MVA Directory Number - Not Reachable
I am trying to configure MVA in a CUCM 9.1 and a SIP Gateway but it's not working. I can hear the IVR prompts but I get disconnected if I try to make a call. The IVR options to turn on/off Unified Mobility are working. I have checked in SIP trace messages and CUCM sent a "SIP/2.0 404 Not Found" message after the INVITE message from sip gateway. Note that I cannot dial the MVA DN from internal extension (Your call cannot be completed as dialled...). I have checked Partitions/CSS. The MVA DN partition belongs to inbound CSS of the gateway.
(Attached is the SIP messages on the gateway after I dial the number)
Hi
It looks this is sure could be an issue with the partition/CSS. check you have done the following config steps,
Enable MVA service from serviceability page
- Enable end user for Mobile Voice Access
- Configure MVA number (accessible from PSTN) under Media Resources > MVA
- Cisco Callmanager service parameter for MVA to true
- Configure the VXML gateway (inbound dial peer to play the IVR, and outbound dialpeer to CallManager)
Please rate if this helps
Thanks
Similar Messages
-
When we start essbase we recive Native Directory is not reachable.
Hi All,
While i start essbase i get the below error.
[Wed Apr 29 17:57:29 2009]Local/ESSBASE0///Info(1051283)
Retrieving License Information Please Wait...
[Wed Apr 29 17:57:29 2009]Local/ESSBASE0///Info(1051286)
License information retrieved.
[Wed Apr 29 17:58:19 2009]Local/ESSBASE0///Error(1051223)
Single Sign On function call [css_init] failed with error [Native Directory is not reachable. ]
[Wed Apr 29 17:58:19 2009]Local/ESSBASE0///Info(1051198)
Single Sign-On Initialization Failed !
[Wed Apr 29 17:58:19 2009]Local/ESSBASE0///Info(1051232)
Using English_UnitedStates.Latin1@Binary as the Essbase Locale
I am able to ping the shared service server.
Able to create a user in native directory.
Able to login shared services from essbase server.
restarted the openldap and shared services.
Please help.
Regards,
Mink.
http://newhyperion-blog.blogspot.com/(May 06, 2009, 02:44:59 PM), com.hyperion.cis.config.InitConfigurator, DEBUG,
---- Initializing Configuration Utility...
(May 06, 2009, 02:45:00 PM), com.hyperion.cis.config.Configurator, DEBUG, Hyperion Home: E:\Hyperion
(May 06, 2009, 02:45:00 PM), com.hyperion.cis.config.Configurator, DEBUG, Localhost Name: machinename
(May 06, 2009, 02:45:00 PM), com.hyperion.cis.config.Configurator, INFO, Loading product descriptor from file E:\Hyperion\common\config\product\essbase\9.3.1.0.0\essbase_1.xml...
(May 06, 2009, 02:45:00 PM), com.hyperion.cis.config.Configurator, INFO, Loaded product "Essbase", version 9.3.1.0.0, build 100.
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, Checking OS type/version/architecture against system requirements...
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, os.name: Windows 2003
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, os.version: 5.2
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, os.arch: amd64
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, major os version #:5; minor os version #: 2
(May 6, 2009 2:45:02 PM), Install.product.install, com.hyperion.essbase.config.EssbaseAgentTaskProcessor, dbg, Initialized EssbaseAgentTaskProcessor
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, tasks[0] = licenseActivation
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, tasks[1] = hubRegistration
(May 06, 2009, 02:45:02 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, tasks[2] = RegisterEssbaseAsMultipleAgent
(May 6, 2009 2:45:02 PM), Install.product.install, com.hyperion.essbase.config.EssbaseAgentTaskProcessor, dbg, Entered EssbaseAgentTaskProcessor.getDisplayName()
(May 6, 2009 2:45:02 PM), Install.product.install, com.hyperion.essbase.config.EssbaseAgentTaskProcessor, dbg, Display name returned : Register Analytic Services Server as Windows Service
(May 6, 2009 2:45:02 PM), Install.product.install, com.hyperion.essbase.config.EssbaseAgentTaskProcessor, dbg, Entered EssbaseAgentTaskProcessor.getDisplayName()
(May 6, 2009 2:45:02 PM), Install.product.install, com.hyperion.essbase.config.EssbaseAgentTaskProcessor, dbg, Display name returned : Register Analytic Services Server as Windows Service
(May 06, 2009, 02:45:07 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, INFO, Validating dependencies...
