Multiplier Locked

I was recently looking to raise my FSB and lower my multiplier when I noticed it was locked and I can't seem to change it.
Is there any way to unlock it?
I have an MSI 865P Neo

not with a P4 they are all factory locked bar some engineering samples the public dont get hold off

Similar Messages

A88XM GAMING v1.5 BIOS CPU Multiplier Locked?

Since I updated to the latest v1.5 BIOS the CPU multiplier seems to be locked. Is this intended or an issue with BIOS, or am I just doing something wrong? The multiplier worked fine on v1.4. I am using an AMD Athlon 760k CPU. Thanks.

I cleared CMOS and it's working now, it's something I really should have done in the first place Thanks

X58 Pro and i7 920's 21X multiplier lock

Hi, I've read that many motherboards are capable of locking the 920's 21x turbo multiplier so it can be used for overclocking. So far I have been unsuccessful doing so with the X58 Pro. With EIST disabled, I manually selected the 21X multiplier in the bios. Unfortunately Windows still drops the multiplier down to 20x under full load. Is there some bios setting I'm missing or is this board simply not able to lock the turbo multipliers?

Perfectly normal , 920 has multiplier of 20 , under full load that is the max you will get on every board of any brand.
If you use HWmonitor http://www.cpuid.com/hwmonitor.php than you will see that your processor voltage with multiplier 21 max 150W is and if you stress cpu 100% it will drop to 130W that is the max TDP of the cpu. This is the meaning of turbo mode, if your cpu has power left (when you play game or other software because 100% load does not often happen) then the cpu uses this power to overclock one or two cores with one multiplier (21).
Msi made it possible to use turbo without EIST what is not seen often on motherboards because normally you need to use EIST witch is a power feature to use turbo.
If you google overclocking on core i7 you will see that many oc'ers disable this turbo mode because the don't want to use EIST.
I use EIST and turbo and my cpu is overclocked to 4083Mhz and under full load it falls back to 3926Mhz but in games it stays 4130Mhz if needed , but with EIST enabled my cpu falls back to 50% so 2130Mhz when surfing the internet or watching movie even in some games like cal of duty 5 my cpu fall's back to 2130Mhz because the game is not heavy on the cpu and i get constant frame rate off 90 FPS on 1920x1200 all max out.
With crysis the cpu goes to 4130Mhz , so this game uses the cpu more.(not for 100% because then it will fall back to 3926Mhz like when i encode movies to h.264)
I use EIST so my energy consumption is not so high when i don't play games.
But when i need the power turbo will kick in.

K9A2 CF Multipliers Locked

Hi
Is there a bios for this board with unlocked cpu multipliers as I would like to clock my 9600BE using Multipliers.
TIA
NemesisUK

I just got a reply from them telling me how to change the multi, they dont seem to understand that I cant even get to the setting as when I try it just skips over the option.
I'm now waiting a response now I explained that to them.
Ok just got another response stating that in a future bios the multi will be unlocked. I therefore look forward to this new bios at some point.

MOVED: X58 Pro and i7 920's 21X multiplier lock

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=129423.0

Perfectly normal , 920 has multiplier of 20 , under full load that is the max you will get on every board of any brand.
If you use HWmonitor http://www.cpuid.com/hwmonitor.php than you will see that your processor voltage with multiplier 21 max 150W is and if you stress cpu 100% it will drop to 130W that is the max TDP of the cpu. This is the meaning of turbo mode, if your cpu has power left (when you play game or other software because 100% load does not often happen) then the cpu uses this power to overclock one or two cores with one multiplier (21).
Msi made it possible to use turbo without EIST what is not seen often on motherboards because normally you need to use EIST witch is a power feature to use turbo.
If you google overclocking on core i7 you will see that many oc'ers disable this turbo mode because the don't want to use EIST.
I use EIST and turbo and my cpu is overclocked to 4083Mhz and under full load it falls back to 3926Mhz but in games it stays 4130Mhz if needed , but with EIST enabled my cpu falls back to 50% so 2130Mhz when surfing the internet or watching movie even in some games like cal of duty 5 my cpu fall's back to 2130Mhz because the game is not heavy on the cpu and i get constant frame rate off 90 FPS on 1920x1200 all max out.
With crysis the cpu goes to 4130Mhz , so this game uses the cpu more.(not for 100% because then it will fall back to 3926Mhz like when i encode movies to h.264)
I use EIST so my energy consumption is not so high when i don't play games.
But when i need the power turbo will kick in.

