My CAM cannot see 2540 storage

Hello
I Installed CAM 6.0 on my windows XP, I powered on my 2540 storage for the first time. and connect it to the same LAN that my laptop is connected to.
when I try to register the array , the CAM cannot find it. I can ping to the storage using the default IP as in the Installation guide.
what can I do to troubleshoot this and solve it?
Thanks

Assuming your 2540 is factory fresh, i.e., it hasn't been reconfigured IP wise since leaving the factory...
Reference Sun doc 820-0015-12.pdf...
The factory default IP address for controller A is: 192.168.128.101
The factory default IP address for controller B is: 192.168.128.102
Set your primary Ethernet port on your WinXP box temporarily to, for example, 192.168.128.1
Using either a cross-over cable, or you can do what I did, I used an old 10/100 Cisco switch in between the machine hosting the CAM software and the controllers. Once you have this properly setup, re-run the CAM registration process. You'll see your controller, auto-magically in CAM.
IF YOUR 2540 IS NOT FACTORY FRESH... You do have the special serial cable that came with the 2540? The reason I bring this up is because I built a project around 12 of these 2540's and I had to first create the private network to support the CAM function, and then I had to re-IP each of the controllers so that 24 controllers didn't step over themselves IP wise. Once you have the initial registration of the controller, you can change the IP address of the controller within CAM. So, if your 2540 is NOT new to you, the IP address of the controller may have changed. If so, then it will be easier to just "tip" into the controller (as oppose to the time searching the IP spectrum) and change the IP back to default, or to something else. To "tip" into a serial port is the equivalent of creating a null modem connection. If you need to "tip" into the serial port, then this is a different subject for another post.
Hope this help,
rrtays

Similar Messages

IPhoto cannot see external storage drive

Very unusual freeze-up while "repairing" iPhoto required a forced shut down. Now cannot see external hard drive with photos on it. Can you help please.

Have no idea the format of the external disk. It plugs into the back of my big monitor and has worked perfectly until I upgraded to Yosemite and iPhoto 9.8 in late December. I had difficulty setting up iPhoto at that time, and you fine folks walked me though the process in mid January. All photos were there and in the proper albums. External disk is a Seagate Free Agent GoFlex, and it is backed up on Mozy and also on an iPad Air 2.
Problem started when I simply plugged in my iPhone and iPhoto told me I had to repair my database, which I did -- it took some time. Then I had to do something with Permissions. That never ended and a Word document froze on screen while I was working on it, and when I couldn't close any tabs in Safari -- couldn't do anything, actually -- iPhoto was continuing to spin with Permissions. Finally after about 15 minutes of that, I did a hard "push the start button" shutdown. The restart took a very long time.
Since I installed Yosemite and got iPhoto working -- when it was working -- the entire computer has been a bit sluggish and slow. And for the first time ever --and I've used Macs since the 1980s -- I had a freeze yesterday. Likely unrelated, but just a data point.
(BTW, is there any way I can find the discussion I had w/you folks back when I setup this iPhoto in mid-January? Anyway to search and find it in Support?)

EA6500 - Canon sx510HS - connects, then disc - camera cannot see network

Ok. Previously I had a Netgear WNDR3300 and the camera hooked up to the G network w/o issue and stayed connected. When I am using the EA6500.
First, I only see the Guest 2.4 network when I search for a network on the camera. I do not see the 2.4 or the 5 ghz network. WPS will not find the camera and vice versa. Even if I try the PIN issued by the camera.
Second, when I manually add the camera to the network and type in the password, it connects for about 15 seconds then disconnects.
Third. When using the 'sync' option, the networks still are not seen by the camera but the camera connects to the network I manually added, just like in question 2, and stays connected for however long it takes to sync/copy any and all new images to a folder on my pc.
So I'm confused as to why the camera connected so easily with the netgear and with this Linksys EA6500 it will not keep the connection. any help would be appreciated. Thanks!
Solved!
Go to Solution.

