My Airport does not connect to network from Windows laptop, but guest network does connect to internet

I set up my new Airport Extreme and can connect to the network with any IOS device (iPod Touch, iPhone or iPad). When attempting to connect to network with my work laptop (Windows 7), I get an error that it cannot connect. I have no problem connecting to the Guest Network on this laptop. Unfortunately, no network connection.
I have Cox Communication Internet through there Motorola SURFBoard Cable Modem Model No. SB5101U.

Hey there shriya bhardwaj!
I have an article for you that will help you troubleshoot this Wi-Fi issue on your computer:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Thanks for using the Apple Support Communities. Have a good one!
-Braden

Similar Messages

Installed Airport - getting "not connected to internet" error

I recently purchased a MacBook Pro and Airport extreme. I installed the Airport using MacBook (Snow Leopard) then hooked up my desktop iMac (OS X (10.4.11) - as per Tech Support recommendations. Everything works but here is a problem I encounter. When I wake the iMac and pull up Safari or Firefox I'm getting an error message of "not connected to internet" and the diagnostic box appears. I can hit "refresh" and the web site comes right up. Anyone have any ideas as to why this occurs?

Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Go to System Preferences
Click Network
Highlight AirPort and click Configure...
Choose “By default, join: Preferred networks”
Select your access point and Remove your access point with the minus button.
Launch your keychain access in Utilities and delete your access point keychain entry.
Reboot
Go back to the “By default, join:” page and click the plus this time to add your access point. Enter the correct password, save, reboot.

Airport express not connecting to internet

I am switching from Clear to Comcast hopefully for faster, more reliable service.
Connected the Comcast modem directly to my Mac Mini, activated...voila on the internet.
Plug in Airport Express so that the Mini and my MBpro can share internet and a printer.
AE powers up,gives the green light, but no internet service.
System preferences>network states that WiFi has a self-assigned IP address of 169.254.xx.xx
that will not connect to internet.
With each reset the number changes slightly but still no internet. I tried a manual number or 192.168.xx.xx
and WiFi connects but still no internet.
1-1/2 hours with Comcast provided no help other than to call Apple. Is this really that difficult?
With Clear it was a snap, but I am at the edge of the coverage zone and it sometimes fades.
Please guide me through the steps.
Thanks,
JM

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref:Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Airport Extreme not connecting to Internet

Here's my setup:
imac with Airport Extreme in home office
Airport Express hooked up to home ethernet network in family room to stream itunes (or connect laptop at other end of house)
Just got home and tried connecting my work powerbook to the Airport Extreme network, and suddenly it does not work. Basically times out after trying to connect to internet, even though i get full bars signal-wise, and network diagnostic says i should be connected. I can connect to the Airport Express network in the family room just fine. And my internet connection is working fine over the ethernet network.
Has my Airport Extreme bitten the dust? It's showing full bars, but my Canon i960 stopped printing from it the other day. I thought that was just a problem with the printer, but maybe the problem is my base station?
ps running all the lastest software...
Any suggestions? (Tried restarting cable modem, Airport Extreme, computer, etc. No go.
Thanks for any help.

Hmmm... That's odd that you can't administer the Airport Base Station
from the portable computer (the one you'd later use wirelessly) and
essentially check the thing out thoroughly; see if the firmware and
other things are up to par and the settings are chosen properly.
You'd use the ethernet cable in either case, to access the Base from
the portable or the tower; when you are doing an occasional test and
reset of the Base station. Sometimes, details make a difference.
Another factor may be in how you have the Base station set up to
share internet among computers; the ethernet-only G4 that sees
the through-ported IP dataflow should also be able to administer
the base station. But it may require the Portable, hardwired, to
check the settings and get it to work. I had a similar issue once
with my primary AEBS and had been administering it via a non-
wi-fi B&W G3 tower on ethernet cable; the other computers were
all wi-fi. That worked out great. Currently, I alternately run the iMac
G4 via wireless, and sometimes by wire. I have both set up & ready
and only need to go into the control panel/system preferences; to
make a change. Sometimes the wireless telephone (2.4GHz) is too
close and kills the wireless to my desktop Mac; so I change to wire.
What kinds of addresses are you seeing in your set-up for IP
to each computer? Unless you do actual file-sharing between
them, you can set that up so each computer has a full ISP
address; not those 10.0... or 193.00. or other networking ones.
Sharing a printer is another matter, if you run your AEBS as
though it were a wireless router only, it would be trial & error;
if set up to be wireless printing you'd probably need to get a
wireless USB module to see if that'd work for the G4.
The deal you are talking about, above, is how the device
works. Your G4 tower sees the internet via the through-port
in the AEBS router; it is a wired & wireless router, plus it
can give you wireless printing because it has a USB port.
But only when it is set up correctly. That is easier to do
than it is to write about. When mine fails, I look into it;
and as I suggested in other posts, it will just work later.
PS: In your Portable computer's System Preferences/
Network control pane, see what order it shows the
items or pathways available to connect to the net are
in; if the wireless airport isn't at the top of the list &
is not activated, drag it there. The check-boxes by
each option of course, need to be activated as needed.
When you see a signal, it should be able to find the IP
if the other settings were correct. Sometimes, the basic
defaults work OK right out of the box.
In the portable's System Profiler, you could also see if
there is an assigned IP address given to the computer.
At that point, there should be no reason for it to not work.
Like I said, it is harder to write or talk about it; easier to
see the things and work the strings in the right order!

