My Airport Extreme just stopped working. The message says ethernet cable not plugged in, but it is. Cable modem works fine. Is this a common problem?

My 2-year-old Airport Extreme instantly stopped working last night and is flashing the status light. The problem description is that the ethernet cable is not plugged in... however, the ethernet cable is still plugged into the cable modem. I checked the modem by plugging directly into my laptop... it works fine. Is this a common problem? Is there anything I can try other than sending it in for warranty repair?

At this point, before sending it back, I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Similar Messages

Unable to "share" a photo. Get error message stating server is not responding. But all normal email functions work just fine.????????

unable to "share" a photo. Get error message stating server is not responding. But all normal email functions work just fine.????????

Just a quick bump... Anyone got any thoughts on this?

After 5.1 install my video out cable will not work. Message says it is not supported! Any fixes?

After installing OS5.1 my video out cable stopped working. Message says it iis not supported! Any fixes. I re booted but didn't help.

Tried cleaning the connector with electronics spray and then spray air but didn't help. I get no audio or video, just the message that the accessory is not supported.

I have been transfeing my DVD footage to I movie using handbreak and the spinning wheel of death has arrived and locked up I movie as I tried to import footage. The message says, "Optimizing movies, processing event DVD" but I can't get out of it.

I have been transfeing my DVD footage to I movie using handbreak and the spinning wheel of death has arrived and locked up I movie as I tried to import footage. The message says, "Optimizing movies, processing event DVD" but I can't get out of it.

Yes I held them down till the apple logo appears, then spinning wheel and repeated boot up process. I only knew it was going round in circles because the charging sound kept repeating every so many seconds.
I am downloading iOS.5.0.1 now to do a complete factory restore. I hope this works. I have been looking online for hours for fixes and I have very little batter on it as its been spinning for hours now.
Why do things like this happen? I am sat there watching tv and one minute the settings folder is there then its not! How does that happen? It just disappear? I hadn't moved it to another folder or deleted it, it just.... went!

After download itunes installation began in windowx xp near the end of the installation the message says: it was not possible to write the value to the key Software / Classes / .mpg / OpenWithList / iTunes / .exe. Already reinstalled 3 times and always sa

After download itunes installation began in windowx xp near the end of the installation the message says: it was not possible to write the value to the key Software / Classes / .mpg / OpenWithList / iTunes / .exe.
Already reinstalled 3 times and always says the same message.
thank you

Only two had virus on windows XP this week and wiped them with Avast. The itunes asked me to install the update, and so I did. but it always gives me that message.

TS1424 I keep getting the message (song name) was not copied to IPod Ipod because it cannot be played on this ipod. Could someone tell me what this means? I have never had this problem.

Hi, I have been trying to down load some music to my Ipod. I keep getting the message: (Song name) was not copied to IPod IPod because it cannot be played on this I pod.
Can anybody help? I have never had this problem before.

brackenfromrincon wrote:
Is it something about "I Shot the Sheriff" that my iPod has a moral disagreement with? It had no issue importing and installing Body Count's "Kop Killa"...
Not really likely, is it?
First of all, look on the iPod to see if the song is actually on there. (The last Sync of my Classic resulted in "song not copied... because it cannot be found." The song had previously been on the iPod. I checked and despite the fact that iTunes could not find the file, the song was still on my iPod. I checked the folder and the song was exactly where t was supposed to be. So I simply set iTunes to find it again. What happened? I don't know, iTunes simply threw a wobbly!)
Second, try another Sync. Does this change anything? If the song was on the iPod, does a second Sync remove the message? If the song was not on the iPod after the first Sync, does the second one put it on there?
What happens?

ITunes music files cannot be edited, and new music files imported. The messages says I do not have enough access privileges even though I am the administrator of the system.

Since installing the latest version of iTunes all my music files cannot be edited, and I cannot import new music files into iTunes. The messages says I do not have enough access privileges even though I am the administrator of the system. If anyone can help me sort this out I would be really grateful. I have checked the read and write privileges for all the iTunes folders and it all seems in order so I can't understand it.
In general, I am getting really frustrated with Apple. They seem to be getting ever more controlling in their approach to their consumers. I need to edit music file information as I am a dj. And why can't I import music, unless I buy it from iTunes? Most of all, why can't I use the devices I paid a lot of money for in the way I want to use them, and not be forced to coerced to use apple's fee paying services (iCloud, iTunes).
I have used apple computers since the early 1990's, but in the last year I have gotten rid of my iPhone and my iPad and replaced them with Android devices. Much better and much less control. Perhaps it is time to switch from Apple altogether.