(May 06, 2009, 02:45:07 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel$5, DEBUG, Product: Essbase; Dependencies: []
(May 06, 2009, 02:45:07 PM), com.hyperion.cis.config.wizard.ProductTaskSelectionPanel, DEBUG, task to execute: hubRegistration
(May 06, 2009, 02:45:07 PM), com.hyperion.cis.config.wizard.PanelEventDispatcher, DEBUG, constructor
(May 06, 2009, 02:45:07 PM), com.hyperion.cis.config.wizard.HubRegistrationPanel, DEBUG, Hub registration is selected
(May 06, 2009, 02:45:20 PM), com.hyperion.cis.config.CmsRegistrationUtil, DEBUG, Getting CSS instance
(May 06, 2009, 02:45:20 PM), com.hyperion.cis.config.CmsRegistrationUtil, DEBUG, URL for CSS.xml = http://machinename:58080/interop/framework/getCSSConfigFile
(May 06, 2009, 02:45:21 PM), com.hyperion.cis.config.CSSApp, DEBUG, Unable to communicate with the server.
(May 06, 2009, 02:45:21 PM), com.hyperion.cis.config.CSSApp, DEBUG, Unable to communicate with the server.
(May 06, 2009, 02:45:21 PM), com.hyperion.cis.config.CmsRegistrationUtil, DEBUG, Authenticate admin user to CSS.
(May 06, 2009, 02:45:22 PM), com.hyperion.cis.config.CSSApp, DEBUG, com.hyperion.css.CSSCommunicationException: Failed to connect to the directory server: Native Directory. Error Code: 3
NestedException:
javax.naming.CommunicationException: svamn14glbsmb8.us.bank-dns.com:58089 Root exception is java.net.UnknownHostException: machinename
(May 06, 2009, 02:45:22 PM), com.hyperion.cis.config.CmsRegistrationUtil, ERROR, Failed to authenticate user = admin -
Status Agent Not Reachable - How to set a fix port number?
My EM 10g was working fine http://localhost:5500/em
Now when I tried, it was not working. I looked into portlist and found out it there was additional port of 5502
But when I logged into port 5502, Status Agent Not Reachable. Other links were working fine.
I had even installed another DB called REPOS other than the default ORCL.
All the services were up and running and I was just bouncing services back and forth and luckly I got the original port 5500 to work and then I did not got the error "Status Agent Not Reachable".
So I just wanted to know how to set a dedicated port in case the port number changes back to 5502 and if I get the error again.
Thanks in advance.Yes I installed multipe databases for eg ORCL was the default but I installed REPOS.
I did not uninstall the db.
Why does it show two different ports for ORCL 5500 and 5502 and for Repos it shows two ports but they are the same 5501.
Everything is on my local machine.
Following is from the portlist
Ultra Search HTTP port number =5620
Enterprise Manager Agent Port =
iSQL*Plus HTTP port number =5560
Enterprise Manager Console HTTP Port (orcl) = 5500
Enterprise Manager Agent Port (orcl) = 1830
Enterprise Manager Console HTTP Port (repos) = 5501
Enterprise Manager Agent Port (repos) = 1831
Enterprise Manager Console HTTP Port (ORCL) = 5502
Enterprise Manager Agent Port (ORCL) = 1830
Enterprise Manager Console HTTP Port (repos) = 5501
Enterprise Manager Agent Port (repos) = 1831 -
Lync 2010 phone not available when users have two Directory Number Associations in CUCM
Hello everyone,
We currently have a little issue with our LYNC 2010 to Cisco UC Integration (CUCM 8.5.1), I’m wondering if someone can shed some light please.
There are some users in our organisation having two Directory Number Associations in CUCM (Primary Extension for work number and IPCC Extension for team number), which result them not be able to dial out from Lync. For these users, it appears the Cisco phone
is not available in Lync.
I tried to disable the team number from them, and after reboot, the Cisco phone came back available and dialing out from Lync was enabled.
Is there any workaround for this issue? Thank you in advance.
ShawnAs far as Lync concern lync only do a number translation and send the call to cisco for reaching the destination.So you have to check how the call split is configured for users with respect to the team number and Extension.So in this case you need to have
2 different dial pattern to cisco based on how they accept the calls.
One pattern will translate the Primary extension number to the format cisco accept
Second pattern to translate the Team extension number to the format cisco accept.