Hi mtbmesa,
How far is the camera from your router? Aside from the camera do you have other wireless devices that's connecting fine with the router? What is the brand of the camera?
Try these settings:
SSID: should be different for 2.4 GHZ and 5 GHz
Network Mode: MIxed
Security Mode: WPA2/WPA Mixed Personal
Channel Width: 20 MHz
Channel: 3,6 or 9
Let me know if it works.

I cannot see my Iphone 4 in my device window in the finder anymore. It use to appear so I could copy the camera pictures off of it and transfer them to other folders. Does anyone have and idea how to get it back when you plug it in initially. Thanks

I cannot see my Iphone 4 in my device window in the finder anymore. It use to appear so I could copy the camera pictures off of it and transfer them to other folders. Does anyone have and idea how to get it back when you plug it in initially. Thanks

You will want to open iPhoto, go to the iPhoto menu and select Preferences. Under the General tab, next to Connecting camera opens: select iPhoto. Close the preferences and quit iPhoto. Reconnect your iPhone 4. iPhoto should open automatically and offer to import your pictures. Import them and then do what you want with them.
Best of luck.

Azure Storage Blob error - AnonymousClientOtherError and AnonymousNetworkError (why cannot see images)

I have an mobile app and I put images in Azure Storage Blob. when tested by several of our own people (on test and beta), it is all good.
But when we released it to beta and had hundreds (maybe above one thousand) of users to use, lots of them report that they cannot see images. It happens on their iPhones and also on many different brands of Android phones. Sometimes, for the same image,
on one phone it is good, but on another it doesn't show.
When I check blob log, I saw a lot of errors, mainly these two:
AnonymousClientOtherError; 304
"Anonymous request that failed as expected, most commonly a request that failed a specified precondition. The total number of anonymous requests that failed precondition checks (like If- Modified etc.) for GET requests. Examples: Conditional GET requests
that fail the check." (From Microsoft)
AnonymousNetworkError; 200
"The most common cause of this error is a client disconnecting before a timeout expires in the storage service. You should investigate the code in your client to understand why and when the client disconnects from the storage service. You can also use
Wireshark, Microsoft Message Analyzer, or Tcping to investigate network connectivity issues from the client. " (From Microsoft) - a question here, this is an error, but why it is 200?
I wonder if these are the reasons that caused my problem?
For the first one, from my understanding, it is not actually an error, it just says that the version client cached is the same as server version. But when my client side sees this response, it thinks it is an error and throw an exception and thus no image
is shown? (I actually outsourced my client side, so I can only guess). I later tested with my browser to access these images and found that if I refresh the browser with the same URL of the image, I saw error 304 on the log but I still see the image. So I
guess this is not actually a reason for my problem.
For the second one, is it because my client side's timeout is shorter than the server side's timeout? But is the timeout a connection timeout or a socket timeout? what are the default values on client side and on Azure Blob? Or is it because the network
is not good? My Azure server is located in East Asia (Hongkong), but my users are in mainland China. I wonder if that could cause problem? But when a few users tested in China it is all good.
Many of the images are actually very small, just one to two hundred k. Some are just 11k.
I cannot figure out what is the reason...

Hi,
Does any people encounter this error when they access the small picture, if this issue is only caused by large picture, please try to improve the timeout, you can also monitor your storage account from the Azure Management Portal, this may be help us
to find out the detailed error information. see more at:
http://azure.microsoft.com/en-gb/documentation/articles/storage-monitor-storage-account/, hope it helps.
Regards

I have upgraded my OS into Mountain Lion and now I cannot see any net storage disks. may someone help me? thanks

I have upgraded my OS into Mountain Lion and now I cannot see any net storage disks. may someone help me? thanks

