My AX is HOT!!!

I just got a RFB AX, the setup is smooth. It is ready to use in 5 mins which is awesome!!!
The only thing I worry about is the temperature of my AX.
The device is Hot, even though it is not burning hot, but it wouldn't be pleasant to hold with your hand.
Is it normal?
Any settings I could change to make it cooler?
many thx

Hi, keiman. Welcome to the forums!
The Express doesn't have a fan, so it uses its case to dissipate heat. For that reason, it's normal for it to get kind of hot.
I wouldn't worry about it. Just be sure there's air around it so that the heat can dissipate.

Similar Messages

FIX FOR: iPhone 4 battery draining fast, phone running hot

I had the same issue many have reported here and in comments on blogs, where their +_battery was draining at least twice as fast_+ as on an iPhone 3GS with iOS 4.
Some threads suggest +_this happens to iPhone 4 when restored from a 3G or 3GS_+, and indeed, that's what I'd done. A few people said that resetting to factory settings and installing everything fresh solved the issue, giving them better battery life than they'd seen on any prior iPhone.
Many of my apps have files or settings stored in them, so I didn't want to have to set everything up again. A fresh install is a real pain.
Deep in an iPhone 3G thread mentioning a similar battery problem after upgrading to iOS 4, someone said they'd deleted all their mail accounts, and set those up fresh, which solved the issue for them. I tried that today, and it worked.
*_BEFORE AND AFTER_*:
Thursday and Friday, the iPhone 4 went from 100% to 15% in under 6 hours. Today, after this fix, the iPhone 4 is at 87% after 12 hours. Thursday and Friday the phone was hot to the touch whenever I picked it up. Today it's always cool. Apps usage and movement among coverage areas on each day have been exactly the same. The only change was resetting up mail.
*_STEPS TO FIX_*:
Do this on WiFi so you can sync and check mail fast.
1. Delete all mail accounts.
2. If MobileMe user, delete MobileMe account, and remove all Calendars, Contacts, Notes, etc., from the phone (so you don't have dupes when you re-sync).
3. Turn off phone, and back on again.
4. If MobileMe user, add MobileMe account first. I enabled all options, even Find My iPhone (Thursday and Friday I had it off, in case it was using power). Wait long enough for contacts and calendars to sync, check to make sure. I use MobileMe mail on Push.
5. Add back each additional mail account. I have 5. I am in a marginal coverage area, so I set these accounts on Fetch Hourly. I also have "Preview 5 Lines" (I think the default is Preview 2 Lines. This doesn't matter.)
6. Go into Mail, go to the MobileMe Inbox, and scroll your way down letting the messages come in. You can see them come in when you see the Preview Lines update, and then scroll some more.
7. Go into each additional mail account's Inbox, scroll your way down, letting the messages come in.
8. Go to the combined Inbox if you use that, make sure all the messages are in.
9. The WiFi activity spinner may remain spinning even after Mail says it is done Checking Mail. This is because other parts of mail accounts are being synced for the first time. Let the iPhone sit in Mail combined inbox until the spinner stops. Quit Mail, go back in, and watch the spinner after it's done Checking Mail. If the spinner doesn't stop after < 5 seconds or so, let Mail sit again. Once it's caught up, going into mail will Check Mail, and the spinner will stop a few seconds after as it should.
10. You're done.
Hopefully your phone stays cool and your battery life reflects the boost from the 20% larger battery. If not, the next step to try is Reset Network Settings, and finally try a factory reset and installing everything fresh instead of doing a restore. Hopefully you won't need to do that. I didn't.

My iphone 4 just started to warm up and the battery is draining quick. Closed everything and reset to no avail. Turned off bluetooth, increased push time and checked location settings for new applications. Weather Doodle was a bit suspicious as it had a purple direction indicator next to the setting. The only other new app I installed was Lego instruct. I disabled one of the 4 mail accounts I had that is having network difficulties, went to airplane mode and still I see %1 drain every 10 or 15 minutes. I'll remove the new new apps and reset to see if it is related to the new apps. If that doesn't work, I'll try email account reset at home wifi and see if that fixes the issues.
Thank you for the information.
version 4.2.8
Verizon

Hot mail wont open emails

can get up hot mail but refuses to open email....sometimes says "MSN server" not found" and freezes

it was a "bundle" problem.. got it solved! thanks

How Can you get your hot mail.

