MY CISCO 6800 IA CAN NOT JOIN TO THE PARENT

Hello
I have a 6807XL with VS-SUP2T-10G, and the 10 Gbps Line Card WS-X6816-10GE, when I tried to provision the join of the 6800IA, I got theses errors.
CORE(config)#interface tengigabitethernet 1/1/1
CORE(config-if)#switchport mode fex-fabric
Command rejected: Mode fex fabric not allowed on non FEX capable slot
CORE(config-if)#channel-group 1 mode on
Command rejected (Port-channel1, Te1/1/1): Cannot be part of bundle, Non FEX Capable Slot
What should be the solution for it??
Regards
Rafael Barba

Hi,
Does your system meet all the requirement for FEX?
Q. What are the different components of the Instant Access solution?
A. The Instant Access solution requires new Cisco Catalyst 6800ia Instant Access clients and Cisco Catalyst 6500 or 6800 Series Switches (Instant Access parents) with Supervisor Engine 2T and WS-X6904-40G-2T line cards. Instant Access requires Cisco Catalyst 6500 or 6800 Series Switches configured for Virtual Switching System (VSS) mode, and we recommended having a pair of switches to provide the maximum level of redundancy and load balancing. Note: In networks where a pair of Cisco Catalyst 6500/6800 is not available, a single Cisco Catalyst 6500/6800 switch may be used when configured for VSS mode.
Link:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6800ia-switch/qa_c67-728684.html
HTH

Similar Messages

Cisco LAP 2602 can not join Virtual WLC

dear all,
i just install Virtual WLC and i remove WLC 2504 , i install & configured it , but LAP can not join. it was work fine with WLC 2504.
i used the same network topology with the old WLC.
i receive this error logs.
*spamApTask4: Feb 04 06:01:30.082: <<<< Start of CAPWAP Packet >>>>
*spamApTask4: Feb 04 06:01:30.082: CAPWAP Control mesg Recd from 10.192.200.93, Port 26711
*spamApTask4: Feb 04 06:01:30.082: HLEN 4, Radio ID 0, WBID 1
*spamApTask4: Feb 04 06:01:30.082: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask4: Feb 04 06:01:30.082: Msg Length : 155
*spamApTask4: Feb 04 06:01:30.082: Msg SeqNum : 0
*spamApTask4: Feb 04 06:01:30.082:
*spamApTask4: Feb 04 06:01:30.082: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask4: Feb 04 06:01:30.082: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask4: Feb 04 06:01:30.082:
*spamApTask4: Feb 04 06:01:30.082: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083: WTP_SERIAL_NUMBER : AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask4: Feb 04 06:01:30.083: Maximum Radios Supported : 2
*spamApTask4: Feb 04 06:01:30.083: Radios in Use : 2
*spamApTask4: Feb 04 06:01:30.083: Encryption Capabilities : 0x00 0x01
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask4: Feb 04 06:01:30.083: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask4: Feb 04 06:01:30.083: WTP Mac Type : SPLIT_MAC
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083:
IE : UNKNOWN IE 207
*spamApTask4: Feb 04 06:01:30.083: IE Length : 4
*spamApTask4: Feb 04 06:01:30.083: Decode routine not available, Printing Hex Dump
*spamApTask4: Feb 04 06:01:30.083: 00000000: 03 00 00 01 ....
*spamApTask4: Feb 04 06:01:30.083:
*spamApTask4: Feb 04 06:01:30.083: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 12
*spamApTask4: Feb 04 06:01:30.083: Vendor Identifier : 0x00409600
*spamApTask4: Feb 04 06:01:30.083:
IE : RAD_NAME_PAYLOAD
*spamApTask4: Feb 04 06:01:30.083: IE Length : 6
*spamApTask4: Feb 04 06:01:30.083: Rad Name :
*spamApTask4: Feb 04 06:01:30.083: CEO_AP
*spamApTask4: Feb 04 06:01:30.083: <<<< End of CAPWAP Packet >>>>
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Request from 10.192.200.93:26711
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 ApModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
*spamApTask4: Feb 04 06:01:30.083: apModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: apType = 26 apModel: AIR-CAP2602E-I-K9
*spamApTask4: Feb 04 06:01:30.083: apType: Ox1a bundleApImageVer: 8.0.110.0
*spamApTask4: Feb 04 06:01:30.083: version:8 release:0 maint:110 build:0
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93 port 26711
*spamApTask4: Feb 04 06:01:30.083: dc:a5:f4:8c:ff:30 Discovery Response sent to 10.192.200.93:26711
Please any help.

dear
yes the wlc 2504  is 8.0.110 but because its damaged i replaced it with new vWLC v 8.0.110.
also i can not put the LAP in flexconnect until its joint.

