My cpu has higher utilization
hi, my pc has slow down and i looked the running process. The oracle.exe has approximately %50 - 55 cpu utilization. Why this is higher? How can i decrease the cpu utilization of oracle.exe? Sometimes, this causes incresing of cpu temperature. Sometimes 65-70 degree. How can i solve this problem. thanx
( iam using pl sql developer, but cpu utilization isnt decreased whether i open plsql developer or not. )
hi, my pc has slow down and i looked the running
process. The oracle.exe has approximately %50 - 55
cpu utilization. Why this is higher? How can i
decrease the cpu utilization of oracle.exe?
Sometimes, this causes incresing of cpu temperature.
Sometimes 65-70 degree. How can i solve this problem.
thanx
( iam using pl sql developer, but cpu utilization
isnt decreased whether i open plsql developer or not.
)You can investigate what Oracle is using the CPU for with Database Control using the performance tab and the top sessions link. A CPU that gets to 65-70 degrees suggests that you have a cooling problem in the machine.
Niall Litchfield
http://www.orawin.info/
Similar Messages
-
WLC 7.0.98.0 CPU high utilization
I could not find anything wrong with the show tech on WLC. Client complaints CPU high utilization. Please help!
Hi Andrew,
There are a couple of interesting things in the debug output you included, firstly there are some unsupported rates by the clients, in other words do you have some 802.11b clients trying to connect? Because I think you may have unsupported the 'b' rates on the controller. So either - ensure you have no 'b' clients or start supporting 'b' rates again (1, 2, 5.5, 11)
Secondly there some rogue AP containment going on, this can cause either your AP to have a high CPU, f there are multiple rogue APs being contained, or it may be that your own clients are being de-authenticated by another wireless network in the area - in other words, your network is under attack.
HTH
Best wishes
Mike -
ITunes 10.6 has High CPU Usage when switched to Mini Player
iTunes has high CPU usage when switched to mini player. The CPU usage goes to 80-100% when the next song is played in Mini Player. iTunes then stays at high CPU usage.
Upon exiting mini player the CPU usage will drop back to the normal 0-5% levels.
This only happens when playing from the main music library; which my library is at 7089 items, 42.04 GB.
When playing from a smaller playlist such as a smart playlist with about 15 songs in it for example, the CPU usage stays low/normal.Do you have any better luck with that if you update to iTunes 10.6.1.7?
From the notes for the release:
iTunes 10.6.1 provides a number of improvements, including:
• Fixes several issues that may cause iTunes to unexpectedly quit while playing videos, changing artwork size in Grid view and syncing photos to devices.
• Addresses an issue where some iTunes interface elements are incorrectly described by VoiceOver and WindowEyes.
• Fixes a problem where iTunes may become unresponsive while syncing iPod nano or iPod shuffle.
• Resolves an ordering problem while browsing TV episodes in your iTunes library on Apple TV.
http://www.apple.com/itunes/download/ -
Dock process has high CPU usage after Mountain Lion upgrade
Dock process has high CPU usage after Mountain Lion upgrade and possibly after installing XCode as well.
When I run "sudo opensnoop -n Dock" I see the following being constantly repeated.
501 263 Dock 28 /Applications/Xcode.app
501 263 Dock 28 /Applications/Xcode.app/Contents
501 263 Dock 28 /Applications/Xcode.app/Contents/Info.plist
501 263 Dock 28 /Applications/Xcode.app/Contents/Info.plist
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources/English.lproj
501 263 Dock -1 /Applications/Xcode.app/Contents/Resources/Base.lproj
501 263 Dock 28 /Applications/Xcode.app/Contents/PkgInfo
501 263 Dock 28 /Applications/Xcode.app/Contents/MacOS/Xcode
501 263 Dock 28 /.vol/16777218/92542858
501 263 Dock 29 /Applications/Xcode.app/Contents/Library/Spotlight/uuid.mdimporter/Contents/Inf o.plist
501 263 Dock 28 /Applications/Adobe Dreamweaver CS5/Configuration/Shared/ICE/Templates
501 263 Dock 28 /Applications/Adobe Dreamweaver CS5/Configuration/Shared/MM
501 263 Dock 28 /Applications/Adobe Dreamweaver CS5/Configuration/Shared/MM/Cache
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources
501 263 Dock 28 /Applications/Xcode.app/Contents/Resources/English.lproj
501 263 Dock -1 /Applications/Xcode.app/Contents/Resources/Base.lproj
501 263 Dock 28 /Applications/Xcode.app/Contents/PkgInfo
501 263 Dock 28 /Applications/Xcode.app/Contents/MacOS/Xcode
501 263 Dock 28 /.vol/16777218/92542858
501 263 Dock 29 /Applications/Xcode.app/Contents/Library/Spotlight/uuid.mdimporter/Contents/Inf o.plist
501 263 Dock 28 /Applications/Adobe Dreamweaver CS5/Configuration/Shared/MM/Images
When I run "killall Dock" it resolves it for awhile and then comes back.Welcome to Apple Communities
https://discussions.apple.com/message/18825564#18825564 -
(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!
