My 30" display only offers 1280x800 resolution

In my display system preferences, this is as high as it goes. My previous monitors all allowed between 1280x1024 and i had another crt that offered up to 1600. Shouldn't it be 2560x1600?
Thanks

The 30" display needs a graphics board with dual-link DVI to run at full resolution. If you have a G4 with mirrored drive doors, you can use the
ATI Radeon® 9600 Pro PC & MAC Edition RoHS 256MB AGP
<http://shop.ati.com/product.asp?sku=3170809>
It has two DVI ports. One port is dual-link DVI.

Similar Messages

Apple 30" only allowing 1280x800 resolution

I just bought a new 30" Cinema Display and a ATI Radeon 9600 PRO to run the new monitor in my G5 (card recommended by Apple). I installed all the software and for some reason am only getting one option in my display settings for 1280 x 800 resolution. Is this somehow related to the card requiring a connection to my computer's power supply (mentioned in the ATI book)? I tried following the instuctions for that step of the installation but I don't have the 'Y' Power Connector it refers to in the book (guessing thats something else you have to buy).
Any help/recommendations would be greatly appreciated.
Thanks.

You may have purchased the wrong Radeon card for the 30" display. The Radeon 9600 PRO PC & Mac Edition is necessary for the full 2560 X 1600 resolutions.
If you did purchase the PC & Mac card then check to make sure you are connected to the dual link DVI port.
Also you do not need seperate power connector for card.
Hope this helps

Why does my 27" LED Cinema Display only display maximum resolution of 1920x1200, when my Mid 2009 13" MBP says it supports up to 2560x1600?

When I have my MBP connected to my 27" LED Cinema Display, my display settings only show a maximum resolution of 1920x1200, when the specs on both my MBP and Display say they they support up to 2560x1600? Am I missing something?

I finally decided to just take my MBP down to the Apple store and see what would happen if I connected it to one of their new ACDs. At 1st, the guy at the Genius Bar told me that my MBP only supported 1280x800 as a maximum resolution. I told him that was for my MBP screen, and not an external monitor. Finally I convinced him to let me connect my MBP to one of their monitors. Low and behold, looking at the Display settings pane I saw some addtional resolutions, including 2560x1600!
So, now I have confirmed that my MBP can drive an external monitor to a resolution of 2560x1600, using just the single mini displayport connection. I just have to figure out what's wrong with my ACD. Suspecting that my older ACD might not support this higher resolution, I did finally discover that my model only supports a maximum resolution of 1920x1600.
Sorry for all the confusion...

Resolution of X240 and T440p with external 4:3 displays only 1280x1024, although native 1600x1200

We connect the new X240 and T440p - docked in Ultra dock - with two external 20" 4:3 displays via display-port and dvi or just both display-ports.
The maximum resolution which can be chosen in Windows is only 1280x1024 although the displays have a native resolution of 1600x1200.
We already applied all driver- and bios-update and tried different connections.
The same displays worked great with older ThinkPad models.
With 24" displays and 16:10 resolution it is possible to choose the native resolution of 1920x1200.
Solved!
Go to Solution.

The problem with the monitors which go blank can be solved:
1. Upgrade the firmware of the Ultra Dock:
Firmware:
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/options/fwdphb01.exe
Installation instructions:
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/options/fwdphb01.txt
2. Check the FRU-Number of the power supply, if it's 45N0362 than it's on of the good ones, if it's 45N0366 it's one the bad ones. In this case you should contact lenovo support to replace the bad ones.

I want to create a HD disc with my Adobe Premier Elements but I am getting low resolution. When I go to share the DVD to disc the form only offers 8pixels at the bottom. How do I burn this DVD in HD with higher number of pixels?

I want to create a HD disc with my Adobe Premier Elements but I am getting low resolution. When I go to share the DVD to disc the form only offers 8pixels at the bottom. How do I burn this DVD in HD with higher number of pixels? I have read other forums on burning HD DVD's but I do not see the option to turn the 8 pi into 40 pi the one forum recommended. I want my DVD to be HD so I may sell these videos online for my business. I can't sell them the low quality they are burning now. Hopefully you can help me. Thanks.