How can I use mail on my Mac to get my hot mail like i did with outlook on my PC.?
Mac Minni Mac OS X (10.4.7)

Hello,
If you want to use MSN / Hotmail with Apple's mail, check out the program HTTPMail Plugin at:
http://www.automagic-software.com/downloads.php
You can also download it from SourceForge:
http://sourceforge.net/projects/httpmail-plugin
And, strangely, while both the developer's site and SourceForge lists the latest version as 1.47 - Tiger release 2005-11-25, I found a 1.48 release at:
http://mac.softpedia.com/get/Internet-Utilities/httpmail-plugin.shtml
And also:
http://www.macupdate.com/info.php/id/10842
And also:
http://www.versiontracker.com/dyn/moreinfo/macosx/18189
I just downloaded the 1.48 version, and it is in-fact a 1.48 release. So, that would appear to be the most current version. Perhaps the normal / direct sites just haven't been updated yet.
You can see a screen-shot and brief description of the older 1.46 version at:
http://www.apple.com/downloads/macosx/email_chat/danielshttpmailplugin.html
The 1.47 version of the httpmail plug-in was released in November of 2005. But, the 1.48 version was apparently released in March of 2006.
It is not a "universal binary". It is a PowerPC only program / plug-in.
This is not an issue if you are using a PowerPC Mac. You can just install it and use it.
As for Intel Macs, it will install, but not run in a Intel Native program.
If you want to use a PowerPC plug-in with Mail on an Intel Mac, then you have to set Mail to run in PowerPC mode through Rosetta.
That will enable the plug-in to work. But, that means running mail through Rosetta which may be slower.
Just to be safe, you might actually want to set mail to run in Rosetta before you install the plug-in. That would probably be the safest route.
Here's a document about forcing a program to run in Rosetta.
http://docs.info.apple.com/article.html?artnum=303120
Give this a try and see if it works for you.
Hope this helps.

My iPod is fixed on streaming. It reset and go back to streaming. Battery is extremely hot

My iPod Touch is hanging. I tried to reset it, but as soon as it finished starting up it goes back to streaming. The battery is very hot and there is no option for me to turn it off.
Any information would be appreciated

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
I do not know what you mean by back to streaming.

Trying to create a text that is on fire or more like a hot branding iron

Trying to create a text that is on fire or more like a hot branding iron

Something like this?
That was from a project I did a few months ago. Sounds similar to what you want. I did that in After Effects.
Basically all I did was add a glow effect to the text and messed around with the glow parameters. The black smoke is animated and moves on the actual video and is basically some pre keyed smoke footage that I had. The smoke was originally gray but black looked cooler.
I'd say it's pretty close to your hot branding iron thing.

Unable to capture in Async Hot Log

Hi,
I am unable to get the changes captured in async hot log mode of operation. Have verified that DB is in archivelog mode and am able to create change tables, but changes in the source table are not getting propagated. Is it due to logs not getting picked up from the proper place.
my change_sources view has empty values in all the fields except source_type, source_description and created.
would appreciate any pointers for what may be missing..or how to go about identifying the problem.
Thanks,
RK

Thank you Patrick. You have helped me before, so thanks again.
I do not have anything else connected to the firewire ports. I have an external hard drive, but I have tried to capture with and without the hard drive attached. I did recently back up using Carbon Copy Cloner to another hard drive, if anyone thinks this may be the issue.
I can't recall the exact error message in FCP (I have deleted the program trying to fix the issue, and focus on the capture problem in Quicktime thinking that if Quicktime and iMovie both don't capture, that the problem is not with FCP, but either with the OS or the back end of QT) I can re-install FCP to give you the exact FCP error message if you would like me too. Ie, if the exact error message is necessary.
Thanks again for your response.

How can I use my iPhone'hot spot to send email from my computer ?

Hi,
My land line is dead ... so no phone nor internet at home. But I can use my iPhone'hot spot to get on the web from my iMac. Great ... it works !
Oups ! I cannot send email from my computer using my iPhone's hot spot with Mail.
How do I do that ?
Regards.
Robert Lespérance

Hi iCare,
Thanks for helping ... All that configuration is already done. I am able to surf the web from my computer using my iPhone's hotspot.
When I want to send an email from my computer, I get a message asking me to select the the SMTP server. Then I select my usual ISP server, but the message comes back telling me it does not work.
Is there any other configuration to do ?

How do I use my iPhone's hot spot to send email with Mail ?