Jayakumar K -
403 Forbidden Error on directory but not on index page.
I can't seem to find the source of the 403 Forbidden error. Index page works as expected but accessing the owncoud directory throws this error. Configs below.
httpd.conf
condensed:
ServerRoot "/etc/httpd"
Listen 80
LoadModule authn_file_module modules/mod_authn_file.so
LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
LoadModule authz_core_module modules/mod_authz_core.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
LoadModule mime_module modules/mod_mime.so
LoadModule log_config_module modules/mod_log_config.so
LoadModule env_module modules/mod_env.so
LoadModule headers_module modules/mod_headers.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
LoadModule ssl_module modules/mod_ssl.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
LoadModule mpm_prefork_module modules/mod_mpm_prefork.so
LoadModule unixd_module modules/mod_unixd.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
LoadModule php5_module modules/libphp5.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
<IfModule unixd_module>
User http
Group http
</IfModule>
ServerAdmin [email protected]
<Directory />
AllowOverride none
Require all denied
</Directory>
DocumentRoot "/srv/http"
<Directory "/srv/http">
Options Indexes FollowSymLinks
AllowOverride None
Require all granted
</Directory>
<Directory "/srv/http/owncloud">
Options Indexes FollowSymLinks
AllowOverride None
Require all granted
</Directory>
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
<Files ".ht*">
Require all denied
</Files>
ErrorLog "/var/log/httpd/error_log"
LogLevel warn
<IfModule log_config_module>
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
CustomLog "/var/log/httpd/access_log" common
</IfModule>
<IfModule alias_module>
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
</IfModule>
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
TypesConfig conf/mime.types
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
</IfModule>
Include conf/extra/httpd-mpm.conf
Include conf/extra/httpd-multilang-errordoc.conf
Include conf/extra/httpd-autoindex.conf
Include conf/extra/httpd-languages.conf
Include conf/extra/httpd-userdir.conf
Include conf/extra/httpd-default.conf
Include conf/vhosts/itiest.com
Include conf/extra/php5_module.conf
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
Include conf/extra/httpd-ssl.conf
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
Include conf/extra/owncloud.conf
With Comments:
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used. If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "/etc/httpd"
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:/run/httpd
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
#LoadModule authnz_fcgi_module modules/mod_authnz_fcgi.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule allowmethods_module modules/mod_allowmethods.so
#LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule cache_socache_module modules/mod_cache_socache.so
LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule dumpio_module modules/mod_dumpio.so
#LoadModule echo_module modules/mod_echo.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule data_module modules/mod_data.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule request_module modules/mod_request.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule deflate_module modules/mod_deflate.so
#LoadModule xml2enc_module modules/mod_xml2enc.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
LoadModule mime_module modules/mod_mime.so
#LoadModule ldap_module modules/mod_ldap.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule logio_module modules/mod_logio.so
#LoadModule lua_module modules/mod_lua.so
LoadModule env_module modules/mod_env.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
#LoadModule expires_module modules/mod_expires.so
LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule unique_id_module modules/mod_unique_id.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
#LoadModule remoteip_module modules/mod_remoteip.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_fdpass_module modules/mod_proxy_fdpass.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
LoadModule ssl_module modules/mod_ssl.so
#LoadModule dialup_module modules/mod_dialup.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
LoadModule mpm_prefork_module modules/mod_mpm_prefork.so
#LoadModule mpm_event_module modules/mod_mpm_event.so
LoadModule unixd_module modules/mod_unixd.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#LoadModule dav_module modules/mod_dav.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule asis_module modules/mod_asis.so
#LoadModule info_module modules/mod_info.so
#LoadModule suexec_module modules/mod_suexec.so
#LoadModule cgid_module modules/mod_cgid.so
#LoadModule cgi_module modules/mod_cgi.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
LoadModule php5_module modules/libphp5.so
#LoadModule imagemap_module modules/mod_imagemap.so
#LoadModule actions_module modules/mod_actions.so
#LoadModule speling_module modules/mod_speling.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
#LoadModule rewrite_module modules/mod_rewrite.so
<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User http
Group http
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
<Directory />
AllowOverride none
Require all denied
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/srv/http"
<Directory "/srv/http">
# Possible values for the Options directive are "None", "All",
# or any combination of:
# Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# Note that "MultiViews" must be named *explicitly* --- "Options All"
# doesn't give it to you.
# The Options directive is both complicated and important. Please see
# http://httpd.apache.org/docs/2.4/mod/core.html#options
# for more information.
Options Indexes FollowSymLinks
# AllowOverride controls what directives may be placed in .htaccess files.
# It can be "All", "None", or any combination of the keywords:
# AllowOverride FileInfo AuthConfig Limit
AllowOverride None
# Controls who can get stuff from this server.
Require all granted
</Directory>
<Directory "/srv/http/owncloud">
Options Indexes FollowSymLinks
AllowOverride None
Require all granted
</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<Files ".ht*">
Require all denied
</Files>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/var/log/httpd/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you *do*
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and *not* in this file.
