My 5220 printer gives me a C000 error messge.

My Canon is an MG5220 Out of nowhere this message screen came up. It tells me to turn off computer, then turn on again. I did....same message. It says to "see the manual." Love that.
I unplugged the cables to the printer while it was off. Then turned on. No change
Plz help
Kris Serven

Hi Kris Serven,
The C000 error is a generic internal error code, it could mean one of many things. To try to resolve the C000 error, please follow the following steps:
1. Turn off the printer and disconnect the power cord and USB cable.
2. Remove paper from the automatic sheet feeder (in the back).
3. Gently pull jammed paper out, if any.
3-1. If paper is visible from the ASF, use both hands to pull the paper out slowly.
3-2. If paper is visible from the paper output slot, use both hands to pull the paper out slowly.
4. If the paper tears and a piece of that remains inside the printer, open the printer cover and remove the paper from inside the printer.
5. Check ASF with a bright light to check for obstructions. Remove any if found.
6. Open the rear cover to check if the paper is jammed.
7. Pull out the cassette and check if the paper is jammed inside the cassette area.
8. Load paper back into the ASF or cassette.
9. Reconnect the power cord, turn on the printer and confirm that the Alarm light is off. (If there was any jammed paper remaining in the printer, the paper may be automatically ejected.)
If the above procedure does not resolve the C000 error, please contact our support group using the following link:
http://www.usa.canon.com/cusa/consumer/standard_display/contact_us_consumer
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

Repeated C000 error MG5350

Recently my printer started giving a C000 error message. When I got this error, I restarted the printer, but the error persisted.
After some googleing, I took the ink cartridges out of the printer and reinserted them (whilst also checking if there was no stuck plastic on the cartridges, or other strange stuff on the inside of my printer). I then noticed some leaked ink on the inside of my printer (on the right side), but I do not know if this is relevant to this problem. Because I removed the power cable out of the printer, it seemed like this solution worked, because it did start printing a few pages (just one printerjob to be exactly), when the second job started, it again gave the c000 error after printing one page.
Powering down the printer and removing the power cable again still gives the same result. Since the printer can print, it seems unlikely that there is a problem with the ink cartridges or with any stuck paper, however, I might be wrong.
Can somebody shed some light on my problem? Thanks in advance!

Adobe posted a troubleshooting document in Illustrator area:
http://kb2.adobe.com/cps/824/cpsid_82414.html
I read it thoroughly since I am still experiencing the popup error messages when using either selection tool on objects. I did a uninstall and install of CS5.1 (CS5.1 for the suite 5.5 upgrade) and did not install the VectorScribe and XtreamPath 1.4 plugins. The "unplugged" Illustrator worked fine. I then installed VectorScribe -- no problems. Then XtreamPath 1.4 - voila the error popped up.
Anyone else use XtreamPath 1.4 with Lion and had problems? I sent CSValley Support to ask if their plugin works under Lion (according to their system specs, it should).
UPDATE 8-5-11: (CSValley promptly replied back that they had not received any issues similar to mine.)
I installed both plugins (VectorScribe and XP 1.4) on my Macbook Pro and had no problems there which led me to think the XP plugin might be corrupted on my main work machine (MacPro). So I copied the plugin from the MBP to the MacPro and happily (knock on wood) am not getting the error messages.
Somewhere along the way of installing the CS5.5 upgrade and MacOSLion, my XtreamPath plugin was affected.

Since upgrading to ios 8.0.2, airprint will give error (no printer found" After a reboot, it locates and prints, then next time same error code. Any ideas?

Since upgrading to ios 8.0.2, airprint will give error (no printer found" After a reboot, it locates and prints, then next time same error code. Any ideas?

