My 2nd MSI Z77A-GD65 won't start

Hi,
this is my 2nd motherboard with the same symptom.
as you can see in the video, the motherboard starts for less than a second and stops.
*please note* the ticking sound is the relay sound which start another PSU.
The first mother i had used for about a week and after that it didn't work. I sent to supplier and wait about 4 weeks and got this one.
After got the new one, I updated the firmware as it didn't recognise my display card. (same procedure as the 1st mobo).
After it successfully updated. it doesn't start.
Could you please advice what was going on? How 2 'military class labelled' motherboards fail the same ?
CPU intel i5
Memory : G-Skill
PSU : Seasonic 80+

Quote from: PirateDog on 03-December-13, 06:58:35
How is it supposed to initiate if the 8-pin ATX/EPS power isn't connected?
as I mentioned,this was working before the failure happened. I disconnected the display adapter and that PSU pin to see if anything might work.
The motherboard's still not working as you can see in the video.

Similar Messages

Msi Z77A-GD65 Does't start at all

hello !
I got my msi Z77a-GD65 yesterday and a I5 2500k;I tried to see if they work.
1- i Discharged my self.
2-got the MB out of the box put it on the electrostatique bag and on the box.
3- i installed the cpu carefully and successfully.
4-installed the RAM (1 stick of g skill ripjaws x 1600mhz 2 gb) on DIMM1.
5-installed the intel heatsink
6-and an old power supply that used to perfectly power my old pc(PENTiUM4)
After that i turned on the power supply.Waited a few second and pressed the power onboard button.
the motherboard did not start the fan start to spin for1-2 seconds and turned off,the cpu phase led 1 was luminated for 1 second and then all 8 phases have just flashed and the motherboards retarted and heve been like thet ever since.also the LED debug just flashed and didn't write anything.
please help.
Also there is a julper named JSVID1 right by the VRM heatsink it is not mentionned on the manual what does it do?

Quote from: HU16E on 30-April-12, 06:17:28
Also recommend to get a quality +12V single rail PSU.
Get at least a 80 plus certificated power supply, that is for energy efficiency certification but also means quality (not always by some unreliable brands).
Dint knew that i could advice brands, some support forums are quite picky even if that isn't write in the rules. So here it goes, Corsair, Antec, CoolerMaster, Silverstone, Enermax, Seasonic, NZXT, XFX, Super Flower, FSP. All these are good and reliable Power Supply brands.
Now you only need to see how much watts you need for your system, this one is simpler to use http://www.corsair.com/learn_n_explore/?psu=yes, next one more accurate but a little more complex http://extreme.outervision.com/psucalculatorlite.jsp

MSI Z97-GD65 won't start

Hello,
so I bought Z97-GD65 motherboard, installed all components and when I try to turn it on, it does not start. Only the light on the motherboard's power button is blinking and nothing happens, no fan spins, no additional light come on. Tried with different PSU, replacing RAM, disconnecting other components and nothing helps.
So is my motherboard dead?
P.S. one stange thing, the BIOS battery was dead, checked with voltmeter, replaced with other, didn't help.
Specs:
Board: MSI Z97-GD65
VGA: Gigabyte 770GTX 4GB
PSU: Seasonic X-750 (62a 12v rail)
CPU: Intel i7 4770k
MEM: Crucial Ballistix 2x4GB 1600MHz
HDD: Samsung EVO 120GB SSD
HDD: Seagate Baraccuda 2TB
COOLER: Scythe Kotetsu

Quote from: Nichrome on 21-December-14, 01:53:41
Hi,
Please specify your computer, see >>Posting Guide<<
Did you try to boot outside of the case?
Sorry about that.
Haven't tried that, doing it now.

MSI Z68A-GD65 won't start to bios!

gratz from Finland guys.
I have problem, heres my pack:
MSI z68a-gd65
i5 3450
hyperx predator 8gb 2x4gb rams
asus gtx660 pci-e 2gb
2tb seagate
650w corsair
and the problem, i installed up the components today and got it working first without detecting SATA 2tb seagate. Then i switched to all sata ports and the last one 8 and 7 worked fine for seagate and Asus DVD. But now the problem is that it lets me in marvell bios when it shows up the harddisk and dvd, but not in the "primary bios". When it shows the first data, harddisk and dvd, it goes straight to "Warning BIOS ME file not found install on the usb" etc... I dont know what to do because i read all the forums in the internet, wasted 6 hours in investigating internet and found nothing. Have tried the flash utilitys, USB flasher utility found in forums and all... Reseting BIOS didnt help.
Please help, im getting drunk every hour more with this cra*