CustomLog "/var/log/httpd/access_log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "/var/log/httpd/access_log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://www.example.com/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock cgisock
</IfModule>
# "/srv/http/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
#EnableSendfile on
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf
# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include conf/extra/httpd-autoindex.conf
# Language settings
Include conf/extra/httpd-languages.conf
# User home directories
Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
#Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
Include conf/extra/httpd-default.conf
## vhosts
Include conf/vhosts/itiest.com
Include conf/extra/php5_module.conf
# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
# Secure (SSL/TLS) connections
Include conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#</IfModule>
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT
#</IfModule>
Include conf/extra/owncloud.conf
##open_basedir=/srv/http/:/home/:/tmp/:/usr/share/pear/:/path/to/documentroot
$ ls -al /srv/http/
total 16876
drwxr-xr-x 4 root http 4096 Mar 6 17:51 .
drwxr-xr-x 4 root root 4096 Feb 15 13:57 ..
-rwxrwxrwx 1 root http 295 Mar 6 11:51 index.html
drwxrwxr-x 11 http http 4096 Feb 6 18:33 owncloud
-rw-r--r-- 1 root root 17200380 Feb 6 18:41 owncloud-8.0.0.tar.bz2
-rw-r--r-- 1 root root 52966 Mar 6 11:49 smallpizza.jpg
-rw-r--r-- 1 root root 20 Mar 6 16:24 test.php
# groups http
wheel http
Last edited by johan1391 (2015-03-07 04:11:12)/var/log/httpd/owncloud-error.log
192.168.1.1 - - [06/Mar/2015:17:52:02 -0800] "GET /owncloud/ HTTP/1.1" 403 1002
192.168.1.1 - - [06/Mar/2015:17:52:51 -0800] "GET /owncloud/ HTTP/1.1" 403 1002
192.168.1.1 - - [06/Mar/2015:17:52:53 -0800] "GET /owncloud/ HTTP/1.1" 403 1002
$ ls -al /usr/share/webapps/
drwxr-xr-x 5 root root 4096 Mar 6 17:12 .
drwxr-xr-x 165 root root 4096 Mar 6 21:22 ..
drwxr-xr-x 4 http http 4096 Mar 6 17:49 owncloud
drwxr-xr-x 10 root root 4096 Mar 5 02:11 phpMyAdmin
drwxr-xr-x 6 root root 4096 Sep 18 09:08 php-xcache
Also keep in mind that I've installed owncloud using the source downloaded from the website. I previously installed using the pacman, but wanted to configure it to be under a sub directory and not as my web root.
Last edited by johan1391 (2015-03-07 19:03:19) -
The system is not reachable, the login data could not be considered
Hello
I'm trying to connect via Hana Studio to a Hana One instance I have configured in AWS, following the guides & videos in the Hana Academy.
When adding the system in Hana studio, I get an error message after inputting the SYSTEM password:
The system is not reachable, the login data could not be considered
I've seen another post in the forum where the user solved the issue by resetting the SYSTEM password to a password without special characters, but mine is already "special character" free.
Are there others who have had difficulties when adding a new system?
Regards
YannHi Swapan,
Thank you for your attention and message.
I downloaded the SAP HANA Studio from "Get your own SAP HANA, developer edition on Amazon Web Services (http://scn.sap.com/docs/DOC-28294)", specifically at SAP HANA Studio, developer edition and SAP HANA Client, developer edition, for Windows XP 32-bit. Is this HANA One? How to know the version of HANA server? How to make my Internet or firewall allow me to go out to the JDBC port? I am just learning to deal with these computer-science issues.
Regards,
Beiwei
Date: Wed, 4 Sep 2013 20:52:41 -0700
From: [email protected]
To: [email protected]
Subject: Re: - The system is not reachable, the login data could not be considered
SAP HANA
The system is not reachable, the login data could not be considered
created by Swapan Saha in SAP HANA One Platform on AWS - View the full discussion
Hi Beiwei,
I suppose you are using HANA One (which you can only launch today from AWS Marketplace and HANA costs 99 cents/hr). If it is HANA One, which version of HANA One you are using? Please make sure you are using the same version of HANA Studio with HANA Server? Instance number in HANA One is 00.
If you HANA One, by default, it will open all the necessary ports. Please make sure you are Internet or your firewall allow you to go out to the JDBC port. If not, you cannot connect your studio behind your firewall with HANA server in the cloud.
Thanks,
Swapan
Reply to this message by replying to this email -or- go to the message on SAP HANA
Start a new discussion in SAP HANA One Platform on AWS by email or at SAP HANA -
Officejet Pro X476dw MFP not reachable
Hi,
out of the blue my Officejet Pro X476dw MFP turned 'not reachable' from my MacBook. Device is still connected to my Wifi network, no changes there since last use. I can print ok from my iPhone. I turned the device off and on again - no success. I turned the MacBook off and on again - same. I reconfiguered Wifi connection at device - same. I deleted printer from MacBook and tried to re-add but installation program couldn't find device. I tried to connect manually using IP address that was shown on device - 'device not reachable'.