I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

It says that my DHCP has to be changed! How? to what?
It is 802.11g.express. but is set to default by the computer (Macbook Air).
The other is 802.11n. (express)
Extreme is 802.11.g. Is the Main Airport.
It is on ethernet & wep 128 security.

Hello i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to internet but another

hello
i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to internet but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem is remaining .is possible that to return to older version? if there is any solution share with me and i be very thankfulness of you.tanks again

It is not possible to downgrade to an earlier version.
Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update

Hello i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to inter net but another

hello
i have a an iPhone 5 .i updated it in the end of summer or begin of fall because i forget the number of version.it is important that i update my i Phone by itself not with iTune . after that my device can not join to wifi to inter net but another of app works properly and cellular can join to internet . i reset my i phone in the setting . general section but my problem is remaining . if there is any solution share with me and i be very thankfulness of you.tanks again

It is not possible to downgrade to an earlier version.
Have you tried the tips on this help page? iOS: Troubleshooting Wi-Fi networks and connections
And you dont need iTunes to update you're device. You can update it OTA in Settings > General > Software Update

Cisco 3502 AP will not join 4402

Have 5 WLC 4402's in my network. I upgraded one of them to 7.0.98.0 to test the new 3502 APs. When I go to join the new 3502 it will not join to the upgraded WLC. Keep in mind all WLC's are in the same mobility group. Does it matter that the rest of the controllers are not on 7.0 code?
thanks
izzy

AP3500 requires a minimum of 7.0.98.0. So my question is: When you console into the AP and reboot the AP (all in that order), can you please post everything?

I can not join any secure wifi network with my iphone5

I can not join any wifi network that requires a password including my home network. This is very frustrating

Hi Crystalmais,
This article contains troubleshooting for connecting to a Wi-Fi network:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Take care,
- Ari

I can not join the my home WIFI network. I have iPhone and iTouch connected as well as my windows laptop. I have trie power on rese, and network reset

I can not join the my home WIFI network. I have iPhone and iTouch connected as well as my windows laptop. I have trie power on rese, and network reset. What do I do next?

This is something else you can try.
Go to Settings>WiFi>Your Network Name (tap the blue arrow)>Forget this Network. Reboot your iPad, hold down on the sleep button at the top for a couple of seconds until the red slider appears, slide to shut down. Then press the sleep button again until the Apple logo appears and let go of the button and the iPad will restart. Try to join your network again.

My macbook pro, iphone, and ipad can not connect to the internet simultaneously. However my room mates computers that are not apple products are connected to the internet.

Occasionally my macbook, iphone, and ipad would not be connected to the internet at the same time. However, when they can connect, all three are connected at the same time. It is not my internet because my room mates computers are connected to the internet the whole time without any problems. When I can't connect, I can still see the network name on th wifi network search. However, when I click connect, the only message that pops up is can not join network.

Hi Lao3262,
Thanks for using Apple Support Communities. These articles have troubleshooting steps for issues with Wi-Fi on Macs and iOS devices respectively:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Cheers,
- Ari

Can not associate with the access point

Greetings!
I am just new here. I am trying to set-up a wireless connection from our linksys router. I recently purchased a linksys wireless internet receiver thru USB connection. Now, my problem is the pc that is supposed to receive a wireless connection is stating " can not associate with the access point". I am not too good about computers, that is why I am seeking you help.
I hope I can hear from you guys.
Thanks in advance.
Cheers!
Square

Lets start with the bad news, no wireless connection. Good news, fixable.
Make sure all your security settings on the usb adapter are correct. If router is set for wep set adapter to wep,and so on. Also check all your firewalls, in windows, and on any virus suites that you may have running. Try turning off all firewalls, other than router, and see if that helps. Also download the easy link advisor from the linksys home page. Make sure your ssid, and network names are set the same for router, and adapter.
Stlbluesfan30
Cisco Network Academy Student

