My computer has no sound
hi my macbook pro has lost sound - have done all the basic thngs to fix (pram restart) and there is there nothing jammed in the jack. Any ideas?
Go step by step and test.
1. System Preference > Sound > Output > Internal Speakers
Highlight Internal Speakers.
Make sure that Mute is not enabled.
2.Plug in and remove the headphone.
If you see red light in the headphone port, plug the headphone
in and out of the port 5 or 6 times to flip the microswitch inside.
Sound output may be stuck in the digital mode.
3. Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
4. Applications > Utilities > Audio MIDI Setup
Audio Devices window
Side Bar
Click the Built-in Output.
Under Mute any of the boxes checked? If so, uncheck it.
Similar Messages
-
My computer has no sound :( help?
I really need some help. My computer has no sound at all. Windows media player, youtube, there just doesn't seem to be any sound. (my volume is not on mute) I also checked that my sound driver is installed and updated but still no audio Thanks in advance!
This question was solved.
View Solution.Hi,
It might be worth resetting the bios defaults as follows.
Shut down the PC. Tap away at the esc key as soon as you start the PC to enter the Start-up Menu and then select the Bios menu ( usually f10 ). Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter. Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
HP Envy 23 touchsmart windows 8.1 computer has no sound only with headset
Computer had working sound 2 days ago. But now it will only work with a headset. I have checked and tested and says every thing is working fine. I am at a loss.
Thanks,Hello retired_gramma,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that a few days ago you had sound and now you only have sound when you plug in your headset and that you are running Windows 8.1. I am providing you with an HP Support document: Using Microsoft System Restore (Windows 8), which will walk you through restoring your computer back to before this happened. As you stated it is only 2 days I would go back a week. This will not affect your personal files, but it will affect any applications or settings that have been installed or changed in the past week.
Please re-post if you require additional assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
Computer: HP Pavilion g6-1d28dx
System: Windows 7 - 64 bit
Error Message: "Driver not installed properly" I did not accept any drivers to install, and it did not specify what it was trying to install.
I made no changes to the system that I know of..
And now, my sound does not work. I tried through the internet and Windows Media Player. WMP gives me an error message when I try to play music, and will not play. The error message states "Windows Media Player encountered a problem while playing the file." When I click the "web help" button from WMP it tells me to update my drivers, but my computer says all sound based drivers are up to date.
Help?Download & Save the latest IDT Audio driver. In Control Panel, Programs & Features uninstall the IDT software, restart the laptop and use the downloaded file to reinstall.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5242...
```````````````````````````````````````
If still no sound,try a hard reset.Disconnect all external devices first.
1-remove power cord and battery
2-press power button for 30 seconds
3-reinstall only power cord for first startup.
4-power on
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
My Mac SUDDENLY has no sound - what gives?
Hi John,
First try a PRAM reset, CMD+Option+p+r...
http://docs.info.apple.com/article.html?artnum=2238
If that doesn't cure it, Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there, some things will change it for their own use, then not set it back. -
Downloaded ver. 8.1. Now my computer has no sound.
After downloading ver. 8.1, I have no sound at all thru my computer. No changes in volume settings, mutes are off, no changes in default sound card. Visually, iTunes is 'playing the song'. This is true whether it is an MP3 on computer or a CD in D drive. Help!
I'm haveing exactly the same problem on my G4 Quicksilver. System audio works, but no sound from itunes. I cannot play any of my music.
-
My computer has lost sound on utube but still plays on itunes
Hi, I no longer have sound on utube or news channels but do have sound on itunes.
ideas?
GarrettHmmm, looks serious from here...
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive & clear caches.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
After reboot, do we still get those 2 errors? -
what do you do when you download a show and it has no sound? ( the volume is up on itunes and my computer)
That's what iTunes -> Preferences -> Playback -> Sound Check does - equalizes the volume across tracks to provide a more-even playback.
-
My iphone 5 doesn't sync with itunes on my pc. it says this computer has previously been synced to another io6 device or iphone? please help what to do?
