Multiplexing error, Muxing preparation
Ok I have tried following iDVD's instructions by inserting a blank DVD when it asks. I've tried mounting the DVD on my Finder. I've even tried just making a dmg file from iDVD. I continue to get a Multiplexing error: There was an error during muxing preparation.
I've checked my chapter markers in iMovie. I've recompiled in iMovie without errors.
What is happening????
Thanks for the input. I had noted earlier in this project that I had about 50GB of free space on my system drive. After reading your comment, I checked and had only 20GB or so. In clearing out some disk space I found huge scratch file folders from iMovie in my Trash folder. Emptying the trash resulted in nearly 37GB of free space on this drive now. I'm currently trying to burn a very small project I had successfully burned as a test in iDVD before to see if I get the error. I suspect it is the scratch disk issue that has caused all of the fuss. Amazing how much drive space is eaten using these programs. I'm surprised that iMovie doesn't do better housekeeping.
As I typed the above I finished clearing nearly 37GB from my system disk and successfully burned the small test project directly from iDVD. I'm hoping that we've solved this problem. I know I'll be a lot more attentive to my scratch disk space. Thanks, I'll post it solved after I burn the first DVD of the real thing.
Similar Messages
-
?¿There was an error during muxing preparation (project conversion).?¿
*There was an error during muxing preparation (project conversion).*
can anyone elaborate on this?Same thing just happened to me. I re-output my quicktime movie with chapter markers turned off. You probably have a chapter mark set too close to the beginning, end or near a transition. I didn't have time to futz with the markers so I just turned them off.
Muxing stands for multiplexing. It's when iDVD takes all the data layers, video, audio etc. and multiplexes them into one data stream. When you play the dvd in your player that one data stream is DE-Muxed back into the original layers.
When you give iDVD a quicktime movie with chapter marks it encodes those chapters as separate mpeg 2 clips. When it muxes it combines everything into one stream. If there are any inconsistencies then muxing fails.
DVD Studio pro gives a more detailed log when muxing fails. It usually involves problems with chapter marks.
Message was edited by: Daniel Nocera -
Why is there an "error during muxing preparation?"
Suddenly I keep getting error messages in my iDVD 08 version 7.0.2 (1100). It was working fine a coupledays ago and then I upgraded to Snow Leopard (from 10.5.8 to 10.6.3) and I think at same time the install gave me QuickTime 10.0 (I had had QT 7.6.9 before). Now I’ve tried four short videos to burn DVD and each time I get the message “There was an error during muxing preparation (projection conversion).”I use Final Cut Express 4.0 and exported first via Quick Time movie and then via Mpeg4 to see if that made a difference. (It didn’t.) I’ve worked a long time to do a five-minute video on my eldest son to give him as a present, andnow I can’t burn it. Any and all help greatly appreciated. (BTW, on web, I saw that one issue might be I don’t have enough disc space, but I’ve got 101 GBfree, so that can’t be it.)
Desperate for advice... Thanks in advance for any help.Hello, John.
Looks like there are some other posts on this and it could be related to chapter markers and transitions. Also, Quicktime is a "container" format and the underlying format (codec) could be part of the problem -- have you used that specific format and work flow previously?
https://discussions.apple.com/message/6942255#6942255
https://discussions.apple.com/message/9946243#9946243
https://discussions.apple.com/message/5157904#5157904
John -
This site doesn't seem to get answers. I typed the problem above, then it asks same question before post. What help is that? Needs to be clearer what it wants from me. Others seem to have same issues with iDVD's clarity of information. I have been editing for 12+ years and still can't figure out solutions more than trail and error.
Hi
1:40 - can mean 1 sec 40 frames - or - 1 minute 40 seconds - or - 1 hour 40 minutes
1 hour 40 minutes is 100 minutes and iDVD only cares about duration
• Pro Quality encoding - up to 120 minutes (movie + menu) (menu can be 15 minutes or even more
• Best Performances - up to 60 min. - High quality on final DVD (Can be best for short movies)
• High Quality (in iDVD08 or 09) / Best Quality (in iDVD6) up to 120 min. - slightly lower quality than above
Reg "Multiplex Error" - This is a tough one and can have a lot of reasons. Read on
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
Why does iDVD keep giving me a multiplexing error and ejects my DVD?
I have tried several times to create a simple movie with iMovie and iDVD. Both are from the iLife 6.0 series. Each time, the movie imports to iDVD okay, goes through all the asset encoding just fine, and when it get to multiplexing and burning, it stops with a message saying there was something wrong with the multiplexing or asset encoding and ejects the DVD. Help. I am at my wits end with this.
dennisHi
Multiplex Error - is one of the most complex error to run into - can be so much
see (especially new info at end of list)
MULTIPLEX ERROR !