Sdrastvui Svet, jeshli s toboj realno 4eres skaip pogovorit, skin poshalushta svoj nick tam.
As i know, the board was in the warranty fix, and became back to shop, where i buyed it. But the shop gave everyone who would buy the board, 6months warranty so i dont think it would be broken.
Also for the flashing, i dont have OS on that system, what we are talking about. And if i download those BIOS from the MSI site, its only EXE? I cant run exe from USB flash when starting PC?

MSI Z77A-GD65 No Post

When I first started my new system, I did get a display and entered the BIOS. I changed the boot order to put my optical drive first, put in a live CD, restarted, and got a black screen. I ejected the CD, restarted, and got a black screen again. I didn't get a display again until I disconnected all my drives whereupon I got a map error and was able to get back into the BIOS. A web search indicated this is a bug that occurs when no drives are connected so I reconnected the drives, restarted, and got a black screen again. I disconnected the drives again and restarted but I got a black screen again (no map error this time). I tried connecting my monitor to the graphics card instead of the motherboard and that didn't work. I tried removing the graphics card and video capture card and that didn't work. I tried clearing the CMOS by pushing the button and even removing the battery for several minutes and that didn't work.
Here's where things get weird. I tried testing the RAM by pulling out one stick and the system kept restarting itself: it would turn on then power off a few seconds later then, after a few seconds, start up again, etc. I had to wait till it powered off and quickly pull out the power supply's cord to get it to stop. I removed that stick and put the other one in instead and the same endless loop of restarting happened again. When I put both sticks back in it stopped restarting.
Since I couldn't get into BIOS A, I switched to BIOS B and got a display again. There was no option to restore BIOS A so I was forced to continue using BIOS B. Since my graphics card was removed at this point, I changed the BIOS to IGD instead of PEG for graphics and shut down. I reconnected my drives then restarted and got a display again and entered the BIOS. I changed the boot order to put my optical drive first, put in a live CD, restarted, and got a black screen. I ejected the CD, restarted and got a black screen. I disconnected the drives and restarted hoping I would get a map error and could get back into the BIOS but got a black screen again. I've tried switching back to BIOS A but still can't get a display.
I tested the RAM by putting it in my old desktop one stick at a time, and then both sticks at once, and it worked fine. I installed the optical drive and one of the hard drives into my old desktop and successfully installed and booted linux off of it with the no problems. The second hard drive does appear to be borked and my old desktop froze when I tried to boot with that drive installed. However I've tried starting my new system multiple times without that damaged drive connected and I still get a black screen so I don't see how it could be the problem.
The LED on the motherboard mostly alternates between 19 and 72. It will run through a bunch of codes too quickly to read then pause for a second on 19 (Early South Bridge Initialization) then run through a bunch of codes too quickly to read then pause for a second on 72 (Late South Bridge Initialization) then go back to 19, etc. I've sometimes also seen it pause for a second on 55 (Early Memory Initialization) and 4F (which doesn't appear in the manual).
I'm guessing it has to be the motherboard or CPU but I don't know which. I don't have another motherboard to test the CPU on and no other CPU to test on this motherboard (the old desktop is AMD).
Hardware:
MSI Z77A-GD65 motherboard
Intel Core i5-3570K CPU
G.Skill DDR3-1600 CL9 1.5v 4096MB (x2) RAM (tested in old desktop)
Seagate Barracuda 1TB hard drive (tested in old desktop)
Pioneer BDR-208DBK blu-ray drive (tested in old desktop)
Corsair Obsidian 550D case
Seasonic G Series 550W power supply
Samsung S23B550V monitor (tested with old desktop)
Currently disconnected hardware:
HIS Radeon HD 7870 GHz Edition graphics card
Seagate Barracuda 3TB hard drive (believed to be broken)
Black Magic Design Intensity Pro capture card

