MWI does not work on Cisco IP Phones using VG248
Hi,
We are facing issue with MWI on/off using SMDI connectivity to FCS voicemail system with Cisco Callmanager (6.1.x). Below is the connectivity.
CUCM ver 6.1.4---->VG248 ver 1.3.1 (SMDI and Asyc1) ----> FCS
We are able to receive and send voicemails on the IP Phones but the light never lit. I verified the MWI numbers on CUCM/VG248 and FCS voicemail system, rebooted all the appliances with no luck.
So if have the port numbers with you for Sonos multiroom-system then you can do the port forwarding and follow the steps:-
First of all get your Device IP address for which you want to do the Port Forwarding...
Then open the router's setup page click on the Applications and Gaming Tab and then click on the sub tab Port Forwarding then open the ports that you want...
Refer the link : http://media.photobucket.com/image/XBOX%20360%20NAT%20issues/EricScpoc/linksys_setup.png
Then logout from your Router's setup page.. Unplug your Router from the power, wait 30 seconds. Then plug in the Router again.
Try out these settings it will help you out...
Similar Messages
-
I have just downloaded Yosemite but I find that Photoshop Elements 11 does not work properly. If I use a tool like a paint brush or spot healer I cannot paint a full stroke does anyone else have this issue or know a solution?
Many thanks that does work. But it now leads to another question is this simply a trackpad issue and if so will it be fixed? I use Elements every day and was thinking I would have to go back to Mavericks.
-
I have just updated my iPhone to version 5.1. After the update, the camera button next to the "slide to unlock" button does not work at all. It used to function well before the update. It happens to my friends as well. What should I do? Can someone help?? Thanks!!!!
Slide the camera button up
-
my iphone 4 lock button does not work, i turned it off using assesive touch, now it wont turn back on? got any tips for fixing this problem!
Hi, braidenwhitesidemate.
Thank you for visiting Apple Support Communities.
I would recommend going through the steps in the article below. If the issue persists, see the section labeled Issue not resolved.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Cheers,
Jason H. -
Hello this is my first post on cisco support and hope I can get some help. I recently purchased the book CISCO CCENT / CCNA ICND1 by wendell odom and when I used the CD to install the Pearson Practice exams, it does not work. I tried everything! It even asks for a activation code, which on the CD It says "Refer to the Activation Code Included in the DVD Sleeve when Registering Pearson IT Certification Practice Test Software"I don't see anything related to a Activation Code anywhere on the CD OR on the sleeve! So now I can't use that.
The Network simulator Wendell odom uses in his videos is already outdated it seems and I can't get mine to work. Why? Because I bought this book in hopes of this being a beginner book and praying the person won't skip information to actually set up the book. So now the videos are useless because I can't connect because I have no idea how...
The Network Simulator lite, wow 3/3 When giving me software to use. The Prompt command does not work, Only the enter key will work but when I try to put in a password I can't hit anything else but enter.
I hope I can get help from a more official member as to seeing how I bought this book and I can read but whats really the point if I don't have the hands on training?Keunepete,
When I ordered my books for the ICND1 and ICND2, they came with a CD in the back pocket (sleeve) of the book. Along with the CD was a thick piece of paper that had the activation code on it. It was a white, square piece of paper with big black print on it. Did you buy your book used? Was the CD sealed in the back pocket?
-Zach -
Date parameter does not work in SharePoint 2010 report using SQL 2008 Server Reporting Service
Here is the settings:
SharePoint 2010 with SQL server 2008 reporting services configured
When create a report for a SP list using SQL server report builder (3.0) the date parameter does not work.
The data parameter is set as "date and time" type and field name equals the col name in the SP list
When run the report, the whatever dates I select, the result is always the same, so the parameters do not take any effect.
Is any step missing?
Thanks for any advice !Hi ,
How did you configure you "date and time" type parameter and field name equals the col name in the SP list?
Have you tested if other type parameter worked?
Have you tried typing the date format as 20140722 in your date parameter filed before run the report?
http://whitepages.unlimitedviz.com/2012/02/using-sharepoint-filters-with-reporting-services-parameters-for-personalized-reports/
Thanks,
Daniel Yang
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Daniel Yang
TechNet Community Support -
Lion Install does not work, says "This disk is used for Time Machine backups"
I'm having trouble installing Lion onto my macbook pro intel core 2 duo.