I am running out of ideas, appreciate any help!
Thank you!
Maik.@weirdharrell
Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP -
Hello,
we've configured a UC560 with Cisco Standards. So the CUE has the IP-adress 10.1.10.1 (Gateway .2).
The CUE successfully answer a ping ! The CCA CUE diagnostics ended successful.
I also can connect to CUE through CLI of the UC560.
BUT : The Webinterface of the CUE does not answer. The webiste ist not reachable.
Here the http config of the UC560 :
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/GUI
telephony-service
video
fxo hook-flash
max-ephones 138
max-dn 600
ip source-address 10.1.1.1 port 2000
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message Cisco Small Business
url services
http://10.1.10.1/voiceview/common/login.do
url authentication
http://10.1.10.1/voiceview/authentication/authenticate.do
cnf-file location flash:
cnf-file perphone
user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
network-locale U4
load 7941 SCCP41.9-1-1SR1S
load 7941GE SCCP41.9-1-1SR1S
load 7961 SCCP41.9-1-1SR1S
load 7961GE SCCP41.9-1-1SR1S
load 521G-524G cp524g-8-1-17
time-zone 23
time-format 24
date-format dd-mm-yy
dialplan-pattern 1 5909.. extension-length 2
keepalive 30 auxiliary 4
voicemail 39
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$xdzm$dQ00q0.IUYeRDA4lTuNIl1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
transfer-pattern 6.. blind
secondary-dialtone 0
and the telephony part :
telephony-service
video
fxo hook-flash
max-ephones 138
max-dn 600
ip source-address 10.1.1.1 port 2000
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message Cisco Small Business
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.1/voiceview/authentication/authenticate.do
cnf-file location flash:
cnf-file perphone
user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
network-locale U4
load 7941 SCCP41.9-1-1SR1S
load 7941GE SCCP41.9-1-1SR1S
load 7961 SCCP41.9-1-1SR1S
load 7961GE SCCP41.9-1-1SR1S
load 521G-524G cp524g-8-1-17
time-zone 23
time-format 24
date-format dd-mm-yy
dialplan-pattern 1 5909.. extension-length 2
keepalive 30 auxiliary 4
voicemail 39
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$xdzm$dQ00q0.IUYeRDA4lTuNIl1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
transfer-pattern 6.. blind
secondary-dialtone 0
Can the problem be based on corrupt http CUE files or the wrong version ? Which files are required ?
May the Firewall ACLs block this traffic ? But ping works !
Please help !
Greets
HuckThat usually happens when your PC is using a default gatway that doesn't know about CUE address subnet.
So you have to fix your routing. -
ADAWS Webapp Directory Does Not Exist
Hello,
When I do the test (Security Settings) by the URL http://localhost/adaws/install/writeFiles.aspx I have the following error: "ADAWS Webapp Directory Does Not Exist."
Someone knows what are happening?Tech support told me:<br><br>
"We have bug #60365 filed on this issue. The version number in WriteFiles.asp.vb is hardcoded to '6.2' and It will look through pthome.xml for this version of ID-AD and not find it. As a result, it will throw the 'Directory Does Not Exist' error. "<br><br>
Basically, just ignore the diagnostic error as the remainder of the app is unaffected by it. -
PowerShell script : Directory object not found error in Get-ADGroupMember
I am new in powershell scripting. I am writing a script to add users in different AD Groups. while doing so I do the following:
Check if the user already exist in the group:
$mbr_exist = Get-ADGroupMember $grpname | Where-Object {$_.SamAccountName -eq $sam}
If user does not exist then add the user to the group.