Can not see all the clips in large Icon view in my bin

I arranged my clips in a bin in large Icon view but i can not see all the clips in the bin while in that mode. I see the clips when in list mode or when i drag them out of the bin into the main bin. As soon I drag them back in large icon view bin they do not show up, when going back in list view they are there.
Any idea
Also my daughter accidently pulled the electrical plug, which turned my external hard drive off. So the media was off line. I hit reconnect the clip but the clip does not show as connected in the bin it keeps the Media offline icon but putting the clip in the viewer or time line it plays it. So the clip is reconnected
hope anybody can help with those two issues thanks

Nick
thanks for your message it helped to show the clips. Here how I solved it. I put the clips i could not see in large Icon view, to the Project folder. Even in the project folder I was only seeing the clips with Thumbnail in list view. When i hit large Icon view the clips disappeared, and they could not have been lower down as i only have about 5 folders in the project. I then clicked arrange the clip by name and they showed up again. Like that i dragged the clip back in to its bin and it showed up. The reason for going back and forth I arranged the clips manually in the bin before and when hitting arrange by name it spread them to far apart and put the clips not in a sequence I liked.
for the second part I followed Neil's suggestion it worked.

Can not view all the thumbnails in version 9 adobe standard

Hello,
I recently installed adobe standard 9 running parallel with adobe standard 5.
My end user is claiming of the view setting for patient data. She can not scroll all the way to the bottom
as she could in adobe 5. She can see all the thumbnails minus the last row. I have changed the prefereces to show the same
as adobe 5. However I can not get the correct settting to make it right for her.
Any adivse or trouble shoot steps would be appreciated. Adobe said to update the product, I have done that last night.

How do I do that?
Date: Tue, 14 Dec 2010 10:10:01 -0700
From: [email protected]
To: [email address deleted by host]
Subject: Acrobat Windows Can not view all the thumbnails in version 9 adobe standard
Change the size of the thumbnails, change the size of the thumbnails window, or upgrade Acrobat X.
>

Can not use all the tools in my drawing markups any ideas on getting them to work?

Can not use all the tools in my drawing markups any ideas on getting them to work?

Hi tonys60181,
Could you please let me know what version of Adobe Acrobat are you using.
What all drawing tools are you unable to access?
Is this issue specific to one PDF file or all?
What exactly happens when you try to use any drawing markup?
Please let me know.
Regards,
Anubha

