My airport express is stuck with a solid amber light.

I have reset via hard reset instructions and also factory default by holding in the reset button while plugging in the device. My internet connection works fine when I hard wire connect it to my mac but airport utility will not recognize the airport express

My AirPort Express is stuck with a solid amber light.
If that is the case, and several tries at a Factory Default Reset have not been able to free up the lockup, then it is unfortunately likely that the AirPort Express has experienced an internal electronic component failure and will need to be replaced.

Similar Messages

Lost Airport Express in my network. Solid amber light.

I've an Airport Extreme base station and use an Airport Express to extend the range throughout my house. Yesterday I had to restart Airport Extreme and reset it back to default mode, to make it burp out a 'stock' IP number. I renamed my network; but now my computers, using Airport Utility, can't 'see' the Airport Express. And its light is now solid amber. How do I get Airport Express back into my network to extend my range? Thank you. (BTW: I can't find the Airport utility disc that came with Airport Express.)

Welcome to the discussions!
If you reset the Extreme back to factory defaults and reconfigured it, you will need to do the same for the Express.
Plug the Express into power and hold in the tiny reset button until the amber light begins to blink rapidly.
Open AirPort Utility to reconfigure your Express to "extend" the network created by the Extreme. If Airport Utility can't "find" the Express, temporarily connect an ethernet cable from the Express to your computer.
You may find it a bit easier to use the Manual Setup option on the Express since you already know how your Extreme is configured and you will use many of the same settings.

I have a new Airport Extreme and an old airport express. I am getting an amber light on the new Extreme and a green light on the Express. I have internet no problem but the status light is blinking amber

I have a new Airport Extreme and and old airport express. I am getting an amber status light on the Extreme and a green light on the Express. The Extreme is blinking amber all the time.
I have internet and everything seems to be working.
I have reset and pulled the power cord on both the extreme and the internet block
How do I make it Green?

If things seem to be working OK, but the amber light is flashing......the AirPort Extreme has a message for you. To see what that might be......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon
Click on the amber dot in the small window
It might be a message that a firmware update is available for your AirPort Extreme.

Airport Express - status repeatedly cycling from solid amber to solid green

Hello, my Airport is cycling solid green to solid amber approximately every 5 minutes or so. Any insight would be greatly appreciated! Thank you.

Perform a Factory Default Reset on the AirPort Express
Resetting an AirPort Base Station or Time Capsule FAQ
After the Express restarts, it should blink amber slowly. If you try the Factory Default Reset a few times and the Express will not blink amber slowly after it restarts, you have a defective AirPort Express that will need to be replaced.

Airport Express initial set-up failure (blinking amber light)

Hi there,
I probably should've gone for a walk before posting this but I am just effed off with a supposingly simple set-up that dont follow through...i guess this will probably end being something daft my end, either not reading the instructions or just having apples (no pun intended) and oranges as regards my hardware/software and overall intentions.
Ok...premise, I just want to use the Airport Express (AE) to link my laptop (hosting iTunes) to my HiFi using the AE. Laptop is a recent lenovo running Windows XP, I have a working WiFi connection. Accoridng to some earlier checking, due to its XP nature, I have loaded AE Utility 5.5.3 onto my desktop. The AE has its power cable in and is loinked to my HiFi with a jack plug cable.
Issue, the AE only gets to a 'flashing amber stage' in the start up and the AE Utility (AEU) does not locate the device in its scan. The help indicates that a lot of unplugging and re-starting/setting should be attempted or to check with the AEU for help; however, this has failed to change any status.
Does anyone have any ideas on how i can get this £80 plastic paperwieght to step up?
Cheers all, happy 2013 ;-)

The AirPort Express will "join" virtually any wireless network if it is provided with 3 correct settings:
1) The name of the wireless network being joined....I assume that you already know this
2) The password of the wireless network being joined....I assume that you already know this
3) The exact type of security settings of the wireless network being joined.....this is where users have difficulty with the AirPort Express setup....because they either use the default settings on the Express (which may likely not match the settings on your wireless network), or they guess at the wireless security setting (which do not match the security settings on the wireless network).
So, the main question here is.....do you know exactly what type of wireless security that your network is using? The Express must be provided with those exact settings in order to join the network correctly.
You will need to perform a Factory Default Reset on the Express and then start over with the configuration again.
Power off the Express for a few minutes
Hold in the reset button first, and keep holding it in for another 9-10 seconds while you simultaneoulsy plug the power back in to the Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light

HT1515 My new Airport Express will not stop blinking an amber light. What should I do?

I can't seem to get my new Airport Express set up properly. I've connected wifi cable from the modem, the USB printer cable and plugged in but it continues to blink amber. I've tried all the solutions mapped out in the instructions. What could be wrong?

Thank you so much for your reply. I went over the AP utility and reread the notes and solved the issue! Now, I need to solve a printing issue - I have two laptops, two Ipads and my Imac in my network and I would like them all to be able to print using my HP printer. Working on that now!!!

