Multiple WLANs & DSL connection

Has anyone had any experience with configuring multiple WLANs feeding into a single DSL connection?
I need to set up WLANs in 4 separate rooms that each have single cable back to a switch and a DSL connection.
The idea is that each room will be stand-alone as far as the WLAN is concerned and when they need Internet access they plug into the Ethernet port in the wall which is cabled back to the switch and DSL.
Each room will have a 4-port wireless router with DHCP server configured (the 4-ports are for those without wireless). Initially security won't be an issue but we realise that VLANs will probably be required down the track and a managed level-2 or 3 switch will be required. For now we are happy to just use separate wireless routers with minimum security.
I am assuming something like a WRT54G will do the job but how to configure the WLANs? Different SSIDs and channels? Could we use different networks (eg 192.168.1.x and 10.0.0.x) and then would we need to bridge them etc?
K

Hi .. you can definitely configure the routers in the way you have described. You will have to set up different ssid and channel on each router in each room. Also you have to use different networks.Say eg 192.168.1.1 on the 1st router and 192.168.2.1 on the 2nd router and so on.

Similar Messages

Multiple WLAN connections

Does anyone know of a way to get my PODCAST and Email applications to use multiple WLAN connections?
I spend most of my day in one of two places, each with a different WLAN, and I'd the phone to have the sense to change WLAN connection as they become available.
Thanks for your time.

Depends, on what your phone is.
If you're using an N97 or a 5800, or anything running on s60v5 for that matter, Go to Menu>Settings>Connectivity>Wireless LAN>Options>Settings>Show WLAN availability. Then you can also set how often it will set to scan for WLAN connections. This would allow the phone to scan for WLAN hotspots around you immediately. Be warned however that this will drain your battery faster.
On an s60v3 phone, I am not very familiar but from what I know its in Menu>Tools>Connectivity>Wireless LAN>Options>Settings>Show WLAn availability.
If you find my post helpful please click the green star on the left under the avatar. Thanks.

Can the time capsule works without WLAN cable connected to my DSL router?

Cna the Time capsule work without WLAN cable connection to DSL router?

WLAN is usually used for wireless LAN .. plainly you mean WAN port ..
How do you expect to get internet if the TC is not connected to the internet?
The TC can work stand alone.. true enough but that will then involve considerable issues in setting up two different IP addressing regimes .. you can just bridge the TC and use it as WAP and switch plus hdd without having to route.

Multiple DSL Connection

Hi folks. Hopefully someone has a solution for me.
A client of mine has a single DSL line and it isn't fast enough for his needs. So I thought of using a solution like back when the bound ISDN lines were used together to create a faster pipe.
How can I get faster speeds by using multi-channel DSL? Any routers out there that have this built in?
Cheers

A true bonded dsl connection also requires the ISP to bond the 2 lines at their end also.
Load balancing does not join 2 dsl connection to 1 fat pipe it just share the load as the name suggests.

Connecting 2 RV042 to different subnet and DSL connections

Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.
Is this doable without adding additional hardware? Both networks need DHCP enable as well.
Breakdown:
DSL 1
|
RV042
|
192.168.20.X
|
| Would like to somehow join the 2 networks together.
|
DSL 2
|
RV042
|
192.168.40.X

Hi Matt, you may utilize 1 RV042 router and host the dual wan for each connection then bind the appropriate services to the WAN. You then may enable the multiple subnet feature on the router to allow both separate LAN IP network communication through the LAN.
Next you can make very specific firewall rules for the specific services.
The caveat of this router firewall is that it has a default state table. To bypass the default state table you will need to make such a deny all rule for every field.
Then make a service rule to permit source ip to destination IP using which WAN for what service. (Confusing isn't it?)
Reference this topic to get an idea what I'm talking about.
https://supportforums.cisco.com/message/3828616#3828616
-Tom
Please mark answered for helpful posts

Multiple Controller GUI connection not working

Hi,
I have multiple WiSM's connected on the 6509 switch, sh wism stat will show me the all 4 management IP's, (two slots were powered on)
I am able to connect 1st controller GUI and do all my configurations, but when I try to use GUI other management IP it is not allowing to connect via Internet explorer.
what could be the problem.

