My computer crashed after an attempt to upgrade to Yosemite. I can't quit the installer and my MacBook keeps on restarting

I Have a 2008 Macbook Pro 15". It was running issue free until I upgraded to Yosemite. Now my logic board is fried and apple will not fix it. It started with mail accounts unable to send mail, just had to delete accounts and re- install to fix that. But, at the same time as the download, I started intermittently getting a green tint over the screen along with a snowy static like an old TV set. Fearing that my download was corrupt, I re- installed Yosemite over-writing the previous version . The green haze kept coming and going, but I also started getting strobe style white flashes in boxes in the 4 corners of my monitor. I had to do power button forced shutdowns because of pointer and keyboard function failure. Apple Genius desk told me it appeared to be a logic board failure but my computer was too old for them to work onand referred me to a Mac Specialist Center. I was told by both places that Apple installed defective logic boards back then due to changing solder formula. They extended product warranty by adding 1 yr but that still expired in 2012. I tried to post a warning on Mac Forums twice about Yosemite being a poison pill to certain platforms and my posts were pulled. The second attempt was responded to in my personal email account stating that if I don't stop posting derogatory comments, I will be blocked from forum. I am just trying to insert warnings in posts where I can. They haven't discovered that yet. Spread the word!

Similar Messages

Time Machine Locked after MacBook Air reformatted. My MacBook Air was overfull due to an Address book issue (duplication) so after many attempts to clear space, I ended up wiping out the system and reloading Lion.

Time Machine Locked after MacBook Air reformatted. My MacBook Air was overfull due to an Address book issue (duplication) so after many attempts to clear space, I ended up wiping out the system and reloading Lion. This resulted in the Time Machine thinking that it was now connected to a different computer. Apparently this diables the existing information.
Now I can see that the back-ups exist (back to Sept 2012) but they are greyed out, therefore unavailale to restore. Again, this seems like an issue that shouldn't be happening. The whole point of the Time Machine is to enable reinstatement of data after catastrophic failure. What if my computer actually had to be replaced due to a hardware issue? How would I beableto restore anything?
The path already (unsuccessfully) taken;
Open Library on the computer, Open Time Machine, Select Correct date, drill down to correct data you wish to restore, click "Restore".
This did not work because the correct date was greyed out. Restore key was greyed out.

Time Machine Locked after MacBook Air reformatted. My MacBook Air was overfull due to an Address book issue (duplication) so after many attempts to clear space, I ended up wiping out the system and reloading Lion. This resulted in the Time Machine thinking that it was now connected to a different computer. Apparently this diables the existing information.
Now I can see that the back-ups exist (back to Sept 2012) but they are greyed out, therefore unavailale to restore. Again, this seems like an issue that shouldn't be happening. The whole point of the Time Machine is to enable reinstatement of data after catastrophic failure. What if my computer actually had to be replaced due to a hardware issue? How would I beableto restore anything?
The path already (unsuccessfully) taken;
Open Library on the computer, Open Time Machine, Select Correct date, drill down to correct data you wish to restore, click "Restore".
This did not work because the correct date was greyed out. Restore key was greyed out.