Hi bdtcop,
I understand that you are experiencing an issue with AirPrint. Here is an article for you with some troubleshooting steps that may be helpful for resolving this issue:
About AirPrint
http://support.apple.com/kb/ht4356
If you're unable to print
Check these things if you are unable to print, or if you see the message "No AirPrint Printers Found."
Make sure your printer has paper, and enough ink or toner installed.
Make sure your printer is connected to the same Wi-Fi network as your iOS device.
Make sure your printer has power and is turned on. Try turning your printer off and then back on again to see if it resolves your issue.
Check to see if your printer has any error lights or indicators displayed on the printer's control panel. Check the documentation that came with your printer to clear any errors displayed.
Check with your printer's manufacturer to see if any firmware updates are available for your printer. Check your printer's documentation or contact the printer vendor for more information. A firmware update may be available, even if you just bought your printer.
Thanks for using the Apple Support Communities. Have a good one!
-Braden

After installing OS X Mavericks on myMacBook Pro the Canon IRA 6055 printer gives me "Open error. Switch the printer off and on, and then start the print job again.: 16013" Any sugestions?

After installing OS X Mavericks on myMacBook Pro the Canon IRA 6055 printer gives me
"Open error. Switch the printer off and on, and then start the print job again.: 16013"
Any sugestions?

This is the new problem
I pinged the ip address and i looks to be working
So I'm not sure how to procead
I nstaled the lates driver package also

Error print success message checksum content error: Action procesada.