Kt3 ultra-aru multiplier prob

I just bought a new MSI kt3 ultra-aru from newegg and a new athlon xp 1900+(1.6ghz) and i unlocked it but the board wont boot with the new multiplier, so i thought the proc was not unlock so i try my old tbird which has already been unlocked and it does not work either, help Plz

Quote
Originally posted by WaltC
Quote
Originally posted by Shamael
Hello
I've got the same kind of problem with my MSI KT3 Ultra (no RAID).
Setting any multiplier below 9 would make the system unable to boot. I need to clear CMOS to be able reboot.
Setting the multiplier to 9 or above: no problem.
My CPU is an Athlon 1400 and its L1 bridges are "factory unlocked".
How could I fix this issue?
Many thanks.
Not that this may help, but years ago I had an old Pentium 2 that had its multiplier locked when going above its default, but unlocked when going below its default multiplier. It came this way from the factory. Pretty good FSB overclocker, btw.... :] Later I found that Intel had changed this and subsequent P2's came from the factory locked in both directions.
Might it be that the cpu is not as "unlocked" as you've been led to believe? Just a thought. A way to prove this one way or the other I think would be to try it in another motherboard.
Well, I don't think this is the same kind of issue because I used this Athlon 1400 with any multiplier on an ABIT KT7A before buying this MSI KT3.

Multiplier fix for K8N-Plat.

Hello all.
Is there a BIOS fix for the multiplier problem on the K8N ? Everytime i select a different MP than the original 11 he reboots and works. But once i restart a second time the computer hangs and i need to clear the CMOS. It is definetly not CPU or RAM related. What BIOS should i use for the K8N ?
Thank you for any help given.
Cheers

Quote
Originally posted by kdombaz
You can't change the multiplier in AMD64 CPU's they are multiplier locked. As for the BIOS reset issue before u switch ur PC on after wrong BIOS settings hold down Insert key and it'll start in safe values and go into BIOS straight away to set things to their correct values.
Hope this helps
Actually you can change the multiplier . You can decrease it all day long . You just can't increase it above the lock .
I didn't know that about the Insert key.... Wow, that sure beats popping the hood and foolin with the jumper . But I wonder, does it really work if you're system's not even posting? Can anyone confirm this? I'm not talking about a dead BIOS that has to be RMA'd. What I'm talking about is let's say computer won't start but you can get it back by reseting the jumper. In that situation, would this insert key thing work instead?

Multiplier only goes to 9x

is this normal on a 2800+ 9x multiplier i see people in the forum with 11x
also i have kingmax turbo 3500 ram what timings would u recomend for it

A64 is multiplier locked cpu's . You can use a lower one than your cpu's max multiplier but not higher .
s754 2800 max multiplier 9 (9*200=1,8ghz)
s754 3000 max multiplier 10 (10*200=2,0ghz)
s754 3200 max multiplier 11 (11*200=2,2ghz)
s754 3400 max multiplier 12 (12*200=2,4ghz)
s754 3700 max multiplier 12 (12*200=2,4ghz)
Only fx line has open multipliers .

865PE Neo2-S:CPU Ration LOCKED ??!!

Hi All,
I am using a P4 2.4C ghz CPU with it. When I go to "Frequency/Voltage Control", in the "CPU Ratio Selection", it says LOCKED !!! I can't change it. When I press "Enter" to go into submenu, it only gives me one option, which is "LOCKED".
Please help.
Thanks.

Quote
Originally posted by NovJoe
Hi ZhaoYun,
This is one important feature that msi has locked in their NEO boards. Reason is not very sure, but because Intel is afraid of dealers selling o/c systems using lower processing CPUs to customer and has implement a lock in the CPU ratio to prevent this. I used to have an Abit board which unlocks all feature including CPU ratio for o/c, but performance still lags behind this NEO board, although I have the Abit board to o/c my system to 2.66MHz and my NEO2 board to remain system speed at 2.4GHz.
This board is still out-performing many when keeping at original CPU speeds, unless if you\'re really keen on o/cing you can try Corecenter but I don\'t recommend tweaking from here if you\'ve read through carefully on how it o/c system. Anyway, it all depends on you whether to do or not to do.
All the Best... :D!!!
Intel CPU's are always multiplier locked. This is not MSI's fault. Intel decides what multiplier a CPU gets.
They have done this since the P133.