Quote
Here's where things get weird. I tried testing the RAM by pulling out one stick and the system kept restarting itself: it would turn on then power off a few seconds later then, after a few seconds, start up again, etc. I had to wait till it powered off and quickly pull out the power supply's cord to get it to stop. I removed that stick and put the other one in instead and the same endless loop of restarting happened again. When I put both sticks back in it stopped restarting.
Test each stick in Dimm 2 (2nd from the cpu) Make sure they are installed into DIMMS 2 & 4 (2nd from cpu and last)
Did you try a full cmos clear on Bios A?
If so, you can recover using this guide:
https://forum-en.msi.com/index.php?topic=160450.0
With the z77a-gd65, you will need to flash bios B to version 10.5. In that version in the security section is a multi bios update. Use that and it will recover bios A.
For bios flashing: >>Use the MSI HQ Forum USB flasher<<

SOLUTION for my problems with MSI Z77A-GD65 + MSI N670 PE 2GD5/OC

Lately I had problems with my GTX 670 video card (MSI N670 PE 2GD5/OC) under Windows 7 Pro x64.
I got a lot of "Display driver stopped responding and has recovered" errors.
I had these errors once or twice a day, so I didn't really bother looking for an answer, also I couldn't reproduce the error.
Most games just worked fine, but not always... so I tried if I could reproduce the error.
I tried to stress test with MSI Kombustor and voila no windows error... noo... but the core voltage went to 0 mV within a minute and everything (screen / windows / kombustor) stuttered and I had to restart the system.
The strange thing was that the voltage went to 0 mV, but the GPU load went from 96% - 60% and back to 96%... why and how is this possible??
Now I could reproduce my problem... yes!
First I thought it was a driver problem, because I updated it to the newest version (310.70), so I tried to re-install an older driver and also the original MSI driver... no luck.
Maybe it could be a mainboard driver or some settings in windows, so I installed Windows 8... no luck.
Re-installed Windows 7 Pro x64 (basically because Windows 8 s*cks)... no luck.
I tried to put my video card in another system and there was no problem... so I thought my video card is not broken...
Maybe it's my my power supply... new power supply... no luck again... grrrr...
My solution was downgrading / flashing my mainboard (MSI Z77A-GD65) bios back to 1.5 instead of 1.7, because yes... live update had updated my bios... that was the problem.
I wanted to post this, because I couldn't really find the answer for my problem and maybe I can help a few people with the same configuration and problems.
Live well and... well you get the idea

Quote from: flobelix on 21-August-13, 04:12:05
Don't use TF II/TF III parts as they won't fit. Arctic Accelero Twin Turbo II or Accelero Mono PLUS are good value for money aftermarket solutions.
Thank you for the information and advice. As I was looking into those two, I noticed that Accelero's website claimed the Accelero Xtreme III would also fit, and NewEgg had it on sale, so that is what I wound up purchasing. It works quite well and is MUCH quieter than the Twin Frozr IV, even before the grinding noise started.
For anyone else considering this, please be aware that the Xtreme III is monstrously huge (it adds several inches to the length of the MSI N670 PE). Make sure you have plenty of room in your case for it.

Boot Loop Issues - MSI Z77A-GD65 - Solved

Picked myself up an MSI Z77A-GD65 as well as some Kingston 2x 4GB RAM sticks with a i5 2500k.
After getting everything installed, it just boot-loops on me showing me no boot menu, with a debug code of 55.
If I take out one of the RAM sticks and just use the #2 slot, it boots fine (but after starting windows, it flashes some blue screen and it boots again. I'm thinking that's only because I haven't installed any drivers and still have the old drivers from my motherboard. Yes/No?).
But as soon as I put the second stick in, it will not boot (swapped sticks and it boots fine with one stick). I've tried 1/3 and 2/4 and the only slot that seems to work is #2 (#4 slot won't boot with one stick in it). Tried each stick in each slot. 1/2 work, but 3/4 will not
I'm guessing this isn't a RAM issue but a MOBO issue? I sense an RMA in my future....

Quote from: XFM on 24-December-12, 08:29:56
Can you take a good quality, in focus hi-rez picture of the socket and post it so we can see what you are talking about?
I would if I could. Best way I can describe it is that the pins are all kind of bent at an angle (imagine an L shape, but upside down). Now take the bottom of the L (where it's small and turns) and kind of bend that facing the ceiling. It's kind of like that...
Quote from: Froggy Gremlin on 24-December-12, 08:30:08
Why is this thread in the Intel duo/quad section?
What are the amps on the PSU +12V rail(s)? And how old is it? Suggest to keep just the one RAM stick in the primary DIMM slot and do a fresh OS install with the Mode set to AHCI. BTW, what is the OS? 32 or 64 bit?
Good question. I think I was very tired/annoyed when I made this, and I guess I didn't look properly. If any mods can move it, or need me to take it down, I can.
PSU - http://www.newegg.com/Product/Product.aspx?Item=N82E16817703005
I don't have a problem doing a fresh install, but would like to make sure it's nothing else before hand. If I do a fresh install, and I still have to RMA the board, I would have to do another one to put all my old stuff back in, and I wouldn't really have a PC until the new board came (I mean I could still use it, but would have to re-install stuff and it seems like a bit of a pain if I don't *have to).
64-bit OS