The error message you're seeing is likely the other way around -- i.e. something like "This iPhone has previously been synced with a different computer". There's no problem syncing multiple iOS devices to the same computer.
However, the reverse is not true for the iPhone -- you cannot connect an iPhone to another computer without it being erased, even if you manually manage music and video. So, it sounds like you've been syncing your iPhone to a different computer?
Also, 5.1 (not 5.0.1) is the latest iOS. -
I purchased a movie from iTunes and when i try to play it on my mac or iphone its just black and has no sound...
help please!Are you going to Movies - Purchased or Computers - Movies ?
If you go to iTunes Store on your computer - Quicklinks - Purchased. Is it showing up there?
Is this a purchase or a rental? -
The problem that have started when I was going to sync my iPhone 4 with current iTunes running on 64bit Windows 7.
I started iTunes and plugged in my iPhone.
All looked good and the iPhone came up as the device as it should have.
Next I wanted to transfer purchases prior to syncing so I started the Transfer Purchases process.
iTunes stopped working during the Transfer Purchases process
Now when I plug in my iPhone iTunes takes me to the “setup your iPhone” screen and displays “This computer has previously been synced with an iPhone or another iOS device” and only allows me to restore and old backup or setup as new.
Obviously some files were not closed properly when iTunes crashed during the transfer purchases process, how can I cleanup iTunes so that it will allow me to backup and sync my phone.
I am a software developer and am sure that a fix is not in the menu options What I am saying is that I can easily remove or edit corrupt files to get it working.
Thanks, MikeThe error message you're seeing is likely the other way around -- i.e. something like "This iPhone has previously been synced with a different computer". There's no problem syncing multiple iOS devices to the same computer.
However, the reverse is not true for the iPhone -- you cannot connect an iPhone to another computer without it being erased, even if you manually manage music and video. So, it sounds like you've been syncing your iPhone to a different computer?
Also, 5.1 (not 5.0.1) is the latest iOS. -
My computer has been acting weird lately. Shuts itself off, the mouse goes off in all directions, does not go into sleep mode sometimes, instead shows a gray screen with word definitions in large 3" letters that continuosly flows across the screen. Do I have a virus?
Doesn't really sound like a virus.
See if the Disk is issuing any S.M.A.R.T errors in Disk Utility...
http://support.apple.com/kb/PH7029
How many of these you can answer...
Open Activity Monitor in Applications>Utilities, select All Processes & sort on CPU%, any indications there?
How much RAM & free space do you have also, click on the Memory & Disk Usage Tabs.
Open Console in Utilities & see if there are any clues or repeating messages when this happens.
In the Memory tab, are there a lot of Pageouts? -
My 2006 Mac with Intel that is running on OSX 10.6.8 suddenly has no sound
My computer has been acting a little erratic for close to a month now, but I thought it was a browser issue. Ever since I uninstalled Google Chrome and Firefox, then downloaded Safari, things are not loading as quickly as they should, I try to download newer versions of Firefox and/or GoogleChrome, and, when I do, it will not download completely. The download will begin, then stop, and I'll get this message on the screen saying "Plug-in Failure". I installed MacKeeper, and, it seemed to be helping, a little, but, when I read what people had said about it in here, I immediately uninstalled it. Yesterday evening, prior to uninstalling MacKeeper, I lost all sound on my computer. It had been fine, and then suddenly, it was just gone. I uninstalled MacKeeper, tried changing system preferences, tried all kinds of things, and still no sound. That, andI'm still unable to download other web browsers. Any advice on the matter would be greatly appreciated. Thanks!
How large is your HD & how much space do you have left?
Regarding your sound:
Repair permissions & restart.
Check your settings in the Audio Midi app which is located in the Utilities folder.
http://support.apple.com/kb/TS1574 Troubleshooting issues with no audio from built-in speakers on Macs
Trick/Tip: Open up GarageBand if installed then, open a program (optional).
Quit out of the GarageBand app.