K8N Neo2 Platinum 54G BIOS problem

I recently bought a MSI K8N Neo2 Platinum-54G mainboard with W7025NMS v1.3 092204 revision of BIOS.
AMD Athlon64 3000+ 939 is installed on the mainboard, with 2x512 GEIL PC3200 memory modules in dual channel configuration working on default frequency of 200MHz. CPU is recognized correctly as AMD Athlon64 3000+ on startup.
Mainboard’s BIOS seems to be corrupted. In Cell Menu options, in the upper left part of the screen (printed blue) are processor and DDR working timings:
Current CPU Clock 1810MHZ, Current DDR Clock 200MHz.
Aggressive Timings and Dynamic Overclocking values are [Disabled] (processor working on its defaulf settings); Spread Spectrum is [Disabled] while all DRAM Configuration settings are set to [Auto].
While entering HT frequency settings, (locked to [x5]) there are no other values to select – empty, and there is no way to leave it (ESC doesn’t help, the only thing possible to do is to reset the computer by pressing the Reset button on the chassis), but the HT frequency settings were enabled when I loaded Fail-Safe settings, offering [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].
Adjust CPU Ratio settings offer only [StartUp], [x4]~[x9] values, but as I understood by reading the manual there should be [StartUp], [x4]~[x20].
CPU Voltage, Memory Voltage and AGP Voltage are set to default.
CPU-Z, as well as SiSoft Sandra 2004 and SiSoft Sandra 2005 and MSI CORE CELL show that processor works at a core speed ~1005MHz, showing multiplier locked on x5.0 and HTT locked at ~200MHz, while the voltage is ~1.05V!
I downloaded the latest BIOS revision (v1.4), did the BIOS flash, but the problem remains!
Anybody, help!

Quote
HT frequency
is a known fault in bios & is easily sorted Bas HT Bios Error
Quote
CPU Ratio settings
AMD64 CPOU's have a lock on CPU ratios which varies according to the specification of the chip. therefore the multiplier available in your bios stops at the max multiplier allowed by amd for your cpu.
As an example i'm running a 3200 754 which has a maximum muliplier of 11 so that is the max i see in bios.
this guide may help Bios Guide