Hi
Read this About Disk Utility's Repair Disk Permissions feature
and OS X Mavericks: If you don’t have the correct permissions to open a file or folder
Does this help?
Jim

My airport Extreme just stopped assigning IP addresses to wired devices

I have an fairly large home network that is run by an Airport Extreme.
- Comcast Cable Modem for 3 public (not static) IP addresses
- small switch to be able to obtain three addresses
- Apple Airport Extreme connected to the switch and it receives an IP address and internet connectivity from Comcast
- Airport Extreme connected to a 16 port Cisco switch to handle the wired connections in the house. I have 54 ports of which 9 are currently in use.
all wired devices connected through the wall and a patch panel to the Cisco switch.
The issue is that after working flawlessly for about a month (just moved into this house) it stopped today. any device going through the hardwired Cisco Switch is no longer getting an IP address from the Airport Extreme.
I replaced the switch with a second one to see if that was the failure and it is not.
I unplugged the Cisco Switch from the Airport Extreme and plugged devices directly into the Airport Extreme 1 by 1 and they were able to obtain IP addresses.
I need more than the three ports available on the Airport extreme.
What changed and what do I do?

I unplugged the Cisco Switch from the Airport Extreme and plugged devices directly into the Airport Extreme 1 by 1 and they were able to obtain IP addresses.
This tells you that the AirPort Extreme is working correctly and the issue....whatever it is....is appearing after the AirPort Extreme on the network.
A few thoughts:
You have tested the ports on the AirPort Extreme and they are working, so the next step would be to disconnect the Ethernet cable that runs from the AirPort Extreme to the switch at the switch, and then connect a laptop to the Ethernet cable to check to make sure that you are getting a good IP address that way.
If you cannot, then you have a bad Ethernet cable between the AirPort Extreme and switch that will need to be replaced.
If the laptop is getting a good IP address when you run this "test", then you know that the AirPort Extreme and Ethernet cable are working correctly and the troubleshooting focus must now move to the switch.
Check to make sure that you have an unmanaged switch. Or, if it is managed design, that it has been configured to operate as an unmanaged switch.
Next, connect the Ethernet cable from the AirPort Extreme to the switch and disconnect all of the other Ethernet cables that are connected to the switch and test each port one by one with your laptop and a spare Ethernet cable to make sure that each port is working correctly.
If you cannot get a good IP address on your first test with the laptop connected to the switch, then you know that you have a misconfigured or defective switch.
If the switch checks out OK when you test each port, then the next step is to connect one of the Ethernet cables that runs to another area, and connect your laptop to the Ethernet cable to make sure that the cable is working correctly. Continue to test each Ethernet cable the same way.
About 95% of the time in issues like you are having, the problem is bad wiring somewhere on the network, even though the "tech" said that he tested everything. The trick is to find it....when there are no shortuts.

We cannot get our Ipad Air to charge. We have tried the wall plug and the computer plug in. It just gives us a message saying it's not charging.

We cannot get our iPad Air to charge. We have tried the wall plug and the computer plug in. It just gives a message saying it's not charging.

Could be the charger, cable or iPad. Plug the USB cable into your computer. It may say "Not Charging", however, it is charging slowly and will verify that the cable is good.
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
http://support.apple.com/kb/TS2802
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
iOS 7 Battery Life Draining Too Fast? It’s Easy to Fix
http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
iPad: Charging the battery
http://support.apple.com/kb/HT4060
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

HT201270 I connected the ipad to itunes...and the iphone...phone is OK..ipad isn't..I get a message saying I don't have a Data Plan..but when I try to rectify that..the message says I'm not connected to the server..help.

I connected my ipad and iphone to itunes this morning and downloaded updates...the iphone is fine..but my ipad is giving me the message...you have not signed up for a data plan..but, when it asks me to sign up..the message says Safari can't open the page because it isn't connected to the server...Mail isn't working either...help.