Hi kiwirudy,
I've had the same problem more than once since I started trying to download my 14 April purchase of OS X Mountain Lion.
I found a property list called manifest.plist in my ~/Library/Application Support/AppStore folder which had a Boolean property called failed checked. I unchecked it and afterwards I was able to resume my download.
Here are some steps I've found useful:
Close the Mac App Store.
make a copy of the ~/Library/Application Support/AppStore folder. For some strange reason the Mac App Store likes to just delete it in some circumstances, which will mean that one has to start one's download again from the very beginning.
Double click on the manifest.plist in one's ~/Library/Application Support/AppStore folder.
This should open it in Property List Editor.
Expand all the nodes (holding down the alt key and clicking on the highest collapsed node should do it.
Find a key called failed of type Boolean and uncheck it.
Save the manifest.plist and close it.
Open the Mac App Store.
The red message "an error has occured" should now be gone and one should be able to resume one's download.
In the event that the ~/Library/Application Support/AppStore folder gets deleted:
start the download again (it will start from the beginning), pause it and close the Mac App Store.
copy your backup copy of the pkg file back to its sub-folder (it's a numbered folder in the ~/Library/Application Support/AppStore folder).
Open the Mac App Store and resume your download.
It should continue from where it left off.
This has worked for me so far. I'm holding my breath. Don't know if I'll still be alive when it's finished.
Regards
Nic
Message was edited by: n c h

Cannot see Wireless IP Camera via WAN

Router:WRT54GC
IP Camera: Chinese EBAY special
I have a Wireless IP Camera connected to the router. Everything works fine on the LAN.
I can connect from within the LAN using the Camera IP (&port) and the external router IP(&port).
I cannot see it outside the LAN though.
I have forwarded the correct port for the IP of the Camera and confirmed the port is open on the net. (Have tried static and automatically obtained)
I can ping the Routers external IP from the WAN but cannot see the Camera.
Have read every thread on here.
This one was helpful:
http://homecommunity.cisco.com/t5/Wireless-Routers/WRT160N-v2-with-IP-camera-BLC131-CE/m-p/300838#M1...
I couldn't ping the router until I disabled "Block anonymous internet requests" but can now.
Although putting the router ip in a browser doesn't give me remote management (if it should?)
Any ideas?

HI,
My ISP is Virgin Media (I'm in the UK)
My WAN IP is 92.236.14.192 - I can ping that from outwith the LAN. I can also use remote management using it with por t8080 so connectivity is ok.
I've forwarded port 1025 for the Cameras IP - port 80 is already in there forwarded with the routers IP, this must be a default one?
I'll change that and see if it helps.
port 1025 is open, I checked with the "canyouseeme" site.
thanks for your help!

Why I cannot see my IP-Cam on the iPad2?

Hi there,
I am writing from Germany - hope you can understand my terrible English.
I installed an IP-Cam, but I cannot see them in my iPad2.
You can see the cam here
http://kieckbusch.dyndns.org/index.htm
A friend of mine has a iPad3 and has no problems to see the cam.
What I have to do to see the picture of the cam?
Thank you in advanced,
Wolfgang

No advanced..
The WD will pickup an ip from the router.. sadly apple routers give you no info about IP of the device they pickup on ethernet.
Go to your computer .. open the network utility, and do a netstat scan .. the IP of the WD should be listed.
You can also use an iOS utility like Fing.. which does the same kind of thing.. scans the network for all the clients you have connected.
Once you determine its IP you can mount it in the computer..
But it should be accessible also by simply typing the IP or name into a browser.. did you read the instructions for setting up WD NAS in your network.

Ive dowloaded Skype , i can see my contacts web cam but they cannot see me ?

ive downloaded Skype and although i can see my contacts webcam they cannot see me ?

I'd start by making sure nothing is covering the front facing camer such as a case. Is this a problem with everyone you FaceTime or just one person. Does your front facing camera work otherwise?