AirPort Extreme Not Connected to Internet

I have been trying all day to connect a new AirPort Extreme base station. The base station appears to be configured correctly, in that the green indicator light burns solid. But I can't connect to the Comcast Internet: I get an error message that the Ethernet cable is unplugged (it isn't). I've powered down, reset, and restarted the cable modem; and have disconnected and reconnected the power supply to the base station numerous times, but still no Internet. When I reattach the Ethernet cable directly to the Mac everything is fine. I can't tell whether or not the base station is pulling the IP address, etc., from Comcast. Anyway, I'm getting nowhere with this, and would greatly appreciate input from this discussion group. Thanks very much.

Hello driverdude. Welcome to the Apple Discussions!
Although I know you tried multiple resets, please try the following to see if this will get you Internet connectivity with your Comcast modem ...
Try the following, in order, checking for Internet access after each step, or until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AEBSn, & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AEBSn, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

Airport shows being connected but will not connect to internet

Airport will not connect to internet yet shows me as connected.
When and if I do get connected, I will loose the connection and unable to access the internet.
This has happened using several different wireless locations.
Please help as to what my settings should be or how to correct the problem

What debugging steps have you taken?
Connecting to your wireless network and connecting to the Internet are two different parts of the connection process.
If you open your Network preferences panel does it show you have an IP address of the form 169.x.x.x?

My macbook pro 15inch running on maverick when i try to click on wi-fi says no hardware installed please help i need wifi and and under network staus wi-fi is fail and under network airport is not connected can anybody help the wifi icon has a x and does

my macbook pro 15inch running on maverick when i try to click on wi-fi says no hardware installed please help i need wifi and and under network staus wi-fi is fail and under network airport is not connected can anybody help the wifi icon has a x and does not even let me turn it on

Have you attempted to reset the SMC? That would be the first step. Hold the left control, option, shift key and the power button for about 5 seconds and release. Then try to reboot. Might as well reset the PRAM as well. Hold command, option, P, R on start up until the machine restarts. If that doesnt' have any affect we'll have to dig deeper into a potential hardware failure.
If this method doesn't work, check the webcam that will tell the problem is on the iSight & WiFi cable. If your webcam is ok, then it'll be the WiFi card problem. Hope it can help ;-)
- xia_us9

My laptop compaq presario will not connect to the Internet anymore after buying airport extreme. Why? It detects the network, accepts my password, but will not connect to Internet.

My laptop compaq presario will not connect to the Internet anymore after buying airport extreme. Why? It detects the network, accepts my password, but will not connect to Internet. I tried to repair connection, tried to reboot modem several times, I even updated my computer. Nothing. All it says is that it does not detect modem. Why?

Welcome to the support community group.
First, are you sure that your AirPort Extreme has been configured correctly and is properly connected to your modem?
Begin by telling us how you have things connected and if the Airport Extreme is replacing a previously owned router or is this an entirely new installation?
First be sure that your modem is working and properly connects you to the internet using an ethernet cable directly connected to your laptop. Once you're sure that's working, reset the AirPort to factory defaults by disconnecting it from power and pressing and holding in the small reset button on the back for 15 - 20 seconds while you reconnect it to power. Then turn everything off for 5 minutes. Connect the Airport to your modem with and ethernet cable to the Airport WAN port on the back (check the user guide to make sure you connect the cable to the correct port) then connect a second ethernet cable between the laptop and one of the LAN ports on the AirPort Extreme.
Then power up the modem first, wait 5 minutes and then power up the Airport, wait 5 minutes and finally power up your laptop.
Then run the airport configuration utility from your laptop. Since you're not using an Apple computer, be sure that all of your firewall, and virus blocking and checking software is disabled before you run the airport configuration utility. Once you run the utility, it should detect your AirPort and allow you to use the configuration wizard to set things up.
Check back if you're still having problems.

My iMac does not connect to internet via wireless after I log in. I have to open network preferences and run the assistant everytime to make it work. Its a new system, updated to Mountain Lion,.

My iMac does not connect to internet via wireless after I log in. I have to open network preferences and run the assistant everytime to make it work. Its a new system, updated to Mountain Lion,.

Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
Or whatever Interface you use.