I am backing up my computer with an external drive using TimeMachine, but i've disconnected it. Also i'm running SL 10.6.8
I have a windows 7 partition that was created with boot camp.
I've tried to make sure everything is all ready for lion but when I go to install lion it says "This disk is used for Time Machine backups" and the hard drive is grayed out.
Same problem as this guy: https://discussions.apple.com/thread/3190321?start=0&tstart=0
I'm hearing that a file called "Backups.backupdb" is on the top level of the hard drive, but I see no such file. I've looked at the invisible files and I cant find it.
I've also created a bootable flash copy of the lion install but that does not work It gives me the same message "This disk is used for time Machine backups"."Backups.backupdb" if the file in Time Machine. As the discussion says, you have to find that file and trash it. Try spotlight to locate it. If that does not work, down load OmniDiskSweeper from the Internet (free) and go through an organized search to find "Backups.backupdb". If that takes too long or is too tedious, then if you have everything backed up, erase the HDD and start from square one.
Ciao. -
I have a main.jsp, and in this main.jsp, I have two part, leftButton.jsp and view.jsp, I want to include the leftButton.jsp and view.jsp to main.jsp.
The code of main.jsp is like follows:
<%@ page language="java" contentType="text/html" %>
<html>
<head>
<title>JSP include element test</title>
</head>
<body>
<table>
<tr>
<td><jsp: include page="leftButton.jsp" flush="true"></jsp: include></td>
<td> <jsp: include page="view.jsp" flush="true"></jsp: include></td>
</tr>
</table>
</body>
</html>
Why the include does not works? by the way, I embeded a flash.swf file in view.jsp.Hi Mellon,
You might be better off using a JSPF segment for leftButton.jsp & view.jsp and the <%@ include file="relativeURL" %>.
Be careful that the included file does not contain <html>, </html>, <body>, or </body> tags. Because the entire content of the included file is added to the including JSP page, these tags would conflict with the same tags in the including JSP page, causing an error.
Note: It is conventional to put JSP segements under the WEB-INF/jspf/ folder so the file cannot be accessed directly by a URL
Note: JSPF files end with .jspf, so your files would be leftButton.jspf and view.jspf. -
I took my Bionic back to Verizon yesterday. I am not getting 4G data, and it will not work in the car dock. When I got to the store, I had 4G, and it worked perfectly in the dock, all he did was sit it in. This phone must only work in the store, maybe that is why they released it before it was ready.
The Verizon technician told me that there were problems with the phone, but that the responsibility belonged to Motorola. He said there was going to be an update in November and that I should wait. This concerns me because it means Verizon will pass the buck on this one.
What choice do I have? My return period is way over. I am paying for a service that I don't have yet I can't get out of it. If the phone can't be fixed by a software update, then what? At that point, I will either hope for a class action suite, or cancel my contract and pay $350 so that I can get a decent phone....iPhone from AT&T. That would be cheaper than buying a new phone from Verizon under my current contract. I can't keep a phone that never works.
I think yesterday was like the straw that broke the camel's back for me. I tried for 15 min to get the car dock to work, and nothing would turn it on. That is when I just drove to Verizon. I figured they should see one more unhappy customer in person instead of just online...alas, no one there gave a **bleep** and they are still trying to sell the Bionic to the unsuspecting customer. It should be pulled off of the shelf until it is fixed.
Joeytechwhiz wrote:
Verizon and Motorola didn't have the time to test the Bionic.
They were too busy working on the Razr and screwing us.
PRE-ORDER YOUR DROID RAZR TOMORROW 10.27 8AM EDT
Introducing DROID RAZR by Motorola.
The ultimate power of DROID. The legendary edge of RAZR. Combined to form the world's thinnest 4G LTE smartphone.
• Android 2.3 Gingerbread OS
• Dual-core 1.2 GHz processor
• KEVLAR® strong back plate, Gorilla® Glass face
• 7.1 mm thin with big 4.3 inch Super AMOLED Advanced display
My Bionic did it again. It is not recognizing the car dock, and it is not getting data connection. I sat in a La Madelains for 15 min hoping for data. Then, when I drove home, I tried the car dock...nothing. This is basically a little 3G tablet with WiFi and a phone. I can do most of that better with my iPad.