Desktop computer crashes after sleep mode since upgrade to Snow Leopard

Since I upgraded my power Mac to Snow Leopard in December, I've had nothing but problems, all of which appear to stem from when it comes out of sleep mode. This computer and all applications were rock solid in Leopard! I also have a mac book running identical programs and that IS rock solid on Snow Leopard. I have a 2 x 2.8 GHz Quad Core Intel Xeon processor with 10 GB ram.
I did a complete re-install of SL and all programs as per the Apple instructions.
Basically, the computer crashes after sleep mode. I've tried all the fixes I've read on the net. Here is the report thread from the last crash. Does it mean anything or throw any light on the problem to anyone?
Thanks,
David Wright
Interval Since Last Panic Report: 14 sec
Panics Since Last Report: 1
Anonymous UUID: A8309844-77B4-45E9-AB36-6AF2850B84A0
Tue Jan 19 13:01:16 2010
panic(cpu 4 caller 0x2a7ac2): Kernel trap at 0x8722a3a1, type 14=page fault, registers:
CR0: 0x80010033, CR2: 0x00000000, CR3: 0x00100000, CR4: 0x00000660
EAX: 0x87e7a81c, EBX: 0x87e7a804, ECX: 0x10a2dd00, EDX: 0x00000000
CR2: 0x00000000, EBP: 0x87e7a7a8, ESI: 0x000001f8, EDI: 0xffc21000
EFL: 0x00010202, EIP: 0x8722a3a1, CS: 0x00000008, DS: 0x00000010
Error code: 0x00000000
Backtrace (CPU 4), Frame : Return Address (4 potential args on stack)
0x87e7a598 : 0x21b2bd (0x5cf868 0x87e7a5cc 0x223719 0x0)
0x87e7a5e8 : 0x2a7ac2 (0x591c30 0x8722a3a1 0xe 0x591dfa)
0x87e7a6c8 : 0x29d968 (0x87e7a6e0 0x246 0x87e7a7a8 0x8722a3a1)
0x87e7a6d8 : 0x8722a3a1 (0xe 0x48 0x10 0x290010)
0x87e7a7a8 : 0x8722f604 (0x10a2dd00 0x112e48c4 0x1 0x87e7a7e4)
0x87e7a838 : 0x8722ad60 (0x20d83400 0x10a2dd00 0x87e7a86f 0x0)
0x87e7a888 : 0x87306953 (0x10a2dd00 0x2 0x0 0xffffffff)
0x87e7a8e8 : 0x87789a40 (0x129f0d00 0xff91b80 0x1f8 0x2)
0x87e7a978 : 0x87788845 (0x6f40c004 0x12 0x7 0x2)
0x87e7aa48 : 0x87d92525 (0x159a3e00 0x30006 0x12493004 0x159a3e00)
0x87e7aa68 : 0x87d92413 (0x159a3e00 0x87d9e8a0 0x1 0x0)
0x87e7aa98 : 0x87d97df2 (0x159a3e00 0x12493000 0x5ac000 0x1)
0x87e7aad8 : 0x549661 (0x12493000 0x0 0x0 0x0)
0x87e7ab28 : 0x87d958d8 (0x10675f40 0x87d95df0 0x0 0x0)
0x87e7ab58 : 0x5638fc (0x12493000 0x87e7ab80 0x87e7ab84 0x87e7ab88)
0x87e7abd8 : 0x563c74 (0x11d8534c 0x12493000 0x20e35c90 0x0)
0x87e7ac28 : 0x564554 (0x12493000 0x3 0x87e7ac70 0x0)
0x87e7ad48 : 0x284797 (0x12493000 0x3 0x20e35c90 0x0)
0x87e7bdf8 : 0x21d65f (0x20e35c68 0x20c165a0 0x1fd2a0 0x5b17)
0x87e7be38 : 0x2107f7 (0x20e35c00 0x0 0x11434030 0x20e188f0)
Backtrace continues...
Kernel Extensions in backtrace (with dependencies):
com.RME.driver.FirefaceAudioDriver(2.64)@0x87785000->0x8778dfff
dependency: com.apple.iokit.IOAudioFamily(1.7.2fc1)@0x87d8d000
dependency: com.apple.iokit.IOFireWireFamily(4.1.7)@0x872ed000
com.apple.iokit.IOAudioFamily(1.7.2fc1)@0x87d8d000->0x87da4fff
dependency: com.apple.kext.OSvKernDSPLib(1.3)@0x87cf7000
com.apple.driver.AppleFWOHCI(4.4.0)@0x87221000->0x87246fff
dependency: com.apple.iokit.IOPCIFamily(2.6)@0x7dfa3000
dependency: com.apple.iokit.IOFireWireFamily(4.1.7)@0x872ed000
com.apple.iokit.IOFireWireFamily(4.1.7)@0x872ed000->0x8732ffff
BSD process name corresponding to current thread: QTKitServer
Mac OS version:
10C540
Kernel version:
Darwin Kernel Version 10.2.0: Tue Nov 3 10:37:10 PST 2009; root:xnu-1486.2.11~1/RELEASE_I386
System model name: MacPro3,1 (Mac-F42C88C8)
System uptime in nanoseconds: 82873577512931
unloaded kexts:
com.apple.driver.AudioAUUC 1.0 (addr 0x878f1000, size 0x16384) - last unloaded 82669937654216
loaded kexts:
com.RME.driver.FirefaceAudioDriver 2.64 - last loaded 82552224025300
com.paceap.kext.pacesupport.snowleopard 5.7.2
tc.tctechnologies.driver.AlesisFirewire 6300
com.apple.filesystems.autofs 2.1.0
com.apple.driver.AppleHWSensor 1.9.2d0
com.apple.DontSteal_Mac_OSX 7.0.0
com.apple.iokit.CHUDUtils 201
com.apple.driver.AppleUpstreamUserClient 3.1.0
com.apple.iokit.CHUDProf 214
com.apple.kext.ATIFramebuffer 6.0.6
com.apple.driver.AppleIntelPenrynProfile 17
com.apple.ATIRadeonX2000 6.0.6
com.apple.driver.AudioIPCDriver 1.1.2
com.apple.driver.AppleHDA 1.7.9a4
com.apple.driver.AppleIntel8254XEthernet 2.1.1b7
com.apple.driver.AirPortBrcm43xx 421.91.26
com.apple.driver.AppleUSBDisplays 2.2
com.apple.driver.AppleMCEDriver 1.1.9
com.apple.driver.Apple_iSight 4.0.1
com.apple.driver.ACPISMCPlatformPlugin 4.0.1d0
com.apple.driver.AppleLPC 1.4.9
