using WPA2/PSK with the new APs. They have existing clients that have to continue to work during the upgrade to the new APs. They run 3 shifts so it is a 24 hr operation with no downtime. What I was thinking would be to configure the 1262 with multiple SSIDs, one with their existing settings and one with the new. Then I could swap the APs one at a time and it would only impact service for a short period of time while I was mounting the new AP. Then once all the new APs are installed I could transition the clients over to the new SSID and encryption then disable the old SSID once all the clients are switched over. I've done this before with a WLC but not with an autonomous APs. The only config examples I can find uses VLANs. This customer is not using VLANs. Is there anyway to use multiple SSIDs with different encryption on a single radio on an autonomous 1262 without VLANs?
The site has about 30 APs and 100 clients. Yes I know a controller would be preferred for a site of this size but that is a question for sales and why they didn't see them a controller. I just get stuck with what they sell them.
thanksHi Don,
Im afraid on the autonmous platform you can not map multiple WLANS to a single vlan.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
Using multiple SSID with AP 1100 (standalone mode).
Hi, need to configure 2 SSID on the same 1100 AP: open authentication and WPA2. It's possible to configure these 2 SSID without configuring VLAN's ?
On CCO I've read the following:
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a008009483e.shtml
Q. How many service set identifiers (SSIDs) can you have per VLAN?
A. You can have only one SSID per VLAN. The use of multiple SSIDs over a single VLAN is not supported with Aironet APs.
It's also true with the latest IOS release ?Hi Roberto,
Hopefully the attached docs will answer your question:
Cisco Aironet 1100 Series
Using VLANs with Cisco Aironet Wireless Equipment
Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 12.2(15)JA
Configuring Multiple SSIDs
vlan vlan-id
(Optional) Assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. You can assign only one SSID to a VLAN.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
Hope this helps!
Rob
Please remember to rate helpful posts....... -
Hello,
I am attempting to set up three Cisco 1242AG Wireless Access Points with multiple SSID's. I used the web interface and directions online to set up the two networks I want and at least one of the networks work wirelessly.
However, I have two problems:
The first, which is the most important, is that the "management" interface, BVI1, doesn't get an ip address from our DHCP server. I set the VLAN 60 (which you'll see in the documenation below) to be the native VLAN on the device as well as on the switch that the device is connected to as well as other settings in the configeration file below. Because of this, I can only manage the device via the console port which would be a huge pain once all of the devices are mounted.
The second problem is that I am not sure how to get both wireless networks broadcasting their SSID's. I have to manually type in the SSID for the second wireless network I have which I would prefer I don't have to. Anyway I can enable broadcasting on all of the SSID's?
Thank you for your time.
Regards,
Christopher Koeber
Using 7916 out of 32768 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-18.wesleysem.edu
enable secret {Number Here} {Encrypted Password Here}
enable password {Number Here} {Encrypted Password Here}
aaa new-model
aaa session-id common
dot11 syslog
dot11 vlan-name Kresge vlan 20
dot11 vlan-name Library vlan 30
dot11 vlan-name Public vlan 60
dot11 vlan-name Secure_Public vlan 70
dot11 vlan-name Secure_Seminary vlan 80
dot11 vlan-name Server_Room vlan 1
dot11 vlan-name Straughn vlan 40
dot11 vlan-name Trott vlan 10
dot11 vlan-name Web_Room vlan 50
dot11 ssid (Secure) Wesley Campus
vlan 80
authentication open
authentication key-management wpa version 2
wpa-psk ascii {Number Here} {WPA Key Here}
dot11 ssid Public
vlan 60
authentication open
mobility network-id 60
username Cisco password {Number Here} {Encrypted Password Here}
username admin privilege 15 secret {Number Here} {Encrypted Password Here}!