Hi,
My land line is dead ... so no phone nor internet at home. But I can use my iPhone'hot spot to get on the web from my iMac. Great ... it works !
Oups ! I cannot send email from my computer using my iPhone's hot spot with Mail.
How do I do that ?
Regards.
Robert Lespérance

Hi Templeton Peck,
Thanks for droping in my thread ...
Doesn't the fact that I can surf the web with my iPhone's hot spot and that I cannot use Mail normally has I normally do give you a clue what the problem could be ?
What other information can I give you other than normally I can surf and send email with my regular ISP. Now that my ISP is dead I am using my iPhone's hotspot to surf the web awaiting that my ISP's connoection returns. Surfing is OK but I cannot send emails with through Mail.
When I want to send an email from my computer, I get a message asking me to select the the SMTP server. Then I select my usual ISP server, but the message comes back telling me it does not work.
Is there any other configuration to do ?

MBP won't wake, is REALLY HOT, fans going full blast

This morning I made sure when I closed the lid on my MacBook Pro, that it went to sleep (pulsing sleep light). I found that this doesn't always happen right away, unlike the old Powerbooks. I then put it into my laptop bag, confident that it was fully hibernating.
When I arrived at work and pulled the MBP out of the bag, the sleep light was solid white, the laptop was really hot on all sides, and the fans were running hard. I opened the lid and there was no display, although I knew it wasn't sleeping because I could hit "caps lock" and it would toggle on/off. Apparently it had awaked while in my bag for some reason. The only way I could regain control was to hold down the power button and start from a "cold" boot. When I logged back in I could not find anything odd in /var/log/system.log during the time before the reboot.
My Energy Saver settings for "battery" mode are set to "Better Battery Life" so theoretically nothing should be able to externally wake the MBP. Bluetooth is Off. I have no idea then what caused it to wake up and flip out. This is the second time this has happened and I've been wary of its sleep behavior. Is there an updated SMC firmware for the 17" model yet?
This is really worrying because I could have left it in my bag for a lot longer and who knows, maybe it would have caught fire!

It happened again. I did a hard shutdown to keep it from really geting hot. After the boot, I checked the system.log. At the time which I suspect the interrupted sleep occured I saw this, which seemed to repeat a few times:
May 24 15:51:49 DragonStalker kernel[0]: System SafeSleep
May 24 15:51:49 DragonStalker kernel[0]: hibernatepage_listsetall start
May 24 15:51:49 DragonStalker kernel[0]: hibernatepage_listsetall time: 157 ms
May 24 15:51:49 DragonStalker kernel[0]: pages 317726, wire 41405, act 17645, inact 56798, zf 23232, could discard act 40087 inact 138559
May 24 15:51:49 DragonStalker kernel[0]: hibernatepage_listsetall found pageCount 317726
May 24 15:51:49 DragonStalker kernel[0]: IOHibernatePollerOpen, mlget_interruptsenabled 0
May 24 15:51:49 DragonStalker kernel[0]: IOHibernatePollerOpen(0)
May 24 15:51:49 DragonStalker kernel[0]: writing 317506 pages
May 24 15:51:49 DragonStalker kernel[0]: image1Size 62995968
May 24 15:51:49 DragonStalker kernel[0]: all time: 7180 ms, comp time: 1223 ms, deco time: 0 ms,
May 24 15:51:49 DragonStalker kernel[0]: image 251436544, uncompressed 568770560 (138860), compressed 250429744 (44%), sum1 b7819032, sum2 3170f161
May 24 15:51:49 DragonStalker kernel[0]: hibernatewriteimage done(0)
May 24 15:51:49 DragonStalker kernel[0]: sleep
May 24 15:51:49 DragonStalker kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
May 24 15:51:49 DragonStalker kernel[0]: Started CPU 01
May 24 15:51:49 DragonStalker kernel[0]: IOBluetoothHCIController::restartShutdownWL this is a wake from sleep
May 24 15:51:49 DragonStalker kernel[0]: System Wake
May 24 15:51:52 DragonStalker kernel[0]: hibernate image path: /var/vm/sleepimage
May 24 15:51:52 DragonStalker kernel[0]: sizeof(IOHibernateImageHeader) == 512
May 24 15:51:52 DragonStalker kernel[0]: Opened file /var/vm/sleepimage, size 2147483648, partition base 0xc805000, maxio 400000
May 24 15:51:52 DragonStalker kernel[0]: hibernate image major 14, minor 2, blocksize 512, pollers 3
May 24 15:51:52 DragonStalker kernel[0]: hibernateallocpages flags 00000000, gobbling 0 pages
May 24 15:52:53 DragonStalker kernel[0]: System SafeSleep
May 24 15:52:53 DragonStalker kernel[0]: hibernatepage_listsetall start
May 24 15:52:53 DragonStalker kernel[0]: hibernatepage_listsetall time: 213 ms
May 24 15:52:53 DragonStalker kernel[0]: pages 318013, wire 41442, act 17793, inact 56833, zf 23297, could discard act 40087 inact 138561
May 24 15:52:53 DragonStalker kernel[0]: hibernatepage_listsetall found pageCount 318013
May 24 15:52:53 DragonStalker kernel[0]: IOHibernatePollerOpen, mlget_interruptsenabled 0
May 24 15:52:53 DragonStalker kernel[0]: IOHibernatePollerOpen(0)
May 24 15:52:53 DragonStalker kernel[0]: writing 317779 pages
May 24 15:52:53 DragonStalker kernel[0]: image1Size 63012864
May 24 15:52:53 DragonStalker kernel[0]: all time: 6870 ms, comp time: 1770 ms, deco time: 0 ms,
May 24 15:52:53 DragonStalker kernel[0]: image 251865600, uncompressed 569880576 (139131), compressed 250799380 (44%), sum1 d4c3f6a7, sum2 7a9619a0
May 24 15:52:53 DragonStalker kernel[0]: hibernatewriteimage done(0)
May 24 15:52:53 DragonStalker kernel[0]: sleep
May 24 15:52:53 DragonStalker kernel[0]: Enabling XMM register save/restore and SSE/SSE2 opcodes
May 24 15:52:53 DragonStalker kernel[0]: Started CPU 01
May 24 15:52:53 DragonStalker kernel[0]: IOBluetoothHCIController::restartShutdownWL this is a wake from sleep
May 24 15:52:53 DragonStalker kernel[0]: System Wake
There is some indication that Bluetooth is involved (I could be wrong) but I know my Bluetooth is Off (icon is dimmed) and it is set to NOT wake the computer.