com.apple.iokit.SCSITaskUserClient 2.6.0
com.apple.iokit.IOAHCIBlockStorage 1.6.0
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.driver.AppleUSBHub 3.8.4
com.apple.driver.AppleFWOHCI 4.4.0
com.apple.driver.AppleUSBEHCI 3.7.5
com.apple.driver.AppleAHCIPort 2.0.1
com.apple.driver.AppleIntelPIIXATA 2.5.0
com.apple.driver.AppleEFINVRAM 1.3.0
com.apple.driver.AppleUSBUHCI 3.7.5
com.apple.driver.AppleACPIButtons 1.3
com.apple.driver.AppleRTC 1.3
com.apple.driver.AppleHPET 1.4
com.apple.driver.AppleSMBIOS 1.4
com.apple.driver.AppleACPIEC 1.3
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 96.0.0
com.apple.security.sandbox 0
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.1.11
com.apple.driver.AppleIntelCPUPowerManagement 96.0.0
com.apple.driver.AppleProfileReadCounterAction 17
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.iokit.IOSurface 73.0
com.apple.iokit.IOBluetoothSerialManager 2.2.4f3
com.apple.iokit.IOSerialFamily 10.0.3
com.apple.iokit.CHUDKernLib 207
com.apple.driver.DspFuncLib 1.7.9a4
com.apple.iokit.IONDRVSupport 2.0
com.apple.kext.ATI2600Controller 6.0.6
com.apple.kext.ATISupport 6.0.6
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.iokit.IO80211Family 310.6
com.apple.iokit.IONetworkingFamily 1.9
com.apple.iokit.AppleProfileFamily 41
com.apple.driver.AppleHDAController 1.7.9a4
com.apple.iokit.IOGraphicsFamily 2.0
com.apple.iokit.IOHDAFamily 1.7.9a4
com.apple.iokit.IOAudioFamily 1.7.2fc1
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleSMC 3.0.1d2
com.apple.driver.IOPlatformPluginFamily 4.0.1d0
com.apple.driver.CSRUSBBluetoothHCIController 2.2.4f3
com.apple.driver.AppleUSBBluetoothHCIController 2.2.4f3
com.apple.iokit.IOBluetoothFamily 2.2.4f3
com.apple.driver.AppleUSBHIDMouse 1.4.0d7
com.apple.driver.AppleHIDMouse 1.4.0d7
com.apple.driver.AppleUSBHIDKeyboard 1.2.0a3
com.apple.iokit.IOUSBHIDDriver 3.8.4
com.apple.driver.AppleHIDKeyboard 1.2.0a3
com.apple.driver.AppleUSBMergeNub 3.8.5
com.apple.driver.AppleUSBComposite 3.7.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.6.0
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IOATAPIProtocolTransport 2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 2.6.0
com.apple.iokit.IOUSBUserClient 3.8.5
com.apple.iokit.IOFireWireFamily 4.1.7
com.apple.iokit.IOAHCIFamily 2.0.2
com.apple.iokit.IOATAFamily 2.5.0
com.apple.iokit.IOUSBFamily 3.8.5
com.apple.driver.AppleEFIRuntime 1.3.0
com.apple.iokit.IOHIDFamily 1.6.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.TMSafetyNet 6
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 281
com.apple.iokit.IOStorageFamily 1.6
com.apple.driver.AppleACPIPlatform 1.3
com.apple.iokit.IOPCIFamily 2.6
com.apple.iokit.IOACPIFamily 1.3.0
Model: MacPro3,1, BootROM MP31.006C.B05, 8 processors, Quad-Core Intel Xeon, 2.8 GHz, 10 GB, SMC 1.25f4
Graphics: ATI Radeon HD 2600 XT, ATI Radeon HD 2600, PCIe, 256 MB
Memory Module: global_name
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x88), Broadcom BCM43xx 1.0 (5.10.91.26)
Bluetooth: Version 2.2.4f3, 2 service, 1 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en2
PCI Card: ATI Radeon HD 2600, Display, Slot-1
Serial ATA Device: WDC WD10EADS-00P8B0, 931.51 GB
Serial ATA Device: ST3500630AS, 465.76 GB
Serial ATA Device: ST3500630AS, 465.76 GB
Serial ATA Device: WDC WD10EADS-00P8B0, 931.51 GB
Parallel ATA Device: OPTIARC DVD RW AD-7170A
USB Device: Hub, 0x05ac (Apple Inc.), 0x912f, 0xfd500000
USB Device: Apple Cinema HD Display, 0x05ac (Apple Inc.), 0x9221, 0xfd520000
USB Device: USB2.0 Hub, 0x05e3 (Genesys Logic, Inc.), 0x0608, 0xfd300000
USB Device: USB2.0 Hub, 0x05e3 (Genesys Logic, Inc.), 0x0608, 0xfd340000
USB Device: ProtectExecuter, 0x0819, 0x0101, 0xfd344000
USB Device: iLok, 0x088e, 0x5036, 0xfd343000
USB Device: MS-20 Controller, 0x0944, 0x0101, 0xfd341000
USB Device: Keyboard Hub, 0x05ac (Apple Inc.), 0x1006, 0xfd310000
USB Device: Apple Optical USB Mouse, 0x05ac (Apple Inc.), 0x0304, 0xfd313000
USB Device: Apple Keyboard, 0x05ac (Apple Inc.), 0x0221, 0xfd312000
USB Device: USB2.0 Printer (Hi-speed), 0x04b8 (Seiko Epson Corp.), 0x0007, 0xfd200000
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8206, 0x5d200000
FireWire Device: Vendor 0xA35 Device 0x101800, 0xA35, Up to 400 Mb/sec
FireWire Device: built-in_hub, Up to 800 Mb/sec
FireWire Device: iSight, Apple Computer, Inc., Up to 200 Mb/sec
FireWire Device: unknown_device, Unknown