=================
i have a cisco router 7200 NPEG2 processor , worked as LNS for PPPOVPDN circuits (Router for ADSL clients)
i have "high ip input on my processor" and there is alot of differnce on my router between operations done by cef and operations done by router cpu
as an example , lets make show cpu process sorted
CPU utilization for five seconds: 67%/54%; one minute: 67%; five minutes: 68%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 10837056 46891299 231 6.31% 6.04% 6.32% 0 IP Input
122 4081972 38214106 106 2.47% 2.36% 2.46% 0 L2X Data Daemon
270 467844 2089101 223 0.79% 0.78% 0.79% 0 PPP Events
275 1862224 2102444 885 0.71% 0.73% 0.71% 0 SNMP ENGINE
112 627104 93588 6700 0.39% 0.36% 0.37% 0 CEF: IPv4 proces
273 854004 4207368 202 0.31% 0.26% 0.24% 0 IP SNMP
52 453256 12321 36787 0.31% 0.31% 0.31% 0 Compute load avg
258 295540 701580 421 0.23% 0.17% 0.15% 0 RADIUS
142 45792 14107303 3 0.23% 0.21% 0.21% 0 HQF Shaper Backg
78 86532 166975 518 0.23% 0.17% 0.13% 0 ACCT Periodic Pr
260 483164 248673 1942 0.23% 0.19% 0.24% 0 L2TP mgmt daemon
272 63980 1073491 59 0.15% 0.16% 0.15% 0 IPHC Admin
77 111560 184597 604 0.15% 0.08% 0.06% 0 AAA ACCT Proc
261 330572 217566 1519 0.15% 0.12% 0.15% 0 L2TUN Applicatio
274 450584 2102164 214 0.15% 0.15% 0.15% 0 PDU DISPATCHER
16 152352 1081873 140 0.07% 0.08% 0.19% 0 EnvMon
279 229040 27298 8390 0.07% 0.10% 0.11% 0 VTEMPLATE Backgr
40 23704 53593 442 0.07% 0.03% 0.02% 0 Net Background
95 4512 55604 81 0.07% 0.00% 0.00% 0 PPP Hooks
109 6844 62029 110 0.07% 0.00% 0.00% 0 IP Background
269 21384 1931910 11 0.07% 0.06% 0.07% 0 PPP manager
271 116 60672 1 0.07% 0.00% 0.00% 0 Multilink PPP
23 98400 321 306542 0.00% 0.07% 0.03% 0 AAA high-capacit
=====================
as we see above , we have high "IP Input" about differnece in cpu =67-54=13 % , which is high value process in software .
i follwed the article here :
http://www.cisco.com/c/en/us/support/docs/routers/7500-series-routers/41160-highcpu-ip-input.html
i check and found that my router is fine ,
no arp calls.
no routing loops.
no flapping links.
i checked that my router has cef enabled and no enormous routing protocol updates
i found that i have big differnce between hardware & software process on the router which is 13 %
but when the traffic is more and more , the cpu reach reach 93 % and begin to have drops.
i just want to ask , how can i debug the operations that are done on the cpu processor of the router ???
i mean that if i know that traffic , i can estimate and know the problem that increasing my cpu !!!
another question :
how to debug the packest that has a ttl exceeded 50 or ttl exceeded 100 ?????
i dont wan tto make debug ip packed , because i have a huge traffic and it will let my router hanged due to large debug !!
