My ATV 2G with latest firmware doesn't stream audio to Airplay Speakers

Hi everybody,
I have an AppleTV 2G upgraded to the latest firmware (5.1.1 / ios 6.0.1).
My problem is that it doesn't stream audio to my airplay speakers. I have the B&O Beoplay A8.
The speakers work fine with my ipad and iphone, but not the ATV.
I checked the aiplay settings, the speakers appear there normally and I have ticked them and they are the selection for the audio output.
Instead AppleTV audio is on the TV.
Can someone please help me.
I got the speakers just for this reason. To listen audio from movies on ATV from the speakers.
Every help is appreciated.

Timing-wise the problem coincided with upgrading the firmware on my Airport Express to 7.6.4 (reverting to the previous version doesn't seem possible).
Reverting to an earlier firmware version is possible with v5.6 of the AirPort Utility. Note: This version runs fine under OS X Mountain Lion but will not install without a workaround. Let me know if you need it.

Similar Messages

  • The bottom part of my iphone4 screen cannot tap.. restored 2 times with latest firmware and yet still the same..is it possible to fix this?how?

    The bottom part of my iphone4 screen cannot tap.. I restored it 2 times with the latest firmware and yet still the same..is it possible to fix this?how? please guys help me =(

    iPhone and iPod Touch: Troubleshooting touchscreen response: http://support.apple.com/kb/TS1827

  • Access Restrictions still not working with latest firmware

    Linksys WRT54GS V5 with firmware v1.52.2
    I cannot believe what a frustrating experience this is. All I want to do is block facebook.com from my two high schoolers until they’ve done their homework.
    Starting out, it simply did NOT work, and I discovered from this forum that the initial firmware did not work for this feature. So here is what I did:
    - Downloaded v1.52.2 firmware, which is indicated as being the latest for this router
    - Upgraded the router, per the instructions with this firmware.
    - Pressed (and held)the reset button for the indicated 30 seconds
    At this point, my router switched back to the default access point name and access password. Fortunately, I had backed up my configuration, so I then:
    - Loaded my previous configuration that included my Wireless security settings, different AP name, etc...
    - Powered down, then back up router, cable modem.
    Router now works wireless as before, but Access Restrictions still does not restrict. Router does list the correct firmware on the admin screens.
    Here is how I sent up my one (and only policy)
    Internet Access Policy: 1(facebook)
    Status: Enable
    Enter policy name: facebook
    PCs: Allow checked
    Days: Everyday checked
    Times: 24 hours checked
    Blocked Services: NONE
    Wewbsite Blocking by URL Addresses:
    3 entered, they are:
    http://www.facebook.com
    http://static.ak.facebook.com
    http://apps.facebook.com
    Website blocking by keyword: All 6 boxes empty
    This was easier to do on my old netgear router, and it also actually WORKED. ARGHHHHHH

    Thanks, but that did not work either. It seems to me that, entering mac addresses ended up totally taking away all internet access for the computers on the MAC list. This is really pathetic that a concept that on the surface seems so simple, as in 'deny access to hostname xxx.com' can be so difficult to implement. If there wasn't the suggestion that this were a feature of the router, I wouldn't care. But it *is* supposedly a feature, and the feature simply does not work.
    It seem to me that LinkSys has too many mutually exclusive options on a single page. It would be easier to grok if the hostname filter had it's own page, then you wouldn't be wondering what the 'deny/allow' check box did or did not do in conjunction with your selections.
    Does the feature work or not? As I mentioned, this was childishly easy to accomplish on my Netgear router. If it didn't suck so bad in other areas of performance, I'd simply go back to it.

  • Mail for Exchange Error with Latest Firmware for N...

    I downloaded the latest firmware for E 90 (version number begins with 300. ....). I installed the latest version of Mail for Exchange and as soon as it connects, it immediately disconnects the mail sync.
    MFE was working fine with my old version. Can you advise, what could be the problem Also can i downgrade my version to the old version.
    Cheers
    Rohit

    It could be a servicepack issue. Read this:
    http://europe.nokia.com/find-products/nokia-for-business/software/email-and-instant-messaging/mail-f...
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • IPHONE PROBLEM WITH LATEST FIRMWARE

    I just updated my iphone to the latest firmware and i now i cant synch my iphone with my computer.. every time i do it, it shuts my computer down.
    i'm running window vista
    any suggestion or help

    Oh, that's great news. Well, I'm not messing with my USB Periphs...they are/were all working fine, so I'm going to wait for Apple to come up with a fix for this problem.
    I'm now on my 3rd uninstall/reinstall of the Mobile Support and iTunes.
    After this, that's it. I'll have to wait until someone finds an easier fix. For all of you who got 2.1, enjoy. My phone crashes about 3 times a day and I'd really like it, too.