davidadmusic wrote:
The problem has been identified as the RME fireface400 audio driver. I've spent some considerable time experimenting to identify the culprit. It's clear that this is what is causing all my problems since Snow Leopard. Whether it's exclusively the drivers fault or partly also due to a conflict with apple SL, I don't know, but I have crash reports if apple want to see them.
From your first post, it appears you are using Fireface audio driver version 2.64. RME released a new Snow Leopard compatible driver (version 2.65) last December. It is available at RME: Downloads. (There is also a firmware updater for the Fireface 400 there, which you might want to check out.)
It isn't at all unusual for a new OS version to require new drivers for third party hardware. References to this can be found all over the web, in "read me" files & other documentation, etc. -- it doesn't just apply to OS X but to Windows & other OS's as well. (One of the biggest problems with Vista was poor third party driver support.) In fact, the X-Lab "Resolving Kernel Panics" article specifically cautions users to make sure all such drivers are current. See section 6.1 of that article for more details.
I don't know if you missed all this somehow, but if you haven't already downloaded & installed the new RME driver (& possibly the firmware update as well), then do so now. While you are at it, check for other similar updates for any other third party hardware devices you use, using the info in section 6.1 of the X-Lab article as a guide.
Hopefully, this will resolve your issue, which (as already mentioned) is kernel panics, not crashes. If you still have problems, post more about them, being mindful of the difference between application crashes & kernel panics. Because they are fundamentally different, they have different cures, so we will need to know which type they are to offer effective help.