I have a problem with an application in the HTML DB that I am creating. the problem is:
I create plicacion from each one of the tables, when trying to enter a registry in the application of concept, sends east error to me, but if it stores the registry. the error is:
Error print success message checksum content error: Action procesada./6Ã1Ã9ÃFE08952600ACEC1E0188ÃC/: 4730F16841157B21D061A969F6640A61.
the design I did it with Oracle designer.
the model contains three tables:
1. file .tab the designer
PROMPT Creating Table 'CONSULTOR'
CREATE TABLE CONSULTOR
(ID_CEDULA NUMERIC(12) NOT NULL
PROMPT Creating Table 'CONCEPTO'
CREATE TABLE CONCEPTO
(ID_CONCEPTO NUMERIC(3) NOT NULL
,DESC_CONCEPTO VARCHAR2(120)
,FACTURABLE VARCHAR(5)
PROMPT Creating Table 'GENERAL'
CREATE TABLE GENERAL
(ID_GENERAL NUMERIC(5) NOT NULL
,CONC_ID_CONCEPTO NUMERIC(3) NOT NULL
,CONS_ID_CEDULA NUMERIC(12) NOT NULL
,FECHA_ACT DATE
,DESCRIPCION_ACT VARCHAR2(120)
,CANTIDAD_HORAS NUMERIC(5)
2. file .con the designer
PROMPT Creating Primary Key on 'CONSULTOR'
ALTER TABLE CONSULTOR ADD (CONSTRAINT
CONS_PK PRIMARY KEY
(ID_CEDULA))
PROMPT Creating Primary Key on 'GENERAL'
ALTER TABLE GENERAL ADD (CONSTRAINT
GENE_PK PRIMARY KEY
(ID_GENERAL))
PROMPT Creating Primary Key on 'CONCEPTO'
ALTER TABLE CONCEPTO ADD (CONSTRAINT
CONC_PK PRIMARY KEY
(ID_CONCEPTO))
PROMPT Creating Foreign Key on 'GENERAL'
ALTER TABLE GENERAL ADD (CONSTRAINT
GENE_CONC_FK FOREIGN KEY
(CONC_ID_CONCEPTO) REFERENCES CONCEPTO
(ID_CONCEPTO))
PROMPT Creating Foreign Key on 'GENERAL'
ALTER TABLE GENERAL ADD (CONSTRAINT
GENE_CONS_FK FOREIGN KEY
(CONS_ID_CEDULA) REFERENCES CONSULTOR
(ID_CEDULA))
3 file . lis de designer
Reconcile Report: C:\Documents and Settings\rolando\Mis documentos\aso\xxx.lis
Generated on Tue Jun 07 09:55:25 2005 by Server Generator 9.0.4.3.14
====== ======== ================ ==============
Object Property Repository Value Database Value
====== ======== ================ ==============
Object Property Repository Value Database Value
Table CONCEPTO * NOT IN DATABASE * ***
Object Type
Data Persistence Permanent
Cluster
Index Only No
Cached
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Comment
Column ID_CONCEPTO * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 3
Scale
Mandatory Yes
Default Value
Domain
Comment
Column DESC_CONCEPTO * NOT IN DATABASE * ***
Datatype VARCHAR2
Max Length 120
Scale
Mandatory No
Default Value
Domain
Comment
Column FACTURABLE * NOT IN DATABASE * ***
Datatype VARCHAR
Max Length 5
Scale
Mandatory No
Default Value
Domain
Comment
Primary Key CONC_PK * NOT IN DATABASE * ***
Enabled Yes
Deferred No
Immediate No
Exception Table
Key Column ID_CONCEPTO
Index CONC_PK * NOT IN DATABASE * ***
Unique Yes
Global No
Bitmapped No
Compute Statistics No
Reverse No
Nosort No
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Snapshot Log No No
Table CONCEPTO Differences: 1
Object Property Repository Value Database Value
Table CONSULTOR * NOT IN DATABASE * ***
Object Type
Data Persistence Permanent
Cluster
Index Only No
Cached
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Comment
Column ID_CEDULA * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 12
Scale
Mandatory Yes
Default Value
Domain
Comment
Primary Key CONS_PK * NOT IN DATABASE * ***
Enabled Yes
Deferred No
Immediate No
Exception Table
Key Column ID_CEDULA
Index CONS_PK * NOT IN DATABASE * ***
Unique Yes
Global No
Bitmapped No
Compute Statistics No
Reverse No
Nosort No
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Snapshot Log No No
Table CONSULTOR Differences: 1
Object Property Repository Value Database Value
Table GENERAL * NOT IN DATABASE * ***
Object Type
Data Persistence Permanent
Cluster
Index Only No
Cached
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Comment
Column ID_GENERAL * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 5
Scale
Mandatory Yes
Default Value
Domain
Comment
Column CONC_ID_CONCEPTO * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 3
Scale
Mandatory Yes
Default Value
Domain
Comment
Column CONS_ID_CEDULA * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 12
Scale
Mandatory Yes
Default Value
Domain
Comment
Column FECHA_ACT * NOT IN DATABASE * ***
Datatype DATE
Max Length
Scale
Mandatory No
Default Value
Domain
Comment
Column DESCRIPCION_ACT * NOT IN DATABASE * ***
Datatype VARCHAR2
Max Length 120
Scale
Mandatory No
Default Value
Domain
Comment
Column CANTIDAD_HORAS * NOT IN DATABASE * ***
Datatype NUMERIC
Max Length 5
Scale
Mandatory No
Default Value
Domain
Comment
Primary Key GENE_PK * NOT IN DATABASE * ***
Enabled Yes
Deferred No
Immediate No
Exception Table
Key Column ID_GENERAL
Index GENE_PK * NOT IN DATABASE * ***
Unique Yes
Global No
Bitmapped No
Compute Statistics No
Reverse No
Nosort No
Initial Transactions
Max Transactions
Percent Free
Percent Used
Initial Extents
Next Extent
Min Extents
Max Extents
Percent Increase
Freelists
Freelist Groups
Tablespace
Parallel No
Foreign Key GENE_CONC_FK * NOT IN DATABASE * ***
Enabled Yes
Deferred No
Immediate No
Cascade Delete RESTRICT
Cascade Update RESTRICT
Exception Table
Join Table CONCEPTO
Key Column CONC_ID_CONCEPTO
Referenced Column CONCEPTO.ID_CONCEPTO
Foreign Key GENE_CONS_FK * NOT IN DATABASE * ***
Enabled Yes
Deferred No
Immediate No
Cascade Delete RESTRICT
Cascade Update RESTRICT
Exception Table
Join Table CONSULTOR
Key Column CONS_ID_CEDULA
Referenced Column CONSULTOR.ID_CEDULA
Snapshot Log No No
Table GENERAL Differences: 1
====================================================================================================================================
Total Differences: 3
====================================================================================================================================