Joey -
DHCP Server does not work after Exporting and Importing Using Netsh Command
Hello Friends :
I had two dhcp servers in windows server 2003 server , I have upgraded one of them to windows server 2008 32 bit and again i installed a windows server 2008 R2 as an additional Domain Controller , the last scenario was like this :
srv-1 : windows server 2003 + DHCP = working with no problem
srv-2 : windows server 2003 + DC + DHCP = Worked without problem
srv-3 : windows server 2008 R2 + DC = worked without any problems
I exported the DHCP server configuration on the srv-2 using netsh dhcp server export and Imported them to srv-3 using the
netsh dhcp server import command , the command completed successfully and i can see all of the scopes without any problems and errors , i have authorized the new server without any problem , all scopes are activated without any problem so i
disabled the srv-2 DHCP service and unauthorized it from active directory , the problem is that the new server semms that does not lease any address to clients !!!
1- I have authorized it
2- I used Rogue Checker tool in client computers they see authorized server without any problems
3- The same tool in workgroup only shows srv-1 as the DHCP server and does not see other DHCP servers
4- Bindings are OK and DHCP servers only have one NIC installed on them
What can i do to make sure my srv-3 DHCP server will work on the network ?
thanks ...
MIMOAre the clients on another network so you need to configure a DHCP relay agent?
If you load up perfmon on the dhcp server and remove all counters and then add DHCP counters. Do you see any dhcprequests when you reboot your dhcp clients? This will determine if your server actually receives any dhcp requests.
Have you check event viewer for any warnings or errors?
And the classic one restarted the dhcp server service (or reboot)?
Regards Per-Torben Sørensen http://pertorben.wordpress.com/ -
I brought my Iphone on the At and T site 3 months ago and it's not working how can I have it repaired?
I think that you should just contact the place you bought it from and have them take a look at it, and if you have the warrenty on your iPod you can get a new replacement too.
-
I upgraded to iso7 and my passcode that I just entered during setup willnot work, phone is disabled!! I cannot even turn it off!! I don't want to lose all my info!! HELP!!!!!!!!!!
http://support.apple.com/kb/HT1212
-
please need help need to reset my iphoe but power button is broken and on a new computer. what do i do
You can also make a Genius Bar appointment at your nearest Apple Store and have it replaced under your warranty.
-
The lasso tools worked great before i upgraded to Yosemite.. Some one please help.
I have the same problems. There are not answers anywhere.
-
i have read ur forgotten password or device disabled after entering wrong password. iphone is desabled dont have computer i conected it to before and power button is broke so how can i get back into my iphone?
You will have to restore the phone and set up as New. See: http://support.apple.com/kb/HT1212. The part you need is near the bottom, "If you have never synced your device with iTunes...". You will lose any content that is not backed up in iCloud.
Maybe you are looking for
-
Need Help Putting Together a rMBP so I Have Everything I Need...
Hello- I am having trouble getting the right kind of help from "Chat Now" on apple.com and calling in to get my questions/needs taken care of so that when I get the rMBP I will be sure I wil have what I need to go right online and teach the online co
-
Speak selection don't work in all text apps
speak selection don't work in all apps use text is example pictures with text apps the first 1 is the e-mail app you can see the speak selection bar. in there and the second app is the kik app you can only see the copy bar. only is a away to turn it
-
Please recomend a good book to create art in Photoshop?
I want to learn to create menus and artwork in photoshop and Illustrator. I have seen many books but they tend to work with manipulating photographs. I want to create pictures and menus.... Can anyone recommend a good book (available in UK) to teach
-
Error: "client-error-request-value-too-long" when trying to add printer
After installing the 10.4.9 Combo update, my HP 1350 All-in-One printer was not recognized. I reinstalled the driver, but now I can't add the printer. I get the error message "client-error-request-value-too-long" when trying to add the printer. Has a
-
I own a new iPad and a MacBook Pro. An Apple store assistant changed my Apple ID on my iPad, and the new ID showed up in the iCloud setting on the iPad. However on my Mac laptop the iCloud still shows my old ID, so there is no synching of documents g