=====================
Repairing the mysteriously muted Mac
The background on the issue is that there’s a small sensor switch inside the headphone port. When you insert a headphone jack, the sensor understands what's what and changes the sound output setting to Headphones. If you insert a jack for digital audio output, the device changes to Digital Out. When you remove the jack completely, it should read Internal Speakers.
The spirits tell me that there’s a very good chance that you recently had something jacked into this port—a set of headphones or a cable leading to powered speakers, for example. When you removed the jack, something in the port prevented the sensor from tripping correctly. That’s why you see Digital Out instead of internal Speakers.
The solution is to force the sensor to do its job. The safest way to do that is to simply run a jack in and out of the port a few times. Much of the time, this takes care of the problem by correctly tripping the sensor. If that doesn’t work, there may be gunk in the port. Before turning to more invasive techniques, get a can of compressed air, attach the small tube that fits the nozzle, and blast a few shots of air into the port. With any luck, that should dislodge the gunk and the port will operate as it should.
If that doesn’t work, find a foam-tipped swab that fits (electronics shops generally carry them), dip it in rubbing alcohol, and gently insert it into the headphone port in an attempt to wipe away any stubborn gunk. I recommend foam rather than cotton swabs because the cotton variety might leave threads behind. (This same technique works well with misbehaving headphone ports on devices such as iOS devices.)
It's possible that gunk has nothing to do with it. Rather, it may be that the switch just needs a subtle nudge. If a jack or swab doesn't work, I've heard of people successfully resetting it with a deft poke of a toothpick.
http://www.macworld.com/article/2031146/repairing-the-mysteriously-muted-mac.htm l -
Quicktime Restarts Computer, Has NO Audio
Quicktime Restarts Computer, Has NO Audio
Quicktime 7.7.2 Restarts Computer.
Summary:
1. Change the setting so the Computer does NOT Restart on Error.
2. Update the Video Driver.
See article on how to change the setting so the computer will NOT Restart on Error: https://discussions.apple.com/thread/743448?start=0&tstart=0
• Changed the Setting so the Computer will NOT Restart on Error.
• Updated ATI Video Driver from the Internet ( Computer > Properties > … > Device Manager, right Click on Video Driver and click Update Driver.
Now Quicktime did NOT Crash but still had NO Audio (See below).
Quicktime 7.7.2 has NO Audio.
Summary:
1. Install an older version of Quicktime (Ex. 7.6.5)
• I Updated the SoundBlaster Audigy Driver from the Internet (Still NO Audio when running Quicktime).
• Now that the Drivers were Updated, I Uninstalled and then re-installed Quicktime to see if it would make a difference (Still NO Audio when running Quicktime).
• Trying something else - I installed an older Version of Quicktime ( I used 7.6.5).
Now Audio worked when using Quicktime.
Computer Specs:
• AMD 3000+
• 3GB RAM.
• Windows XP Service Pack 3.
• ATI Video Card.
• SoundBlaster Audigy Sound Card.
Extra Notes: Even with my Windows 7 Computer - I only have 7.6.7 - it also works correctly - with audio.Qualcomm Pure Voice is still an export option in version 7.3 (as it has been in every version).
It fails to play in 7.3 as others have noticed. I didn't catch it in my beta tests of this version and expect it to be fixed with an updated version.
I just tested exports using that codec and they do play the audio. Only a few Pure Voice audio tracks I have on my machine fail. All use 22.050 Hz at mono settings.
