My Canon MX 892 prints blank pages.

For a couple of days my MX 892 colour printing has been wrong - too much yellow. Suddenly, this morning it prints completely blank pages. It behaves as though it's printing ok but not a drop of ink. The tanks are ok and I've deep cleaned the head and reset all settings but I still get no ink on the paper.
Any advice would be appreciated
Canebee

I have exactly the same issue with same printer on my brand new iMac. Quite disapointing !

Similar Messages

Canon Printer: Printing blank pages

CAPTV330_MacOSX_ukEN.dmg. Downloaded this driver. Was printing correctly. Now printing blank pages, while printing some graphic outlines.
When printing on Adobe, it prints fine. Also tried Print Bitmap mode, worked. I suspect its printing in Postscript mode, while I believe the printer, then doesn't understand the mode.
Removing the printer from /Library/Printers/Canon/CUPSCAPT/ doesn't help.

Problem Solved!
1. Open System Preferences > Print & Fax
2. Move your mouse over the Printers list
3. Hold down the Control button and click the mouse
4. Click the "Reset printing system ..." popup
Then go to http://support-sg.canon-asia.com/contents/SG/EN/0100220001.html , download and install this new driver.
After that add your printer again and select the drivers.
It worked for me.

Windows 8.1 printing blank pages from all apps

Morning Tech Support: My favorite people!! This just began within the this week where what ever appl I attempt to print from, prints blank pages. Upon viewing the print spooler, it shows doc going into printer okay, no probs w/ margins
or page size (already checked). Printer is Canon MG5400 (newer). I've already rebooted turned on the computer where the computer is installed. What else could it be. Working on installing new updates that just came down as well.
HELP!!!!
s.hamel

Try install all updates for Windows and check for update for latest version of your printer's software.
Try run a test print and check if it works.
Also check the cartridge and make sure they are okay.
You may contact Canon's support too.

Pixma was working just fine until I replaced 3 of the ink cartidges. Now it only prints blank pages

Pixma was working just fine until I replaced 3 of the ink cartidges. Now it only prints blank pages. It does the same thing from my computer as from the printer itself. Also passes the device maintenance tests, including all the colors and the alignment. Does anyone have any ideas?
Thanks

Hi, Patty8888!
So that the Community can help you better, we will need to know exactly which printer model you're using, which operating system is running on your computer, how your printer is connected to your computer. That, and any other details you'd like to give will help the Community better understand your issue!
If this is a time-sensitive matter, our US-based technical support team is ready to help by phone at 1-800-OK-CANON (1-800-652-2666) weekdays between 10 AM and 10 PM ET (7 AM to 7 PM PT).
Thanks and have a great day!

Windows Machine Prints Blank Pages

Purchased the new Airport Extreme n this week. I was able to get the wireless working with my iMac and Windows XP laptop, however I am having printing issues.
I have a Canon 4200 hooked up to the Extreme via a USB hub. I was able to get the XP machine to see the printer, but when I print, it prints blank pages. I can tell that it recognizes the document because it prints blank pages for however many pages are in my document. I went through the iFelix steps but get the same result.
I searched through the forum (in addition to other independent mac forums), but most people's issues are with the Extreme simply recognizing the printer.
Please help!
Airport Extreme N

Can't see the channel would make any difference, although specifying a channel might be better than letting it wander.
There won't be any printer settings in the extreme settings (didn't realise that was what you were after) they will be in the printer utility on your mac. Again you have probably done it but your printer should be set up as a network device not a s a USB device. Sorry I can't be of any more help at the moment.
It might encourage you to know that I had my printer working just fine, I changed some setting just as a trial and it started printing full pages of yellow, I changed the setting back and it was OK again. Only thing is I don't remember what setting I changed.
Have you tried WEP instead of WPA. and have you tried restarting (not resetting) all your devices.
Got to go to bed, 5am here, hope someone else picks up this thread with you, there are a lot of good people here.

Why does Ipad mini print blank page

I have a wifi/airtime enabled Canon printer. I can print a picture OK from my laptop but when printing the same picture from my Ipad mini, only a blank page is printed. A text document is printed OK.

I have a similar problem: In Notes my Canon MX922 which is AirPrint enabled prints only blank pages for some Notes files. For others it works ok. But, if I copy text from a file for which printer only prints blank pages to a Notes file that I was actually able to print, the previously ok file becomes infected with the same disease and I only get blank pages. Really annoying!

