My airport extreme is flashing amber it says i need a ip address .... it was working just fine yesterday until i had to reboot cable modem how do i get my extreme to work again so i can have wireless
my airport extreme is flashing amber it says i need a ip address .... it was working just fine yesterday until i had to reboot cable modem how do i get my extreme to work again so i can have wireless..... please help!!!
Hi again Jen,
Most internet providers utilize "dhcp" -- you might want to check to see if your extreme is set to that function.
If you want to try, you need to go into airport utility and select MANUAL setup/ then click NETWORK button on top of the window. /select TCP/IP -- make sure that you see "Using DHCP" not MANUAL in the configuration window. If you do see using dhcp, click the renew dhcp lease button. Then you'd have to do the power down/up cycle again. If all this doesn't work, you can do a hard reset on your Extreme, which will bring it back to the way it came out of the box, then go through the same proccess that was used to set it up originally.
Similar Messages
-
My iPad won't connect to my wifi anymore. Was using it and it just quit. It is not my wifi because my daughter's iPad works just fine. I've turned it off and back on, reset, forgot this connection and nothing works. Help???
1. Turn off router for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings -
My camera just recently went blurry. It was working just fine yesterday but then I went to use it today and the pictures are so fuzzy. Has anyone else had this problem with their iPhone 5?
1st... make sure nothing's covering/smudging the camera lens. then...
Standard troubleshooting...
Try a reset by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.
Remove the Camera app from Recently Used list...
- From any Home Screen, double tap the home button to bring up the Recents List
- Tap and hold any icon in this list until they wiggle
- Press the red to delete the Camera app from this list.
- Press the home button twice when done.
- Restart the Camera app
If still a problem restore with your backup.
If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
If still a problem, it's likely a hardware issue. -
how do i get my ipod to turn on after i tried everything i cant even get it to charge
Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
How do I get my Canon MX860 back online so I can print wirelessly on my Mac OSX 10.8.4?
I recently installed a new and bigger Time Capsule on my MacBook Pro system and since doing so, I lost the ability to print wirelessly on my Canon MX860 printer. I am using Mountain Lion OSX 10-8-4.
I note Pahu discussion in another group on this same issue but it pertains to Snow Leopard. I don't know how much difference it makes but when I followed his instructions, I did not get my problems resolved. I am inserting here his discussion and in bold my comments where my results differed.
Pahu comments follow (min results in bold): Some of the new models of Canon inkjet let you set the network settings using the touch panel on the printer. I am not sure if your MX860 has this setting, called Easy Setup under Device Settings > Network. If it does then you can change the network settings and create a new print queue on the Mac.
If it doesn't have the ability to change the settings via the keypad then you will have to connect the printer via USB to your Mac, which will create a USB connected print queue. If you then open Print & Fax, select this USB MX860 print queue and then press Options & Supplies, you will see the Utility tab. I DID NOT HAVE THAT TAB I FOLLOWEED HIS LEAD USING THE FOILLOWING: MAC HD/Library/Printers/Canon/BJPrinter/Utilities With this selected then click Open Printer Utility. This will open the Canon IJ Printer Utility and within this utility you will see the Network Settings button. Select this and you can then enter the new network settings, such as the SSID, type of security being used and the password for the network. Save the changes, turn off the power to the MX860 and then disconnect the USB cable.
Now turn the printer back on and open Print & Fax again. For the USB print queue you just created, you can delete this. I NEVER SAW ANY PRINT QUEUES AFTER TURNING THE PRINTER BACK ON. ONLY THING I HAD WAS THE PRINTER LISTED IN THE WINDOW SHOWING IT WAS OFFLINE. And for the old networked print queue, you need to delete this also. You may also need to delete the networked scanner queue if you had one. So with all the old queues to the MX860 removed you can then add the new network printer. I DID TWO THINGS, FIRST LEAVING THE PRINTER IN THE WINDOW, I TRIED ADDING USING + BUT NOTHING HAPPENED. THEN I TRIED DELETING THE PRINTER IN THE WINDOW AND THEN TRIED HITTINH + BUT NOTHING EVER APPEARED. HAD TO RECABLE THE PRINTER TO THE MACBOOK TO GET PRINTER BACK. Click the + and wait for the MX860 to appear as a printer - it will appear first as a scanner and you can either add that now or after adding the printer. NONE OF THIS HAPPENED AND I LET IT SIT FOR SEVERAL MINUTES. Several seconds after the scanner appears the printer should also appear, showing canonijnetwork in the Kind column. DID NOT HAPPEN. Select this and the Print Using menu should automatically select the Canon MX860 series printer driver. When it does click Add to complete the network print queue creation and repeat the steps to add the network scanner if you need it. OBVIOUSLY, NONE OF THIS HAPPENED EITHER.
