My cable doesn't work after two months I bought my iphone 6. Whether could I get a new one from apple free charge?

my cable doesn't work after two months I bought my iphone 6. Whether could I get a new one from apple free charge?

It's covered under the same warranty as the phone. So long as it's not physically damaged, they should replace it for you.

Similar Messages

Why tethering with USB cable doesn't work after IOS6.0 update?

why tethering with USB cable doesn't work after IOS 6.0 update?

Try updating the carrier settings, if that doesn't do it try following along with this Apple doc -> iOS: Troubleshooting Personal Hotspot

Tablet stop working after two months

Dear Sir/Madam,
I am using a tablet Seriel Number: <Personal Content Removed> in Cambodia and did not work over two weeks (Can not turn on) after buying over 2months from Sanfrancisco, USA. I would like to send back your repair center, so could you tell me where should I send from Cambodia? you can contact me<Personal Content Removed>
Look forward to your reply soon.
Best regard,
Mao

Sunmao wrote:
I would like to send back your repair center, so could you tell me where should I send from Cambodia? you can contact me<Personal Content Removed>
Try what has been recommended above.
This is a user-to-user community support forum. We are not RIM employees, but volunteers who enjoy assisting other users. RIM personnel rarely comment on queries posted here.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Why my apple care for iphone doesn't transfer to my new phone after I claim a new one from apple store ?

2 days ago my iphone fall into a sink full of water. Yesterday I went to apple store and ask for apple care for iphone and they have it. So, I bought it and registered it right away since my iphone still be in a garentee and still not surpass one year usage. Then they told me that my iphone problem considered in a "physical damage case" which they have a policy for claiming a new iphone and pay some fee. After I got my new iphone, they said that all the information and phone data which is registered into apple system about the phone and the user and bla bla bla will transfer to my new iphone. Today, I just check my phone serial number in "support & coverage " column and I found that all the phone data in apple system is already transfered from the old one to the new one EXCEPT the data of apple care that I already registered before I claimed the new phone. Now, the question is " What can I do ? " and " will it be transferd to my new iphone or I have to buy a new apple care for my NEW PHONE That I got from their service "

Placing your iPhone in the toilet was the correct thing to do but you should have purchased an android phone instead. That would have solved these issues. :-)

My ipod touch is getting hot like starting 2 days ago and i had it for 2 months so then i got a new one from apple from my warranty but the new one is still getting hot and by the way i have a skull candy case

i really need help please im really worried i cant sleep nor play plz give me awnsers soon

- A case makes it harder for the iPOd to disipate the heat that occurs during operation of the iPod. During heavy use like gaming, the iPod can get quite warm.
- I would make an appointment at the Genius Bar of an Apple store since hot warm is hot is subjective. Make sure you bring the case.

Fit the window with mouse doesn't work after new update 10.9.2

Hi, I could fit a windows using my mouse wheel or two finger(on trackpad), doesn't work after I set up new Mavericks update(10.9.2) I'm using Haswell rMBP. Can anyone help me please? Thanks a lot. (Also, minimize with mouse wheel doesn't work too.)

Doesn't anyone having this issue?

IPhoto 8.1.2 doesn't work after reinstalled the OS 10.6.8?

iPhoto 8.1.2 doesn't work after reinstalled OS 10.6.8?

To re-install iPhoto
1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
2. Download it from the App Store to reinstall It's on your Purchases List* there.
For older versions that have been installed from Disk you'll need these additional steps:
2a: On 10.5: Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
2b: On 10.6: Those receipts may be found as follows: In the Finder use the Go menu and select Go To Folder. In the resulting window type
/var/db/receipts/
2c: on 10.7 or later they're at
/private/var/db/receipts
A Finder Window will open at that location and you can remove the iPhoto pkg files.
3. Re-install.
If you purchased an iLife Disk, then iPhoto is on it.
If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
*Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
http://support.apple.com/kb/HT4928
One question often asked: Will I lose my Photos if I reinstall?
iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.

Extensions like Ghostery, WOT or AdBlock stop working after two or three times. Restarting the webpage in a new tab the extensions will work again for several times and then stop again. Has anybody an explanation or a workaround for this bug in Safari 5?

Extensions like Ghostery, WOT or AdBlock stop working after two or three times. Restarting the webpage in a new tab the extensions will work again for several times and then stop again. Has anybody an explanation or a workaround for this bug in Safari 5?

Remove the extensions, redownload Safari, reload the extensions.
http://www.apple.com/safari/download/
And if you really want a better experience, use Firefox, tons more choices and possibilities there.
Firefox's "NoScript" will block the Trojan going around on websites. Best web security you can get.
https://addons.mozilla.org/en-US/firefox/addon/noscript/
Ghostery, Ad Block Plus and thousands of add-ons more have originated on Firefox.

Can I return my macbook air after two months?