Rolando - We don't need all that information about the data model and such. Can you describe what the application does on the page that gives the error? I mean, you submit the page, it performs some after-submit processes (what do they do and how many processes are there?) and then it has some kind of branch to the same page or another page. Describe the processes, show us the success message for each process, exactly as they are formatted in the process definition page, and describe the branches (to the same page, another page, do they use URL redirects? And also please post the entire URL that you see when the error page is displayed.
Finally, please provide all the output from the About HTML DB page: Workspace Home -> Click the About HTML DB link under Workspace Administration on the far right side of the page. Then copy all the output and show it here.
Scott

I have a C000 error message when trying to turn on my Pixma MG8120.

I replaced some ink cartridges and immediately received a C000 error and cannot turn the machine on now. There are no paper jams. I tried putting the old cartridges back in - but that didn't help. The printer has been working fine til now. Help?

Same problem here...nothing in my settings have changed since the upgrade and I've checked my cookie settings and they allow 3rd party cookies. What's up Mozilla? I've been faithful to you for years and you let me down now?

My iMac 8.1 was slowing down and had permissions problems. I backed everything up, and then re-installed. Now all I get is a black screen. Power+D gives me a hardware error message: HDD-1336. Help!

My iMac 8.1 (10.6.8 ) was slowing down and had recurrent permissions problems, mostly with Java. I backed everything up, and then re-installed from time machine. Now all I get is a black screen which says I need to reboot. Power+D gives me a hardware error message: 4 MOT/1/40000003: HDD-1336 or HDD-1327. When I reboot from the OSX CD and start disc utilities everything checks out OK. When I reload 10.5.2 from the OSX CD everything seems to work OK and no more permissions problems. But then I loose all my email and safari stuff. Anyone have any ideas short of going back to my old PC?

DonM. wrote:
Hi
Thanks for the help. No point in fooling around with it any more. Will I be able to use it as a monitor if I get a mimi mac?
Cheers. Don
No unfortunatley it's too old, you are referring to Target Display Mode which became avialble in 2009, your 2008 needs to have the HD replaced. I'd still do that if everything else is OK or you can simply buy a new MM and display or even a new iMac or an Apple refurbished iMac to save money.

Printing dunning notices using SMARTFORMS,error during parameter transfer

Hi Friends,
                I face a error message "Include text ZGA_DUN_HDR does not exist (object TEXT, ID ST)" when i run the dunning run.
                I had searched every node for text ZGA_DUN_HDR in the smartform,I didnt find the text in it.
However when I execute the smart form for print preview an error message "Printing dunning notices using SMARTFORMS,error during parameter transfer".This error i believe is due to wrong parameter passing in the fm 'GET_SF_DUNN_DATA'.It raises an error no_parameters_found.All parameters are passed correctly.
                Can you guys help me out.
Edited by: RAJIV KAUSHAL on Nov 14, 2008 6:03 PM

you can create this text ZGA_DUN_HDR in SO10 tcode and try ...

When trying to work with Agilent 34401A multimeter (serial RS-232 connection), HP34401A Getting Started.vi gives always the message: "Error 1073807369 occurred at Old VISA Open ".

Baud rate and parity are set correctly, RS-232 cable is also connected correctly. My QuickBasic program has no problems to read and write to the Multimeter. It is obviously a software problem: the same error is persistent if I disconnect RS-232 cable.
I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm digital.ni.com and installed it. But it did not help.
Thank you in advance
Best regards
Alexei Soloviev