NOW IT IS ME AGAIN. Can someone please help me with this mess? I am so frustrated with dealing with this for three days and the only way I can print is using the RSB cable which is not so cool strung across my bedfrom the computer to the printer. Any guidance would be appreciated. I am an old man of 73 and way over my head with this mess. Don't know why Canon has to make this so difficult. Thanks in advance, Ron WikoffI too am experiencing the same problem, my Canon MX860 printer is no longer connecting to my Airport Extreme Router. I tried following the directions on Canon's website http://www.usa.canon.com/CUSA/assets/app/pdf/wireless/router_network_change_mx34 0_mp495_mx860_mp980_mp620_mac.pdf
I have tried uninstalling all of the printer drivers, as suggested in another apple discussion, then running the Canon IJ network tool.
I tried PAHU's response above:
Okay. No facility to add the MX860 to an Apple wireless network using the control panel so you will need to use the Canon IJ Network Tool.
So with the Mac connected to the MX860 via USB cable, open Canon IJ Network Tool (which should be located in Applications > Canon Utilities > IJ Network Tool). If you are looking in the other path you mention above, this could be an older version so download and install this latest version of the IJ Network Tool.
With the IJ Network Tool open, the first window talks about adding the printer to the network. Ensure the setting "Use the printer on the network" is set. Click OK
From the next window, the MX860 should be shown and as connected to the Mac via USB. Select it and click OK.
The next window will show the utility searching for wireless access points. A new window will then appear asking you to confirm the connection to the access point and the text will show which access point was found - which should show "Ronald Wikoff's Network". Click Yes to continue. When a window appears stating that the Canon IJ Network Tool wants to use your password, click Allow. (I cannot make it past this step. The Canon IJ Network Tool does not aoutmatically find my password. Instead I am taken to a screen where I type in my password and then attempt to connect.)
Now the window will take several seconds to setup the printer and should show a Setup Completion window. Click OK. (I never make it to this window. I receive an error message that that says the printer cannot communicate with the access point and to check the password. I checked the password then tried again. I even changed the password in the airport utility to make sure I had the correct password and it still did not work. I am starting to suspect that this may be related a recent Airport utility upgrade to 6.3.1 a few days ago.)
This will make the Add printer window appear. In the list, the "Canon MX860 series (00.00.85.xx.xx.xx)" should be visible. If it is, select it. The "Use" menu should then show "Canon MX860 series". If it does, click Add. This will add the network printer to the Mac.
If you now open Print & Scan, the "Canon MX860 series (00.00.85.xx.xx.xx)" should be in the printers list, as well as the Canon MX860 series. This latter one is for the USB connection. You could delete this printer and disconnect the USB cable.
The last step is to print a document to this network printer.
I plan on calling Canon tomorrow but if you have any other options for my to before then I am open to suggestions. -
My photos are appearing in last import, last 12 months and in my events (in library) but not in my photos (in library). I have never had any problems up until about 3 months ago. Did I change a setting by accident? I prefer to view my photos in 'photos' as opposed to 'events'. and btw, all the dates seem to be correct on the past recent months.
Post in the iPhoto foum.
https://discussions.apple.com/community/ilife/iphoto -
My iTunes library is on a HDD attached to the USB port of the Airport Extreme. We tend to run iTunes on my wife's MacBook and use Remote on our iPads to play music and interrogate the library. Ther connection from the MacBook regularly drops and iTunes defaults to the MacBook HD location for the library. When connection is restored, it therefore requires a rebuild/reload of the library, which can take some time, as it is over 70Gb. This time connection has been lost, the Airport Extreme is flashing amber and none of the Airport Utility programs on either of our MacBooks or iPads can see it. Can anyone advise as to how I get access to my iTunes library?
Since I can't seem to reset it here with the computer I have, can I take it to the apple store to reset it, and then bring it home to use it?
The old Express must be able to "see" your wireless network to "join" it, so unless you take your main wireless router with you to the Apple store along with the Express, things won't work.
The Apple Store might have a Mac running Leopard or Snow Leopard....but I would make an appointment first before I hauled everything down to the store.
Things would be much easier if you could invite a friend over to your house who might have a Mac using Leopard, or Snow Leopard, or a PC.
It would only take 5-10 minutes to get the Express configured.
Or, should I jsut buy a new one? And, if I am buying a new one to stream music, shouldn't I just go ahead and get apple tv (I think the price is very similar)?
Sorry, I can't tell you what is best for you. Talk the folks at the Apple Store to get some opinions.
If it were me, I would get a new Express. Careful on the AppleTV as it only has a digital audio output..... that may or may not work with your existing equipment.
http://www.apple.com/appletv/specs/ -
I have an Airport Express, which flashes amber, but when I go to manual set up, it says there's an error and tells me to close configuration? Once I complete that, the same thing occurs, and there's another error message?
Is this a new AirPort Express, or one that you have had for some time that has now developed problems?
What function do you want the Express to perform on your network? -
Hey Guys!