MSI Z77A-GD65 going crazy after Windows 8/8.1 installation.

Hey so I decided to buy a new SSD and update my system to Windows 8.1 (coming from 7), mainly for optimal BF4 gaming experience, (I also intend buying a 290X lightning or two when they come out...) . But during the process I encountered a truckload of problems, my main one is this: I was using bios version 10.7 for almost a year, with a stable 4.8GHz OC (which I managed to get done after each bios flash since I built the rig in early 2012), everything went great - this was on Windows 7.
However when I migrated to Windows 8.1 my PC wouldn't boot anymore and after 5-6 attempts it did boot and it said that all my settings were reset to default, fine. I restarted and from then on it wouldn't boot anymore no matter what. The error code on the mobo is always "19" which in manual says it's Early South Bridge initialization. I have no ideea what to do anymore, I tried plugging out SSD, HDDs, GPUs, RAM sticks, clearing cmos with back panel button. It all boiled down to either not booting or going into a boot loop.
My only solution was to switch to bios B on the multi-bios switch which is running 10.2 an almost 2 years old bios. That beeing said I can boot normally now (and fast), and the system runs great but the bios version is so old that it does not let my 2x680 MSI Lightnings work in PCIE 3.0, only 2.0...
So i'm VERY scared of what to do next, because I don't want this second bios to corrupt as well.
I always flashed my bios with Live update 5, I did this with each new bios release and never had a problem but I read that the latest bios, 10.10 is buggy, and I don't know HOW to flash my bios to an earlier version, maybe even 10.7 or 10.8 in another way. Is there a way to safely flash BOTH bioses and to repair my A bios at the same time?
TL'DR, if there isn't any safe solution to my problem I might as well just press in OC Genie button and have a mild OC until sometimes next year when I'll get a new mb + cpu + ram anyway. But if there is one, please let me know.
Any imput is apreciated, THANKS!
full config:
CPU Model: Intel Core i7 3770K 3.5GHz| Corsair H100 push pull
Motherboard: MSI Z77A-GD65
Ram: 2x 4GB Kingston HyperX T1 Black Series DDR3 2133MHz CL11 Dual Channel Kit
Video Card: 2way SLI MSI GTX 680 Lightning 2GB DDR5 256-bit
Sound Card: Realtek ALC898
Storage: Corsair force GT 120 GB(OS) + 2x WD 1TB SATA-II 7200 RPM 32MB RE3 + WD 2TB SATA-III 7200RPM 64MB Caviar Black + WD 3TB SATA-III 64MB Caviar Green
Power Supply: Nexus RX-1.1K GOLD @ 1100W
Case: Cooler Master Storm Trooper + 8x Cooler Master SickleFlow 120 Red LED + Fan controller Scythe Kaze Master Pro black = negative pressure
Keyboard: Cooler Master Storm Trigger
Mouse: Cooler Master Storm Sentinel Advance II
CD/DVD: Asus DVD drive black
Monitor: Dell U2711 REVA07 IPS
Speakers: Logitech Z-5500
OS: Windows 8.1 Pro 64bit

I just found a post of mine (from another forum) from when the error 19 thing first started, this is what happend:
Quote
I decided to buy a new SSD and update my system to Windows 8.1 (coming from 7). And I encountered a truckload of problems, my main one is this: I was using bios version 10.7 for almost a year, with a nice 4.8GHz OC stable, everything went great - this was on Windows 7.
However when I migrated to Windows 8.1 my PC wouldn't boot anymore and after 5-6 attempts it did boot and it said that all my settings were reset to default, fine. I restarted and from then on it wouldn't boot anymore no matter what. The error code on the mobo is always "19" which in manual says it's Early South Bridge initialization. I have no ideea what to do anymore, I tried plugging out SSD, HDDs, GPUs, RAM sticks, clearing cmos with back panel button. It all bolied down to either not booting or going into a boot loop.
My only solution was to switch to bios B on the multi-bios switch which is running 10.2 that is almost 2 years old. That beeing said I can boot normally now, but the bios version is so old...
As you can see it had nothing to do with me doing a bad BIOS flash, actually not even the OC... isn't there perhaps a way to fix that A BIOS?