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 80 mode ciphers aes-ccm
ssid (Secure) Campus
ssid Public
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption vlan 80 mode ciphers aes-ccm
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio1.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio1.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface FastEthernet0
ip dhcp client update dns
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface FastEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
no bridge-group 30 source-learning
bridge-group 30 spanning-disabled
interface FastEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
no bridge-group 40 source-learning
bridge-group 40 spanning-disabled
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
no bridge-group 80 source-learning
bridge-group 80 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
endI am using a third party DHCP server which is our Windows Domain Controller. I have the ip helper-address set for the native vlan of the Access Point through a layer 3 distribution switch (a Catalyst 4506) that the current switch connects to.
I didn't see any event on the logs for the AP.
Let me know if I need to do something else.
Thanks. -
Multiple SSIDS and disappearing
We have Cisco 3602i access points for the most part, all of which advertise multiple SSIDs.
Very occasionally we see an SSID completely disappear from view, even though others remain solid (I can't say it's all devices as the majority of people who raise the issue have apple devices, but there are the odd one or two who use Windows laptops).
Also, the RSSI seems to fluctuate wildly.
I should add that we have disabled up to 11mbps data rates on the controller and we're running 7.6.100.0 currently, but plan to upgrade to 7.6.110.0 tonight.
I guess my question is how can an SSID just drop off the client view if others on the same AP are fine?
How does the AP deal with multiple SSIDs and does it prioritise?
I have to add that I've never had this issue and I'm just using a company standard HP laptop with an Intel chipset.Hello,
See my comments:
Also, the RSSI seems to fluctuate wildly.
A: This is often how a device hears the frames. Sometimes in high interference you can epxect this to jump around. I normally like to see if all the devices are doing this or just a select few. Sometimes poor clients jump around more than others.
I should add that we have disabled up to 11mbps data rates on the controller and we're running 7.6.100.0 currently, but plan to upgrade to 7.6.110.0 tonight.
A: I dont think turning off lower rates are bad unless your WiFi cant support the design. Good call get on the latest.
I guess my question is how can an SSID just drop off the client view if others on the same AP are fine?
A: Again, its a client missing frames like beacons.
How does the AP deal with multiple SSIDs and does it prioritise?
A: This SSIDs are virtualized. I blogged how this is done:
http://www.my80211.com/home/2011/5/2/wlc-how-cisco-virtualizes-the-base-radio-mac-address-on-the.html
I have to add that I've never had this issue and I'm just using a company standard HP laptop with an Intel chipset.
A: Again I think if you search you might see this is more around specific devices. I would do a packet capture and see what is going on. Recently had to troubleshoot an Android only to find out it was just bad wifi client. Always sending NULL frames and scanning and not passing traffic -
Wireless Network Management with Multiple SSIDs in one Wireless Profile
Could anybody explain me about how Multiple SSIDs in one Wireless Network Name (Network Profile) ? Configuration will be pushed to Windows 7 Pro from Wins Server 2008 R2.
Objective: Multiple office locations will have different SSIDs and when the laptop user travels one location to another, he/she could connect to wireless networks at any offices without any configuration change but utilizing "Automatically use my Windows
logon name and password (and domain if any.)" setting in EAP MSCHAPv2 properties.
Network Name: Enterprise
SSIDS: SFO-WIFI, LAX-WIFI,CHI-WIFI,NYC-WIFI,
Network Type:Access Point
Security Type: WPA2-Enterprise
Encryption Type: AES
Network Authentication Method: Microsoft:Protect EAP(PEAP)
My question is: (1) Will Windows try all the SSIDs in order to get connected to the Wireless Network at the office? (Let's say, user is in NYC, but will Windows try to find SFO-WIFI SSID first, wait until time out, retry?, and moves on to LAS-WIFI SSID,
wait until time out, retry?, and moves on to CHI-WIFI and finally tries NYC-WIFI SSID and found the SSID in the beacon from Access Point and authenticates through RADIUS?
(2) If the answer is YES, what is the waiting time/timeout setting for one SSID before moves on to another?
(3) If the answer is NO, what is the process to get user connected to NYC-WIFI SSID when he/she is in NYC office within the range of that SSID?Hello Ninjago_2224,
About the multiple office location have different SSIDs, does the location A has the signal used in
location D?