===============
righ now i will post my router config and some verification:
drvirus#sh running-config
Building configuration...
Current configuration : 12291 bytes
upgrade fpd auto
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service dhcp
hostname drvirus
boot-start-marker
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T7.bin
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T8.bin
boot-end-marker
logging message-counter syslog
aaa new-model
aaa group server radius radiusservers
server-private 10..f.f.f auth-port 1812 acct-port 1813 key 7 weifuhjkefkjdbhfjkasbfjka
aaa authentication login adminstaff local
aaa authentication login sdm_vpn_xauth_ml_1 group radius
aaa authentication login ahmad local
aaa authentication ppp vpdn group radiusservers local
aaa authentication ppp drvirus local
aaa authentication ppp vpdn1 local group radiusservers
aaa authentication ppp ddd none
aaa authentication ppp dddd none
aaa authentication ppp anyok none
aaa authorization network default group radius local
aaa authorization network vpdn group radiusservers local
aaa authorization network sdm_vpn_group_ml_1 local
aaa authorization network drvirus local
aaa authorization network vpdn1 local group radiusservers
aaa authorization network ddd none
aaa authorization network anyok none
aaa accounting delay-start
aaa accounting update newinfo periodic 10
aaa accounting network vpdn
action-type start-stop
broadcast
group radiusservers
aaa server radius dynamic-author
client xxxxxxxx
client 10.xxxxxx
client 10.xxxxxxxxx
server-key 7 dihcbsdjkbvcsdhmbvhsdbvsdhmbvsd
auth-type any
aaa session-id common
clock timezone GMT+3 3
no ip subnet-zero
no ip source-route
no ip gratuitous-arps
ip cef
no ip bootp server
ip domain name drvirus
ip name-server x.x.x.x.x
ip name-server 8.8.8.8
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
ipv6 dhcp pool vvv
prefix-delegation pool version6
address prefix 3333::/64
dns-server 4444::1
multilink bundle-name authenticated
vpdn enable
vpdn logging
vpdn logging local
vpdn history failure table-size 50
vpdn-group eeeeeeeeeeee
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname qqqqqq
local name rrrrrrr
lcp renegotiation on-mismatch
l2tp tunnel password 7ekfhjjeklfnlenfl
l2tp tunnel timeout no-session 60
ip mtu adjust
username drvirus@!34`!512&$8#$232!^@^FGsdGD privilege 0 password 7 000sdkjhvsdkjvnah94313085g2355091407458E32425D
interface Loopback1
ip address ttttttt 255.255.255.255
interface GigabitEthernet0/1
description ttttttt
ip address 10.60.60.2 255.255.255.0 secondary
ip address 10.200.200.200 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/1.4
encapsulation dot1Q 4
ip address ttttttttt 255.255.255.224
interface GigabitEthernet0/1.14
encapsulation dot1Q 14
ip address 192.168.50.3 255.255.255.0
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
ip address 10.160.150.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description rrrrrrr
ip address xxxxxxx 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
interface Virtual-Template1
ip unnumbered Loopback1
ip tcp adjust-mss 1412
no logging event link-status
peer default ip address pool xxxxx xxxxxx
ppp mtu adaptive
ppp authentication pap vpdn1
ppp authorization vpdn1
ppp accounting vpdn
router eigrp 2
redistribute connected metric 1 2 1 2 1
passive-interface default
no passive-interface GigabitEthernet0/1
network 10.200.200.200 0.0.0.0
no auto-summary
eigrp router-id 2.2.2.2
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.200.200.2
ip route dddddddddd 255.255.255.0 fffffff
ip route ddddddddd 255.255.255.0 ffffff
no ip http server
no ip http secure-server
ip radius source-interface GigabitEthernet0/2
radius-server attribute nas-port format d
radius-server configure-nas
radius-server host ddddddddddd auth-port 1812 acct-port 1813 key 7 dddddddddd
radius-server retransmit 0
radius-server key 7 dddddddddddddddddd
radius-server vsa send cisco-nas-port
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
drvirus#sh ip traffic
IP statistics:
Rcvd: 92454889 total, 5908020 local destination
0 format errors, 94 checksum errors, 3789577 bad hop count
0 unknown protocol, 23360 not a gateway
0 security failures, 0 bad options, 3730347 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 3730347 alert, 0 cipso, 0 ump
0 other
