My 5c is stuck in reset load mode and has been for 2 days
help
First, try holding down both the power and home buttons until the device restarts. Tell me what happens after that please.
Similar Messages
-
Updated 5c to 8.1.3 but its stuck on the loading screen and has been for hours
I updated my iphone 5c to the 8.1.3 and its been stuck on the loading page for hours now. I've tried pressing buttons and unplugging it but it won't do anything.
"Pressing buttons" is vague, make sure you've tried a reset:
Hold both the home and power buttons at the same time until the Apple boot logo appears.
If that does not work you may need to restore the phone: see http://support.apple.com/kb/HT1808 -
My iphone 4 has been in recovery mode for almost 2 days i connected to itunes and restored my phone said it would take 6 hrs to complete today it has been one promblem after another back up the computer, update newest verizons, change software, ect...i was halfway through a download when i lost internet service fixed that now it cannot contact my server each time ive started over which was alot i had to restore my phone each time...is there something else that can b done ?
Temporarily disable any security software on the computer then try again.
-
so yeah, my phone is totally unresponsive, what do i do :/
Hi McCrubb!
I have an article here that can help you restore your iOS device more thoroughly:
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
Thanks for using the Apple Support Communities!
Cheers,
Braden -
I tried updating my ipod touch to iOS6 then an unknown error occured so i disconnected it an now it is stuck on the apple sign and has a loading sign and has been like this for 2 hours. what can i do?
My home button is also unresponsive and i have to press it really hard to make it work.Do you remember the the exact wording of the error message:
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
please help! i have just upgraded to an iphone 5 for work, so i have started to backup my iphone 4 but it is stuck on 'finishing sync' and has been for 20hours!what can i do?i need it for work tomorrow
Is this what you downloaded: iTunes 10.7?
When the update fails what if any error report do you get, specifically? Please do this before trying again:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X. -
i disconnected my iphone 4 while it was updating and now its frozen, the screen is showing a apple logo and a loading bar which has been for 9hrs now. please help
It's not uncommon for it to not work the first time and sometimes, you have to try it a few times. Turn off your antivirus software and your firewall while you are trying to restore the iPad. Enable them again after you restore.
If that still won't work, post back with detailed information as to what exactly does happen as you go through the process. -
iPad started acting up, would not open books, screens come up that I never touched etc. so I did a reset, the apple icon showed up and has been on now for about 18 hours I can't even turn it off I plugged in in over night but still screen frozen? Any suggestions?
Hello there, Gina1964.
The following Knowledge Base article offers some great information for troubleshooting the issue you're describing:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
Pro9000 Mark II stuck in front load mode
I printed using front load (13x19 sheet) on my last print job. I changed just now to using 8.5x11 (after the printer was shut off) and now it's stuck in front load mode and will not print (unless I printed from front load which makes no sense to do).
Is there a setting I need to change to get it back to normal printing? Getting it into front load is done using the buttons on the front of the printer. Nothing is lit up now except the power button. The bottom tray is down in normal printing mode. The back tray is up.
I opened Print Setting > Quality & Media > Paper Source > change to Rear Tray and hit Save. It doesn't take. I hit Print (Lightroom Print Module) and print queue still says it wants to print from the front tray. When I go back to Print Settings to check the Paper Source it again reads Rear Tray.
Thanks for your help!
TerryWhat system are you using? You may need to delete your print spooler (Win). You also need to turn off the printer for some time, overnight, perhaps. Reboot the computer. Turn the printer on.
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 9, Lightroom 6 -
I went on vacation a few days ago and in El Salvador, they have this mobile broadband sticks. Well, I was using one until it gave me a network error. After that, it shut down my computer entirely. The first time it happened, I didn't think much of it. I took the battery out and put it back in for it could work. It happened another two times, and after the third time, my MacBook stays stuck at the loading screen, and it will take 5-10 minutes on that screen, before it shuts down, or it wouldn't turn on at all. I've tried booting into safe mode, but it appears to not boot into it. I've tried resetting the Pram, and using disk utility, but that still won't work. I don't know what else to do to make it boot into OS X Lion.
I'm an AP student, and the majority of my work is in that computer, and it is very important! What can I do? Not only that, but I enter school in a few weeks and I need the AP work by the time I enter.
What can I do? Can someone help?
ThanksReinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer. -
my ipad has been stuck in a recovery mode and i cant restore it through my laptop due to less internet speed. can i submit it to apple store? will they make it alright?
Hello Elliiee,
The steps detailed below can help stabilize your iPhone.
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If the display turns on, go to step 4.
If the display remains black, go to next step.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
My issue is still not resolved. What do I do next?
Contact Apple Support.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Cheers,
Allen -
My problem is that when attempting to load updateed Pages the app has frozen in 'loading' mode and will not complete the loading. It is now unusable and does not respond to turning off the iPad and restarting. The Pages icon is in 'shadow' and will not respond . Cannot get the red minus symbol. Can get X symbol but do not want to trash it because it contains many documents I do not want to lose. Suggestions welcome!
Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. The screen will go blank and then power ON again in the normal way.] It is app and data safe!
-
my ipod screen is stuck on x-ray mode and i have no idea how it got that way and i dont know how to change it back.
A) This is the iPhone forum.
B) Even if it was the iPod forum, your post makes absolutely no sense. -
Is there any way to save the data on my ipod if it is in recovery mode and has to be reset?
Is there any way to save the data on my ipod if it is in recovery mode and has to be reset?
Only if this program will get the iPod out of recovery mode.
RecBoot: Easy Way to Put iPhone into Recovery Mode -
Hi!! I was updating my iPhone 4s to ios 6 and It got stuck on the recovery mode and I had to do a company restore!!
Unfortuntately I lost all my photos including images of my daughters birth of which I had not taken a backup
Is there any possibility of recovering the same? my wife is going to kill me!!No backup, nothing to recover.
Maybe you are looking for
-
Hi all, I'm dealing with an BaseEJBException (ejb.exceptions.BaseEJBException: Exception in method process). I send a soap message to XI and this exception is returned (message does not appear at sxmb_moni). This scenario was working fine, I think it
-
Defining ABAP variables in update rules
Hello, How can I define a variable in ABAP of the same type as an InfoObject? I know it's easy as long as the InfoObject is a part of the communication structure. But this InfoObject is not present neither in the source ODS nor in the target cube. It
-
Dear All we are loading the january,08 sales invoice from the legacy system to SAP system through BDC program. for this at the time of PGI we are using Actual GI date as month of January, 08 and keeping planned GI date as the system date and at the
-
My mid 2012 Macbook pro's built-in camera won't come on, even with native Apple apps.
This was an issue before I installed Mavericks (just today -- October 22, 2013). After resetting PRAM, CMS, restarting, the camera came back briefly yesterday, nowhere to be seen since.
-
Getting 24P raw footage from PP ro ENcore
Could someone outline an inter-application rundown between PREMIERE PRO and ENCORE of procedures and settings that make the most of 24P raw footage in editing and output. This would include navigating extremely confusing respective frame rates of 23.