Getting lag after change new mother board

i tried everything, installed my windows 5 times, upgrade all drivers, setting bios
but i still getting lag especially when playing warcraft tft game, all starts when i change my mobo ms-7313 v
please help me ,im getting stress b'coz of it .
please look at this, hope can help me with this prob!
Operating System: Microsoft Windows XP Professional 5.01.2600 Service Pack 2
Report Date: Friday 01 August 2008 at 03:48
<<< System Summary >>>
  > Mainboard : MICRO-STAR INTERNATIONAL CO.,LTD MS-7313
  > Chipset : Intel i945G/GZ
  > Processor : Intel Pentium 4 530J @ 3000 MHz
  > Physical Memory : 1536 MB
  > Video Card : NVIDIA GeForce 6600
  > Hard Disk : SAMSUNG (160 GB)
  > DVD-Rom Drive : TSSTcorp CDW/DVD SH-M522C
  > Monitor Type : RM170 -
  > Network Card : Realtek Semiconductor RTL8168/8111 PCI-E Gigabit Ethernet NIC
  > Operating System : Microsoft Windows XP Professional 5.01.2600 Service Pack 2
  > DirectX : Version 9.0c
<<< Mainboard >>>
  > Manufacturer : MICRO-STAR INTERNATIONAL CO.,LTD
   >> General Information
   Product : MS-7313
   Version : 1.0
   Serial Number : To Be Filled By O.E.M.
   Unique ID : FFFFFFFF-FFFFFFFF-FFFFFFFF-FFFFFFFF
   SKU : To Be Filled By O.E.M.
   Family : To Be Filled By O.E.M.
   Start mode : Power Switch
  > Mainboard : MICRO-STAR INTERNATIONAL CO.,LTD MS-7313
   >> General Information
   Manufacturer : MICRO-STAR INTERNATIONAL CO.,LTD
   Product : MS-7313
   Version : 1.0
   Serial Number : To be filled by O.E.M.
   Support MP : Yes, 1 CPU(s)
   Version MPS : 1.4
   >> Chassis Information
   Manufacturer : MICRO-STAR INTERNATIONAL CO.,LTD
   Type : Desktop
   Version : 1.0
   Serial Number : To Be Filled By O.E.M.
   Asset : To Be Filled By O.E.M.
   >> Sensor Information
   Hardware Monitoring : Fintek F71882FG
   >> On-Board Device Information
   Embedded Controller : Yes
   >> Slots Information
   >> External Connectors
  > Bios : American Megatrends Inc.
   >> General Information
   Manufacturer : American Megatrends Inc.
   Version : V1.1
   Date : 07/16/2008 (mm/dd/yyyy)
   Address : 0x0 on 512 KB
   Copyright : (C)2006 American Megatrends, Inc
   Motherboard ID : 63-0100-000001-00101111-071608-Lakeport-0AAAA000
   DMI Version : 2.5
   >> Characteristics
   Flashable : Yes
   Socketed : Yes
   >> Functionality
   APM : Yes
   ACPI : Yes
   ESCD : Yes
   PnP : Yes
   PCI : Yes
   ISA : Yes
   AGP : No
   USB : Yes
   PCMCIA : No
   Smart Battery : No
   >> Boot Information
   Selectable Boot : Yes
   CD-ROM Boot : Yes
   PC Card (PCMCIA) Boot : No
   I20 Boot : No
   LS-120 Boot : Yes
   1394 Boot : No
   ATAPI ZIP Boot : Yes
   Network Boot : No
  > Chipset : Intel i945G/GZ
   >> General Information
   NorthBridge : Intel i945G/GZ
   SouthBridge : 82801GB/GR (ICH7 Family) LPC Interface Controller
   >> NorthBridge Information
   Architecture : Direct Media Interface (DMI)
   Manufacturer : Intel (Micro-Star International Co Ltd (MSI))
   Codename : Lakeport
   Revision : A2
   Bus Speed : 201.7 MHz
   FSB Frequency : 806.6 MHz (QDR)
   FSB max. Support : 800 MHz
   RAM max. Support : DDR2 (667 MHz)
   >> Memory Information
   Type : DDR2-SDRAM PC2-4300
   Frequency : 268.9 MHz
   DRAM/FSB Ratio : 4/3
   Supported Channels : Dual (128-bit)
   Activated Channels : Dual
   ECC Diagnostic : No
   CAS Latency (tCL) : 4 clocks
   RAS to CAS (tRCD) : 4 clocks
   RAS Precharge (tRP) : 4 clocks
   Cycle Time (tRAS) : 11 clocks
   Bank Cycle Time (tRC) : 15 clocks
   >> PCI-Express Information
   Number of ports : 3 - (x16, x1, x1)
   >> Video Information
   Integrated Controller : No
   Enabled : No
   >> Functionality
   SATA AHCI Enabled : No
   RAID 0/1/10 Enabled : No
   RAID 5 Enabled : No
   PCI Express x1 Enabled : No
   Intel AMT : Yes
   Intel QST : No
   SPI Interface : Yes
   >> Device Capabilities (PCI)
   I/O Access : No
   Memory Access : Yes
   Bus Master Capable : Yes
   Special Cycle Recognition : No
   Memory Write & Invalidate : No
   VGA Palette Snoop : No
   Parity Error Response : No