Frags: 1409002 reassembled, 485 timeouts, 0 couldn't reassemble
4542214 fragmented, 9089659 fragments, 2659413 couldn't fragment
Bcast: 6024 received, 0 sent
Mcast: 56503 received, 31033 sent
Sent: 15839581 generated, 2407203241 forwarded
Drop: 23 encapsulation failed, 0 unresolved, 0 no adjacency
0 no route, 0 unicast RPF, 0 forced drop
0 options denied
Drop: 0 packets with source IP address zero
Drop: 0 packets with internal loop back IP address
0 physical broadcast
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 4 unreachable
140579 echo, 33742 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 timestamp replies, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
0 time exceeded, 0 info replies
Sent: 0 redirects, 3530 unreachable, 33744 echo, 140579 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp, 0 timestamp replies
0 info reply, 46795 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements
TCP statistics:
Rcvd: 19285 total, 0 checksum errors, 7 no port
Sent: 39402 total
BGP statistics:
Rcvd: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh, 0 unrecognized
Sent: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh
IP-EIGRP statistics:
Rcvd: 39154 total
Sent: 39275 total
PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
Queue drops: 0
State-Refresh: 0/0
IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0
Queue drops: 0
UDP statistics:
Rcvd: 5632168 total, 0 checksum errors, 9605 no port
Sent: 15536481 total, 0 forwarded broadcasts
OSPF statistics:
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
ARP statistics:
Rcvd: 36012 requests, 25 replies, 0 reverse, 0 other
Sent: 3590 requests, 1883 replies (41 proxy), 0 reverse
Drop due to input queue full: 0
drvirus#sh interfaces switching
GigabitEthernet0/1 ffff
Throttle count 0
Drops RP 29334 SP 0
SPD Flushes Fast 183378 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 196591 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 50222652 1410586379 38933488 2377282438
Cache misses 0 - - -
Fast 2501299905 502401799 1732463443 1178236678
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 36178 2170680 3643 233084
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1039 385469 2067 772027
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 2266 138297 6179 370740
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
Interface FastEthernet0/2 is disabled
GigabitEthernet0/2
Throttle count 0
Drops RP 0 SP 0
SPD Flushes Fast 785 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 1900 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 382927 34296776 382540 106683985
Cache misses 0 - - -
Fast 198 31569 0 0
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1900 114000 1813 108780
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1030 378010 1031 378377
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
GigabitEthernet0/3 drvirus
Throttle count 0
Drops RP 15 SP 0
SPD Flushes Fast 22435 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 194236 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 40507058 2970006619 56462488 1872816742
Cache misses 0 - - -
Fast 1758170357 386468928 2449949282 3706868609
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 105 8085
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 5 300 7 420
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 1034 379478
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1644 105280 250040
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1644 105472 256356
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#
ANy help ??????!!!!!can some one determin if :
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
has a relation to my high cpu
her is agian my cpu process :
drvirus#sh processes cpu sorted
CPU utilization for five seconds: 69%/51%; one minute: 62%; five minutes: 59%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 22165548 147317354 150 7.60% 6.54% 5.74% 0 IP Input
16 682988 2637213 258 3.61% 0.70% 0.37% 0 EnvMon
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
270 484700 4987094 97 0.76% 0.84% 0.86% 0 PPP Events
260 746640 483367 1544 0.30% 0.51% 0.51% 0 L2TP mgmt daemon
112 1082540 228491 4737 0.30% 0.31% 0.31% 0 CEF: IPv4 proces
190 596 755 789 0.30% 0.02% 0.00% 2 SSH Process
279 461184 78909 5844 0.30% 0.39% 0.45% 0 VTEMPLATE Backgr