  • Ovi Suite 2.0 + N97 with latest firmware.... Devic...

    Just got phone, installed software cd, when prompted to update software from internet i did and then once it was all installed connected phone no problem, did a firmware update like it asked and now the Ovi Suite no longer recognises the phone, but the Ovi Player and my computer recognise it perfectly fine.
    Using Windows XP Pro
    Nokia n97 32gb
    Nokia Ovi Suite 2.0.1.35
    PC Connectivity Solution 9.39.0.0
    Connectivity Cable Driver 7.1.20.0
    Maps Service API 3.0.35.0
    Nokia mPlatform 2.5.197
    Ovi Desktop Sync Engine 1.0.0.684
    Operating system:
    Microsoft Windows XP 32-bit Edition, Service Pack 3
    Language: English
    And the firmware is 
    Solved!
    Go to Solution.

    Hi virusviper,
    My suggestion to you would be, In control panel, Add or remove programs, select Nokia OVI Suite and then Change/Remove option, you will be get Repair and Uninstall.  I would suggest you to repair Nokia OVI Suite and check, if it has resolved your issue, if not, Uninstall Nokia OVI Suite, PC COnnectivity Solution, Nokia Connectivity cable driver, Nokia flashing connectivity cable driver(if any got installed on your PC), Run reliable PC Cleaner, install Nokia OVI Suite from www.nokia.com/ovisuite, Reboot your pc and check

  • My linksys wrt54g v6 with latest firmware cant get internet

    anybody know what the problem is im connected to a compaq presario notebook wired thx to anybody who can solve this problem.
    (Mod note: Edited post for guideline compliance.Thanks!)Message Edited by JOHNDOE_06 on 12-31-2006 12:35 PM

    Hi…Go to www.linksys.com/connect and download the easy link connect, automatic configuration tool and run the tool and follow the instructions on screen and if will configure your router automatically.

  • Reproducible bug in iPod Classic latest firmware, crash after Contacts

    Reproducible bug:
    You can't enter the contacts item on the iPod Classic 120gb with latest firmware (possibly affects newer iPods too), when you haven't synced any contacts..
    However, if you put the contacts in the main menu (Settings -> Main Menu, then check 'Contacts'), you CAN enter it.. When exiting the Contacts menu (which says you have to sync contacts through itunes first) with the Menu button on the iPod, it instantly resets..
    Reproduced a number of times..
    Message was edited by: Stijn Spijker

    I'd suggest that you report this to apple by calling them or leaving them feedback at:
    http://www.apple.com/feedback/ipod.html
    As if it is a firmware issue there's nothing that can be done until they release an updated edition.

  • Latest Firmware SG-300-28

    hi,
    we have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, can any one help me out for latest firmware is used for the same ?

    Hi Amit,
    Thank you for posting. The latest firmware for the SG300 is version 1.1.2.0
    You can download it at the following page currently:
    http://www.cisco.com/cisco/software/release.html?mdfid=283019617&catid=268438038&softwareid=282463181&release=1.1.2.0&relind=AVAILABLE&rellifecycle=&reltype=latest

  • After EFI firmware update the scrolling with two fingers doesn't work inside the browsers (both safari and chrome)

    I've got a new MacBook Pro Retina from october 2013 13" (8 gb Ram and 256 gb SSD).
    I had the "freezing" issue that was solved with the firmware EDI update.
    But after this update i have now another problem: often during web browsing the scroll with 2 fingers up and down the page stops working (but the trackpad is ok for everything else and if i go in other programs the scroll works as usual). The only solution is to restart the browser but the problem happens again and again.
    Both on Chrome and Safari. Especially on Safari everything freeze if i try to scroll on the right to go back to the previous page.
    Does anybody else have this issue?

    macmattia wrote:
    I've got a new MacBook Pro Retina from october 2013
    Does anybody else have this issue?
    Doesn't matter if anybody else has this issue. 
    You are still under warranty.  Call Apple Care. Make sure you get a case number as all repairs have an additional 90 days of warranty. 
    #1 - You have 14 days from the date of purchase to return your computer with no questions asked.
    #2 - You have 90 days of FREE phone tech support.
    #3 - You have the standard one year Apple warranty.
    #4 - If you've purchased an AppleCare Protection Plan, your warranty last for 3 years.   You can obtain AppleCare anytime up to the first year of the purchase of your computer.
    Take FULL advantage of your warranty.  Posting on a message board should be done as a last resort and if you are out of warranty or Apple Care has expired.