HT201413 I have a Windows XP Home Edition computer. I recently attempted to upgrade iTunes to v10.7. It loaded and installed OK, but now it won't run. When I try to launch it, it gets aborted by the windows Data Execution Prevention software. Any ide

I have a Windows XP Home Edition computer. I recently attempted to upgrade iTunes to v10.7. It loaded and installed OK, but now it won't run. When I try to launch it, it gets aborted by the windows Data Execution Prevention software. Any ideas?

Yes, this did solve the problem. But I had some trouble updating QuickTime. It failed, with the installer complaining that it did not have the required permissions to install the files it needed in the program directory. I got it to work by telling it to install the files to another directory. All seems well now - Thanks!

Computer Crashes after 1.1.1 update??

Has anyones computer crashed after update???
heres wat happen to me!
First i got errors -48. Called Apple had to create new user account to on my computer to work around it. then logged back in to my user account and got error -50 that said unable to sync!
I go to restart my computer hoping that would fix it. It wont restart!!! I push the power button and it makes the little sound and u hear the disc drive then the screen turns gray and stays gray and doesnt do anything else!!!
Whats going on!!!

Well the first thing I thought of was device driver problems, and there is a lot of that being reported here, although I've never seen it reported on a MAC system. I would still say though that it has something to do with your system setup, exactly what unknown, you'd have to troubleshoot that yourself, sorry, but it could be lots of things and you would know your system better than anyone else. I can tell you one thing though, I use my iPhone on my MAC, Vista 32b, and XP PRO with no problems at all. So it's got to be something inherent in your system. USB ports can be flakey on MAC's as well as windows systems, so the first thing I would do is unplug all existing USB devices, accept keyboard/mouse, and try to proceed from there.
I would also try to ignore the idiots that only want to post things like OOOooopppsss.
Message was edited by: QuickDraw

HT1420 I recently upgraded to a macbook pro after my old pc laptop crashed, is there a way to ensure that I can get all the songs off my iPhone when I sync?

I recently upgraded to a macbook pro after my old pc laptop crashed, is there a way to ensure that I can get all the songs off my iPhone when I sync?

There's some third party applications available. The following article is pretty old (2008) so it would be best to reality-check the capabilities and availability of the various listed items prior to opting for a particular product:
http://www.ilounge.com/index.php/articles/comments/copying-music-from-ipod-to-co mputer/P2

Hello Everyone. I have an older version of aperture, aperture 2, that I wanted to install on my MAC. I attempted the installation, and during the install there was a check to see if my computer was capable of installing the software, which it was.

Hello Everyone. I have an older version of aperture, aperture 2, that I wanted to install on my MAC. I attempted the installation, and during the install there was a check to see if my computer was capable of installing the software, which it was. After the install completed I tried running the software, and I got a message telling me I can't run this version with my operating system. Does anyone know why I can't run the aperture software, and why I was allowed to install it without some notification.

Hello Everyone. I have an older version of aperture, aperture 2, that I wanted to install on my MAC. I attempted the installation, and during the install there was a check to see if my computer was capable of installing the software, which it was. After the install completed I tried running the software, and I got a message telling me I can't run this version with my operating system. Does anyone know why I can't run the aperture software, and why I was allowed to install it without some notification.

After I upgraded to Yosemite iphoto can't recognize my backup CDs which were created in iLife09. Ihave the original applications install disk and my old hard drive(I upgraded to SSD). How do I get a n iphoto back to read by old CDs?

After I upgraded to Yosemite,iPhoto can't recognize my backup CDs created in iLife 09. The applications install disk won't install iphoto because iphoto 9.5 is already installed..I updated to a SSD and have the original Hard Drive with an updated iphoto which recognized the older CDs(thanks to iphoto expander). I thought that the iphoto that transferred with the new hard drive was the same as what was on the old one. I guess it wasn't. I really need to access my backups. HELP

Later version of iPhoto write to the library on opening, and so cannot open libraries on optical media, as that cannot be written to. Further, optical media is going e way of the floppy disk. Therefore, you need to use a different form of archiving and back up going forward.
To allow iPhoto to open these libraries you need to copy them to your Mac or an attached external disk.
To merge them into an existing Library will require that you use either Aperture (if you have it) or iPhoto Library Manager.