When I manually run the script its runs flawless, without any errors. But when I schedule the script to run it gives an error as follows:
3/30/2015 8:32:15 AM Directory object not foundAt + $mbr_exist = Get-ADGroupMember $grpname | Where-Object {$_.SamAc ... + ~~~~~~~~~~~~~~~~~~~~~~~~~~ Error at Line:$mbr_exist = Get-ADGroupMember
$grpname | Where-Object {$_.SamAccountName -eq $sam}
The strange thing is the user for which it throws the error is present in the group.I am not sure why this error is occurring when scheduled. Can any one please help? All the suggestions will be appreciated
Note: (The script is scheduled using Windows Task Scheduler)
try
# # Initialize the variables we will use
$status = 'false'
$drivename = "H:"
$sysdate = Get-Date -UFormat "%m_%d_%Y"
$foldername = $drivename + "\Script_Result\PowershellData"+ $sysdate
$backup_folder = "$foldername\AD_Groups_Backup"
$updatedGroup = "$foldername\Updated_AD_Groups_LogFiles"
$LogFilePath = "$foldername\Log_Update_ADGroups"+$sysdate+".log"
# # Initialize the arrays we will use
$GroupArray = @()
# # maintain log of program startup
$logdate = get-date
$logdate.ToString() + "`tStarted script to Update AD user Groups..." | Out-File -FilePath $LogFilePath
# # Create a sub folder to store the backup files
$fileexist = Test-Path $backup_folder -PathType Container
if($fileexist -ne 'False')
New-Item -ItemType Directory $backup_folder
# # Create a sub folder to store Updated AD group Log files
$fileexist = Test-Path $updatedGroup -PathType Container
if($fileexist -ne 'False')
New-Item -ItemType Directory $updatedGroup
# # Take back up of the AD groups data
Get-ADGroupMember -Identity "Group1" | Export-csv "$backup_folder\Group1_BackUP$sysdate.csv"
Get-ADGroupMember -Identity "Group2" | Export-csv "$backup_folder\Group1_BackUP$sysdate.csv"
Get-ADGroupMember -Identity "Group3" | Export-csv "$backup_folder\Group1_BackUP$sysdate.csv"
Get-ADGroupMember -Identity "Group4" | Export-csv "$backup_folder\Group1_BackUP$sysdate.csv"
(an so on..... 11 such groups )
# # Fetch AD Users data
$ADusers = Get-ADUser -filter {(EmployeeNumber -gt 1) -and (EmployeeNumber -ne "N/A") -and (Enabled -eq $true)} -Properties * | Sort-Object -Property EmployeeNumber
$ADusers.Count
foreach($u in $ADusers)
$sam = $u.SamAccountName
$empnum = $u.EmployeeNumber
$mgr = $u.mgr
$fsal = $u.'fsalary-Hourly'
$comp = $u.Company
$ofc = $u.Office
Write-Host "$sam : $empnum : $mgr :$fsal : $comp : $ofc" -ForegroundColor Yellow
$GroupArray = @()
# # Check if the user fits in any of the 11 scenarios
if($comp -eq "US")
# scenario 7
write-host "7. Add to US Employees"
$GroupArray += "US Employees"
if($mgr -eq "Y")
Write-Host "1. ADD to US MAnagers"
$group = "US Managers"
$GroupArray += $group
if(($fsal -eq "Hourly") -and ($ofc -ne "Canton"))
Write-Host "3. Add to US Hourly (excluding Canton)"
$group = "US Hourly (excluding Canton)"
$GroupArray += $group
if(($fsal -eq "Hourly") -and ($ofc -eq "Canton"))
write-host "4. Add to US Canton Hourly"
$group = "US Canton Hourly"
$GroupArray += $group
if(($fsal -eq "Salaried") -and ($ofc -eq "Corporate" -or $ofc -eq "Landis Lakes 1" -or $ofc -eq "Landis Lakes 2"))
Write-Host "5. Add to US Salaried Corporate"
$group = "US Salaried Corporate"
$GroupArray += $group
if(($fsal -eq "Salaried") -and ($ofc -ne "Corporate" -and $ofc -ne "Landis Lakes 1" -and $ofc -ne "Landis Lakes 2"))
Write-Host "6. Add to US Salaried Plant"
$group = "US Salaried Plant"
$GroupArray +=$group
elseif($comp -eq "canada")
# scenario 9
write-host "9. Canada Employees"
$GroupArray += "Canada Employees"
if($mgr -eq "Y")
Write-Host "2. Add to Canada Managers"
$group = "Canada Managers"
$GroupArray += $group
if($fsal -eq "Hourly")
Write-Host "10. Add to Canada Hourly"
$group = "Canada Hourly"
$GroupArray += $group
if($fsal -eq "Salaried")
Write-Host "11. Add to Canada Salaried Plant"
$group = "Canada Salaried Plant"
$GroupArray += $group
elseif($ofc -eq "Corporate" -or $ofc -eq "Landis Lakes 1" -or $ofc -eq "Landis Lakes 2")
Write-Host "8. Add to Corporate Employees"
$GroupArray += "Corporate Employees"
write-host "Final Group List" -ForegroundColor Green
$grplen = $GroupArray.Length
#$GroupArray
$grplen
for($i= 0; $i -lt $grplen; $i++)
$grpname = $GroupArray[$i]
write-host "$sam will be added to Group : $grpname" -ForegroundColor Magenta
# # Check if the user is already present in the Group
$mbr_exist = Get-ADGroupMember $grpname | Where-Object {$_.SamAccountName -eq $sam}
if($mbr_exist -eq $null)
# #Add user to US Managers group
Add-ADGroupMember -Identity $grpname -Members $sam
