My camera can not switch side

My camera could not switch side. It does not flip, and does not have the button that it suppose to have.

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Similar Messages

FaceTime won't start because my camera is not switched on. How do I switch the camera on? Am using Mavericks on a MacBook Pro

FaceTime won't start because my camera is not switched on. How do I switch the camera on? Am using Mavericks on a MacBook Pro

You're most welcome, FlutePixzy!
FlutePixzy wrote: ... Apple Care netted nothing... Except they noted I have an older laptop...
If your older laptop meets Apple's published minimum OS X Mavericks: System Requirements, Apple technicians can make it work on your older laptop (if you decide that any service cost is worth the expense.) If so, call Apple Care again and politely ask them how to proceed. Ask to speak with a supervisor or manager if you don't get satisfaction. Limit the discussion to your Mac's problem(s).
Your assessment of Apple's shortcomings are unlikely to help anything.
Technicians may need to inspect your Mac before they can give you an accurate service cost estimate. There may be a separate charge for the inspection of your older Mac, so ask about that, too, if cost is an issue for you.
Message was edited by: EZ Jim
Mac OSX 10.9

Sometimes when I play songs in Itunes by double clicking on them, Itunes will place the song as the first one on the album. It will chnage the order of the songs on the album, and I can not switch them back to the correct order.

Sometimes when I play songs in Itunes by double clicking on them, Itunes will place the song as the first one on the album. It will chnage the order of the songs on the album, and I can not switch them back to the correct order. This onloy seems to happen when I double-click on the song to play it in itunes. If I just hit play, this doesnt happen. As a result, I have several albums now in which the songs are in the wrong order. Its very frustrating, as this error then transfers over to my ipod every time I sync it. When I choose the info. for the songs, it has them correctly listed (i.e., it lists the songs as being #1 of 19 on the CD, for example). But then the song will have placed by Itunes as #5 of 19 for whatever reason. Itunes does not do this every time, but does it with enough frequency to be maddening. Any thoughts?

The problem of tracks becoming de-linked between iTunes and the music files in your iTunes music folder happens for different reasons - this seems to come up fairly commonly in this forum.
The solution can be to locate each song in the iTunes library, as you mentioned - or, but wait, before I get to that...
trouble finding the original track in your iTunes music folder? maybe look for it under compilations, or if not using the 'group compilations preference' then look in the folder under the songs artist name, but what song artist name iTunes uses depends on what you have in the metedata tag spot for album artist or song artist. Any varyation in artist name spelling, in the menu item 'get info' metadata for any selected individual track will cause iTunes to create that as a separate artist folder in the library, even names like 'various' or any difference at all (even the word 'the' can change where in your iTunes music folder a track gets placed by iTunes). You can try to use the finder function of find file (finder munu item outside of iTunes) to locate hard to find items.
Back to how to re-link any de-linked tracks .
There may be scripts that can help re-link de-linked music files - or, at least provide you a list of such files, Scripts are easy to install and use...
at Dougs Scripts, there is one called iTunes Track CPR that might work
http://dougscripts.com/itunes/scripts/ss.php?sp=itunestrackcpr
or, if you just want a list of de-linked tracks, go to
http://dougscripts.com/itunes/
and find the script called List MIA's, this will create a text file listing all de-linked tracks
if you review the thread at
https://discussions.apple.com/thread/3633708
also the thread at
https://discussions.apple.com/message/17513078#17513078
you may find more insight into dealing with this kind of issue there, although some of that thread may not apply to your case, aspects of it might help.
Good luck.

Tabstrip control can not switch (Do not respond when focus on field of subscreen)

Hi Colleagues,
     I have met with a very strange question, which worries me a lot these days. Would you please help me with it?
     The problem is like this:
     1. In normal case, I can switch to another tab when I click it. Please see picture in the attachment (Tabstrip1.png)
     2. But when I click on field on the subscreen of one tab, set focus on one field, in the picture of attachment switch2.png, I can not switch to another tab, it just does not respond. I really do not know why this happens.
     Could any colleague give an answer or hint about it? Thanks a lot!!
     You can access the program by TCODE: EPIC_RPR on EBJ client 003 or QI3 system client700 .
BR,
Chris

yea thats what i thought, thats the most sensible answer that they expect you to
know it.
but... have you taken any of the them? would love to hear from someone thats taken a few, i wasn't even sure if i'd put this post in the right forum to be honest.
just seems odd why they say 95% of the material is in the prep stuff seems too easy.
i'd have thought that since the cs4 exam had that many more questions that the cs5 exam would have even more prep material but obviously not so.