Please go to Control Panel\Network and Internet\Network and Sharing Center
, and then click Manage wireless networks.
The windows will try to connect to these networks in the order listed.
Please check if the four SSID pushed by Windows Server 2008 is listed as mentioned above.
If the location A have the location D SSID and the location D SSID has higher priority, the Windows will connect to
location D SSID.
So about the question 1, the Windows will try the SSID in order.
About the question 2, I can’t find the accurate time that test one SSID and move to another. But based on my test, it is very fast.
For more information, please take a look at the following article.
http://www.howtogeek.com/howto/27067/change-wireless-network-priority-to-make-windows-7-choose-the-right-network-first/
Please note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support -
Export MXF with multiple audio channels for broadcast
Hi,
I work at a broadcast company as an editor. We always used FCP with the free sony xdcam plugin to export. This plugin seems to be one of the rare ways to export an MXF with 4 audio channels. I don't know exactly why we need to export it for broadcasting with 4 audio channels, but we do.
Since our workload has grown enormously the last few months and it will only become more we are optimizing our workflow. We also work with a lot of different endboards in After Effects and we made a nice template to work with. And since AE and Premiere can make a dynamic link we are considering changing from FCP to Premiere.
Now comes the question!: The only obstacle we could not find an answer to is exporting it with 4 audio channels as an MXF from Premiere CS5. Will there be some development on this level regarding CS6?
A solution to this should save us a lot of time!
Any help will be highly appreciated!
I also attached an example for the usual MXF files we exportI have the same problem. I have a project with multiple audio channels and I want to export them as individual channels in a MXF-file.
Method:
When I created a new sequence I choose "Multichannel" from the "Tracks" page. When I export the MXF OP1a, I choose 8 channels from the "Audio" page. None of the channels are muted.
Result:
The rendered file contains 8 channels, but only the first two channels contains any audio (main left + right), the rest of the channels are empty. Channel 1 and 2 contains the audio from all channels, but I want the channels to be seperated in the same way as they are layered in Premiere.
I don't understand your answer to wleoni75's question. Could you please help me further? -
How can you create multiple SSIDs dot11radio1 an interface with a separate DHCP pool?
Hi,
Please go through this document which i hav written on Multiple SSIDs on the AP..
https://supportforums.cisco.com/docs/DOC-14496
Lemme know if this answered ur question!!
Regards
Surendra -
NPS, wifi, multiple SSIDs - multiple policies?
We are setting up a new wireless network with multiple SSID's. We plan on having an internal network, a guest network, and a personal devices network. The questions is how do authenticate against multiple policies on the same NPS server? Our current NPS server authenticates against AD group AND AD user account for the internal network. If I want to authenticate the personal devices SSID against the NPS, can I set up a different policy for it only?
My understanding is that when a user/device queaeries the NPS, it goes down the policy until it finds a match and then allows access. Is this true? ThanksThanks,
Basically we want to use NPS to authenticate our wireless users and we also want to use NPS to regulate access into our switches/network devices. If I create a policy for example wireless that says If user is part of domain users, then grant access, how do I Create another policy that regulates who can log into my switches? Since the policy matches, it allows the user to log into the switch. Does this make any sense? Do I need a separate NPS/AAA server to authenticate my cisco switches/routers? THanks -
Multiple SSID's on the same subnet?
Can you have Multiple SSID's on the same subnet?
SSID1 authenticates clients via radius.
Our corporation bought printers with wireless cards that only support WPA-PSK so we created SSID2 for the printers. We can connect to both SSID's and ping from SSID1 to SSID2 but we can not perform other functions such as view the printer management interface with a browser. Should it be possibe to communicate between SSID1 and SSID2 on the same subnet?Yes you should have no issue, but the only thing is that you are using a lower security method... so either you put them on different subnets so you can control the traffic via acl's or might as well use the same security method to make it easier. The fact that you can ping sounds like you should be able to http to the device.