My touch pad getting hot and freezing up while my laptop just on.

When I use my notebook more than 2-3 hours while on floor or hard surface touch pad gets hot or does not work properly I have new 5months used notebook and latest touchpad drivers. But when I use my notebook as playing games or watching movies with external mouse then my touchpad getting too hot but notebook remains normal condition.
This question was solved.
View Solution.

According to the message you have recently posted I would like to confirm that this could be a hardware issue and I strongly recommend you to immediately Contact HP Technical Support over the Phone for further assistance without any delay to get your Notebook diagnosed and serviced by an authorized HP Certified Engineer
You can also Check your warranty Here to verify the warranty status
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
GBL84
Although I am an HP employee, I am speaking for myself and not for HP

Hot Synch Error - Tungsten E2 Docs to Go Application

HotSync operation started for Joyce on 11/10/08 22:09:05
Expense - sync configured to Do Nothing
OK Quick Install
Outlook Notes
- Do Nothing
OK Outlook Notes
OK Media
Documents To Go Message(s)
Error accessing Documents To Go user information.
You must first open the Documents To Go desktop application, select the appropriate handheld user, and synchronize again.
Post relates to: Tungsten E2
Post relates to: Tungsten E2

ComputerWiz wrote:
Hello,
Thanks for pasting your hot sync log - it makes it easier to help you out now.
Open the Palm Desktop program. Click on Start > Programs/All Programs > Palm One > Palm Desktop.
Locate the Documents/Documents To Go icon on the left side and click on it. You will be prompted to go through some initial setup steps to set up the Docs To Go. After you go through those steps, close the Palm Desktop program and try to sync again.
Now it should work without any errors.
Post relates to: None
Locate the Documents/Documents To Go icon on the left side. There is no Documents to Go in palmdesktop application. But is is working on Tungsten E2. I'm unable to backup or hotsynch this application. Error on desktop log:
Documents To Go Message(s)
Error accessing Documents To Go user information.
You must first open the Documents To Go desktop application, select the appropriate handheld user, and synchronize again.
I have explained this error to cygnusX1 and this person said contact dataviz.com b/c it's their software that came with the handheldand this forum doesn't fix applications from 3rd party.
Post relates to: Tungsten E2
Post relates to: Tungsten E2

Hot Synch with Windows XP and MS Office 2007

I can not synchronize my Palm Treo 680 Unlocked with Windows XP Home and MS Office 2007.
I see several comments regarding Outlook 2007. Is resolving the synchronization of Outlook 2007 the same solution as Office 2007?
If so what is the solution?
Post relates to: Treo 680 (Unlocked GSM)