Buy adobe photoshop elements 10 Itunes under order number MHMKW49V6Q the March 3, 2013 and is in German language and can not switch to English

Buy adobe photoshop elements 10 Itunes under order number MHMKW49V6Q the March 3, 2013 and is in German language and can not switch to English

The Adobe distributor for Croatia is:
HSM Informatika
Grada Mainza 19
Zagreb 10000
Croatia
Tel: +38513908930
Fax: +38513758850
There is a download store for Eastern Europe:
https://store2.adobe.com/cfusion/store/html/index.cfm?event=displayProduct&categoryOID=703 2501&store=OLS-EU

I can not switch to Indesign in Bridge

I can not switch to Indesign in Bridge@

not sure how to read it all...this is what it says
ATA Bus:
ST380021A:
Capacity: 74.53 GB
Model: ST380021A
Revision: 5.05
Serial Number: 3****T
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ATA
Unit Number: 0
Socket Type: Internal
OS9 Drivers: Yes
S.M.A.R.T. status: Verified
Volumes:
Macintosh_HD:
Capacity: 74.53 GB
Available: 39.13 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s5
Mount Point: /
ST380021A:
Capacity: 74.53 GB
Model: ST380021A
Revision: 5.05
Serial Number: 3****T
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ATA
Unit Number: 1
Socket Type: Internal
OS9 Drivers: Yes
S.M.A.R.T. status: Verified
Volumes:
Macintosh_HD1:
Capacity: 74.53 GB
Available: 68.93 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s5
Mount Point: /Volumes/Macintosh_HD1
ATA Bus:
ST380021A:
Capacity: 74.53 GB
Model: ST380021A
Revision: 5.05
Serial Number: 3****T
Removable Media: No
Detachable Drive: No
BSD Name: disk1
Protocol: ATA
Unit Number: 0
Socket Type: Internal
OS9 Drivers: Yes
S.M.A.R.T. status: Verified
Volumes:
Macintosh_HD:
Capacity: 74.53 GB
Available: 39.13 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk1s5
Mount Point: /
ST380021A:
Capacity: 74.53 GB
Model: ST380021A
Revision: 5.05
Serial Number: 3****T
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Protocol: ATA
Unit Number: 1
Socket Type: Internal
OS9 Drivers: Yes
S.M.A.R.T. status: Verified
Volumes:
Macintosh_HD1:
Capacity: 74.53 GB
Available: 68.93 GB
Writable: Yes
File System: HFS+
BSD Name: disk0s5
Mount Point: /Volumes/Macintosh_HD1
<Edited by Moderator>

TS1559 can not switch on wifi or the bluetooth on my iphone 5

can not switch on wifi or bluetooth on my iphone 5 please help

There are many, many threads on this forum about this issue. Do a forum search for "wi-fi greyed out" and see if any of the solutions therein will work for you. Best of luck.

My IPAD just stop to work. Blocked. I can not switch it on or off. Nothing happens. What can I do?

My IPAD just stop to work. Blocked. I can not switch it on or off. Nothing happens. What can I do?

If you mean that the screen is frozen then have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

I can not switch on my mobile why ?

Could you please suggest me regarding my problem?? I can not switch on my mobile?

Very vague.
Charge it?
Maybe if you were to explain, more help could be given

MY IPAD CAN NOT SWITCH ON OR SWITCH OFF

MY IPAD CAN NOT SWITCH ON/OFF. SCREEN IS BLACK AND ONLY RUNNING CYCLE ON THE CENTER OF THE SCREEN. LOOKS LIKE THAT STACK????

Is your iPad charged? If so, hold the power/sleep button and home button until the apple logo appears in center of the screen and it restarts. Then what happens?

Hello, I IPAD3 to upgrade 6.0 system, rear camera can not open up, open the camera stuck in the rotating screen

Hello, I IPAD3 to upgrade 6.0 system, rear camera can not open up, open the camera stuck in the rotating screen

Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. The screen will go blank. Be patient, the device will power ON again in the normal way. It is app and data safe!]

I can not switch to the front camera on my iTouch 4g.