Cannot see photos after upgrading to iPhoto 9.1.3

I upgraded my iPhoto to 9.1.3 and now I cannot see some of my photos. iPhoto indicates the photos are there, but all I see is blank dotted frames where thumbnails should be. When I click on one of the photos I get a gray out frame with an exclamation in the middle. I tried rebuilding the library/thumbnails, extracting using iPhoto LIbrary Manager, checking disk permissions/repairing in Utilties, etc. I tried every suggestions and recommendations I found on the net, but I still cannot see those files. I regret deleting them off my camera disc. These are the only masters I have. So I can't copy them back into the library. If anyone know how I can retrieve these files, please let me know. I also went back in my Time Machine and the same files are all empty gray frames. All I know is that the files were "visible" before the upgrade and now I can't see them after the upgrade. Any suggestions?

Hi - yes I did that last night and unlike rebuilding via control option route, IPLM did not rebuild those files. It stated they do not exist. I double checked by "Show Package Contents" and the master of those files is no longer there. My next move is to go into Time Machine and see if I can restore the library from when the files were still in there (though unseen by iPhoto) and hope the master are still recoverable. If that doesn't work, then I'm at the point of accepting that perhaps I may have lost 51 photos (1 event) during this upgrade. I'm still open to suggestions though.

Cannot see emails in the inbox, but can send emails out. why?

I bought the Galaxy S III about 3 months ago, and have been struggling to set up my personal email (my own domain hosted by godaddy.com). my gmail accounts sync up nicely from day 1.
Today, a tech rep from Godaddy.com suggested that i turn off wi-fi, and set up the account using the phone connection only. That seemed to work, and i was able to set up personal email accounts (my own domain).
Issues: i cannot see any email in the Inbox. Every time i hit the button "load up to 50 more messages", the Update icon would spin for a few seconds, but no emails show up. the message said "account last synced on date..., time....". still no emails in the Inbox.
a) i tried using the email software that came with the phone for the (the icon has an envelope and a red seal in the middle). the email was correctly set up, i was able to send emails out, but still no emails show up in my inbox.
b) i tried using the K9 email app (downloaded from apps market, free). the email was correctly set up, i was able to send emails out, but still no emails show up in my inbox.
Does anyone know what i did wrong? or is something wrong with my phone?
thanks so much for your help

qnv wrote:
good thinking.... I'm trying to set up Outlook 2010 on my desktop. it's downloading emails from the server, but because i have so many emails up there (50K) for the past few years, it's not functioning properly yet. i can see the emails and i can move them to different folders (10K emails in Inbox at a time, more get downloaded as i move emails out of the Inbox). but i cannot send emails out from Outlook on the desktop.
wonder if these 2 issues are related.
i can see, receive and send emails directly on the server (web) no problem.
I would try clearing out your inbox as much as possible, and then try it. Maybe it cannot index correctly to download because there are so many. Just a thought.

Cannot see my external hard drive on the desktop

Hi,
I am at the tail end of a large documentary project on FCP. Suddenly, this evening my external hard drive (Maxtor One Touch III, Turbo Edition, 1.5TB) becomes sluggish. I shut down (all properly) and restart and the external hard drive is no longer on the desktop (does not mount and cannot be seen anywhere).
I change ports (from one FW400 to another), try connecting to a different Mac (was running on an iMac, try connecting onto a G5) and still cannot see the hard drive. I try connecting using USB2 and still cannot see it on the desktop. I run disk utility and the hard drive shows up in menu on the left, I am able to run "verify disk" as well as "repair disk" - hard drive is fine, no errors no problems. However, I still am not able to access the drive - just does not show up on the desktop or anywhere else where I can get into it. I run the install disk that came with the hard drive (Maxtor) and a backup utility can detect the drive and shows that 1.37 TB of data is safe (so no data loss) but I can still not detect the Hard drive. I also noticed that the light on the hard drive is active indicating that the drive is being accessed.
Problem is simply that both my Macs do not show the drive regardless of how I connect them to the drive (FW400, FW800, USB2 and every port has been tried).
Need help here...please....
I realize this might be more suited for a general OSX or Hard drive issue, but since I have always got great answers from FCP users that I am posting this question here.