Write-Host "1. User $sam is added to $grpname group" -ForegroundColor Green
# # documenting the user list that are added to this group
$grpmbr = New-Object PSObject
$grpmbr | Add-Member -MemberType NoteProperty -Name "EmployeeNumber" -Value $empnum
$grpmbr | Add-Member -MemberType NoteProperty -Name "SamAccountName" -Value $sam
$grpmbr | Add-Member -MemberType NoteProperty -Name "Name" -Value $u.Name
$grpmbr | Add-Member -MemberType NoteProperty -Name "DistinguishedName" -Value $u.DistinguishedName
$grpmbr | Add-Member -MemberType NoteProperty -Name "mgr" -Value $mgr
$grpmbr | Add-Member -MemberType NoteProperty -Name "Company" -Value $comp
$grpmbr | Add-Member -MemberType NoteProperty -Name "Salary/Hourly" -Value $fsal
$grpmbr | Add-Member -MemberType NoteProperty -Name "Office" -Value $ofc
$grpmbr | Add-Member -MemberType NoteProperty -Name "ADGroup" -Value $grpname
$grpmbr | Export-Csv "$updatedGroup\ADUsers_To_Group($grpname)_$sysdate.csv" -Append -NoTypeInformation
else
Write-Host "Member $sam already exist in $grpname group" -ForegroundColor Red
$logdate = get-date
$logdate.ToString() + "`tCompleted script to Update Update AD Groups..." | Out-File -FilePath $LogFilePath -Append
$status = 'true'
return $status
catch
$err_lineno = $error[0].InvocationInfo.ScriptLineNumber
$err_line = $error[0].InvocationInfo.Line
$ExceptionMessage = $_.Exception.Message
#$ExceptionMessage
$error_info = $error[0].ToString() + $error[0].InvocationInfo.PositionMessage
Write-Host "$error_info " -ForegroundColor Red
$FailedItem = $_.Exception.ItemName
if($ExceptionMessage)
$logdate.ToString() + "`t $error_info " | out-file "$foldername\ErrorLog_Update_AD_Groups$sysdate.log" -append
"Line Number: $err_lineno . `nError at Line: $err_line" | out-file "$foldername\ErrorLog_Update_AD_Groups$sysdate.log" -append
#Invoke-Item "C:\ErrorLog.log"
$status = 'false'
return $statusHi mdkelly, Sorry for such a late reply (due to credential issues).
I am using Windows task scheduler to schedule the task. I am given the administrator access to the server (Windows Server 2012). So I think I set to run the script under system account.
My apologies for asking this, am I missing something while scheduling the script through task scheduler? how to check if the scheduled task is running under who's credentials? How to pass my (admin) credentials, so that the script execution won't face
a problem? Any suggestion on the above questions will be helpful. (I tried to search on net for the questions but didn't get any conclusive answers)
Thanks in advance. -
Ise node is not reachable after upgrading 1.2
Hi, I was using beta version of ISE with 1.2.834 code. and now the official release came out so I upgraded it.
after that, the ISE is not communicating with AD, and when I go to download logs, It says node is not reachable even though it is STANDALONE mode.
does anyone know how to work around this ?
should I just delete everything and go from scratch ?The ISE is not communicating to the AD, So, you have to rejoin the domain. For this purpose please follow the following actions:
Go to Administration > Identity Management > External Identity Stores and select Active Directory from the left-hand pane.
Click Join at the bottom of the configuration page:
Also please check the LDAP port -
Massive modification of "Calling Search Space" under "Directory Number Configuration".
Hi all,
I have a question in order to modify in a massive manner the field "Calling Search Space" inside of the option "Directory Number Configuration".
There are a lot of phones that doesn't have the correct CSS, and I need to change it, but are aprox. 500 phones...
Is there any form that I can accomplish the task in a massive form? May be doing a query or uploading a CSV file??
Thanks in advance for your help.Hi Carlo,
I've tried your steps, but when I search for the extensions to modify, the checkbox doesn´t appear near of the result of any extension
the option just show me the extension list an some other information but not anymore.
Is there any option that I need to enable inside of CUCM??
Also the version of CUCM that we are using is 9.1.
Thanks for your help -
Hi Everyone,
I'm very new to WebLogic, so I apologize if this is a dumb question.
I'm trying to install WebLogic as server for OBIEE. My environment is pretty simple. I have two Oracle Red Hat Linux 32-bit physical machines, let's call them WLS_SERVER and OBIEE_SERVER. I installed OBIEE on the OBIEE_SERVER and tested it using the out of the box OC4J container and that worked fine.