Airplay won't connect to my Airport Express & is intermittent with Airport Utility

Hi
Yesterday, my iTunes 10 stopped connecting via Airplay to my Airport Express. It spent a long time displaying a Connecting message, then finally gave me this error message: "An unknown error (-15006) occurred while connecting to the AirPlay device AirPort Express”.
I have a Macbook Pro 2.5 Ghz Intel Core i5 (6 months old). 4 GB 1600 MHz DDR3.
Running OS X 10.7.5.
My main modem/router is a Livebox and I usually going my Airport Express to the Livebox network to play music.
My Airport Express is 802.11g
All my equipment is within a radius of 2 or 3 feet.
I'm aware of at least one other recent thread about this problem (https://discussions.apple.com/thread/4150757?tstart=0), but none of the solutions suggested have resolved my problem, so I have summarized a list of the actions I have so far taken to try and resolve the problem. Hopefully, this will help others sort this issue out for themselves.
ACTIONS TO SOLVE ISSUE
1. Ran Airport Utility 6.1, which was unable to find my AX.
2. Downloaded, installed & ran Airport Utility 5.6. AU 5.6 still couldn't find my AX, giving me this error message:
"AirPort Utility was unable to find any AirPort wireless devices. Make sure the AirPort wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
3. Unplugged the AX and did a hard reset. AU found my AX and I configured it to join my Livebox network. After being configured, the green light came on the AX, which also appeared on the AU list of devices. However, AU still had the message "Waiting for Airport Express to reset…" with a spinning ball for several minutes. So, I closed the AU window (as AU advised), and reopened it. Happily, the AX was still listed.
4. Reopened iTunes and tried to select my AX as speaker output. At that exact moment, the AX vanished from the AU list of devices and, after the long wait, iTunes gave me the same error message as before:
"An unknown error (-15006) occurred while connecting to the AirPlay device AirPort Express”.
When I tried to rescan for devices in AU, I got the same error message:
"AirPort Utility was unable to find any AirPort wireless devices. Make sure the AirPort wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
5. Hard reset and configuration of AX. This time I didn't close the AU window, I waited for the AX to reset. When the spinning ball finally vanished, I got this error message:
"An error occurred while reading the configuration. Make sure your Apple Wi-Fi base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)"
6. Apple help pages suggested updating the AX firmware. I downloaded the firmware update, did the AX hard reset/configuration routine, then tried to run the firmware installer and got this error message:
"An error occurred while attempting to communicate with the AirPort Express. (-8)"
7. Ran all the software updates, including upgrading to iTunes 11.
8. Spent over 5 hours doing many many hard resets of the AX, combined with iTunes restarts, MBP restarts etc. Along the way, I discovered that if I hard reset & configured the AX, after a few minutes, AX would disappear from the AU device list without me doing anything.
9. Attempted to change IPv6 options, using following methods:
a. System Preferences -> Network -> Advanced -> TCP/IP -> IPv6 _> Link-local only
b. In Terminal.
networksetup -listallnetworkservices
networksetup -setv6off Wi-Fi
Neither method had any effect on the ability of AU to see my AX.
Phew! I'm now exhausted & rather demoralised. Anyone got any other ideas?

I have been dealing with this for days now. I'm not sure what the solution is either, I've spent most of my vacation from work attempting to get it to work with my speakers and printer, none work still!!
It seems like a lot of ppl are dealing with these errors but there isn't one solid solution out there.
Try to set the AX wirless setting to "off" and only have it work for Airplay, Does it work for you?
One last thing, could this be an update problem? As in, you update your firmware/software and it renders the AX obselte. My AX is old probably a little older than 4-5 years, what about your?
I would really like to get this to work as I do not think I need a new AX to make this work.
Let me know your thoughts.
B.

Airport Express not working with Comcast

I used to have AT&T and had my airport working well. Yesterday i changed to Comcast and my airport is not working the light stays yellow.. I tried resetting it but it didn't work.. I use it with my old Cisco router and its working. Whats wrong with my Airport Express? My computers are Windows 7

A solid amber light indicates that the AirPort Express has locked up....or it is defective.
Suggest you that try a Factory Default Reset as follows:
Pull the Express from power
Let it rest for a few minutes
Hold in the reset button and keep holding it for another 8-10 seconds while you plug the Express back in to power
Release the reset button after the hold period and allow 40-45 seconds to restart
The Express should display a slow, blinking amber light at this time
If you continue to see a solid amber light after a few tries with a Factory Default Reset, the Express has failed and it will need to be replaced.

HT4587 I downloaded Airport Express Utility 5.6 to get my Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility.

I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?