I have owned two 4th Generation Ipod Touches. After having both for over half a year, their front cameras will not work. I do not usually use the front camera. When I attempt to switch to the front camera from the Camera App (or from the Lock Screen) the Camera/Video button begins to flicker and the screen will either show the shutter or blackness. When attempting to switch the camera on Instagram, it notifies me that there was an error launching the camera. on my oldest device I was able to restart the Ipod and the front camera would work for a while before I would be required to restart it again. My newest device used to be the same way, but now it will not be fixed by restarting/shutting down/reebooting the device.
Other Details:
1st Ipod: Dropped- Front camera shattered and top left corner of Ipod cracked; Screen turned completely white when device was cold; Glass replaced once
2nd Ipod: Dropped- Bottom left corner dented and one thin line arching from corner to right side through the screen; Slow in taking pictures (back camera)
If this is a software problem, I would like to know if it can be fixed with at-home fixes.
If this is a hardware problem, must the entire devie be replaced or just the glass?
Thank You

If you restored to factory settings/new iPod and still have the problem then it is a hardware problem.
I suspect that replacing the screen will not fix the camera problem unless the problem is due to a loose connection since replacing the screen could restore that connection.

Camera can not open.

I can not open the camera app!
The FaceTime front camera is still working,but when I change to back side camera, the app will be stuck.
I already try to restore the all set up and the factory setting.

I already try to restore the all set up and the factory setting.
Then you most likely have a defective camera. There's not much more you can do other than return to Apple for possible warranty replacement, if still under warranty.

APEX 5: can not switch the developer env to GERMAN

Hi,
After some days dealing with the english version, I installed the German Language pack as mentioned in the Installation Guide with the langDE.sql. If I swich to German on the developer login page, I can run the appliaction, but i can not call any edit page.
There is only a error message ORA-06502: PL/SQL: numeric or value error: character to number conversion error .
May be I missed to set a language environment or something like this? Any advices for me, please?

Hi Norbert,
thanks for letting us know. The issue is already tracked with bug# 20929652. It's an NLS issue with the Splitter used on different pages. May I ask which OS and Browser you are using?
To workaround the issue, login with English user interface, go to SQL Workshop -> SQL Commands and execute
begin
    apex_util.remove_preference( 'F4000_1157687726908338238_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4000_203904827661009901_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4000_203906404237009921_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4500_1157684150404338202_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4500_1157684743709338208_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4500_1157684935965338210_SPLITTER_STATE' );
    apex_util.remove_preference( 'F4500_1157686386582338224_SPLITTER_STATE' );
    commit;
end;
to remove the currently used splitter values. Now you can go back to the main page to switch your Builder language to German.
Regards
Patrick
Member of the APEX development team
My Blog: http://www.inside-oracle-apex.com
APEX Plug-Ins: http://apex.oracle.com/plugins
Twitter: http://www.twitter.com/patrickwolf

Camera can not be detected! any ideas?

i am programming a microsoft which just likes NetMeeting,and i have a problem now.this question might seem silly to you ,but i am a new jmf_er,so i need your help!
to detect camera ,i wrote the code as follows:
Vector list = CaptureDeviceManager.getDeviceList ( null );
if ( list != null )
for ( int i=0; i<list.size(); i++ )
devInfo = (CaptureDeviceInfo)list.elementAt ( i );
name = devInfo.getName();
System.out.println(name);
if ( name.startsWith ("vfw:") )
System.out.println ("DeviceManager List : " + name );
capDevices.addElement ( new MyCaptureDeviceInfo ( devInfo ) );
but i discovered that there is no name starts with ("vfw:")!and the camera can be detected when i use another microsoft !
i do not know what is wrong ,
any ideas are welcome,thank you!
Regards
Adigan

The ist thing is that ur code is incorrect
the last statment (addElement)is not meant to be here
use the following code..
CaptureDeviceInfo devInfo=null;
Vector list = CaptureDeviceManager.getDeviceList ( null );
if ( list != null ){
        for ( int i=0; i<list.size(); i++ ){
                          devInfo = (CaptureDeviceInfo)list.elementAt ( i );
                      String name = devInfo.getName();
                      if(name.startsWith ("vfw:")){
                           dExist=true;
                                                                         break;
     if(dExist==true){
               MediaLocator m = devInfo.getLocator();
                DataSource ds = null;
     try {
          ds=Manager.createDataSource(m);                                Player player = Manager.createRealizedPlayer (ds);
                   player.start();
                    Component videoScreen= player.getVisualComponent();
          Frame frm=new Frame();
          frm.setBound(100,100,300,300);
          frm.add(videoScreen);
                                          frm.setVisible(true);
     } catch (Exception e) {
else{System.out.println("no device exist");}

My camera can not switch side

Similar Messages

Maybe you are looking for