Hello all,
Thank you for all your comments and suggestions. I downloaded Disk Warrior 4 from Alsoft - paid $108, followed the instructions to the letter (after reading and rereading sevral times) and ran the utility...it detected the Maxtor HD, pointed out several errors, repaired the errors, and then gave me the option to preview the new and compare to the old HD...this is where things went wrong. There was no HD to be seen - new or old...same problem. HD is not visible on my Finder, on the Disk Warrior Preview or on the desktop. I went ahead and rebuilt the HD...all errors fixed, Disk Warrior states that all is fine and dandy and that my hard drive should be perfect and I can access it...BUT its still not there, I cannot see it on the desktop nor anywhere else.
It shows up in Disk Utility as a page icon - but I cannot access it.
So, unfortunately for me...my problem still remains and I am now out a hundred bucks!
Please, anybody out there - who can give me some direction - I would greatly appreciate it.
BTW, the data is still all there and the light on the front of the drive keeps flashing indicating something is going on...but drive is not mounted, invisible.
I read on the Maxtor packaging something about a built in Maxtor DriveLock - a password protected security measure against theft and loss...could I have inadvertently activated that and that is causing the problem...please advise.

AEBS cannot see both disks in 2 disk enclosure set to JBOD

I have a MacPro 3.1 and AEBS, the computer runs 10.6.8 and Win 7. All most recent updates installed on both OSes and the AEBS. I have a generic (bought at Fry's) HORNETTER, 2 disk external USB enclosure containing two (2) 500GB hard drives, both formatted to FAT32 for easy sharing purposes with win, which is connected to the AEBS via its USB port.The enclosure is set to JBOD (Just a Bunch of Disks), so I can see each one individually. The enclosure is externally powered. I have had problems in the past with this set-up off and on. Now it is VERY tempermental, sometimes it works, most times not and now over the last couple months it has stopped working for all intents and purposes.
The problem I get is that the AEBS does not see both drives, only one. This happens in OS x and Win 7.
I get an error saying there is a problem with the disk, connect it to the computer directly and run Disk Utility to check for errors. So I do this every time and it returns no errors. Both disks can be mounted no problem if connected directly to the computer. But if I unplug it from the computer and plug it back into into the AEBS it stops working again.
I have this same problem with my HTPC Mac Mini 2.1 (C2D 2/0Ghz). I tried connection it with the same config and got the same problem, only one disk shows of the two in the enclosure.
Is there anything I could do to resolve this? I have searched high and low for a direct answer, but only see confusing responses and nothing direct on point. I apologize if this is a common issue.
I am not trying to do any Tim Machine backups, just using it one drive to store my media (music, video) and the other drive as a extra storage/share volume/hand backup of important files. I like having it available off the AEBS so I can access the music and video from my HTPC Mac Mini and my DVR Windows machine, as well as using them both as a easy swap for mac files I drop there for when I'm booted into Windows.
Any help would be appreciated.

UPDATE: I read some tips on other related issues, and so I tried connecting a POWERED USB HUB (a Targus brand 4 port AC powered USB hub I had lying around) to the AEBS and then the external enclosure to the hub.
No success, and two different problems.
In OS X I can now SEE both disks (where before only saw one disk), but the problem now is even though I can see both disks I can only access one (the one I could NOT access before). The disk I could access before is not visible but when I try to double click on it to mount it, i get a spinning blue circle and eventually the request times out with an error which makes no sense, but says:
"There was an error connecting to the server “Lou's AirPort Extreme”. Check the server name or IP address, and then try again.
If you are unable to resolve the problem contact your system administrator."
When dismissed this is followed byt eh additional error message:
"The operation can’t be completed because the original item for “BACKUP” can’t be found."
On Win 7, I now cannot see the AEBS at all, and neither disk is visible.
*sigh*
Back to square one......
SECOND UPDATE: Connected a USB thumb drive to the Powered HUB and it shows up fine. So now I am just totally confused.