   Cycle Wait : No
   System Error Line : No
   Fast Back-to-Back : No
   Detects Parity Errors : No
   User Defined Format : No
   PCI 66Mhz Bus Support : No
   New Capability List : Yes
   PCI Support : Vendor-Dependant
  > Physical Memory : 1536 MB DDR2-SDRAM
   >> General Information
   DIMM0 (RAS 0, RAS 1) : 512 (Single Bank)
   DIMM1 (RAS 4, RAS 5) : 1024 (Double Bank)
   >> Information SPD EEPROM (DIMM0)
   Manufacturer : Samsung
   Part Number : M3 78T6553BZ0-KD5
   Serial Number : 4601E3C3
   Type : DDR2-SDRAM PC2-4300 (266 MHz) - [DDR2-533]
   Format : Regular UDIMM (133.35 x 3)
   Size : 512 MB (1 ranks, 4 banks)
   Module Buffered : No
   Module Registered : No
   Module SLi Ready (EPP) : No
   Width : 64-bit
   Error Correction Capability : No
   Max. Burst Length : 8
   Refresh : Reduced (.5x)7.8 탎
   Voltage : SSTL 1.8v
   Prefetch Buffer : 4-bit
   Manufacture : Week 15 of 2005
   Supported Frequencies : 200 MHz, 266 MHz, 266 MHz
   CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @266 MHz
   RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
   RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
   Cycle Time (tRAS) : 8 clocks @200 MHz, 11 clocks @266 MHz, 11 clocks @266 MHz
   Min TRC : 11 clocks @200 MHz, 15 clocks @266 MHz, 15 clocks @266 MHz
   >> Information SPD EEPROM
   Manufacturer : Samsung
   Part Number : M3 78T2953CZ3-CD5
   Serial Number : F10A5A5B
   Type : DDR2-SDRAM PC2-4300 (266 MHz) - [DDR2-533]
   Format : Regular UDIMM (133.35 x 3)
   Size : 1024 MB (2 ranks, 4 banks)
   Module Buffered : No
   Module Registered : No
   Module SLi Ready (EPP) : No
   Width : 64-bit
   Error Correction Capability : No
   Max. Burst Length : 8
   Refresh : Reduced (.5x)7.8 탎, Self Refresh
   Voltage : SSTL 1.8v
   Prefetch Buffer : 4-bit
   Manufacture : Week 12 of 2007
   Supported Frequencies : 200 MHz, 266 MHz, 266 MHz
   CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @266 MHz
   RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
   RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
   Cycle Time (tRAS) : 8 clocks @200 MHz, 11 clocks @266 MHz, 11 clocks @266 MHz
   Min TRC : 11 clocks @200 MHz, 15 clocks @266 MHz, 15 clocks @266 MHz
   >> Memory Controller Information
   Memory Controller : DIMM, SDRAM
   Number of connectors : 2
   Supported Speed : Unspecified
   Supported Voltages : 3.3v
   Error Detection Method : 64-bit ECC
   Error Correction Capability : None
   Current/Supported Interleave : 1-way/1-way
  > LPC bus : Yes
   >> Bus Information
   Type : ISA - LPC
   Device : 82801GB/GR (ICH7 Family) LPC Interface Controller
   Revision : 01
   Number of ISA Connectors : 0
   >> Device Capabilities (PCI)
   I/O Access : Yes
   Memory Access : Yes
   Bus Master Capable : Yes
   Special Cycle Recognition : No
   Memory Write & Invalidate : No
   VGA Palette Snoop : No
   Parity Error Response : No
   Cycle Wait : No
   System Error Line : No
   Fast Back-to-Back : No
   Detects Parity Errors : No
   User Defined Format : No
   PCI 66Mhz Bus Support : No
   New Capability List : Yes
   PCI Support : Vendor-Dependant
  > PCI Bus : No
  > Bus PCI-Express : Yes
   >> PCI-Express Information
   Number of connectors : 1
   >> Bus PCI-Express
   Device : 82945G/GZ/P/PL PCIe Root Port
   Version : 1.0
   Port : 2
   Physical Slot : #0
   Slot Populated : Yes
   Link Width : x16 (max. x16)
   Link Speed : 2.5 GB/s
   >> Bus PCI-Express
   Device : 82801G (ICH7 Family) PCIe Root Port
   Version : 1.0
   Port : 1
   Physical Slot : #4
   Slot Populated : No
   Link Width : max. x1
   Link Speed : 2.5 GB/s
   >> Bus PCI-Express
   Device : 82801G (ICH7 Family) PCIe Root Port
   Version : 1.0
   Port : 2
   Physical Slot : #4
   Slot Populated : Yes
   Link Width : x1 (max. x1)
   Link Speed : 2.5 GB/s
   >> Bus PCI-Express
   Device : GeForce 6600
   Version : 1.0
   Port : 0
   Link Width : x16 (max. x16)
   Link Speed : 2.5 GB/s
  > USB Bus : Yes
   >> Device Information
   Device : 82801G (ICH7 Family) USB Universal Host Controller
   Version : 1.0