Hi Steve
I have problems with the 34401A and serial communication. Do you remember
where the error was in the code ?
Thanks
Klaus
wrote in message
news:[email protected]..
> Alexei,
> This may or may not help, I was tasked to do something similar
> recently and found an error in their driver. The GPIB VISA worked
> fine, but when I tried it on serial it played up. There was an errant
> carriage return (or CR/LF I can't remember). GPIB liked one and Serial
> liked the other. It always amuses me that we never have problems with
> Quickbasic!.
> If you want me to dig deeper give me a shout.
>
> Steve Watts
>
> On Thu, 24 Jan 2002 06:16:55 -0800 (PST), "Alexei V. Soloviev"
> wrote:
>
> >When trying
to work with Agilent 34401A multimeter (serial RS-232
> >connection), HP34401A Getting Started.vi gives always the message:
> >"Error 1073807369 occurred at Old VISA Open ".
> >
> >Baud rate and parity are set correctly, RS-232 cable is also connected
> >correctly. My QuickBasic program has no problems to read and write to
> >the Multimeter. It is obviously a software problem: the same error is
> >persistent if I disconnect RS-232 cable.
> > I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm
> > digital.ni.com and installed it. But it did not help.
> >Thank you in advance
> >Best regards
> >Alexei Soloviev
>

Since installing the latest update, Firefox will not load; it gives me the following error -- XML Parsing Error: not well formed.

since installing the latest update, Firefox first operated with some errors but now will not load at all; it gives me the following error --
XML Parsing Error: not well formed
locations chrome://browser/content/browser.xml
Line Number 1191, column 20:
utton id="back-forward-dropmarker" type="menu" chromedir="&locale.dir;"-------------------
please note that the words "utton ID" are exactly as the error message gives it; and at the end of the message there are exactly 19 hyphens.
I don't know why this faulty code is referencing things to do with "chrome"... the Chrome browser is not installed on this PC or anywhere on our network.
Also, this is not the first problem I had after clicking Firefox's prompt for the latest update. Before Firefox retreated into this error message, it was loading but running with some faults...
1. the bookmark symbol was not appearing on the right hand side of the URL line, so I had always to click on "bookmark this page", after which the bookmark symbol did appear; however I don't know if the bookmarking function worked properly.
2. the back and forward buttons were not highlighted, as if I had not come from a previous page; so once I clicked on a link to a new page I could not go back to where I came from because Fiefox thought I hadn't come from anywhere.
3. there may have been other errors, but I did not find them.
How do I reinstate my Firefox program to work properly please? do I have to download the latest version and reinstal? if so, do I have to remove the old version first? or is there a fix?
Even to write this message I have been forced to use (yuk -- I don't like to say this!!!) Internet Explorer. So please -- I need help urgently.
Thanks,
NOEL

Some how I solved my problem by opening a user account and downloading Firefox 4.0 beta and installing it, I did try it, worked fine, so I did close the user account and did go back to my own account(switched user), the main page that I had problem with Firefox which would not open, I dabble click on Firefox it start working again!! I hope that solves your problem too.
firefox will not open, it gives me this cod and would not turn off, Error on switching in renew: NS_ERROR_UNEXPECTED, Component returned failure code: 0x8000ffff (NS_ERROR_UNEXPECTED) [nsIPrefBranch.getCharPref] id: none

I am trying to print a fillable form. It will not print and I get two error messages "document could not be printed" and "there were no pages selected to print." Th latter is not true. Won't print all, the page I am on, nor any series of pages inserted

I am trying to print a fillable form - - an application for a Chinese visa. It will not print and I get two error messages: "document could not be printed" and "there were no pages selected to print." The latter is not true. Won't print at all, the page I am on, nor any series of pages inserted.
Am using a MAC desktop and a Cannon PIXMA MX922 printer.
I need to print this form now that it is filled out? What can I do?

Hello PW, I am having this problem and all suggestions haven't worked yet. Where is the Preferences|Documents you are referring to? I am on a PC and using Windows.
EDIT: I found it and did, but still not working.