Error 55 Msi Z77A-GD65 Gaming

Hi guys,
I'm new in this forum..
I bought a new mainboard this is: MSI Z77A-GD65 Gaming.
My components are:
Intel i5 3570K
Asus Geforce 660 2GB
Ram Kingston Hyperx 2x4GB 1866Hz
The problem is, when i started for the first time the PC i read in the display "Error 55", I tried with the RAM in dual channel (1:2)(1:3)(2:4)(3:4) and in single channel with only 1 ram.
What I can do now?Have you already reported this problem? I can't even get into the bios, in practice, I was not able to turn it on the PC.
For more info you can contact me. Thanks and let me know as soon as possible pls.

Do >>Clear CMOS Guide<< with power cord removed, if no change, try with another and different type of RAM.
consult with memory support test list from msi web page

[SOLVED] motherboard MSI Z77A-GD65 error code B2

hello,
I recently installed an MSI Z77A-GD65.
Here is my config:
- MSI Z77A-GD65
- I5 2500K + Noctua NH U12P-SE2
- KINGSTON Hyper X 1600 Mhz DDR3 4 x 2 GB
- 2 x SSD VERTEX 3 and 4
- POV GTX 660 Ultra Charged 2 go
- WD Caviar 500 GB
- Supply CORSAIR GAMING GS 600
- Case CM HAF932 advanced
I searched all the forums I have not found anything on my problem is the following.
at the first start (after installing the hardware) I got a black screen with the little bar at the top left flashing in the bottom right and "B2" then a black screen with the same small bar but not flashing. On my motherboard I have a set of code that runs and stops at B2. No BIOS.J 'tried everything:
- Move the graphics card
- Exchange up memories, play with the colors of slots, try with only 2 bar, try with 3 instead of 4 memories
- Disconnect the SSD and the HDD, change the connections at the plug SATA, try with HDD only
- Clear CMOS
- Start without devices connected (only with keyboard, mouse and screen)
- Check all my connections and CPU + Noctua
NOTHING .......................... I do not understand

Reading A0, it is at the point of OS loading. A0 is not an error.
Quote from: rastababy972 on 28-October-12, 07:07:05
I tried and I get an error A0 or A2 but nothing on the screen (my screen turns off after a while because no signal)
Even when using the onboard graphics?

New MSi Z77A - GD65 DIMM problem

I was wondering if anybody else has a similar experience with this.
My build:
i7 - 3770k 3.4 ghz
MSi z77A - GD65
MSi 760 Geforce GTX 4GB VRAM
Rosewill Xtreme RX750 - D - B
3 x 4 GB Corsair Vengeance DDR3 RAM
So everything wrongs except for the DIMM. The two DIMMs closest to the CPU causes the system to not POST. The debug stays at 55 which indicates that there's no memory. When I installed two sticks into the slots furthest away from the CPU, it boots up just fine.
I tried booting up with one stick in the DIMM furthest away from the CPU for each ram stick. They all result in the system booting up just fine. I tried using 4 x 2 gb RIPJAW ram sticks and again the system errors at 55. The common denominator here is that the two DIMM slots closest to the CPU are not working and causing everything to freak out.
This is my theory on what's going on. I have no idea how to fix this other than returning the board for a new one. Hopefully I can get some suggestions or advice on what to do from here. Maybe my mobo isn't broken, and it's just me doing something wrong. I certainly hope so because I'm a pretty lazy dude. Bought this board because my other mobo didn't boot up. Now this board isn't reading my memory. What gives??? Any help is appreciated.