-
I have a 10 question survey that has been running fine and providing accurate responses in reports generated from my LMS. I made a property change to a multiple response type question that is now causing the reports to show a date/time (2003-01-01 18:00:00) response instead of the actual multiple responses the user made. The change I made to the question was to change the "Numbers property from" [ a), b), c) ] to [ 1), 2), 3) ]. This property change did not affect the reported responses for the single response questions, only the multi-response. This problem occured Using Captivate 4. I then tried using the same properties in Captivate 5.5 thinking it was a bug in CP4, but got the same results. Has anyone else run into this issue? I'm going to bring this to the attention of my LMS provider, but want to make sure CP is clean first.
Thanks,
DaveFirst things first. I am not an LMS expert, so this is not about troubleshooting.
However, to ensure that your course works fine on a SCORM-compliant LMS, you can upload it to cloud.scorm.com and test it out. If the course works fine there, rest assured that it will work fine on any SCORM-compliant LMS. If your LMS team comes back with an issue after this, you can counter them with this evidence that the problem is with the LMS and not your course.
Sreekanth -
LSMW datamigration material master with multiple distribution channels
Hi,
We plan on using the LSMW to migrate our customer's material master to a ECC 6.0 system.
Currently we use the BMM00 and BMMH1 structures, but there I can specify only one distribution channel.
Does anyone know how to include multiple distribution channels in LSMW material master migration?
Thanks in advance for your support.
Edited by: Mohammed Qasim Malik on Jan 21, 2008 10:01 AMyou need an extra record in your source per distibution channel.
Alternative you can create the extra record with a small Abap code in LSMW in section __END_OF_RECORD__
There you habe in standard the code:
transfer_record.
just add after this statement a statement that gets the additional wanted distribution channel into the distribution channel field.
BMM00-VTWEG = 'xx'.
transfer_record. -
Knuckleheaded Alpha Channel Question of the Week
OK...I rarely monkey around in Motion, but I have amazingly just created about 10 different animated versions of my client's logo for use in various films (cut in SD in FCP). I need to be able to library these rascals so I can just drop them into FCP when I need them.
However, and here is where the knucklehead deal enters the picture.
I am baffled as to how to export the logos out of Motion so there is no black background! I want to create a QT file of each version that I can library and then import into FCP. I have already checked the all of the Alpha channel questions dealing with this issue and the answers are like me and algebra in the 7th grade...huh?
Can somebody give me the kindergarten version of how to get rid of the black background behind my little purple animated logo.
Thanks in advance and I promise to close Motion and step away from the keyboard as soon as one of you mavens helps me solve my little non power user dilemma.Easiest would be not to export at all, but save a different project file for each version - then just bring the Motion project file into FCP. As long as you have set the background to be transparent (Edit > Project Properties), then the project file will have transparency.
If you want to export, you need to choose a codec that supports an alpha channel, such as Animation or PNG.
Maybe you are looking for
-
How to remove a page from Pages document
I have created a document in pages, and it is 12 pages. This is the complete document, originally created to export as a PDF. I want to create a smaller version of the document, removing certain pages that some people do not need. Unfortunately, I cr
-
Mail rules work for some users, don't work for others
Ready to pull my hair out over this one: Leopard to Snow Leopard upgrade went uneventfully, except for the fact that server-side mail rules (accessed via browser at FQDN -> Mail Rules) work for several users (two, to be exact) and don't for the rest
-
Help with Firefox seperating spacing in words!?
Firefox has spaced letters and words extremely far apart, and to the point where I cannot read it anymore. I have tried uninstalling and reinstalling but this did not work. Take a look at what I mean: Google's "I'm feeling lucky" has a bunch of space
-
I have the adobe photoshop elements 3.0 for windows and am wondering if I can get it replaced for my new mac computer? Otherwise can I get a discount if I purchase a new elements for the mac? Thank yo o much. Lynn Jensen
-
Mac os10.9 and updated after effect cc 12.0.1 still have problem
After Effects warning: Could not rename the file '/Users/xxxx/Library/Preferences/Adobe/After Effects/12.0/Workspaces.1121.1407353248120481.xml' to 'Workspaces.xml'.