When printing I get notation:"An error has occurred in the script on this page"

when printing I get notation:"An error has occurred in the script on this page", error 1791-Char 1- error invalid argument-Code 01-Can print Word, but not Web pages. Have Windows 7, Home and Internet Explore 10. Please help

Sorry that you are having a problem with the script error.
Try to clear your CACHE and COOKIES on your internet.
Are you able to print from another program, such as Firefox, Google chrome, etc?
Let me know if it prints.
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

Print with pasta and getting error

hello, i have customs printing driver for pasta but as i print report i find an error,
APP-FND-00500: AFPPRN received a return code of failure from routine FDUPRN. Program exited with status 1
Cause: AFPPRN received a return code of failure from the OSD routine FDUPRN. Program exited with status 1.
The output .pdf has zero file size.
Any one help? .
And how can i locate which part cause this problems?
Thanks.

Please post the details of the application release, database version and OS.
Please see if these docs help.
How to investigate printing issues and work towards its resolution ? (Doc ID 297522.1)
APP-FND-00500: Afpprn when Using pdf2ps with Pasta (Doc ID 413402.1)
APP-FND-00500: AFPPRN ... An Error Occurred In Getting Printer Driver Information (Doc ID 867965.1)
How to Print PDF with UTF8 in R12? (Doc ID 778970.1)
11i : Pasta Pasta Printing Setup Test (Doc ID 264118.1)
Diagnostic Test Catalog for 12.1.3 (Doc ID 1083807.1) -- PASTA
Thanks,
Hussein

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. Bad job testing the software Apple.

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. What's the fix? None of the recommended fixes work in any of these devices. Reset device, reset network, renew lease, etc. None of them work.

Does the iPod work OK?
Does it charge when connect to the computer?
Does it appear in My Computer?
Look at the dock connector on the iPod. Compare with the iPod that does work/connect.
I suspect you have a 2G iPod. Those can only go to iOS 4.2.1
http://support.apple.com/kb/HT1353#iPod_touch_late2009
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

Can't share local printer in Windows 7 Pro-error 0x000006d9

Hello,
I recently purchased a laptop and wanted to share my local printer, attached via USB to my desktop (tower) in my home. My desktop runs Windows 7 Professional 64-bit. My laptop runs Windows 7 Home Premium 64-bit.
When I try to share my printer, accept the default printer name (or modify it), from the sharing tab of printer properties, I get an error: "printer settings could not be saved. Operation could not be completed (error 0x000006d9)".
I did some searching in this forum and via google but this error code does not appear for this type of issue (i.e. printer sharing). Does anyone have any suggestions?
I also verified my Event Viewer and see no errors whatsoever related to printer or network settings or file and printer sharing. I CAN share my files on THIS desktop with the laptop and have already transferred files from the desktop to the laptop successfully. But printer sharing is giving the above error.
** Also, I MAY have a related problem but I am unsure about this, so I wanted to mention this in this same thread in case they are related: I cannot start the homegroup listener service from services on the desktop (win 7 pro) - get error code 2147023143. Homegroups are NOT setup (not created) on neither the laptop nor the desktop. Again, I tried to search for this error code but the results are inconclusive.
Any suggestions would be appreciated.
John

Its now been THREE YEARS since this "bug" has been discovered and resolved by a user, and there is not one word about it in MS's online help. Today I had this exact issue of not being able to share a printer on Windows 7 with other computers on my
my local network. And this is the same printer I've been sharing with the same network for nearly FIVE YEARS!! I have always used 3rd party virus/firewall software, but I don't disable the windows firewall. Rather I just set it to "Manual"
because some network software seems to need it occassionally. The result is the same however, as is the solution. I had updated and reinstalled my printer software, and apparantly sharing is disabled by default. After stumbling upon this
thread, after several hours wasted searching Windows Help and Microsoft "NON"-Support websites and KB's, I simply ran the firewall just long enough to enable sharing, and instantly the backlog of spoolled print jobs began printing.
Thank you. You would think MS would have at least written this solution into their help files by now ... but than again, they are probably making money with their "paid" support option from all the desperate people who suddenly can't use there printers.
Probably charging $50 just to tell people to turn the firewall on for a few seconds. I can't think of another reason to conveniently omit this simple solution from the "free" support.

My 5220 printer gives me a C000 error messge.

Similar Messages

Maybe you are looking for