I also cannot synch my Palm Treo 680 unlocked with Outlook 07 using Vista. It says "Hot Synch Operation Completed Successfully", but nothing did synch. I downloaded palmoutlook07conduits.zip and there was no change. I was synching wirelessly using Microsoft Exchange Active Synch without problems, but when I cancelled my 'data' package on my cell phone, it no longer was synching. I tried reloading my original Palm CD, but it doesn't allow me to select 'Outlook' as my connectivity. Please help. And please don't provide me with a bunch of acronyms as I won't understand them!!!!
Thanks,
Post relates to: Treo 680 (Unlocked GSM)

Hot synch Palm Vx

I have a Palm Vx on a Windows XPpro system. It was working fine and hot synching fine until about 2 months ago when a virus came in and I had tech guy reformatt the hd. He loaded desktop 6.2. I don't remember what version i had before it was reformatted. It might have been 6.2
Now, the Palm says it is synching ok but when I open up desktop 6.2 I don't see any of my memos or phone information that I used to see.
I cannot tell if the desktop 6.2 is looking at the file flocation where the synch says it is putting the files.
I CANNOT lose what is on my Vx. I've told my kids that when I die, forget about me but find my Palm! I still love it!!
Is the desktop 6.2 compatible with a Vx? should I try to go back to 4.1.4? I cannot find my original installation CD.
Help!
Post relates to: Palm Vx

I suggest you revert to Palm Desktop 4.1.4.
In the alternative, there is a utility available from pimlicosoftware.com called PalmHotsyncSetup which makes Palm Desktop 6.2 compatible with older Palm devices. But PD 6.2 was released for Windows Vista and later computers, and there is no reason for you to be using it.
Good luck!
smkranz
I am a volunteer, and not an HP employee.
Palm OS ∙ webOS ∙ Android

Hot Synch

I am using my tungsten E 2, few days back after hot synchronization I lost my contact & tasks, please help me & let me know the procedure to restore the same
Sanjay jain
Post relates to: Tungsten E2
This question was solved.
View Solution.

Is you data gone from the Palm Desktop and the device? Did you Hotsync more then once? See this procedure to recover data if you have not synced more the once with your Palm DT.
You can recover the data from your user folder provided you have only sync'ed once with the PC when you discovered the data missing. When you sync to the PC there are files created for each PIM category in your user folder. For Example; datebook.dat or datebook (Depending on the version of Palm Desktop) and datebook.bak. Using 6.2 the file names are .mdb and mdb.bak. For 6.2, the files are located in the username folder in PalmOSdesktop in my documents.
The files are named .dat and .bak. When you sync, the current data is stored in .dat. The next time you sync the data in the .dat file is copied to the .bak file. You can rename the .dat to .old. then rename the .bak to .dat. If the data in the .bak file is intact, it will now be in palm desktop when you reopen Palm desktop. I have included a link to show you how to find the userfolder on the PC.
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=26674
Here is another link regarding data loss;
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=39503
The best way to backup your data is to use the export feature in Palm Desktop. Make a new folder on the PC desktop named Palm Desktop Backup data. Next, select the category you want to export. You will get a window that asks where you want to save the file, save in the folder created on the desktop. There is a button that allows you to select currently selected record or all, select all. If you don't select all, then only the record highlighted is exported. You will then need to name the file for export, I suggest the name of the category, eg: datebook (With current date). Do this for all critical data in each category. With the data exported to the folder on the PC desktop, you can save this data to a flash drive, external hard drive or a CD-RW. With this method you will have your data in a seperate place than Palm desktop and the device. If you "Lose" data again, you can import the data back into palm desktop.
Make sure that when you make changes in palm desktop or the device to export the data to the folder created for the backup.
Here is a link for other options for backing up your data;
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=28751

Hot Synch Manager Settings (Conflict Resolution)

Hello,
I synch an office desktop and a home desktop with one Palm Z22. I have had a lot of problems with duplicate appointments ! How should I configure the Hot Sync Manager settings? I have the conduits (calendar, note pad, etc. ) set on "synchonize the files". But when I click on "change" and then "settings", I'm brought to the option of "Conflict Resolution" and the choices are duplicate, Outlook wins, Handheld wins, or ignore. Which should I choose if I want to avoid duplicate appointments ?
Thank you.
Nancy
Post relates to: Zire
This question was solved.
View Solution.

Yes, that's what I'd set it to. You want the information to flow in only one direction on the slave computer. Handheld --> computer.
WyreNut
Post relates to: Centro (AT&T)
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

My AX is HOT!!!

Similar Messages

Maybe you are looking for