Then I installed WebLogic 11g on the WLS_SERVER machine and I ran the config.sh script. I used the configuration GUI to register the two physical machines and an additional server object called BIServer. Out of the box, web logic comes with AdminServer server object. I heard it's a bad practice to deploy applications to the AdminServer, hence why I created the BIServer object. I associated BIServer with the OBIEE_SERVER machine.
I went to start the BIServer and I got the following error:
"For server BIServer, the Node Manager associated with machine OBIEE_SERVER is not reachable."
How do I setup a Node Manager on the OBIEE_SERVER? Do I also need to physical put the WebLogic install file on the OBIEE_SERVER box and also run the installer there? Or there a copy paste thing I do? What am I missing here?
I appreciate the help!
-JoeI'm trying to install WebLogic as server for OBIEEI have not heard about OBIEE, but if your aim is to use weblogic as a server for hosting this then you definitely need to install weblogic on the physical box where OBIEE will be hosted.
I associated BIServer with the OBIEE_SERVER machine.
I went to start the BIServer and I got the following error:
"For server BIServer, the Node Manager associated with machine OBIEE_SERVER is not reachable."Again not sure what is BIServer but I think you are missing a number of steps here. If you are trying to run BIServer
on weblogic you definitely need to install WLS on this physical machine [OBIEE_SERVER]. You will then need to configure a node manager on OBIEE_SERVER machine to enable it to start remotely from the admin machine.
Link for Node Manager. Since you are in Linux you can try setting up script based node manager.
http://download.oracle.com/docs/cd/E13222_01/wls/docs92/server_start/nodemgr.html#wp1099239 -
I AM FACING PROBLEM AFTER UPDATING (7.0.4) MY PHONE MODEL 5C,AFTER THIS UPDATE SOME TIMES I CANT MAKE CALLS & SOME TIMES WHEN ANY BODY ELSE WANTS TO CALL ME BACK THE MESSAGE COME THAT THE USER IS NOT REACHABLE.PLS HELP
I am facing the same issue! I bought 5c few days back
and everything was fine till I updated the software 7.0.4!
Whenever am connected to wifi am unable to make a call and if someone tries
Calling me they get the message that my number is not
Reachable! When I go back to 3G the calls work perfectly!!
Please help me out since I use wifi more than my network.
Appreciate any advise on this -
Change directory number on 7960
Hi there,
I need to edit the directory number of a 7960 phone to 0009 but can't even get to the page that allows the change. Please help!!!
Thanks...
LisaHi Lisa,
From ccmadmin;
Updating a Directory Number
Follow these instructions to update a directory number that is assigned to a specific phone.
Procedure
Step 1 Choose Device > Phone.
The Find and List Phones window displays.
Step 2 Enter search criteria to locate a specific phone.
A list of phones that match the search criteria displays.
Step 3 Click the name of the phone to update.
The Phone Configuration window displays.
Step 4 From the Directory Numbers list, click the line that you want to update.(Probably Line 1)
The Directory Number Configuration window displays.
Step 5 Update the appropriate settings (Directory Number in this case to 0009)
Step 6 Click Update.
Step 7 The change gets automatically applied to the phone after you click OK; however you can click Reset Devices. For more information, see the "Resetting a Phone" section.
Note: Devices restart as soon as possible. During this process, Cisco CallManager may drop calls on gateways.
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00803ed74c.html#wp1019899
Hope this helps!
Rob
Maybe you are looking for
-
Running Photoshop CS 6 on my Windows 7 desktop and now I just purchased a Mac Pro laptop
I just purchased a Mac Pro laptop and would like to run Photoshop CS 6 I currently am using my desktop which is Windows 7 what is the best way to purchase a license for my laptop
-
Bridge won't run. Should I reinstall it?
1.I went to Windows>Workspace, and "Output" was not there. 2. I read at adobe.com help that I should check for updates and then download the "Output" workspace, then put it at the right extension. 3. I did that. 4. Now Bridge won't start. It doesn't
-
Transferring apps from 3g phone to 4 phone
I just updated from an iPhone 3G to the iPhone4 and want to transfer my apps to the new phone, I was told at Best Buy when I bought it that this wasnt possible...is that true and if I can transfer how do I do it?
-
Can anyone tell me how to retrieve all reserved identifiers and keywords in
can anyone tell me how to retrieve all reserved identifiers and keywords in oracle ??? i want to know the syntax of query ??
-
Does anyone know how to reinstall quicktime on an older g-5 running 10.4.11
i was getting error-50 after updating safari/firefox and most wmv files would not open. i deleted quicktime , emptied it from trash, did a restart, and tried to reinstall several versions of quicktime from apple with zero luck ... anyone out there kn