Hi, I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand new a while ago i was trying to connect to my home wireless network it said that your airport is not configured then I restarted the system but it didn't restart it shows the "

Hi,
I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
Your help is really appreciated"

Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help

Apple TV does not connect to internet over the WiFi network

I recently bought an Apple TV and hooked it up to my Sony 46" HD LCD TV.
My desktop is an iMac running Mac OSX Leopard
I have created a WiFi network using the AirportExpress conected to an ADSL router.
The wireless network is working fine and I have access to internet through my iMac or other PC and Apple laptops.
Yesterday, I tried installing my new AppleTV following the little instruction book. My problem is that while the AppleTV detects my network (it shows up as the network) and on choosing this network connects to the network but gives a message that it has not connected to internet.
As a result while it synchronises with iTunes on my iMac, it fails to download from the internet directly. I am unable to upgrade to the latest version or play YouTube or images from my MobileMe account or log on directly to the iTune Store.
I have tried figuring out the problem but unable to do so. Thanks for your help.

I am having a similar (or identical) problem. I have a network running on my airport extreme. My imac and my girlfriend's laptop can connect to the internet without issue. The apple tv finds my network and reports that it connects, yet it doesn't seem to. I cannot access trailers or youtube, cannot update, and cannot play purchased content. I reset the apple TV, but that did not solve the problem. Should I reset the airport extreme?

Trying to setup airport for 1st time and it will not connect to internet, we also did not create a new network and cannot find this option again

Trying to setup airport for 1st time and it will not connect to internet?

You might try doing a reset of your AirPort unit. Use a pen or paper clip to press in on the recessed reset button while you plug it in, then continue to keep the button pressed until the status light flashes several times,
For more advice, please describe all your networking gear.

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to.

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to. I can't find anywhere in the utility or network preferences that will allow me to choose this router as the default. How do I fix this? BTW I'm using Lion.

Are there any previous networks that you have used that have the same password as Molly? YES
Using System Preferences > Network > AirPort Advanced again, you need to remove any listings of previous networks that used the same password as Molly. Click the name of the network and click the - (minus) button at the bottom of the list of connections.
Also delete any other networks (except Molly at the top of the list) that might have used the same name...Molly in the past.
Delete any other networks that you no longer need so that your Mac will search for networks more quickly
Click OK, then click Apply
Open KeyChain Access and look for a listing of any old networks that you no longer need. Click to highlight the name of the network, then click the Delete Key on your computer.
Then look for any old networks that might have used the name Molly in the past and do the same for them.
Then look for any old networks that might have used the same password as the password for your "new" Molly network and delete them in the same way
Click the KeyChain Access menu just next to the Apple icon in the upper left corner of the computer screen
and then click KeyChain First Aid
Enter the main administrator password for the Mac you are using and highlight the Repair button. Then click Start. You will see a message that repairs have been completed
Quit Keychain Access
Power down the entire network...all devices...order is not important
Power up the modem first, then your main router, the other devices one at a time
Log on to Molly and see if the Mac remembers it after a few tries. If not, I'm afraid that you will need to change the name of the wireless network and password on your router due to corruption issues on the Mac. You have done everything possible without re-installing the complete operating system.

Green light on Airport Extreme but will not connect to internet

I have tried restarting computer and Airport Extreme but it will not connect to internet. Unit has been working great up until now. I have made no changes in system.
This Airport/time machine is 2009 version.

The Cisco DPC 3010 is a cable modem, so you will need to let the modem completely reset before you connect it to the AirPort Extreme.
It may be necessary to perform a Factory Default Reset on the AirPort Extreme and reconfigure it, but we will try a shortcut first to see if that can be avoided.
Power off the entire network.....all devices....modem, AirPort, computers, mobile devices, etc in any order that you want.
Be sure to disconnect the power cable on the modem, either on the back of the device or pull the power cord from the wall AC jack
Leave everything powered off for at least 30 minutes. Longer is better, as it sometimes takes the equipment back at the ISP longer to completely reset and issue a new fresh IP address to the modem.
After the wait period, power up the modem first, and let it run for at least 5 minutes by itself. If your modem documentation states that the modem should be powered up for 15 minutes, then go with 15.
Power up the AirPort Extreme next, and let it run a few minutes
Then power up other devices one at a time about a minute apart
When the entire network is back up, check the network.
It this does not work, you will have to start over again as above, except this time you will need to perform a Factory Default Reset on the AirPort Extreme.
To do that, power off the AirPort Exterme for a few minutes
Hold in the reset button on the back of the Extreme.....and keep holding it in for an additional 9-10 seconds while you simultaneously plug the power back into the Extreme
Release the reset button after the hold period, and allow a full minute for the Extreme to restart to a slow, blinking amber light
Power off the AirPort now, and start it back up in the proper sequence
If things still don't work, then you likely have a defective AirPort Extreme that will need to be replaced.

My airport is not connecting to the internet. I have a cable modem. and i'm on the internet now connected directly to the modem. what can i do?

my airport is not connecting to the internet. I have a cable modem. and i'm on the internet now connected directly to the modem. what can i do?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

My Airport does not connect to network from Windows laptop, but guest network does connect to internet

Similar Messages

Maybe you are looking for