   Interface : UHCI
   Frequency : 48 MHz
   >> Device Information
   Device : 82801G (ICH7 Family) USB Universal Host Controller
   Version : 1.0
   Interface : UHCI
   Frequency : 48 MHz
   >> Device Information
   Device : 82801G (ICH7 Family) USB Universal Host Controller
   Version : 1.0
   Interface : UHCI
   Frequency : 48 MHz
   >> Device Information
   Device : 82801G (ICH7 Family) USB Universal Host Controller
   Version : 1.0
   Interface : UHCI
   Frequency : 48 MHz
   >> Device Information
   Device : 82801G (ICH7 Family) USB 2.0 Enhanced Host Controller
   Version : 2.0
   Interface : EHCI
  > SMBus/i2c Bus : Yes
   >> General Information
   Device : 82801G (ICH7 Family) SMBus Controller
   Revision : 1
   Frequency : 16 KHz
   Address : 0x400
   >> Device Capabilities (PCI)
   I/O Access : Yes
   Memory Access : No
   Bus Master Capable : No
   Special Cycle Recognition : No
   Memory Write & Invalidate : No
   VGA Palette Snoop : No
   Parity Error Response : No
   Cycle Wait : No
   System Error Line : No
   Fast Back-to-Back : No
   Detects Parity Errors : No
   User Defined Format : No
   PCI 66Mhz Bus Support : No
   New Capability List : No
  > Bus HyperTransport : No
  > Bus CardBus : No
  > Bus FireWire : No
<<< Processor >>>
  > Processor : Intel Pentium 4 530J
   >> General Information
   Type : Intel Pentium 4
   Internal Specification : Intel(R) Pentium(R) 4 CPU 3.00GHz
   Model Number : 530J
   Codename : Prescott
   Revision : E0
   Technology : 0.09μ
   CPU ID : F.4.1
   CPU IDEx : F.4.1
   Microcode : MU0F4117
   Number of Logical Processors : 2
   >> Instructions
   IA-64 Technology : No
   Intel64 (EM64T) : No
   AVX : No
   FPU128 : No
   SSE5 : No
   SSE4a : No
   SSE4.2 : No
   SSE4.1 : No
   S-SSE3 : No
   SSE3 : Yes
   SSE2 : Yes
   SSE : Yes
   Extended 3DNow! Technology : No
   3DNow! Technology : No
   3DNOW Prefetch : No
   3DNow! Pro Technology : Yes
   AMD MMX Technology : No
   MMX Technology : Yes
   Cyrix MMX Technology : No
   FMA : No
   AES : No
   OSXSAVE : No
   CLF - Cache Line Flush : Yes
   CX8 - CMPXCHG8B : Yes
   CX16 - CMPXCHG16B : No
   CMOV - Conditionnal Move Inst. : Yes
   MON - Monitor/Mwait : Yes
   POPCNT : No
   RDTSCP : No
   SEP - Fast System Call : Yes
   >> Miscellaneous
   XD - No-execute Page : No
   VT - Vanderpool Technology : No
   TXT - Trusted Execution Technology : No
   SVM - Secure Virtual Machine : No
   FPU - Co-processor Built-in : Yes
   FXSR - Fast Float Save & Restore : Yes
   xTPR - Send Task Priority : Yes
   DAZ - Denormals Are Zero : Yes
   FFXSR : No
   LAHFSAHF : No
   CMPLEGACY : No
   ALTMOVCR8 : No
   ExtApicSpace : No
   3DNow! Technology : No
   PBE - Pend. Brk. EN. : No
   LAHF - LAHF/SAHF Inst. : No
   ABM : No
   MASSE - Misaligned SSE : No
   OSVW - OS Visible Workaround : No
   IBS : No
   P1GB - 1GB Page Size : No
   SKINIT, STGI, DEV : No
   WDT - Watchdog Timer : No
   >> Features
   VME - Virtual Mode Ext. : Yes
   DE - Debugging Extension : Yes
   PSE - Page Size Extension : Yes
   TSC - Time Stamp Counter : Yes
   MSR - Model Specific Registers : Yes
   PAE - Physical Address Extension : Yes
   MCE - Machine Check Exception : Yes
   APIC - Local APIC Built-in : Yes
   MTRR - Memory Type Range Reg. : Yes
   PGE - Page Global Enable : Yes
   MCA - Machine Check Architecture : Yes
   PAT - Page Attribute Table : Yes
   PSE36 - 36-bit Page Size Extension : Yes
   PSN - Unique Serial Number : No
   DS - Debug Trace & EMON Store : Yes
   SS - Self Snoop : Yes
   ACPI - Software Clock Control : Yes
   TM - Thermal Monitor : Yes
   TM2 - Thermal Monitor 2 : No
   EST - Enhanced SpeedStep Technology : No
   HTT - Hyper-Threading : Yes
   SBF - Signal Break on FERR : Yes
   DSCPL - CPL qualified Debug Store : Yes
   CID - Context ID : Yes
   LT - LaGrande Technology : No
   PDCM : No
   DCA - Direct Cache Access : No
   EPS - Enhanced PowerSaver : No
   >> Features Hyper-Threading
   Technology : Yes - Enabled
   Physical Processor #1 : Apic ID 0
   Logical Processor #1 : Apic ID 1