Thanks for reply,
I have checked the WiSM status, all are up and i am able to ping
SUP720_A#sh wism stat
Service Vlan : 1000, Service IP Subnet : 192.168.XXX.1/255.255.255.0
      WLAN
Slot Controller Service IP       Management IP    SW Version Status
----+-----------+----------------+----------------+-----------+---------------
1     1           192.168.XXX.7     XXX.168.XX.68   7.0.98.0    Oper-Up
1     2           192.168.XXX.8     XXX.168.XX.69   7.0.98.0    Oper-Up
2     1           192.168.XXX.9     XXX.168.XX.70   7.0.98.0    Oper-Up
2     2           192.168.XXX.10    XXX.168.XX.71   7.0.98.0    Oper-Up
I have masked some part of IP address for confidentiality purpose..
I am able to take a GUI of only 1st Management IP address..

Multiple OLE DB connection managers to the same database instance in a SSIS package

Hi,
While migrating DTS package to SSIS package, I came across one which had multiple OLE DB connection managers all connecting to the same Oracle schema in the same instance.
There are that many execute SQL task corresponding to each of these connection managers.
Each of these SQL task call different Oracle stored procedures and executes them in the same schema in the same instance.
My question is, is there any particular reason or advantage in having multiple connection managers?
Can't we have one single connection manager and use the same in all of these SQL tasks?
Does multiple connection managers provide any added advantage like parallelism or something?
In this particular case, there are no actual workflows, rather each of these SQL tasks are stand alones. But there are other packages which has SQL tasks in workflow but still each of them calling separate connection managers all calling the same schema
in the same instance.
Thanks for your time.
Cordially, Biju George

Well like I said, each of these SQL task calls "different" Oracle stored procedures even though executes them in the same schema in the same instance. I tried a sample testing by creating two separate packages, one with only one single
OLE DB connection referred in all of the SQL tasks and in the other one with mutiple OLE DB connections to the same schema in the same instance each of which is referred in each of the SQL task in one to one mapping.
Now the first one created one session in Oracle but the later created as many sessions as there where OLE DB connection managers. The first one took longer to complete than the second one since second one created independent sessions and executed those procedures
sort of parallely.
I guess that can be called an advantage of creating multiple connection managers to the same schema in the same instance.
Cordially, Biju George

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

IOS device failed to get ip address on multiple wlan on the same anchor controller

Dear Experts:
in my implementation, we need 2 WLANs be served on the same anchor controller.
WLAN1: wep/40bit, integration with NAC/OOB on anchor controller for guest wlan service.
and guest account controlled by NACguest server.
WLAN2: wep/40bit, no layer3 secuirty for temporary using.
foreign controller: WiSM on v6.0.196.4 (also testing on 6.0.182.0)
anchor controller: WLC4402 on v6.0.196.4
on WLAN1:
Windows7 client get ip address correctly.
iOS (iPhone4 on 4.3.1/4.3.2, iPad2 on 4.3.1/4.3.2) can get ip address correctly on WLAN1.
WLAN2, iOS device cannot get ip address.
compare with debug message "debug clien mac" + "debug dhcp message enable"
on both foreign and anchor controller.
on foreign controller:
PM state has changed from: DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
on anchor controller:
PM state always stay on: DHCP_REQD (7) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
Enable/Disable DHCP Address Assignment Required is not work.
Enable/Disable DHCP proxy is not work.
Any hit this issue when get ip address failed in multiple WLANs on the same anchor controller?
In attachment log file,
DMZ.log: anchor controller on DMZ.
S3p1.log: WiSM on v6.0.182.0
S3p2.log: WiSM on v6.0.196.4
client mac: 00:1f:3b:05:33:c1, Windows7 Client
client mac: 58:55:ca:cf:d2:07, iPhone4 with 4.3.1,
WLAN1 subnet: 10.61.246.0/23
WLAN2 subnet: 10.61.248.0/23

Hi, Nicolas:
just checking the attachment for the run-config on foreign/anchor controller.
DMZ_run.config - anchor controller
s3p1_run.config - WiSM on v6.0.182.0
s3p2_run.config - WiSM on v6.0.196.4
at this moment, we have disable the wlan 10 on foreign controller, and wlan 2 on foreign controller.
Wilson...