A bug. -
Hi All
I formatted and installed Win8.1 (64-bit) recently on my PC but have constantly had BSOD with faults like:
Log Name: System
Source: Microsoft-Windows-WER-SystemErrorReporting
Date: 27/11/2014 09:40:21
Event ID: 1001
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: PC1
Description:
The computer has rebooted from a bugcheck. The bugcheck was: 0x0000003b (0x00000000c0000005, 0xfffff8025714c975, 0xffffd001186a85f0, 0x0000000000000000). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 112714-32125-01.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" />
<EventID Qualifiers="16384">1001</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2014-11-27T09:40:21.000000000Z" />
<EventRecordID>8488</EventRecordID>
<Correlation />
<Execution ProcessID="0" ThreadID="0" />
<Channel>System</Channel>
<Computer>PC1</Computer>
<Security />
</System>
<EventData>
<Data Name="param1">0x0000003b (0x00000000c0000005, 0xfffff8025714c975, 0xffffd001186a85f0, 0x0000000000000000)</Data>
<Data Name="param2">C:\Windows\MEMORY.DMP</Data>
<Data Name="param3">112714-32125-01</Data>
</EventData>
</Event>
I've had others but this is the most recent. I ran the Nvidia scanner and loaded the video drivers it recommends (340.52). I've got two GeForce 8800GTX cards connected with SLI cable. I've tried turning SLI off as well. I also removed and re-seated the cards.
I also just replaced the RAM with another 4GB brand new from a supplier (240pin DDR2 DIMM UNBUFF.PC2 - 6400 CL6).
It crashed about once a day, totally randomly, sometimes when idle.
I zipped a copy of the DUMP file and MSINFO32 file to my OneDrive but I don't know if I need / how to share it (please advise if necessary).
I would be very grateful for a solution.
Regards
MarkOk, here is what I think. The MEMORY.DMP you provided was older and basically less helpful than what was recorded in the MSIinfo file. You are on the right track in your thinking that the crashes are related to
GeForce 8800GTX cards, so I am going to suggest an uninstall and "clean" reinstall of the current driver.
If no joy, try an older driver.
btw, apologies for the voluminous post...
25/11/2014 12:31 Windows Error Reporting Fault bucket
AV_nvlddmkm!CNvLChannelNonLegacy::pipelineGPFifoBlit, type 0
Event Name:
BlueScreen
Response:
http://wer.microsoft.com/responses/resredir.aspx?sid=10&Bucket=AV_nvlddmkm!CNvLChannelNonLegacy::pipelineGPFifoBlit&State=1&ID=e2e8a1cf-86d8-4a37-806c-7d971c8a16d6
Cab Id: e2e8a1cf-86d8-4a37-806c-7d971c8a16d6

Problem
signature:
P1: d1
P2: fffffffffffffff1
P3: 2
P4: 1
P5: fffff801ca3d1440
P6: 6_3_9600
P7: 0_0
P8:
768_1
P9: 
P10: 

Attached files:
C:\Windows\Minidump\112514-33906-01.dmp
C:\Users\Mark\AppData\Local\Temp\WER-95625-0.sysdata.xml
C:\Windows\MEMORY.DMP
C:\Users\Mark\AppData\Local\Temp\WERCED4.tmp.WERInternalMetadata.xml

These
files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportArchive\Kernel_d1_a7d30b578e595ab79ff817b74f971d37c1e8e_00000000_cab_10a9e058

Analysis symbol: 
Rechecking
for solution: 0
Report ID: 112514-33906-01
Report Status: 0
Hashed bucket:
24/11/2014 17:22 Windows Error Reporting Fault bucket AV_nvlddmkm!vblankCallback, type 0
Event Name: BlueScreen
Response:
http://wer.microsoft.com/responses/resredir.aspx?sid=10&Bucket=AV_nvlddmkm!vblankCallback&State=1&ID=f616ba0f-2c01-41f5-bfc4-82489997cecc
Cab Id: f616ba0f-2c01-41f5-bfc4-82489997cecc

Problem
signature:
P1: d1
P2: 5e
P3: 6
P4: 1
P5: fffff80075721912
P6: 6_3_9600
P7: 0_0
P8:
768_1
P9: 
P10: 