   >> Addressing Information
   Physical Addressing max. : 36-bit
   Linear Addressing max. : 32-bit
   >> Advanced Settings
   In Order Queue Depth : 12
   Fast-Strings : Yes
   x87 FPU Opcode : No
   Thermal Monitor : Yes
   Split-Lock : Yes
   Performance Monitoring : Yes
   Prefetch Queue : Yes
   Branch Trace Storage : Yes
   C1E - Enhanced Halt State : Yes
   Temperature Control : 66 °C
   PRB - Performance Requirement Bit : No
   >> Mainboard Upgradeability
   Socket/Slot : CPU 1
   Upgrade interface : Unspecified
   Supported Speed : 3000 MHz (or more)
   Supported Voltage : 1.3V
  > Frequency : 3000 MHz
   >> General Information
   Real Frequency : 3024.85 MHz
   Multiplier : 15x
   Low/High Multiplier : 14x / 15x
   Multiplier Locked : Yes
   Marketing Frequency : 3000 MHz
   >> Front Side Bus Information
   Bus Speed : 201.7 MHz
   FSB Frequency : 806.6 MHz (QDR)
   >> Initial Frequencies
   Frequency : 3000 MHz
   Bus Speed : 200.00 MHz (QDR)
   Multiplier : 15x
   >> Control Clock Frequency
   Type : None
   >> Thermal Information
   Thermal Design Power : 89 W
   Core Power : 89.74 W (estimated)
   Resistance : 0.14 °C/W (estimated)
   Thermal control TM1 : Yes - Enabled
   Thermal control TM2 : No
   Thermal Control Circuit : No
   Digital Thermal Sensor : No
   Clock Modulation (ODCM) Enabled : No
   >> Processor Performance Information
   Throttle Mode AC : None
   Throttle Mode DC : Adaptive
   Current Configuration : None
   Throttle : 3025 MHz
  > Support : Socket 775 LGA
  > Data Cache L1 : 16 KB
   >> General Information
   Write Mode : Write-Through
   Place : Internal
   Correct : Parity
   >> Cache Information
   Data Cache : 16 KB (8-way, 64 bytes line size)
   L1 Context Mode : Adaptive
   >> Cache Parameters
   Type : Data Cache
   Ways of associativity : 8
   Fully Associative : No
   System Coherency Line Size : 64
   Physical Line partitions : 1
   Number of threads sharing : 2
   Number of processor cores : 1
   Number of Sets : 32
  > Trace Cache L1 : 12 Kμops
   >> Cache Information
   Trace Cache L1 : 12 Kμops (8-way)
   >> Cache Parameters
   Type : Data Cache
   Ways of associativity : 8
   Fully Associative : No
   System Coherency Line Size : 64
   Physical Line partitions : 1
   Number of threads sharing : 2
   Number of processor cores : 1
   Number of Sets : 32
  > Cache L2 : 1024 KB
   >> General Information
   Write Mode : Write-Back
   Place : Internal
   Multiplier : 1/1x (3024.9 MHz)
   Correct : Single-bit ECC
   >> Cache Information
   Associativity : 8-way
   Line Size : 64 bytes
   Bus : 256-bit
   Prefetch Logic : Yes
   >> Cache Parameters
   Type : Unified Cache
   Ways of associativity : 8
   Fully Associative : No
   System Coherency Line Size : 64
   Physical Line partitions : 2
   Number of threads sharing : 2
   Number of processor cores : 1
   Number of Sets : 1024
  > FPU Coprocessor : Present
   >> General Information
   Integrated : Yes
   Model : Compatible Intel
  > Processor activity : : 0%
<<< Video >>>
  > Number of monitor : 1
   >> Monitor Information #1
   Monitor : 플러그 앤 플레이 모니터
   Linked on : NVIDIA GeForce 6600
   Resolution : 1280x1024
   Working desktop : 1280x994
   Main monitor : Yes
  > Monitor Type : RM170
   >> General Information
   Product ID : SEG1A85
   Model : RM170
   Serial Number : H111701830
   Manufacture : Week 21 of 2002
   Video Input Type : Analogic
   Aspect Ratio : 16:10
   Gamma Factor : 3.55
   DPMS Active-Off : Yes
   DPMS Suspend : Yes
   DPMS Standby : Yes
   EDID version : 1.3
   >> Features
   Maximum Resolution : 1280 x 1024 @ 60 Hz
   Horizontal frame rate : 30 - 80 kHz
   Vertical frame rate : 58 - 75 Hz
   Bandwidth : 140 MHz
   >> Video Modes Supported
   Mode : 720 x 400 @ 70 Hz
   Mode : 640 x 480 @ 60 Hz
   Mode : 640 x 480 @ 67 Hz
   Mode : 640 x 480 @ 75 Hz
   Mode : 800 x 600 @ 60 Hz
   Mode : 800 x 600 @ 72 Hz
   Mode : 800 x 600 @ 75 Hz
   Mode : 832 x 624 @ 75 Hz
   Mode : 1024 x 768 @ 87 Hz interlaced
   Mode : 1024 x 768 @ 75 Hz
   Mode : 1280 x 1024 @ 75 Hz
  > Video Card : NVIDIA