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev. (Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Max Mccarty
Mar 29, 2013 7:55 PM
I've made literally hundreds of DVD's using iDVD and I occasionally get the dreaded "Multiplex Error". In the past changing the position of chapter markers has worked, but sometimes the only way I can get the DVD to burn is to remove all the chapter markers (not a great solution).
Recently, I've discovered a bug in iDVD that creates the "Muliplex Error" message and it may be the cause of some of my previous problems. Sometimes when you export a movie to iDVD with chapters, it will create chapter menus with incredibly long playing times. My most recent "Multiplex Error" project had two chapter menus. I have a 38 second audio clip that I use for my DVD menus and the first menu showed the correct time of 38 seconds (select View>Show Inspector). The second menu with the same audio clip showed 13 minutes and 42 seconds! When I went to the Project Info window (select Project>Project Info) it now showed the total size of my DVD as 4.8 GB, too big for iDVD to encode. So, I manually adjusted the time of the second menu to 38 seconds. This time without changing anything else, iDVD burned the disk perfectly.
The interesting thing is that when I began the burn, the project info showed under 4GB for my disk. So, from now on I'll check the playing times of each menu before I burn.
Yours Bengt W -
I am trying to burn an imovie to a DVD. I keep getting the message multiplex error. I do not know what to do. Please, can anyone help me.
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev. (Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
I'm getting multiplexing error in iDVD when trying to burn.
Trying to finish an iDVD within 4 hours. I'm getting a multiplexing error when burning. It's a slide show with 429 pictures, background music and no movies.
Hi
You are aware of that - SlideShow function in iDVD has some limitations.
• 99 Photos per SlideShow (and You can have 99 of these)
• one audio tune (but You can make a special audio file/track including several Music parts - but as one track)
on MultiPlex Error - I've made a long long list - as this is a very complex error
Multiplexing Error
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
Why do I keep getting the multiplexer error the last 10 mins. or so when encoding assets.
Why has apple not fixed this yet.
There was an error during muxing preparation (project conversion). I have tried everything. This is supposed to be an easy quick dvd burn not a 2 week process.
NickHi
This is slightly occult to me so I collected some thoughts about it (unsorted)
May be You find help here.
*Multiplexing Error*
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else coverted to this .aff 48KHz)
Using strange letters in video project name eg +,/; etc. keep to a-z and 0-9
strange letters in project name eg +
as described by Donnyboy69: Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
from Robert Modero:
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
Yours Bengt W -
Problem burning dvd "multiplexer error"
Hi there, I am trying to burn a dvd using iDVD. Apologies for what may be a simple question but I am very new to Macs after a live with the evil PC!
All appears to start off well, the total project is about 6Gb, and I am using a double layer DVD+R. I have gone into the project settings and amended them to ensure that it is set and recognised as a dual layer disc.
All starts off well and the "Creating your DVD" screen runs down through "prepare", "process menus", "process slideshows", and "process movies"
It then starts the "Burn" section and the progress bar moves across whilst it says "muliplexing". It gets right to the end of this and then the following error comes up "Multiplexer Error - there was an error during formatting".
Any ideas or suggestions gratefully welcomed!
ThanksHi
As You see there are many things to consider - obvious onea and totally obscure ones.
Any button on or outside the TV-Safe area ? - Not obvious but that one hit me.
else - A very long list of thougts. (suggestion - print out and see if You pin down the culprit)
Multiplexing Error
PART One.
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else coverted to this .aff 48KHz)
*Chapters !*
A. *Using strange letters* in video project name eg +,/; etc. keep to a-z and 0-9 strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. *Location of Chapters*
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutly needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the uneditited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
*One user more writes*
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous trys, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no mulitplex error
As a final experiment, I moved "bad" chapter mark about 5-10 secs beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplexer Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Yours Bengt W -
Cannot create disk image iDvd 7.1.2 (multiplex error)
I'm at my wits end and extremely disappointed.
Basically, I've gone through the threads that I can find, I'm down to importing a basic movie directly into iDvd. No menus. No options enabled (that I'm aware of).
When I go through the iDvd process of creating a disk image all goes smoothy until the very end when I get a multiplexor error (no error code or text saying why).
Extremely frustrating. This is on a new Macbook Pro running 10.7.2. I don't have problems with my other Apple systems, just this new one. Perhaps Apple would like to take it back??Hi
Multiplexing Error
Multiplexing error is a very complex problem due to many things (long long list following) -
one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
Multiplexer Error on a 8GB disk burn or Disk image, iDVD
Burning 4.5GB DVDs burns fine.
While trying to burn a 8GB DVD or creating a disk image on iDVD I receive a "Multiplexer Error".
Another time, it burned and with about 3 minutes left the disk popped out of the computer although on the computer it appeared to still be burning. When I put this disk in a DVD player the chapter titles are mixed up with the actual video that plays and the same video is played over various chapters.