It is likely that you downloaded AirPort Utility 5.6.1. If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion

Can't Get Airport Express To Work With ATT's Uverse

For years, AE worked just fine with my 2Wire portal streaming music to my stereo. Went to Uverse 2 months ago, and AE quit working. I am not using an Airport base station, just the Uverse modem and I need help getting it to work.
There is nothing in this forum when I search for uverse, so I post this in hope someone can help me.
I reset AE it and it finally appeared in Airport utility with a yellow light. I click configure and when I choose to join my current network, it sets up it's own Apple network, removing it from Airport utility and changing Airport status in Network to yellow.
No matter what I do or how I try, I just can't get AE to work with the stock 2Wire modem.
Has anyone been able to get AE to work with just the 2wire router & not have to buy an airport base station.
Any help is REALLY appreciated, as I wanna hear my Christmas music, and it's turning me into a Grinch!
Thanks!
Message was edited by: Chris Winkler1

+However, it asks for the security and all I see is WEP in the Home Network set up, I don't know if it's 40 or 128+
AT&T set this up, so only they can tell you for sure. My guess would be WEP 128 since this type of security is stronger than WEP 40.
+And it asks for a wireless password. I entered the one from the router & it did not work. Tried the Key and it did not work.+
This is the same wireless password that you would use if you were logging on to your wireless network with your computer. But, unless you first have the exact, correct security setting for your 2wire router, the password will not work.
+Has anyone out there successfully got their Airport Express to work with Uverse????+
I don't provide instructions to anyone on the forum unless I've first done it myself. I'm providing you with the same instructions that I used to help a neighbor with his 2wire Uverse setup last week. It works fine.
But, he called AT&T to ask them what security setting they used on his 2wire router. Otherwise, we would have had to try each possible setting to see if we could make it work.
AT&T also told him that his password should be 13 characters, all lower case letters with no spaces. That is what the neighbor said he used. I cannot confirm this as he did not share his password with me.
AT&T may have set up the password criteria differently on your router. You need to confirm with them on this.
+What password goes in the Base station tab, Key or Password?+
Any password you want. This is a separate password simply to be able to access the settings on the device in the future when you are using AirPort Utility. You could use your wireless network password if you want.
Please post back on your progress.

HT1515 How can I use Airport Express (1st generation) with OS X Mavricks?

How can I use Airport Express (1st Generation) with OS X Mavericks?

1st Generation AirPort Express will work fine with Mavericks.
Are you sure that you have a 1st Gen Express?
Check the model number on the side of the Express. 1st Gen is A1264.
If you see A1084 or A1088, these are much older versions of the Express that were sold long before Apple began to use the Generation naming with "n" wireless devices in 2007.
Mavericks will not support the A1084 or A1088. Use another Mac running Leopard, Snow Leopard, or a PC if you need to administer the older Express.

Airport express not working with apple products

We have been trying to get airport express to work with a macbook pro, ipad2, iphone, laptop, htc wildfire - havent even tried the air music or printer yet!
We have a green light on the airport express which is connected to an ntl cable modem(virgin media network).
Currently the only thing that will connecy is the laptop and my htc phone. All the apple products will not connect?
We went to the apple store today and it worked grand when it was plugged in - the apple products all worked.
The network comes up on ipad2 but when you press connect it says 'unable to connect'
can anyone help us please?
thank you

I have the same issue. Mine fixed itself for a bit and now it's broken again. I'm thinking it's going to be intermittently broken. I've tried turning both devices off and on again but that did not help.

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

Hello Hornet12,
Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
Using AirPlay
http://support.apple.com/kb/HT4437
AirPlay requirements and capabilities
To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
Stream content from
Requirement
Notes
iPad
iOS 4.3 or later.1
From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
iPhone (3GS or later)
iPod touch
(2nd generation or later)
Computer
iTunes 10.2 or later.
Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
Apple TV
Apple TV software version 5.1 or later.
Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
Cheers,
Allen

HT1998 what is the latest update for Airport Express 802.11n with the Mac OSX10.6.8

what is the latest update for Airport Express 802.11n with Mac OSX 10.6.8?

You can find out as follows:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the AirPort Express
Click Manual Setup
Click directly on the word Version (3rd line)
If there are any updates, you will be notified.
If there are not any updates, you have already have the latest firmware.

Apple AirPort Express Base Station with 802.11n - MB321LL/A. How to set it up to my new iMac

Community:
How do you set up an
Apple AirPort Express Base Station with 802.11n - MB321LL/A how do you set up on Mac running on OS X 10.9.4?
Please advise
Fmsalazar

Apple did say it was important.
If the units do not show up in the airport utility then you must set it correctly to link-local.
Steps for OS X Lion or Mountain Lion
This can happen if IPv6 has been disabled. To enable IPv6 for your network interface:
Choose Apple menu () > System Preferences, and then click Network.
If a lock icon appears in the lower-left corner, click it and enter your admin name and password to unlock the pane.
Click your network service (Wi-Fi or Ethernet) in the list, and then click Advanced.
Click the TCP/IP tab.
Choose Link-local only from the Configure IPv6 pop-up menu.
Click OK.
Click Apply.
AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
Apple rep says the same.
Re: Unexpected error when connecting Airport Express A1264 to Airport Utility 6.3.1
I am searching as I saw it in a thread today where a person had issues. (No contribution from me in the thread but found that was the issue).
It is kind of a fail safe.. since auto can end up with any setting.. and it will depend on the setting of ipv6 in the Airport Router if it works properly in the computer.. setting it to the correct value is one step in sorting out problems when people get in a mess.

My airport express is stuck with a solid amber light.

Similar Messages

Maybe you are looking for