Enter bios and check if the intel ME firmware is properly installed. If not it will show N/A in the bios.
My PC with the regular Z77A-GD65 worked flawless for a year, then I had problems. My gcard died and I had massive bootproblems. I tried a lot to figure out the reasons. All I could come up with was a faulty board or incompatible memory, like you think you have. I switched from 4x4Gb to 2x8 Gb in slots 2 + 4, but it didn't help.
After I noticed Intel ME firmware wasn't installed, I tried that. I used the forum tool and most important: I used a bios version with Intel ME firmware included. Downloaded it from an attachment in these forums (so don't download bios versions from the official MSI website!). I flashed the bios and everything worked great again!
Try that first, before you start inspecting CPU pins or change to different memory. I installed BIOS version 10.8B3 (beta), but watch out, I think your gaming edition of the Z77A-GD65 has a different bios. Check the forums which (beta) version is the most reliable.

MSI Z77A-GD65 Intel 7 Series Motherboard Integrated Graphics

Hi i'm a newbie to computer parts and the computer world in general on what does what. I'm only 15 but i'm looking to upgrade my Mobo and CPU I have found a bundle (MSI Z77A-GD65 Intel 7 Series Z77 Motherboard and Intel Core i5-3570K 3.40 GHz Quad Core Unlocked Bundle) on tiger direct and it looks like a good deal. But before I buy it I WAS going to upgrade my GPU before I were to get a new Mobo and CPU. I've done some research on the MSI Z77A-GD65 and I saw it has integrated graphics, but I don't entirely know what that is. I was curious if that's a graphics card and if so what it compares to. I have a Nvidia GTX 9800 graphics card that's fairly old now and I was wondering if a Mobo with integrated graphics acted as a graphics card and if so what it would compare to. If you want to know anymore specs about my computer let me know and i'll be happy to give them out.

It's not the mainboard to have integrated graphics, it's the cpu. The Core i5-3570K has Intel HD Graphics 4000 integrated. The mainboard only offers the output connectors to use it. All current generation Intel cpus have integrated graphics which can be used or not. The HD Graphics 4000 is not meant for gaming of course and would perform worse than your GTX9800 in a 3d game. With a supported mainboard (like the Z77A-GD65) the integrated graphics can be used along the discrete vga for Lucid MVP to better performance and gaming experience (see for more details: https://forum-en.msi.com/index.php?topic=160519.0).

2 x R7870 Hawk with MSI Z77A-GD65 MB in CrossFire Crashes

Hi,
I can't get Corssfire to work, as soon as an app tries to use 3D the system hard crashes, blue screens or reboots.
When I load GPU-Z the system freezes.
My system config is:
Windows 7 64 Bit
Intel Core i7-3770K
8 GB RAM
180GB INTEL SSD
MSI Z77A-GD65 MB with Bios version 10.5
2 x MSI R7870 Hawk in CF
1000 watt OCZ power supply
- Each card on its own works fine.
- I have lowered the clock speed to spec (1000Mhz)
- Using ATI Catalyst 12.8
- Cards are installed on PCI_E2 & PCI_E5 slots
- No monitors are connected to second GPU
This is a fresh system, no other drivers have been installed.
Anybody else have this problem?
Motherboard and 2 Graphics cards are all MSI.
What is the best way to uninstall ATI Catalyst so I can try older drivers?
Are the drivers ATI drivers on MSI website different to the ones on AMD's website?

Use >>Driver Fusion<< in Safe Mode to remove current VGA drivers.
Then install the latest drivers from MSI: http://www.msi.com/product/vga/R7870-Hawk.html#/?div=Driver&os=All
Try again
MSI drivers are verified for the MSI product they are offered for.

MSI GTX 970 not working on MSI z77a-gd65

The screen only shows a underline in the superior left, lights on, fans on, old vga "MSI GTX 560ti" works normally.
PC specs.
MSI z77a-GD65(MS-7751)
Intel i53570k
PSU Seasonic 520w model ss520gb active pfc f3 80plus

Quote from: Svet on 19-March-15, 04:53:06
have you done a >>Clear CMOS Guide<< with power cord removed?
what is the mainboard bios version used?
this mean top left or?
any boot codes?
I updated the bios, its working now, thanks for the reply.

MSi Z77A-GD65 powers on for 1 second then off for 5, repeats cycle.

Board: msi z77a-gd65 (ms-7751 Version 2.1)
VGA: on-board DVI
PSU: Antec BP550plus

Yeah, this forum kept squabbling about external links when I did not make any in the text so I gave up trying to post it. I canceled but I guess it made the thread anyway. I was able to fix the problem. It turns out that this mainboard is VERY picky over which brands of memory you use.

My 2nd MSI Z77A-GD65 won't start

Similar Messages

Maybe you are looking for