Try this:
1. Turn off iPad. Press and hold the Sleep/Wake button for a few seconds until the red slider appears, slide to turn off.
2. Connect USB cable to computer
3. Press and hold the Home button down and connect the docking end of cable to iPad
4. Continue holding the Home button until you see the "Connect To iTune" screen
5. Release the Home button
6. Open iTune (make sure you have the newest version of iTune)
7. You should see "iTunes has detected an iPad in recovery mode"
8. Use iTune to restore iPad
Note: You need to be patient and repeat the above many times to recover your iPad

Airport Extreme just stopped working

I have a airport extreme and and Airport Express. They have both been working on the same router for about a year or two. Now all of a sudden the Airport Extreme line doesnt work. I try to reconfigure and get the following message"Airport Utlity unable to find Airport wireless device after restarting." and goes on to say You may need to select your network from the WIFI menu and try again. Don't understand what this means? I have tried reseting the extreme hard and soft still will not find the airport connection or even the ethernet connection. Can these Extremes burn out ? Thank you for the help

It's not the power adapter. If it were, you would have no power at all going to the AirPort Extreme and you indicate that the port lights are functioning.
Power down the AirPort Extreme for 5-10 minutes and then restart the device. If you still see the same symptoms, I'm afraid that there has been an internal electrical component failure in the AirPort Extreme and it will need to be serviced or replaced.

Airport express just stopped extending the network

I have an airport express that I have been using for 3 years to extend the network in my house.
All of a sudden it started flashing amber. I've tried soft resets, hard resets, factory resets, and I can't get it to extend the network anymore.
I have 3 other expresses in the house that still extend the network, but this one won't.
Everytime I go run airport utility, it sees the express, and will actually allow me to JOIN the network (I get a solid green light, everything is good) but everytime I ask it to EXTEND the network, it gives me an error message and says it can't do it.
It's an old extreme, that I bought refurbished, so I might be able to accept it's old and needs to be replaced, but then why can I join the network, but not EXTEND the network?
Any thoughts would be appreciated.

Apple's instructions to "extend a wireless network" are on the main forum page and also here:
http://support.apple.com/kb/HT4259
Although the example pictures an AirPort Extreme as the "extending" device, the setup for an AirPort Express would be exactly the same.

Wireless Printing with Airport Extreme just stopped

Strangely, it is not working on one of my 3 computers only! Was working with all 3, today it would not print from my iMac with Intel 2.33 GHz.
No problem recognizing the printer. When I print the printer comes on, the printer head moves normally but a blank page comes out.
I have tried all the suggestions from Apple under the heading "Top Searches", subheading "Aiport Extreme/Express wireless printing" and I have also repaired disk permissions but nothing has changed.
Why would wireless printing work in an older computer and not a newer one? I have all the latest updates in BOTH the iMac and my Power Book so I can't blame a Security Update etc.
What now?
iMac Intel 2.33 GHz Mac OS X (10.4.10) Power Book G4, HP PSC 2410 All-in-one
iMac Intel 2.33 GHz Mac OS X (10.4.10) Power Book G4, HP PSC 2410 All-in-one

The exact problem for me. I also have checked all me settings, they seem to be
the way they should, but I can not get to print whatever.
I hope someone tell us what to do to make the printer work in an Airport
Extreme connection
PowerBook G4 Mac OS X (10.4.6) Airport Extreme Base Station and 2 Airport Express

Airport Extreme won't show the WD external hard drive I plugged into the USB port. How do I connect my external hard drive to my network?

I plugged in my WD external hard drive into my Airport Extreme via the USB port. The hard drive will not show up in the disk section in the airport utility... How do I hook an external hard drive up to the airport extreme? I have tried 2 different WD hard drives. I must be missing something!!!
Thanks!

To be recognized by the AirPort for sharing, the WD HDD has to be formatted in either HFS+ (ideal) or FAT32. The easiest way to format the HDD is to use the Disk Utility in OS X.

When trying to restore or even contact Itunes store my computer states the the ipod software server could not to contacted but I have checked netting work setting and everthing looks correct any ideas I can try as I am not a whizz on the computer yet

When trying to restore or even contact itunes store my computer states the ipod softdate server could not be contacted. When I checked the setting everything look correct. I have just changed from using xp on my computer and now using windows 7 so I am a bit lost with the different layout

maybe:
iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server

My Airport Extreme just stopped working. The message says ethernet cable not plugged in, but it is. Cable modem works fine. Is this a common problem?

Similar Messages

Maybe you are looking for