How to print blank page in script

Hi all,
how to print blank page in script

Hi,
Try the command /: NEW-PAGE. Let me know if it is working.
Ray

REPORT SERVER 6i Patch1 PRINTING BLANK PAGES

I have a problem that is occouring on three different report servers. It will start printing blank pages instead of the report and the only way to get it back to normal is to stop and reastart the service. I get this on a version 6, version 6i and version 6i patch1 report servers. It makes no difference what call method I use (command line or OCX control). I can also force this behavior on one of the servers by selecting a HP 895C as the default printer in the windows printers and then starting the service. All pages print blank after that. At the customers site it appears to be random as to when it will start printing the blank pages.
Any ideas on what the fix is for this?
null

Is there any ideas on this?
We have a Reports 6i server up and running and I'm getting stuff out OK to postscript printers, but some HP older printers are just spitting out blank pages. Is there a desformat= that I need to set differently? I've tried most of the options ( dec, psport, psland, hpl... all blank )
Appreciate any help, I haven't used this stuff long, so am quite naive about how it hangs together.
null

HP LaserJet 4MP Printing Blank Pages

Hi there,
This is perhaps OT, but a recent issue with my HP LJ 4MP is causing me great anguish and heartache.
Suddenly, for no apparent reason, my HP is producing blank pages. It just runs and runs spewing out blank pages.
I've tried all the IO resets and a cold reset. Unplugging and leaving idle. Unplugged the Asante bridge between the serial and the CAT 5.
After a while I can get it to stop printing blank pages, it works fine for a while, then the interminable blank pages start again.
Has anyone seen such an issue? Any known resolution?
Thanks a bunch,
Matthew

Matthew,
I too use HP LaserJet 4MP and AssanteTalk Bridge connected to computer via ethernet crossover cable and link from Assante to both my LJ4MP and HPDeskJet855cse, using BelKin QuikNet adapters in a string using RJ11 jumper cables.
My HP driver software is HP8.1.1.
I Never use "BackGround Printing".
I Never use "DeskTop Print Monitor".
The only time I can remember multiple blank copies is when I used to use "Print Monitor and BackGround Printing".
Clear your preferences and get rid of Print Monitor and Don't use BackGround Printing.
HTH.......Bob

HP LJ 1320 only prints blank pages

The printer will only print blank pages. Test pages are also blank (including from the Green Button). This is a recurring issue. It was solved in the past by fiddling with the cartridge and mechanical parts inside (we don't know what exactly sovled the problem). Toner is full. I ran the HP Diagnostic Tool and it found no "X"s.
I verified that the following mechanical parts are functional:
switch on left side of cartridge door
plastic tab on top right of door, which connects to laser spring/switch
spring/switch underneath top panel, which seems to enable laser
arm/gears to enable paper spindle
contacts on printer-side of toner/printer connection (this part slides from side to side 1/4 inches, and I tried printing with it in various locations)
There seem to be no error beeps/tones when the printer starts up or when I close the toner door. (However, it was capable as I bypassed one of the switches and it made an error tone at that point).
I think it must be something like a dead laser (however, I think the laser is invisible and we cannot test tosee if it is functional).
Any other ideas/solutions would be appreciated.
I forgot to mention that the low-toner light is not lit, and we've had this issue with both new and old-working toners cartridges.
Message Edited by measterbrook on 11-10-2009 09:57 AM
Message Edited by measterbrook on 11-10-2009 09:58 AM

Has anyone else had this problem? I have a LaserJet 1320 that started doing the exact same thing last week. I'm wondering what I have to do to get it working again. Anyone know something about these units?

HP Officejet Pro 8000 Printing Blank Pages Instead Of Data And Also Reorienting Itself

Hi all
We have a wireless HP Officejet Pro 8000 in our office (but via cable, not wireless) to a network. The printer is occasionally printing blank pages instead of say a spreadsheet selected to print.
The other issue is that if you say are printing two copies of the same spreadsheet, one prints okay (say landscape) and the second copy, selected at the time of printing, prints it portrait but only part of the left hand side of it and the rest is blank. Coming out of and going back inthe file usually recitifes this. But it does it again any time it feels like it.
We did have an upgrade, where our IT guy took away our desktop boxes and replaced with smaller base units and everything is run from a main server and alsoan upgrade from Windows 2000 to Network. Problems started after this and the IT guy did update the printer driver.
Please would anyone be able to assist? Any help for this frustrating problem gratefully accepted!
Thanks,
Saxplayer67