After upgrading to Yosemite, I can't print on Okidata c5150n

After upgrading to Yosemite, I can't print on Okidata c5150n. Oki is of no help. I am connected by ethernet.

For those trying to use an Oki C5150n printer with OS X Yosemite, the fix is now available. One must use the driver for the Oki C5800Ldn printer from the Oki support page because the Yosemite compatible driver does not yet appear on the page for the C5150n. However at Oki customer support's direction I have loaded and used this driver, and so far it is working just fine. To download the driver use the link at the end of this comment and navigate to the OS.X.10 download option under "find a driver". Be advised that one must remove the Oki printer from the list in the "Printers and Scanners" system preference window and then re-create it de novo after installing the new driver as the old one will not work. Unfortunately this means that any documents left hanging in the print queue prior to installation of the new driver will be lost.
http://my.okidata.com/pp-C5800Ldn.nsf?opendatabase
Good luck to all!

Adding reminders to my calendar items is no longer an option after the software upgrade. I also can't get to day and week view, only month view. What's a possible solution?

Adding reminders to my calendar items is no longer an option after the software upgrade. I also can't get to day and week view, only month view. What's a possible solution? I'm using Andriod version 4.4.2 with kernal 3.4.0.

@MaloneTP
Thanks for keeping me updated! Do you see the screen options displayed in the following link: http://bit.ly/T2koBL for changing the calendar view options in Kies Air? Also, let me know if you're able to add a Reminder by following these steps: http://bit.ly/T2l9dY. Keep me posted. Thanks!
AnthonyTa_VZW
Follow us on Twitter @VZWSupport

My computer crashed with all my itunes files. I was able to get some off and transfer them to another computer. I am afraid to sync my ipod to the new computer becaused I do not want to loose all of my playlists and other music. Will this happen?

My computer crashed with all my itunes files. I was able to get some off and transfer them to another computer. I am afraid to sync my ipod to the new computer becaused I do not want to loose all of my playlists and other music. Will this happen?

To import music into your iTunes library on the computer go to iTunes>Help>iTunes Help>Add items to iTunes and follow the instructions
Delete the "songs" that do not play in your iTunes library and reimport them.

Nokia Lumia 928 apparently died after an attempted Windows 8.1 update. Replacement phone arrived the next day. How can I restore my contacts, photos, etc.? Backup assistant is no help and I don't know how to access the Cloud.

Nokia Lumia 928 apparently died after an attempted Windows 8.1 update. Replacement phone arrived the next day. How can I restore my contacts, photos, etc.? Backup assistant is no help and I don't know how to access the Cloud.

Did you have the phone set to backup things to the One Drive on Microsoft servers?

Hi! I bought a song on itunes, and now it won't play on my computer or iPod. Itunes on my computer keeps telling me that I'm not authorized to play the song on my computer, even after reauthorizing it. Is there anything I can do to play the song?

Hi! I bought a song on itunes, and now it won't play on my computer or iPod. Itunes on my computer keeps telling me that I'm not authorized to play the song on my computer, even after reauthorizing it. Is there anything I can do to play the song?

Hello
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iTunes repeatedly prompts to authorize computer to play iTunes Store purchases
http://support.apple.com/kb/ts1389
Best of luck,
Mario

I upgraded to Yosemite 10.10.2 from the last cat. Now my QuarkXPress 9.5 crashes when I open/create a document

I upgraded to Yosemite 10.10.2 from the last cat. Now my QuarkXPress 9.5 crashes when I open/create a document

Check for compatibility: See App Compatibility Table - RoaringApps.

HT6114 I have upgraded to OS X Mavericks and my MacBook keeps crashing and my numbers and pages programs will not open as they are being updated continuously.

I have upgraded to OS X Mavericks and my MacBook keeps crashing and my numbers and pages programs will not open as they are being updated continuously

The next time the crash happens, note the date and time the problem occurred, then go to Applications/Utilities/Console and copy the log starting at the time of the crash. Paste the log in a reply. Please do not use a screen shot as they can be hard to read. If there are repeated runs of the same messages, please post only one run. Be selective about what you post and don’t post huge amounts. Make sure there is no personal data visible. Information learned from Linc Davis.

My computer crashed after an attempt to upgrade to Yosemite. I can't quit the installer and my MacBook keeps on restarting

Similar Messages

Maybe you are looking for