Create a signature with PC components and PSU specs, see our sigs for examples of what to provide.
Example of PSU specs: Corsair VX450W, +3.3V~20A, +5V~20A, +12V~33A
To create signature:
Click on PROFILE above (near top of this page) and then in your "Profile", what I show in red below under "Modify Profile", scroll down to "Signature" and enter your specs in the box and then click on "Change profile" button on the bottom.
Profile Info
Summary
Show Stats
Show Posts
Modify Profile
Account Related Settings
Forum Profile Information
Look and Layout Preferences
Notifications and Email
Personal Message Options

Step By Step Overclocking 2400 xp athlon,

hey guy i know there are some smart guys in here so i would like to ask one for you guys to write a step by step guide to over my athlon 2400xp.
i have a K7N2 Delta-L
(SPP+MCP2, Onboard 10/100 LAN)
thanks guys for your time
marc,

a this is the nvidia forum not the overclockers forum
we are trying to keep them seperate
but never mind your hear now
b how old the cpu as newer ones are multiplier locked and evan wire trick dont work,
c what speeds the ram pc 2100 2700 3200 make model etc
go read stickies in that section re wire tricking etc

X79A-GD45 (8D) OCP always enabled?

Hi guys,
Is there a way to disable the OCP in the X79A-GD45 (8D)? It seems I have 2 options: "Default" and "Enhanced". Enhanced buys me a little bit more room, but currently I'm stuck at 4.5GHz @ 1.425V. Anymore voltage and the processor just immediately clicks off as soon as I start Prime95.
I have a very hardcore water-cooling system. ApogeeXT + quad radiator + 2x MCP35X to drive the whole thing, so I can probably put some serious voltages into the thing if the board will let me.

Sorry, it would be nice to list the CPU eh? It's a 3930K.
Quote
You are already overvolting the CPU past Intel's published datasheet absolute maximum as it is for a 3930k or 3960X by .25v's.
Anyways, I'm convinced that Intel's datasheets are much too conservative. I have an i7-920 here that has been running 4 GHz @ 1.5V for almost 2 years now. The thing also hit 100C (obviously this was an air cooler) from time to time when I ran torture tests on it and yet nothing bad has come of it yet. I'm an EE by trade so I understand the problems of inverse relationship between lifespan and voltage, but you can't really destroy modern day silicon chips unless you SERIOUSLY exceed the voltages (25%+)
I'm currently water-cooled with a Apogee XT and a quad radiator and dual pumps, so the temp on the processor even at 1.425 is 55C under load so cooling is not the issue here.
Quote
Just keeping cranking the volts to it until it is stable or pops at the set speed.
That's kind of my point, the motherboard OCP protection won't let me crank the volts. I witness this problem whether I'm multiplier locked to 1.2 GHz or 4.6 GHz. Actually my CPU will take 1.6V and boot at 5.2 GHz to Windows desktop. But as soon as I put any kind of load on it, the OCP kicks in and ends my fun. My question is, is there a way of disabling it? The manual says that it can be disabled, but I assume this is because they just took a GD65 manual and changed 65 to 45. Is MSI good with BIOS updates for this sort of thing or should I go ahead and return the board and get something a bit more.. supported?

K9n SLI V2

hi guys
i need a little help here i have upgraded my cpu to a phenom 9500 and after getting it up and running i went into the bios to do some tweaking and i can no longer adjust the multiplyer or cpu voltage its currently set to auto but will not let me change anything as they have been locked out.
i know all of the amd chips are multiplyer locked except for the black editions, I used to be able to overclock my old chip which was a 5000+ clocked at 2.8ghz stable by adjusting the fsb to 225 and a multi of 12.5 on watercooling.
but now it wont play ball.
IS THERE ANY WAY OF OVERCOMING THIS PLZ HELP!!!!!!

ISSUE SOLVED
flashed board with final 1.2 bios release
unlocked and clocked at a whopping 2.76 ghz with 1.25 core voltage
i could have gone more but this board will not allow above 1.25 core volts with a phenom installed

[915 Series] 915G dont reconyze my G.Skill as pc3200!

My new memory G.Skill (F1-3200PHU2-1GBZX http://www.gskill.com/f1-3200phu2-zx.html ) its not reconyzed as pc3200 and its runing at 266(133) !!!
My Syntem: MSI 915G(bios 1.6), MSI X600XT, Win XPse etc
I can manually set the DDR frequency to 400mhz but it makes no difference. The only way i can raise it back to DDR400 is to up the CPU FSB to 240, with the multiplier locked this makes my 3.0G cpu into a 3.6 and to be honest i dont want to go down that road.
The ratio was changed to 5 : 4 and i cant change this option on 915G. I think the devider is holding somehow this frequencie.
When i put back my old Corsair Value on it everything its fine again. Ratio 1:1.
Sorry about my english
Any advide.... cheers

Check if you've something called spread spectrum in your BIOS, if there's one, disable it.
Next, we don't have any beta BIOS here as this is a user to user forum so please contact MSI directly with regards to this.
How to contact MSI.

Multiplier Locked

Similar Messages

Maybe you are looking for