So the issue with the 8000 printer is periodic print jobs do not come out as you are wanting them. Is that right? This is interesting, just from the point of view that generally speaking issues like this are like a light switch, they are either there or they are not - they usually don't come and go. That being said, we are going to see what we can do to resolve this. First I am going to recommend that we perform a clean installation of the printer after uninstalling it from the machine. By the way, what is the operating system you are working with - Is it Windows 2000 Network?
First if you use a USB cord, make sure to remove it. Do not plug it back in until the software directs you to. Then go through the Devices and Printers, Programs and Features and Device Manager folders and insure that all copies, files, and programs related to the printer are removed. Then as directed, restart the computer.
In the START menu type "%temp%" and press ENTER. Here I want you to press Ctrl+A and hit DELETE. Some of the files will not allow you to delete them, skip those files and delete the majority that allows it.
Then follow this link to download the full feature software and drivers for the printer:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&lc=en&dlc=en&product=3762364
Install that and let me know the result!
Have a great day!

HP Deskjet 3050 All-in-One Printer J610a is printing blank pages

Your HP Deskjet 3050 is printing BLANK PAGES?
The printer ejects blank sheets of paper when printing. Some or all the printed pages might be partially blank or half printed. It can be the software that you are printing from or program. Sometimes it can be the actual print head needs cleaning or cartridges are low.
Here is a link that will provide you with steps that will get the issue resolved. In this document you will have different Operating Systems. (Windows XP, Windows Vista, Windows 7 and Mac OS X) Software.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02744420&tmp_task=solveCategory&cc=us&dlc=en&lc...
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.
This question was solved.
View Solution.

Yes, the link is down.
See if you can print a self-test page or printer status report from the printer itself. If so, then it is a software or connection issue.
If you can print test page, try to use a different USB cable. Also, you can uninstall and re-install the software and drivers.
If you are NOT able to print a test page from the printer, try to clean the cartridges with lint free cloth and water.
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

Printer prints blank pages

I received a message low toner. Before I replaced the toner the printer printed blank pages. After I replaced the toner, the printer printed for awhile the same day and now prints blank pages. I took out the toner and moved it back and forth and replaced it and still nothing on the paper. Do I need a new printer? Thanks, Sally

Regarding blank pages printing:
Which printer model do you have?
Does it print a blank self-test page?
What operating system are you printing from, and what application (if not all apps)?
What driver are you using?
More info from you will help us offer suggestions to resolve the blank pages issue.
We enjoy helping if we can, as these forums have helped us frequently.

When downloading a pdf, the print command show a document in the preview but only prints blank pages

When downloading a pdf and using the print command, it shows the correct document in the preview but only prints blank pages. If I use the save command and try to open with Acrobat 11.0.07, it says it wasn't correctly decoded and can't open it. If I do the same thing on my old Macbook (10.6.8) all works fine from the same website with the same document. Any ideas?
D

This article maybe help to you, change pdf file type to other application like adobe reader, See:
* https://support.mozilla.com/en-US/kb/Managing%20file%20types

Firefox will show PDF's but prints blank pages. Other browsers are fine, safe mode has no effect.

Currently on an HP laptop, Win8, printing to a HP Color Laser, no previous problems; all of a sudden, PDF's are printing blank pages. I can see the page fine. Safe mode without any addons has no change. I printed my taxes out and had no problems.
I've used IE (shudder) an been able to print PDF's fine. I have no PDF software itself on the computer, just using the browsers native support. EXTREMELY FRUSTRATING. Searching shows problems loading PDF's, but my problem is printing PDF's. Using version 29 of Firefox. Anyone got any tips or clues how to hunt this down? Really close to introducing my computer to Mr. sledgehammer.

Thanks, appreciate the links for PDF driver add ons, this will be my last resort if nobody else can figure it out. I don't use Acrobat because of all their bloatware and hidden installs. I still would like to know why Firefox started printing blank pages in PDF's, but can still open the PDF's, very frustrating. Seems like a few other people are having the issue as well.

My Canon MX 892 prints blank pages.

Similar Messages

Maybe you are looking for