Attached files:
C:\Windows\Minidump\112314-37250-01.dmp
C:\Users\Mark\AppData\Local\Temp\WER-86718-0.sysdata.xml
C:\Windows\MEMORY.DMP
C:\Users\Mark\AppData\Local\Temp\WER684A.tmp.WERInternalMetadata.xml

These
files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportArchive\Kernel_d1_79675c223622dece3b44f5ae297e5b3f6af5349_00000000_cab_04d8b9c0

Analysis symbol: 
Rechecking
for solution: 0
Report ID: 112314-37250-01
Report Status: 0
Hashed bucket:
23/11/2014 18:03 Windows Error Reporting Fault bucket , type 0
Event Name:
BlueScreen
Response: Not available
Cab Id: 0

Problem signature:
P1: d1
P2: 5e
P3:
6
P4: 1
P5: fffff80075721912
P6: 6_3_9600
P7: 0_0
P8: 768_1
P9: 
P10: 

Attached
files:
C:\Windows\Minidump\112314-37250-01.dmp
C:\Users\Mark\AppData\Local\Temp\WER-86718-0.sysdata.xml
C:\Windows\MEMORY.DMP
C:\Users\Mark\AppData\Local\Temp\WER684A.tmp.WERInternalMetadata.xml

These
files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\Kernel_d1_79675c223622dece3b44f5ae297e5b3f6af5349_00000000_cab_0d89e73e

Analysis symbol: 
Rechecking
for solution: 0
Report ID: 112314-37250-01
Report Status: 100
Hashed bucket:
24/11/2014 17:22 Windows Error Reporting Fault bucket -421640870, type 5
Event Name:
PnPDeviceProblemCode
Response: Not available
Cab Id: 0

Problem signature:
P1: x64
P2:
PCI\VEN_10DE&DEV_0191&SUBSYS_22501682&REV_A2
P3: {4d36e968-e325-11ce-bfc1-08002be10318}
P4: 0000001F
P5: BasicDisplay.sys
P6: 6.3.9600.16384
P7:
08-22-2013
P8: 
P9: 
P10: 

Attached files:
C:\Windows\Temp\DMID706.tmp.log.xml
C:\Windows\Temp\LOGD727.tmp
C:\Windows\Inf\display.inf

These
files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\NonCritical_x64_24eb8c9ed87f37eac11320981cbf81446b69288_00000000_cab_0764d745

Analysis symbol: 
Rechecking
for solution: 0
Report ID: 54413262-6e57-11e4-824e-c58295c96ec1
Report Status: 8
Hashed bucket: adb5d63b7478974f8d85c5ec03d74566
Sorted by: Device ID
Device Id
Chip Description
Vendor Id
Vendor Name
0x0191
SIS191
0x1039
Silicon Integrated Systems
0x0191
NVIDIA GeForce 8800 GTX
0x10DE
NVIDIA
0x0660
HD Audio
0x10EC
Realtek Semiconductor Corp
0x0191
CMI 8738 8CH Sound Card
0x13F6
C-Media Electronics Inc.
Maybe you are looking for
-
My Premiere Pro file crashed during closing and now PP will not open. I have uninstalled and reinstalled several times and it still doesn't work. I get the same message on another computer too. Thank you! I will miss a deadline if I can't get this to
-
Viewing .doc Attachment in Outlook Express
When receiving a MS Word .doc in Outlook Express, SunOffice Writer grabs the file and displays it instead of MS Word which is also on my Windows XP machine. Usually, it doesn't present the document as the sender had intended. How can I make MS Word t
-
Can you control the display on a Keithley 2400?
I have created a VI to control a Keithley 2400, but the enduser also wants to see results posted on the actual device. Is this possible?
-
Which first? Install Lion or Restore Settings?
We're shuffling computers around at work during a hardware/software overhaul. I'm preparing an iMac currently running 10.6 for use by another coworker. I plan to install 10.7 Lion (high as it can go) on the computer and want to run recovery mode an
-
Core dump at ::~RWCString
I am compiling with V5.0 compiler on solaris 2.6 I am getting the following core dump. I am using RogueWave with -library=rwtools7,iostream compiler option. The traceback from the core file is: signal SEGV (no mapping at the fault address) in RWRefer