Can I create a home network withous dsl connection with airport express

can I create a home network without dsl connection with airport express?
So it means I can't connect to my HP Airprint/Wireless printer without exretnal connection through ISP?? Just need to print from my Mac and iphone. I have Vodafone Prepaid connection, which is directly connected to my Mac. Does that make an internal network possible?

You have to set up the Air Port with an internet connection to set up a network. Do you have a modem? If yes you can set up the network.

Safari 6 stalling DSL connection

Here I am with the exact same issue Safari 5 had when it was released.
I installed Safari 6 on my MacBook Pro whilst waiting for my Mountain Lion to download. I like the new changes and the page rendering seems to be super fast. But it keeps stalling my DSL connection. I know it's not an Airport problem, and it's not my MBP (other devices on the network are unable to load pages once the connection has stalled); which leaves just the modem and connection. Connection is fine when I'm using Chrome.
After upgrading to Mountain Lion, the issue was still present. So i backed up and did a clean install of Mountain Lion and still no joy.
Advice, suggestions, and resolutions very much appreciated.
Thanks,
Transltr

Yeah I am having the same issue - befor and after ML. Following on from the same issue, online documents ie. google spreadsheets become un-clickable, youtube videos do not stream smoothly...

Flaky DSL connection

I have a DSL connection through Verizon that requires a username and password to get connected and once connected is always on. Now when I set this up with the DSL Modem/Router(it is a full router with all capabilites for networking like Linksys or Airport but a generic Westell verison) I inputted my username and password to log into the DSL Network. It has some firmware on it that requires the username and password be inputted into the router for the internet to connect properly. In the connection properties of the router it has DSL connection "connected/not connected" and Internet connection "connected/not connected". Also on my AEBS I have inputted my username and password for the DSL connection also.
It is working like this:
My DSL Modem/Router connects to the internet using my username and password. DHCP is disabled and wireless is also disabled. So it is acting like a bridge to just supply the internet connection. My AEBS is setup with the same username and password setup under PPOE over Ethernet. It has DHCP enabled with NAT and also my wireless network setup.
The question is since I have my username and password for the DSL incorporated into both Routers could that cause a problem with my connection? I am seeing connection drops and drops in bandwidth also. It will go anywhere from 50 KB to 160 KB and flux in between. I want to make sure before I go after Verizon for bad service. If its my fault I want to know before I accuse them of bad connections.
I was thinking of either setting up the DSL Router w/ my username and password and setting AEBS to just Ethernet and let it do everything else or take my username and password out of the DSL Router and just let my Aitport make the connection. Which would be best. Thanks in advance.
iMac G5 2.0 Ghz 1 Gig RAM, AP & BT, 400 Gig HD Mac OS X (10.4.8) iBook G3 700 Mhz 640 MB RAM Airpot

If i enable DHCP on the westell router it will give my AEBS a DHCP address and it will not function properly. I tried going through and disabling DHCP on my AEBS but it said to use PPoE you should leave DHCP enabled. Now if i remove the PPoE status on my AEBS and enable just Ethernet nothing goes throuh from that point on. It gets the IP from my router but then nothing functions. I was trying to figure out a way to let the westell be a gateway and make my PPoE connection for me and then once it hits the airport for it to distrubute IPs and do my wireless. The westell routr is generic and doesn't have many options. it came with my DSL setup package.
Now i did notice on the router it does have a routing table. Is it possible to setup a routing table to go straight to my AEBS and let it take it from there?
This is getting complicated now. I do tech support for networks for my day job and I have nevr seen anything this difficult to get working right. I think i might just call Verizon and try to get a dsl modem w/o a router and let my airport handle everything.