Can I return my macbook air after two months?

where did you buy it from?
apple's return policy is 14 days

IMac - Display doesn´t work after restart

My iMac 21 Display doesn´t work after restart. If I turn it off and 1 hour later I want use it again the iMac shows the white screen with the mac logo and then the display goes off. I connected an external display to check if the iMac was ON and with the external display I can login and do everything but the iMac Display doesn´t work .
If I turn it off and wait 3 or 4 hours and then turn it back on the display works OK.
This is very strange behavior I have spent hours and hours trying to fine the solution or a similar issue but nothing so I am looking help here at apple.com
BTW When I bougth the iMac 21 there were some spots over the display so the display was replaced by the provider. The warranty has expired by now.

To tell you the truth, I don't know if they have to repalce the LCD panel or what they do for a bad backlight. In this reality of block or assembly replacement it probably involves repalcing the panel and not the backlight component. Don't know what it would cost. You'd have to ask that of a service center.

Touch ID doesn't work after ios 7.1.1 update

Touch id doesn't work after ios 7.1.1 update..
Why????

After IOS update, you first have to use passcode.
Passcode is needed when
After restarting your iPhone 5s
When more than 48 hours have elapsed from the last time you unlocked your iPhone 5s
To enter the Touch ID & Passcode setting

[Solved] Network doesn't work after hibernate?

Hello! This is my first legit Linux install so excuse me if I'm a bit slow. I installed Arch last night and everything went smoothly. However, after I tested out hibernate on my machine, the network doesn't seem to work. Just prior to the hibernate, I installed Pidgin and Skype but they worked alright, so I think that the hibernate caused a problem on eth0.
I have an Asus P8Z68-V Pro motherboard with an Intel 82579V Gigabit Ethernet Controller that's using the e1000e driver. Running "dmesg | grep e1000e" says that it is up.
I'm not entirely clear here, but from reading, I think that I have several ways of connecting to the network, including network, dhcpcd, networkmanager, and wicd. I am using wicd so I did the following (or at least I think I am only using wicd):
#rc.d stop network
#rc.d stop dhcpcd
#rc.d stop networkmanager
Similarly, I put a ! in front of network in rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# Note: Using "localtime" is discouraged, using "" makes hwclock fall back
# to the value in /var/lib/hwclock/adjfile
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# Note: if unset, the value in /etc/localtime is used unchanged
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="America/New_York"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
# Replace every !module by an entry as on the following line in a file in
# /etc/modprobe.d:
# blacklist module
# See "man modprobe.conf" for details.
MODULES=()
# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30
# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"
# Scan for BTRFS volumes at startup
USEBTRFS="no"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Vicious"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
# Wired network setup
# - interface: name of device (required)
# - address: IP address (leave blank for DHCP)
# - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
# - broadcast: broadcast address (ignored for DHCP) (optional)
# - gateway: default route (ignored for DHCP)
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# broadcast=192.168.0.255
# gateway=192.168.0.1
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=eth0
address=
netmask=
broadcast=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
DAEMONS=(hwclock syslog-ng dbus !network netfs crond wicd)
Restarting eth0 through wicd-cli still did not work. I also tried resuscitating the network via instructions on the configure network page before trying to focus solely on wicd.
I found a few similar problems on the forums by searching "wicd hibernate" and tried several solutions but they did not work. Several problems seem to be that the network doesn't work after a suspend because I guess the stuff in RAM did not get saved? But people were able to restart the network by running "/usr/lib/wicd/autoconnect.py" and I wasn't able to get this to work. As a final effort, I added "resume" into mkinitcpio.conf and placed the machine into sleep again to see if it may magically reset something but of course this did not happen .
mkinitcpio.conf:
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run first, so it may be used to
# override the actual binaries used in a given hook.
# (Existing files are NOT overwritten if already added)
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options
# like so:
# FILES="/etc/modprobe.d/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
## This is identical to the above, except the old ide subsystem is
## used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev pata mdadm encrypt filesystems"
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata scsi sata resume filesystems usbinput"
# COMPRESSION
# Use this to compress the initramfs image. With kernels earlier than
# 2.6.30, only gzip is supported, which is also the default. Newer kernels
# support gzip, bzip2 and lzma. Kernels 2.6.38 and later support xz
# compression.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
Not sure if my fstab.conf is useful but if this has something to do with settings getting "lost" in swap, here it is. Linux is on an SSD and HDD (sda and sdc) and Windows 7 is on a HDD (sdb).
fstab.conf:
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /tmp tmpfs nodev,nosuid,noatime,size=2000M,mode=1777 0 0
/dev/sda1 / ext4 defaults,noatime,discard 0 1
/dev/sda2 /home ext4 defaults,noatime,discard 0 2
/dev/sdc1 /boot ext4 defaults 0 1
/dev/sdc2 /var ext4 defaults 0 0
/dev/sdc3 swap swap defaults 0 0
/dev/sdc4 /media/data ext4 defaults 0 0
shm /dev/shm tmpfs nodev,nosuid,size=10G 0 0
Is wicd causing these problems or did I configure something else improperly? Would appreciate any help to get eth0 up again!
Last edited by TheBigCow7 (2011-09-13 17:57:20)