desalvom
Thank you for your reply.
You cannot burn your high resolution video that you can view on your computer to an AVCHD on DVD disc
that will replay through a regular DVD player. But players are marketed under a variety of names with
different support opportunities. One manufacturer may call its product MultiMedia Player, media player, Blu-ray player,
etc.The bottom line is the specifications for each of the players that are candidates for the playback of
the AVCHD format on DVD disc or the format of interest.
If you upload your HD (1920 x 1080) video to YouTube, YouTube converts the video to flash format, but it goes up as the HD video.
But, beware. Look at the YouTube viewing setting when your uploaded video is playing back. The YouTube default is not
HD. It might be 360p, 480p. If you have a 1080p video, then before the YouTube playback, you should be looking
at the video with the YouTube 1080p HD setting for best viewing. That is a YouTube matter.
Best results depend on you
a. setting up the Premiere Elements project preset to match the properties of the source media. That means, if
you have 1080p source, you (manually) or the project (automatically) set the project preset at
NTSC
DSLR
1080p
DSLR [email protected]
or the PAL counterpart, depending on your region need.
b. if you upload your video to YouTube using the Premiere Elements feature, there is a HD preset, but you cannot
customize it.....if you need customization, then you can export your Timeline to a file...in this example
Publish+Share
Computer
AVCHD
with Presets = MP4 H.264 1920 x 1080p30 or PAL counterpart
and then customize the preset under the Advanced Button/Video Tab of that preset. In increase quality, you might look to increase
the Bitrate under Advanced Button/Video Tab settings - without compromising the file size.
Then you would upload that file to YouTube at the YouTube web site.
All of the above are factors that need looking into in order to determine the why for what you wrote
I have published a shortened advertisement video to YouTube- say 5 minutes-
and it is low quality
Often SD video upscaled to HD can present poorly. But, you are dealing with a HD workflow so that should not be introduced into the matter. The setup of the project and
the properties of the source video are important, but let us start with the above and rule in or out those considerations first.
Thank you. As always, any clarification needed, please do not hesitate to ask.
ATR

Connected a new 27" LED display and only get 1280 resolution

Ok....got the monitor connected through the adapter (AD-TP400) and only get 1280 resolution....how do I get the full res on this monitor?

Interesting. I have your monitor directly connected to a 2010 Mac Pro which has the mini displayport built into the video card. I also still have the original Mac Pro (1,1) it replaced and that has the NVIDIA GeoForce 7300GT with 2 DVI ports, the one on the right being dual-link.
Where did you get the AD-TP400 adapter? I've searched on that part number and can't find it anywhere. I do see that Apple lists a connector which can do that but there is no part number associated with it.

Best for display only one option

Upgraded older mac mini to Mavericks. Previously running Lion with display at 1280x800. Now only get one setting 1024. I tried the free "Display Menu"app but same thing. Any reason for this not having more options?
Thanks, Jim
NVIDIA GeForce 9400:
Chipset Model:          NVIDIA GeForce 9400
Type:          GPU
Bus:          PCI
VRAM (Total):          256 MB
Vendor:          NVIDIA (0x10de)
Device ID:          0x0861
Revision ID:          0x00b1
ROM Revision:          3362
Displays:
S/M 150MP:
Resolution:          1024 x 768 @ 85 Hz
Pixel Depth:          32-Bit Color (ARGB8888)
Display Serial Number:          H4NT105937
Main Display:          Yes
Mirror:          Off
Online:          Yes
Rotation:          Supported

Re: SQL Help

Cloning display while keeping native resolutions.

Hi!
I want to clone my screen but I want the picture to be displayed in de the native resolutions of both my displays.
Situation:
I have a 17" MacBook Pro (native resolution =1680x1050) and I have a 19" LCD-panel (native resolution = 1280x1024). Now, if I connect the LCD-panel with my MB P my desktop is being cloned. The resoltion on both monitors changes to 1280x1024.
So, no problem fot the 19" LCD-panel (Because the picture is being displayed in the native resolution of the screen.) but the picture on my MB P looks very "yuk".
Is there a way to correctly display the the picture (my desktop) on both monitors?

You can't "clone your display" at both native resolutions (for one thing, the aspect ratio is very different between your two displays). Running an LCD display at anything other than it's native resolution leads to a "fuzzy" appearance due to the way LCDs generate an image - there's no fix for that, it's a physical property of the technology.
You have mirroring turned on. With the external display connected, go to System Preferences > Displays > Arrangement tab and UNcheck the Mirror Displays box.
Now you will have a desktop that spans across both displays, and you can use both at once.
(Note - when you first uncheck mirroring, the external display may have the generic Apple desktop background. If so, go to System Preferences > Desktop & Screen Saver and it will refresh and shop your chosen backdrop on the external monitor as well. Also note that your menu bar and dock will only show on your internal display.)

Retina display wakes in high resolution / breaks Displays panel

Hi all,
Yesterday I used my new retina MBP with an Apple TV, mirroring its screen up on the AppleTV for a presentation. Since then, whenever I wake the MBP (I have its Energy Saver settings set to sleep the display but not the computer after a time), it wakes in super high res with tiny tiny tiny text (this may be 2880 x 1800 but I can't tell, but it's higher res than the highest setting the Display panel offers you).
Then, because I want to reset it to something readable, I open the Displays panel, and click Best for Retina or such, and it doesn't change. None of the resolution settings do anything. The Display panel is not entirely broken, because the GUI functions, as in, highlighting different options I choose, but there's no reaction.
To fix it, I've found I can go into the menu bar icon (rectangle with triangle under it, the AirPlay icon), set the MBP to Airplay mirror to itself (which strikes me as an odd option to have available). This changes the screen to something pretty low res with letterboxing at top and bottom, and asks me for a Airplay password for my own system. I say Cancel, and then my Displays panel works again, and I can select Best for Retina.
Any tips? Seems like a bug.
sg

Maybe http://helpx.adobe.com/acrobat/kb/hi-dpi-retina-display-support.html ?