  • Im using an iphone 4s with the latest firmware which is 6.1.3 but my wifi button keeps going grey how can i fix it? i rested network connections and it worked for a while and went grey again,what can i do?

    im using an iphone 4s with the latest firmware which is 6.1.3 but my wifi button keeps going grey how can i fix it? i rested network connections and it worked for a while and went grey again,what can i do?

    Have you worked through the Troubleshooting iOS and WiFi knowledge base article?  If not, see if there is info in there that might help.
    Is the WiFi greyed out on all WiFi networks or just the one?  If it does this on all then there may be a hardwaer problem that needs attention from the techs at an Apple store genius bar.
    Before that, however, try a reboot by holding both the power and home buttons until the apple logo appears and it restarts, ignoring the red slider if it appears.  That clears a lot of iOS hang ups that occur.

  • SPA525G2 latest firmware to work with UC320W (v7.5.7 ok to use?)

    Hi all
    I have had some minor issues with the SPA500S and the SPA525G2 when using it with the UC320W, currently all the phones (SPA525G2) i think are hardware v2 or v2.1.1 with firmware 7.5.2(u2),
    I understand to get the latest firmware v7.5.7 on to the phone i would need to factory reset it, get it on the LAN and upgrade it, then plug it back on to the VLAN and get the UC320 to find the phone again.  Does the above sound correct (and the only way to do this)?
    Is v7.5.7 stable on the UC320w PBX?
    Many Thanks
    Ashley

    Hi
    I am aware the UC series from Cisco is EOL, however we are looking for a closed system which seems to be hard to find thats as good as the US320w.
    Items like 1 button Parking Orbits that work, seem impossible to find in another system.
    For documentation, we have looked at so far:
    Zultys which do a hardware server (MX ME) , they also do phones and attendant consoles (there made by Aastra i think, branded Zultys), however there top line color touch screen phone (ZIP 59i), when we saw it in use for parking orbits was abysmal, 1-2 presses to park then you have to remember the parking slot number to get it back, also appeared bad use of the touch screen system, the SPA525G2 isn't touch screen but functionally with the US320w is a better system.
    Avaya has an IP Office v2 hardware which you buy plug in hardware boards, however this appears to only work with the more basic Avaya phones, although there system inside the IP Office appears really advanced showing the phone image with what button does what, even has plug and play so just plugging the phone is, it works with an extension number.
    However there better phone (IP9670G) does not appear to be compatible with there IP Office, we are currently still investigating this.
    We like the closed systems, they work better and easier to maintain, i understand changing brand means replacing all the phones which at this point wont be a major issue.
    I would prefer to stick with the phone manufacture as integration and provisioning is alot easier.  We are very happy with the UC320w, however it is EOL and we would like to get better integration and video conferencing as well so am looking at whats around.
    Any input here would be good as to other IP PBX hardware.

  • Problems with the latest firmware upgrade

    I found a problem with the 01-10-2006 firmware upgrade. Now that it is inside my ipod certain videos don't play properly anymore. Actually the video starts, it plays normally for a while and then it goes still for a few seconds and then, when it plays again, the audio is gone.
    It always happens in the same point with the same video. In particular, just in case someone wants to try, it happens in the latest nasa video podcast.
    I don't know what to do!
    I'll try to step back to the 1.0 version...

    I'm having this problem as well. Sinse I updated the firmware all of my movies get stuck about every 10 seconds then if I wait a few seconds they start up again but with no audio. I'm quite certain that this is a problem with the firmware sinse the videos play fine on quicktime, they used to play fine in my ipod before I updated it, and I can get it to play the parts it gets stuck at if I rewind it but it happens very frequently and each time takes a while to reload. If anyone has found a way to solve this problem please let us know.

  • Doesn't recognize my movies with new firmware

    With the new firmware, I can't go to My Movies, where I have a few movies bought from Apple. I get a blank screen and I have to reboot Atv. All the rest works fine (music, tvshows, rent, etc). I guess there is a problem with that firmware and hope it will be solved soon.

    is your appletv modified in any way ?

  • When I try to update my iphone with latest software, it says it can't because the firmware file is not compatible. Any help??

    what is firmware file? It says it is not compatible when I try to update iphone with latest software

    I've used the more like this.... they are all full of non answers and shots rather than being helpful unfortunately... does anyone have a real approach to resolving this issues for the dozens looking through the multiple threads for a a helpful response?  If so guidance would be greatefully appreciated.

Maybe you are looking for