Slave instance can not synchronized with the master for a long time

Hi,
Slave instance can not synchronized with the master for a long time, and the gap of LSNs between slave and master are more and more larger. The transfer bytes per second between master and slave is 118MB/s , upper limit to the ethernet card. Why???
ENVIRONMENT:
1. A network program which we called mcdb is based on BDB 4.8.30. It is used to accept get/set requests and then query data from bdb or save data to bdb.
2. mcdb implements replication with bdb replication manager api. The default start replication policy is DB_REP_ELECTION, rep ack policy is DB_REPMGR_ACKS_ONE_PEER and rep priority is 100.
3. The bdb data files, bdb log files, region files and rep files are all in the same home directory.
4. There are two instances of the mcdb are separately on two standalone servers which has no other programs. These two instances are in one replication group which can elect a master automatically.
5. The master instance is online, which has lots of requests (get, set, delete).
ACTIONS:
1. Start two mcdb instances on two servers and the two instance make a replication group. Slave has already synchronized with the master.
2. Stop the slave for a long time (more than 20 hours).
3. Start the slave instance to synchronize data with master.
RESULT:
1. the gap of LSNs between slave and master are more and more larger.
2. db_stat of master and slave:
master db_stat:
467170     Number of PERM messages not acknowledged
9245     Number of messages queued due to network delay
172415     Number of messages discarded due to queue length
25880     Number of existing connections dropped
3407     Number of failed new connection attempts
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
DB_REPMGR site information:
10.67.15.146 (eid: 0, port: 30011)
Environment configured as a replication master
331726/3574994     Next LSN to be used
0/0     Not waiting for any missed log records
328872/466092     Maximum permanent LSN
0     Next page number expected
0     Not waiting for any missed pages
0     Number of duplicate master conditions originally detected at this site
2147M     Current environment ID (2147483647)
100     Current environment priority
49     Current generation number
50     Election generation number for the current or next election
2323     Number of duplicate log records received
0     Number of log records currently queued
6768     Maximum number of log records ever queued at once
55284     Total number of log records queued
120M     Number of log records received and appended to the log (120475988)
111     Number of log records missed and requested
2147M     Current master ID (2147483647)
2     Number of times the master has changed
0     Number of messages received with a bad generation number
8505306     Number of messages received and processed
12     Number of messages ignored due to pending recovery
471869     Number of failed message sends
12M     Number of messages sent (12959945)
0     Number of new site messages received
1     Number of environments believed to be in the replication group
990543     Transmission limited
0     Number of outdated conditions detected
0     Number of duplicate page records received
0     Number of page records received and added to databases
0     Number of page records missed and requested
Startup complete
6244678     Number of transactions applied
0     Number of startsync messages delayed
1     Number of elections held
1     Number of elections won
No election in progress
0.057097     Duration of last election (seconds)
8944103     Number of bulk buffer sends triggered by full buffer
0     Number of single records exceeding bulk buffer size
5273M     Number of records added to a bulk buffer (5273592170)
10M     Number of bulk buffers sent (10490865)
0     Number of re-request messages received
0     Number of request messages this client failed to process
0     Number of request messages received by this client
slave db_stat:
0     Number of PERM messages not acknowledged
0     Number of messages queued due to network delay
0     Number of messages discarded due to queue length
1454     Number of existing connections dropped
0     Number of failed new connection attempts
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
DB_REPMGR site information:
10.67.15.147 (eid: 0, port: 30011)
Environment configured as a replication client
329544/2916048     Next LSN expected
330433/2013808     LSN of first log record we have after missed log records
329543/5500501     Maximum permanent LSN
0     Next page number expected
0     Not waiting for any missed pages
0     Number of duplicate master conditions originally detected at this site
2147M     Current environment ID (2147483647)
100     Current environment priority
49     Current generation number
50     Election generation number for the current or next election
5256M     Number of duplicate log records received (5256599432)
3925284     Number of log records currently queued
3925285     Maximum number of log records ever queued at once
4880561     Total number of log records queued
3578038     Number of log records received and appended to the log
1912297     Number of log records missed and requested
0     Current master ID
1     Number of times the master has changed
0     Number of messages received with a bad generation number
12M     Number of messages received and processed (12980442)
2     Number of messages ignored due to pending recovery
0     Number of failed message sends
1912307     Number of messages sent
0     Number of new site messages received
0     Number of environments believed to be in the replication group
0     Transmission limited
0     Number of outdated conditions detected
0     Number of duplicate page records received
0     Number of page records received and added to databases
0     Number of page records missed and requested
Startup incomplete
110568     Number of transactions applied
80     Number of startsync messages delayed
0     Number of elections held
0     Number of elections won
No election in progress
0     Number of bulk buffer sends triggered by full buffer
0     Number of single records exceeding bulk buffer size
0     Number of records added to a bulk buffer
0     Number of bulk buffers sent
0     Number of re-request messages received
0     Number of request messages this client failed to process
0     Number of request messages received by this client
Edited by: 899585 on 2013-1-4 下午10:54
Edited by: 899585 on 2013-1-4 下午10:55

Hi,
Unfortunately, this issue is beyond the level of what is supported over the forum. Performance related issues are extremely complex and require an in-depth understanding of your environment and dedicated support. In a generic sense, you can look at this as a basic queueing problem. You have a server that went down and work is still coming in. When the server gets started it is possible that it may never catch up depending on new work coming in and the rate at processing the old work.
So what would you do in this case --- one thing would be to reduce the new work coming in. In HA terms this would be slowing the master down and you can increase DB_REP_ACK_TIMEOUT for this. Another thing you could do is add fresh servers to help reduce the workload. In HA terms, this would be the equivalent of restarting the client and give it a fresh look at everything. Another thing you could do is replan the system and load balance. In HA terms, it would mean something like take a hot backup of the master and reinit a client from scratch.
If you are interested in getting a dedicated support person working on this concern, please let me know and we can move forward down that path. Just respond to the thread with your email address and I will get in contact with you so we can pursue that approach.
thanks
mike

I have an iPhone 4 and my lock button is jammed and I also can not touch anything on the left side of my screen well as any pop ups from the phone itself, so i can not get past the set up stage in reset process...how can i fix it/can it be fixed?

I have an iPhone 4 and my lock button is jammed and I also can not touch anything on the left side of my screen well as any pop ups from the phone itself, so i can not get past the set up stage in reset process...how can i fix it/can it be fixed?

Make an appointment at the genius bar and get the phone replaced.

MY CISCO 6800 IA CAN NOT JOIN TO THE PARENT

Similar Messages

Maybe you are looking for