I tried changing the burning speed to 2X and tried using an external DVD burner.
Would appreciate any ideas!
ThanksSorry that I can not make a shorter answer !
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev. (Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
Only A to Z and 0 to 9 in chapter title
No Chapter mark at very beginning of movie
No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Max Mccarty
Mar 29, 2013 7:55 PM
I've made literally hundreds of DVD's using iDVD and I occasionally get the dreaded "Multiplex Error". In the past changing the position of chapter markers has worked, but sometimes the only way I can get the DVD to burn is to remove all the chapter markers (not a great solution).
Recently, I've discovered a bug in iDVD that creates the "Muliplex Error" message and it may be the cause of some of my previous problems. Sometimes when you export a movie to iDVD with chapters, it will create chapter menus with incredibly long playing times. My most recent "Multiplex Error" project had two chapter menus. I have a 38 second audio clip that I use for my DVD menus and the first menu showed the correct time of 38 seconds (select View>Show Inspector). The second menu with the same audio clip showed 13 minutes and 42 seconds! When I went to the Project Info window (select Project>Project Info) it now showed the total size of my DVD as 4.8 GB, too big for iDVD to encode. So, I manually adjusted the time of the second menu to 38 seconds. This time without changing anything else, iDVD burned the disk perfectly.
The interesting thing is that when I began the burn, the project info showed under 4GB for my disk. So, from now on I'll check the playing times of each menu before I burn.
Yours Bengt W -
I've been trying for what seems like days now to get iDVD to burn my dvd but I keep getting the "Multiplexer error". I've tried changing the speed to 4x then 2x and that didn't help. I've checked for software updates, restarted my Imac and idvd numerous times.
Is it possible anyone can give me a step by step guide of how to stop this issue? I really need to get this dvd burned a.s.a.p I have no apps or anything running on my Imac as I'm trying to burn a dvd and my Imac is pretty new it's got tons of space. It's 3am I've been working at this for hours with no sucess so far. I'm using Idvd 7.1.1Hi
Multiplex Error - Can be a lot of different things - one very common and not obvious is
• In iDVD - turn on TV-Safe area - NO buttons or pictures can go outside this OR EVEN Just touching it !
Move all well inside this !
Else
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else converted to this .aff 48KHz)
Chapters !
A. Using strange letters in video project name eg +,/; etc. keep to a-z and 0-9 strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous trys, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 secs beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref file
8. Make a new iDVD project
9. Movies in project with same aspect ratio eg 4x3 or 16x9
10. No other programs/applications running during iDVD process. eg Internet, screen & energy savers
Yours Bengt W -
I'm trying to burn an iMovie in iDVD and at the end of the whole burn process it says "Multiplexer Error" "there was an error during formatting". How do I fix it so that it'll burn?
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
Multiplexing error when saving as disc image
I have a very simply IDVD project. There is no film just a slideshow.
I am trying to save the project as a disc image to my desk top. I have no other programs running, the MAC is set to never sleep and I have set the processor perfromance to highest.
The project fails to save with Multiplexing errors. Any ideas?dpig,
Your digital image files may be to big. See Preparing images for DVD slideshows at http://docs.info.apple.com/article.html?path=iDVD/6.0/en/17.html -
Dvd burns through and says it has been completed with a multiplexer error. Please help i need this information as soon as possible.
Hi mryan:
Welcome to discussions.
iDVD 4: "Multiplexer Preparation Error"
http://docs.info.apple.com/article.html?artnum=93553
This article still applies even though it says iDVD 4.
You need to give us as much information about your mac, hard drive space, etc. for us to help further.
:)Sue
Maybe you are looking for
-
DirectAccess Windows Server 2012 R2 and Windows 8.1 - status connecting
I've successfully deployed DirectAccess on Windows Server 2012 R2 in a 2 node NLB cluster. Everything in the console is green and I can see clients connecting. Windows 7 clients can connect and with the DirectAccess connectivity assistant installed s
-
Hi All, We have an issue in our project. The asset value is 8534.96 in the books A user has first retired an asset on 9th Sep-06 for 7254.71. Another user has thereafter retired the same asset with the date 3rd Sep-06 with the correct amount 8534.96
-
ran out of room...how do i get the cd book onto my new macbook air? downloaded to old macbook from cd. goes on list when sync iphone with old mac. gets erased when sync with new macbook air thanks
-
HT1430 the Sleep/Wake button doesn't work
anyone else have this problem??
-
HDV video is 1080i60, FCE exports as 1080i50?
Exporting my 1080i60 project using the FCE "qucktime export" shows us as a 1080i50 file when played in QT. Also encodes to a PAL DVD format when using Compressor.