Finder cannot see AirPort Time Machine drives

I'm running OS X 10.9.4 on a MacBook Air (2 GB memory, 64 GB SSD storage).
I'm using an AirPort Time Capsule (with Time Machine) as my router and backup. I have an additional hard drive connected to the USB port on my AirPort Time Capsule.
For over a year the entire configuration has worked well: Backups are done, and I can access both the AirPort Time Capsule internal hard drive and the external hard drive from my MacBook Air, and from any other device on the network.
For the past few weeks, Finder (on my MacBook Air) sometimes cannot see either drive (internal or external) on the AirPort Time Capsule. Backups are still okay, and PCs are still able to access and use both drives on the AirPort Time Capsule. Also, software on my MacBook Air CAN see and use the drives. For example, if I have a photo on one of those drives that I want to post on Facebook, the "finder" window that appears when I click "Upload Photos/Video" (on Facebook) sees the drives, and can upload the photo from the drives. The ONLY time I cannot see the drives is when I try to access them with Finder. (See photos.)
At first, Finder occasionally could not see the drives, or sometimes it took a minute or two to see the drives. Now, Finder generally cannot see the drives, no matter how long I wait. My PCs, and ALL SOFTWARE on the MacBook Air CAN ALWAYS see the drives. Also, Finder can ALWAYS see ALL THE OTHER shared drives on the network (on the PCs, for example), even when it cannot see the drives on the AirPort Time Capsule.
Can anyone tell me what is going on?
Using Finder:
Using Facebook:

With the shared folder open, select
View ▹ Show View Options
from the Finder menu bar. In the dialog that opens, select
Arrange by: None

Leopard Mac cannot see hard drives on Tiger Macs

Running Leopard 10.5.2 on a Mac Pro 3GHz 4-core w/6GB RAM. I cannot connect to any hard drive / root directory on any Mac on my network running Tiger (10.4.9, .10 or .11) or Panther or OS9. I have 4 Macs on the network but only one running Leopard.
The Mac running LeopardI can connect to the User folder on any Mac running Tiger but cannot see any hard drives' root directory on any Mac running Tiger . No hard drive can be accessed from a User folder even if an alias of the Tiger drive is placed in the ~/User/Public folder.
The reverse works as usual. Any Mac running Tiger can see any hard drive on any networked Mac including Macs running Leopard.
Has anyone else encountered this issue &/or found a workaround? After 2 hours with Apple Tech Support including a system specialist, they confirmed this behavior in Leopard Macs networked to Tiger OS Macs. (Hard drives can be seen between all Macs running Leopard) It was theorized by one of the Apple techs that the behavior was engineered to encourage upgrading all Macs to Leopard. BAD idea! I requested this be reported to Apple engineering.
Any ideas?
TIA!

Download and read the documentation for Carbon Copy Cloner which is handy and what a lot of us have used over the years to clone, migrate and backup or manage drives and storage.
I think 500GB is overkill for boot drive as most of your apps and OS only need less than 150GB, and all of your data and media and home folders can be anywhere you want and not on the boot drive. Also, Apple way over charges for 2TB drives and no reason or value to do so. That is history now but fwiw.
You could I guess setup one 2TB as boot drive easy enough. Then migrate etc. Make that a backup of everything. Then manually or with CCC or other you can clone just what you want to SSD and to the other 2TB drive.
Apps should always go to the boot drive, the SSD in this case, and not to other locations. No benefit putting them elsewhere.
When you migrate are your files on TimeMachine or just standard files and folders? and can't selectively copy? Honestly never found need to use M.A. more than once probably.
http://support.apple.com/kb/HT4889
http://www.apple.com/support/timemachine/

My CAM cannot see 2540 storage

Similar Messages

Maybe you are looking for