DSL connection gets slower than dial up at night

For the last week my DSL connection has been getting really slow in the late afternoon and evening. It is fine in the morning. Also in the evening I have started getting error messages such as Request Timeout, The connection was reset while the page was loading, and Can't find DNS server. Verizon has tried to blame my laptop, but the same thing happens with my two desktops and my wife's desktop. Verizon has also tried to blame my Belkin router, which I took out of the equation by hooking the DSL modem directly to my laptop. The modem is a Westell 6100G.
Could there be too much traffic through the CO in the afternoon and evening that is affecting my connection?
I have run the Verizon speed test with the following results:
Broadband Speed Test
Analysis information:
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
SendBufferSize set to [261360]
running 10s outbound test (client to server) . . . . . 330.89Kb/s
running 10s inbound test (server to client) . . . . . . 779.59kb/s
------ Client System Details ------
OS data: Name = Windows 7, Architecture = x86, Version = 6.1
Java data: Vendor = Sun Microsystems Inc., Version = 1.6.0_31
------ Web100 Detailed Analysis ------
Client Receive Window detected at 135024 bytes.
Cable modem/DSL/T1 link found.
Link set to Full Duplex mode
No network congestion discovered.
Good network cable(s) found
Normal duplex operation found.
Web100 reports the Round trip time = 944.73 msec; the Packet size = 1392 Bytes; and
No packet loss - but packets arrived out-of-order 0.24% of the time
This connection is receiver limited 37.82% of the time.
Increasing the the client's receive buffer (131.0 KB) will improve performance
This connection is sender limited 52.94% of the time.
This connection is network limited 9.25% of the time.
Web100 reports TCP negotiated the optional Performance Settings to:
RFC 2018 Selective Acknowledgment: ON
RFC 896 Nagle Algorithm: ON
RFC 3168 Explicit Congestion Notification: OFF
RFC 1323 Time Stamping: OFF
RFC 1323 Window Scaling: ON
Information: Network Middlebox is modifying MSS variable
Server IP addresses are preserved End-to-End
Information: Network Address Translation (NAT) box is modifying the Client's IP address
Server says [71.119.134.43] but Client says [192.168.2.2]
Here are my Transceiver stats:
Transceiver Statistics
Transceiver Revision
3.3.6.10.0.1
Vendor ID Code
4D54
Line Mode
ADSL_2plus
Data Path
INTERLEAVED
Transceiver Information
Down Stream Path
Up Stream Path
DSL Speed (Kbits/Sec)
928
287
Margin (dB)
25.4
27.2
Line Attenuation (dB)
36.5
15.2
Transmit Power (dBm)
17.8
12.0
Solved!
Go to Solution.

NDT Test is not showing packet loss yet the line sounds like it's behaving like there is a ton of loss occurring. I'll see if I can get someone. It's hard to say how Verizon has things set up but if 1Mbps is the top speed in your area and the sync rate was set that low deliberately rather than by some sort of provisioning accident, I wonder if your DSLAM is fed by bonded T1 lines. Not too uncommon to find that still to this day where DSLAMs are not fed by Fiber especially in very rural areas.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Multiple TCP/IP connections

Hello,
I am new with labview and I am trying to connect WAGO controller with LabVIEW 13 through modbus protocol via TCP/IP. Now, the question is how can I have multiple TCP/IP connections in the same LabVIEW project but different VIs? I am using MB ethernet master query.vi to write and read registers. Any suggestion would be very helpful to me.
Thanks and Regards

Yes, Nathan's idea is a good one to remember any time you have a common resource that will be accessed from multiple locations. In addition to instrumentation, I have used this idea for files and database connections.
An added benefit is that it allows you to redefine the interface to the resource to make it easier to access. In fact you could even use it to hide the exact nature of the resource you are accessing.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