I just got my AirPort Extreme Base, but I can't use my HP Deskjet F4580 wireless printer with it.
The printer is not connected to the AirPort Extreme's USB port. It is placed in another room, and I'd like to use it (the printer) wirelessly (not connected to the USB port os the AirPort Extreme), as I used to. There is no place for the printer close the AirPort Extreme. It worked just fine with my previous wireless router (Linksys WRT54G). I'm very disappointed with the AirPort Extreme Base Station because of that!...
Can you help me? Please?!
Thanks Folks!This must be a tough one, no suggestions at all.
-
I have a 25" 2.8 GHz Intel core 2 Duo working on OS X 10.8.4, within past 2 days we've had the black screen and the white screen, we are up and kicking again but I can leave the computer playing music from iTunes, but within 10 minutes the screen is back, yet the music is still playing in the background. I can't get rid of the black screen unless I force quit the computer, then it starts ok. Then the process starts all over again.
I have a 25" 2.8 GHz Intel core 2 Duo working on OS X 10.8.4, within past 2 days we've had the black screen and the white screen, we are up and kicking again but I can leave the computer playing music from iTunes, but within 10 minutes the screen is back, yet the music is still playing in the background. I can't get rid of the black screen unless I force quit the computer, then it starts ok. Then the process starts all over again.
-
I have iPhone 4, it was working just fine..no I have a problem: it keeps searching for the network and then says no network..it was open to clean from inside..how can I fix the problem
Tap Settings > General > Reset > Reset Network Settings
If that doesn't help, try here > iOS: Troubleshooting Wi-Fi networks and connections -
The message function on my Ipad just quit working. I was using it while in Mexico and it just quit. I have come home and synced my Ipad with Itunes and function still does not work. How do I get this function to work again?
When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.
-
I had an imap account in my iPad and my iPhone 4. They worked just fine till about Christmas. They act like they are checking the mail and it shows there is mail to come in, but it just goes back to saying checking mail. Can't send mail either.
Update to above question:
Hello All,
To anyone with the same problem described above, on THEIR iPad (if it is running iOS 7.0.2):
Go to Settings; Mail, Contacts, Calendars; DELETE your *******@btinternet.com e-mail account, that you originally set up either using 'Other', or the 'BT' option which I am sure was in the list previous to the iOS 7 update.
Then ADD a NEW account choosing YAHOO from the list of options. DO NOT USE 'OTHER'.
Enter the correct details just as you (almost certainly) had already done in your previous attempts using 'other'.
When you see the 'verifying......' and 'the blue ticks' you should be able to exit settings and open your mail app and then receive all your 'old' e-mails again, AND be able to SEND as well.
All my 'old' e-mails, were NOT found in the 'old e-mail' folder though. THEY are still in my inbox.
So this fix worked for me.
After I deleted my account from 'OTHER' and put it in Yahoo, I like other people also ended up with more folders.
I hope this works for you on YOUR Apple devices.
Bob -
I have had a reinstall nightmare getting my loops back they are in the apple library, I can access them through the media browser but I only have a few available through the loop browser, how do I get them all back there again? please help
"Where do I find my hundreds of dollars of downloads I have done since 2005?"
They will only be where you put them If you are doing the very basics, then they will be on your computer and they will be in your backup copy of your computer.
The itunes store is not global at all, never has been. You cannot redownload your content from another country. You can only use the countrys itunes store for the country that you are physically located. -
My Bluetooth USB wireless transmitter for my portable BT speakers has quit working. Preferences says, "The selected device has no output controls", it used to work just fine. The internal and a pair of wired external speakers work fine. Can anybody help?
Just tested something and it worked.
If I put the headphones all the way in, the mac recognizes it as a digital output.
But if i don't put it all the way in, it recognizes it as headphones and works perfectly.
It's probably this crappy headphones.
If anyone has the same problem, try this out.
Maybe you are looking for
-
Hello, I just installed a the new AirPort Extreme connected to wired Ethernet as a Server for USB-Harddisks. Unfortunatele, it seems to work very unstable. I want to use the connected disks with an iMac G5 and an MacMini Core Duo. Sometimes the Extre
-
Does "cropping" a clip affect the max resolution it exports at?
This might be a silly question. I have a project that's made up of a bunch of clips that were all shot in 1080p. I cropped one of them, by a little bit. When I export it, the whole movie appears in 720p. When I uploaded to YouTube, also, the max r
-
It is me again. I need some more help. I want to put the four buttons at the south border, and I want to put the image at the North Center. Now I want them obviously to be on the same panel. I would also like to add them all at once like in my code.
-
Accounting document through MR21
Dear Experts, My user just performed price changed through MR21. My question is, why no Accounting document created after executed. There was only 'price change document appears after checked through CKMPCD. Please advice. Thank you in advance.
-
hi I must change server name (ERP 2005, MS SQL). Could you give me some advices ? I know that backup databases will be my first step adam