Ok, I think I've made some progress! Hibernate definitely affects my network connection. Could this be a kernel 3.0 problem?
I noticed that ifconfig showed eth0 without an inet addr, just an inet6 addr for the longest time. e1000e seemed to be loading up ok. I'm not certain here, but I think that meant the dhcp settings didn't stick, or something along those lines.
Trying to use dhcpcd like the instructions here did not work. By some chance, one attempt did work and while it did, I downloaded and installed dhclient. After that one successful attempt, renewing the DHCP lease via dhcpcd did not work again.
Luckily though, I found that running "dhclient eth0" worked. My DHCP settings seemed to have somehow gotten messed up after my initial, problematic hibernate to the point where none would stick, even after a reboot. Manually typing in "dhclient eth0" would get eth0 working, so I decided to add it to the bottom of /etc/rc.local, like in the example on the networking page.
Now, eth0 works after a boot. However, after the daemons load up during the boot process, my computer takes a long time to get to the login prompt (this is relatively speaking, since I am on a SSD and the boot process used to be blazing fast before). I'm pretty sure it's because I added "dhclient eth0" to /etc/rc.local.
I should say that even with these changes, after a hibernate, my eth0 still does not work and if it weren't for the edit to /etc/rc.local, eth0's inet settings would still not stick after a reboot (that is to say, the hibernate does do something to my network settings).
Is this the correct/most efficient way to fix my DHCP problem? Can I fix my "eth0 after hibernate" issue? Also, can I make my DHCP settings boot up without changes to /etc/rc.local so that I can get a fast boot again (still not sure how it was able to work before without my edit)?

After 04 months of purchase of iphone 5 the lock button is too hard. At times its not working at all. The phone has been purchased in USA now I'm not getting service in India. After all whats the point in spending so much amount without any service.

After 04 months of purchase of iphone 5 the lock button is too hard. At times its not working at all. The phone has been purchased in USA now I'm not getting service in India. After all whats the point in spending so much amount without any service.

The warranty says that Apple may restrict service of an iPhone to the country of sale, and any reliable salesperson will tell you that if you tell them that you plan to use the iPhone in another country. Such service restrictions are common with cellphones and are by no means limited to Apple's phones.
Sorry, but if your iPhone requires service, you will need to send it to someone you know in the US who can get it serviced and then send it back to you.
Regards.

Mail server doesn't work after upgrading from SL to ML

My Mail server doesn't work after upgrading from SL to ML
Mail client connects with the Mail Server wich seems to run but then they can't receive any email...
the problem seems to be related with dovecot ... in my smtp log i get this:
relay=dovecot, delay=324, delays=324/0.02/0/0.01, dsn=4.3.0, status=deferred (temporary failure. Command output: pipe: fatal: pipe_command: execvp /usr/libexec/dovecot/deliver: Permission denied
I have to say that in the usr/libexec there wasn't the dovecot directory so I just tried to create one but with no luck
Any Ideas?
Cheers
Carlo
This is my postconf -n info:
server:Data admin$ postconf -n
biff = no
command_directory = /usr/sbin
config_directory = /Library/Server/Mail/Config/postfix
content_filter = smtp-amavis:[127.0.0.1]:10024
daemon_directory = /usr/libexec/postfix
data_directory = /Library/Server/Mail/Data/mta
debug_peer_level = 2
debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5
dovecot_destination_recipient_limit = 1
enable_server_options = yes
header_checks = pcre:/etc/postfix/custom_header_checks
html_directory = /usr/share/doc/postfix/html
imap_submit_cred_file = /Library/Server/Mail/Config/postfix/submit.cred
inet_interfaces = all
inet_protocols = ipv4
mail_owner = _postfix
mailbox_size_limit = 0
mailbox_transport =
mailq_path = /usr/bin/mailq
manpage_directory = /usr/share/man
maps_rbl_domains =
message_size_limit = 20971520
mydestination = $myhostname, localhost.$mydomain, localhost
mydomain = moremoremore.it
mydomain_fallback = localhost
myhostname = server.moremoremore.it
mynetworks = 127.0.0.0/8,192.168.178.0/24
newaliases_path = /usr/bin/newaliases
queue_directory = /Library/Server/Mail/Data/spool
readme_directory = /usr/share/doc/postfix
recipient_delimiter = +
relayhost = mail.mclink.it
sample_directory = /usr/share/doc/postfix/examples
sendmail_path = /usr/sbin/sendmail
setgid_group = _postdrop
smtp_sasl_auth_enable = no
smtp_sasl_password_maps =
smtpd_client_restrictions = permit_mynetworks permit_sasl_authenticated reject_rbl_client zen.spamhaus.org permit
smtpd_enforce_tls = no
smtpd_helo_required = yes
smtpd_helo_restrictions = reject_invalid_helo_hostname reject_non_fqdn_helo_hostname
smtpd_pw_server_security_options = cram-md5,gssapi
smtpd_recipient_restrictions = permit_sasl_authenticated permit_mynetworks reject_unauth_destination check_policy_service unix:private/policy permit
smtpd_sasl_auth_enable = yes
smtpd_tls_CAfile = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.chain.pem
smtpd_tls_cert_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.cert.pem
smtpd_tls_exclude_ciphers = SSLv2, aNULL, ADH, eNULL
smtpd_tls_key_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.key.pem
smtpd_use_pw_server = yes
smtpd_use_tls = yes
tls_random_source = dev:/dev/urandom
unknown_local_recipient_reject_code = 550
virtual_alias_maps =
server:Data admin$