Understanding multiple conditions in connect by prior clause Oracle

Hi ,
Can some one please explain me how to comprehend/understand multiple conditions in connect by prior conditions with some example data.
I am creating a table like this
CREATE TABLE FAMiLY_TREE
GRAND_FATHERID number,
FATHER_ID number,
SON_ID number,
person_name varchar(20)
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(NULL, NULL , 5 , 'Mr X ' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(null, 5 , 6 , 'Dave' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(5, 6 , 7 , 'Vinny' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(5, 6 , 16 , 'Omy' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(5, 6 , 17 , 'Vijjy' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(6, 7 , 8 , 'Vicky' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(6, 7 , 9 , 'Varis' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(7, 8 , 10 , 'Vshnu' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(7, 8 , 11 , 'dyna' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(8, 10 , 14 , 'Marry' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(8, 10 , 15 , 'Mac' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(7, 9 , 12 , 'Garry' );
INSERT INTO FAMILY_TREE (GRAND_FATHERID ,FATHER_ID , SON_ID , PERSON_NAME ) VALUES
(7, 9 , 13 , 'Ganny' );
SELECT
LPAD(' ', LEVEL*3) || PERSON_NAME FROM FAMILY_TREE
START WITH SON_ID= 6
CONNECT BY PRIOR SON_ID = FATHER_ID
AND PRIOR FATHER_ID = GRAND_FATHERID ;
SELECT
LPAD(' ', LEVEL*3) || PERSON_NAME FROM FAMILY_TREE
START WITH SON_ID= 6
CONNECT BY PRIOR SON_ID = FATHER_ID ;
Both These query return the same o/p
   Dave
      Vinny
         Vicky
            Vshnu
               Marry
               Mac
            dyna
         Varis
            Garry
            Ganny
      Omy
      Vijjy
Can some one please explain me comprehension of both these query or give me a example where i can understand multiple connect by prior conditions
Thanks

Maybe (something to play with)
with
family_tree as
(select 'Green' family,null ancestor,1 person,'Mr X' person_name,1900 born from dual union all
select 'Green',1,2,'Dave',1920 from dual union all
select 'Green',2,3,'Vinny',1940 from dual union all
select 'Green',2,4,'Omy',1945 from dual union all
select 'Green',2,5,'Vijjy',1950 from dual union all
select 'Green',3,6,'Vicky',1960 from dual union all
select 'Green',3,7,'Varis',1965 from dual union all
select 'Green',6,8,'Vshnu',1980 from dual union all
select 'Green',6,9,'Dyna',1985 from dual union all
select 'Green',8,10,'Mary',2000 from dual union all
select 'Green',8,11,'Mac',2005 from dual union all
select 'Green',7,12,'Garry',1985 from dual union all
select 'Green',7,13,'Ganny',1990 from dual union all
select 'Brown',null,14,'Joe',1950 from dual union all
select 'Brown',14,15,'Jim',1970 from dual union all
select 'Brown',14,16,'Joy',1975 from dual union all
select 'Brown',14,17,'Jay',1980 from dual union all
select 'Brown',16,18,'Jack',1995 from dual union all
select 'Brown',18,19,'Jake',2010 from dual union all
select 'Brown',18,20,'Jess',2012 from dual
select family,
       root_name||' ('||to_char(root_born)||')' "(FA/MO)THER",
       children
from (select family,
               root_born,
               root_name,
               ltrim(sys_connect_by_path(person_name||' ('||to_char(born)||')',', '),', ') children
          from (select family,
                       connect_by_root(person_name) root_name,
                       connect_by_root(born) root_born,
                       person_name,
                       born,
                       row_number() over (partition by family,connect_by_root(person_name) order by born) rn
                  from family_tree
                 where level = 2
                connect by prior person = ancestor
         where connect_by_isleaf = 1
         start with rn = 1
        connect by prior root_name = root_name
               and prior family = family
               and prior rn + 1 = rn
order by family desc,root_born
Regards
Etbin

Multiple WLANs & DSL connection

Similar Messages

Maybe you are looking for