My external 27" AOC display only runs with 1080p

My external 27" AOC display only runs with 1080p, even though my 27" iMac is capable of 2560x1440 via the attached mini-DisplayPort to DisplayPort cable. How can I get 2560x1440?
When I run recovery mode, then I get the full 2560x1440 pixels. But when I boot back to 10.9.2, then I can only choose a maximum of 1080p.

After some hours I found a solution...
But let me vent a little bit first: My MacBook Air, which I have not yet upgraded to Mavericks, is able to drive the AOC display through DisplayPort at full resolution without a problem.
Even an older lenovo Notebook with Windows 7 immediatelly used the intended resolution when hooking up the 27" screen. Windows 7 outplaying Mavericks. Oh boy...
So it seems, that Mavericks introduced some "improvement" that limitd "unknown" displays to 1080p...
By the way: Clearing PRAM didn't resolve my issue. Neither did holding down the Option key when klicking in the "Scaled" button in the screen resolution area of the system preferences for my screen.
Anyway: I found out that I can use the plist file for a DELL 27" screen, which google found for me, copy this to /System/Library/Displays/Overrides and then rename the folder and file to match the ID I got back from ioreg.
Obviously one has to be careful when mixing hardware data in this way. But since a modern screen will simply refuse to be driven with a signal that is out of spec, and since there are not too many different 27" pannels with 2560x1440 out there these days, this felt like a pretty safe thing to do... Your mileage may vary though!
Unfortunately I don't have a plist editor installed. Thus I can only look at the XML contained in the plist file. With the plist editor from Mac (-> dev tools) it should be possible to edit available resolutions directly (in hex).

Battery , time , signal strength bar is not getting displayed in home screen , these will be displayed only when i click on any app. Can u let me know the setting change ?

Battery , time , signal strength bar is not getting displayed in home screen , these will be displayed only when i click on any app. Can u let me know the setting change ?

Did you check the Zoom setting?
Have you tried a reset (reboot)? Hold HOME and SLEEP until an Apple logo appears.
If it isn't Zoom and a reboot doesn't help try Settings/General/Reset - Reset all settings

EXACTLY what cable(s) do I need to connect my MacBook Pro (early 2011) to an external display with a 2560x1440 resolution?

I am trying to connect my MacBook Pro (early 2011 w/ Intel HD 3000/ 384Mb) to an external display with a 2560x1440 resolution. Specifically, what cable/connections do I need to display at this resolution? I cannot get the display to work using a "Thunderbolt to HDMI" or a "Thunderbolt to DVI" connector. Note: I used both older and newer (uni-directional) HDMI cables on the first config, and a Dual-link DVI cable on the second config. Apple specs state this is possible ( support.apple.com/kb/SP619 ), but I am at a loss as to how this can be done. Thanks in advance for the help!

You use a Mini DisplayPort to either HDMI or dual-link DVI adapter. If that component doesn't work, something's wrong with either the cable or something else in the connection.
(112855)

Is it possible to display only dynamically selected fields in the out put?

Is it possible to display only dynamically selected fields in the out put? i need to display set of columns in the selection criteria, but in the output i have display only input given fields. because i need to convert it into .csv file. So i have to display selected fields from internal table. In oracle they are using"execute immediate". is there any equivalent in SAP?
thanks in advance.

Hi Remya,
Are you talking about dynamic programming in ABAP ?
If yes, there are concepts like RTTS which facilitates it.
Yes, the select query also supports dynamic selection of fields. ( Please care about ( ) in dynamic sql ).
Do more research on Field Symbols and statements like ASSIGN COMPONENT OF.
Regards,
Philip.

Crystal report displays only few pages,

Hello,
We have problem with crystal report preview option. Basically its a cross tab report and when we have a preview it displays only two pages. Even though we have 40 pages worth data.
When we export to PDF we see all pages of data. If we print directly from crystal only 2 pages gets printed.
Thanks
Sridhar.

May i know the pages spreads over horizontal or vertical?
Regards
venkat

Display only/Grey out Delivery Schedule tab in the PO

We are not going to use Delivery Schedule tab at all. Business wants us to Grey out the delivery schedule tab. Is it possible to make all fields under Delivery Schedule as display only? If yes, how can I do that? But, I don't want PO line qty to be grayed out.
Fields like, delivery date, scheld qty, stat.del date etc.
Thanks everyone.

you better convince your business to wait for a couple months and then rethink this requirement.
You may not have the full understanding yet and have not made a lot experience.
in this tab you can add further requisitions to your PO item, you can close requisitions in case you order less than a requisition, you have to change the statistical delivery date in some case when you are using vendor evaluation, you may have to split the order quantity into several delivery dates if your vendor informs you that he cannot supply you at one time with all quantity.
Just to save you money that you may spend into a development which has to be turned off a little later.

My 30" display only offers 1280x800 resolution

Similar Messages

Maybe you are looking for