if this could help:
mail:setStateVersion = 1
mail:readWriteSettingsVersion = 1
mail:connectionCount = 11
mail:servicePortsRestrictionInfo = _empty_array
mail:protocolsArray:_array_index:0:status = "ON"
mail:protocolsArray:_array_index:0:kind = "INCOMING"
mail:protocolsArray:_array_index:0:protocol = "IMAP"
mail:protocolsArray:_array_index:0:state = "RUNNING"
mail:protocolsArray:_array_index:0:error = ""
mail:protocolsArray:_array_index:1:status = "ON"
mail:protocolsArray:_array_index:1:kind = "INCOMING"
mail:protocolsArray:_array_index:1:protocol = "POP3"
mail:protocolsArray:_array_index:1:state = "RUNNING"
mail:protocolsArray:_array_index:1:error = ""
mail:protocolsArray:_array_index:2:status = "ON"
mail:protocolsArray:_array_index:2:kind = "INCOMING"
mail:protocolsArray:_array_index:2:protocol = "SMTP"
mail:protocolsArray:_array_index:2:state = "RUNNING"
mail:protocolsArray:_array_index:2:error = ""
mail:protocolsArray:_array_index:3:status = "ON"
mail:protocolsArray:_array_index:3:kind = "OUTGOING"
mail:protocolsArray:_array_index:3:protocol = "SMTP"
mail:protocolsArray:_array_index:3:state = "RUNNING"
mail:protocolsArray:_array_index:3:error = ""
mail:protocolsArray:_array_index:4:status = "OFF"
mail:protocolsArray:_array_index:4:kind = "INCOMING"
mail:protocolsArray:_array_index:4:protocol = "Junk_mail_filter"
mail:protocolsArray:_array_index:4:state = "STOPPED"
mail:protocolsArray:_array_index:4:error = ""
mail:protocolsArray:_array_index:5:status = "OFF"
mail:protocolsArray:_array_index:5:kind = "INCOMING"
mail:protocolsArray:_array_index:5:protocol = "Virus_scanner"
mail:protocolsArray:_array_index:5:state = "STOPPED"
mail:protocolsArray:_array_index:5:error = ""
mail:startedTime = "2013-01-21 21:18:32 +0000"
mail:logPaths:IMAP Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:Server Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:POP Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:SMTP Log = "/var/log/mail.log"
mail:logPaths:Migration Log = "/Library/Logs/MailMigration.log"
mail:logPaths:Virus Log = "/Library/Logs/Mail/clamav.log"
mail:logPaths:Amavisd Log = "/Library/Logs/Mail/amavis.log"
mail:logPaths:Virus DB Log = "/Library/Logs/Mail/freshclam.log"
mail:imapStartedTime = "2013-01-21 21:18:34 +0000"
mail:servicePortsAreRestricted = "NO"
mail:state = "RUNNING"
mail:postfixStartedTime = "2013-01-21 21:18:32 +0000"

Upgraded to iOS6 and now charging cable doesn't work

I just upgraded to iOS6 n my iPhone 4, and now my charging cable doesn't work. No...it's not an "official" Apple charger, but even the usb cable doesn't work when I plug it into my computer. If I plug my iPad charger into it, it works fine. How can the new operating system determine what kind of usb charging cable it "wants" to accept? This charger and cable worked flawlessly before the OS upgrade.

Same problem here. I use a wall charger and have had success by unplugging the charger from the wall, plugging the adapter into the iPhone, then plugging charger back into wall. Had the same problem with a car charger and got the phone to charge using the same procedure. I'd love to know if this works for you. Good luck!

My cable doesn't work after two months I bought my iphone 6. Whether could I get a new one from apple free charge?

Similar Messages

Maybe you are looking for