52 954592 29823 32008 0.30% 0.31% 0.31% 0 Compute load avg
272 53744 2782461 19 0.23% 0.17% 0.16% 0 IPHC Admin
261 513524 428266 1199 0.23% 0.38% 0.37% 0 L2TUN Applicatio
142 31888 35627222 0 0.23% 0.19% 0.20% 0 HQF Shaper Backg
258 570384 1602872 355 0.15% 0.18% 0.17% 0 RADIUS
78 43280 392561 110 0.15% 0.10% 0.08% 0 ACCT Periodic Pr
281 52340 385568 135 0.07% 0.08% 0.09% 0 IP-EIGRP: PDM
40 37300 138153 269 0.07% 0.09% 0.10% 0 Net Background
77 145860 443602 328 0.07% 0.06% 0.07% 0 AAA ACCT Proc
110 31060 53876 576 0.07% 0.03% 0.02% 0 IP RIB Update
45 11868 52400 226 0.07% 0.01% 0.00% 0 IF-MGR control p
115 20164 103667 194 0.07% 0.02% 0.00% 0 PPP IPCP
102 181600 489310 371 0.07% 0.14% 0.15% 0 SSM connection m
143 3148 1461382 2 0.07% 0.01% 0.00% 0 RBSCP Background
80 19488 22128 880 0.07% 0.02% 0.00% 0 CDP Protocol
23 189412 10771 17585 0.00% 0.15% 0.04% 0 AAA high-capacit
22 0 1 0 0.00% 0.00% 0.00% 0 CEF MIB API
21 0 2 0 0.00% 0.00% 0.00% 0 ATM Idle Timer
20 376 153594 2 0.00% 0.00% 0.00% 0 ARP Background
24 0 2 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
25 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
26 1376 26590 51 0.00% 0.00% 0.00% 0 DDR Timers
31 4 30 133 0.00% 0.00% 0.00% 0 EEM ED Syslog
27 0 5 0 0.00% 0.00% 0.00% 0 Entity MIB API
33 324 147392 2 0.00% 0.00% 0.00% 0 GraphIt
34 0 2 0 0.00% 0.00% 0.00% 0 Dialer event
28 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun
36 0 2 0 0.00% 0.00% 0.00% 0 XML Proxy Client -
How do I know if my CPU has decreased speed or what speed my cpu is running?
I recently noticed that when running PRO app my MBP seems pretty slow unusually. I have met this occasion before . I heard that when temperture is too high , the CPU will decrease its speed to protect itself. How do I know if my CPU has decreased speed or what speed my cpu is running?
Thank you!
MBP 8,2 10.6.8Enter in the search field of Google 'CPU speed monitors' and you should get some results.
Ciao. -
Hi.
Ive just upgraded my win 8.1 to win 10 technical preview. The first thing that bugged me was the process rundll32. It has high cpu usage (40-50% of my cpu). It didnt have that on win 8.1, and i havent done anything other than upgraded to win 10. Anyone else
having trouble with this?Until you have RTM you can be surprized...
To dig deeper try to use Sysinternals tools, namely Process Explorer is you primary tool (hope is will work in W10):
https://technet.microsoft.com/cs-cz/sysinternals/bb896653.aspx
HTH
Milos -
I had a lot of bills this tax month and I am going to carry a balance for the first time ever. It's on a 0% APR card which is the only reason I'm carring a balance. Keeping the cash I could pay it off in a 3.25% APY account. My utilization was always 4-8% each month. For this month my statements cut and I had 35% utilization. The following happened to my scores FICO TU reported by Barclay 696 dropped to a 674FAKO TU by Credit Karma 684 droped to a 635 I'm going to pay all my cards off at the end of this billing cycle except for my 0 APR card. I will pay that off the following month. I'll repost my scores as they change.
degs138 wrote:
So here is where I am at. I was at 35% utilization in May with one card at 85% utilization. My score dropped to 651 at the worst. FICO score reported by Barclays. I paid off my cards in June so I was reporting a 16% utilization. My score went up to 699. Next month I will end up paying off my balances and get my utilization down to under 10%. hoping to be back in the 700s. I'll update the thread when I get my next score update. I couldn't believe I went form 709 to 651 with high utilization on one card. That is a drop of 58 points for using close to the limit on one card.I see that you have two Cap 1 cards. Take a look at their balance transfer offers. I also have a Venture and QS. Each one provides me with no fee balance transfers. Depending on when your statements close, it might be beneficial for you to transfer the balance onto one of them if there is no fee. That could movet the balance early and increase your scores when the other card reports zero. Then pay the Cap 1 down before it reports the higher balance. I have my statement closing dates spread out. This has helped me when I wanted to float something for a month. Didn't have to pay intrerest or see a score decrease. -
My Profile - Fico 8 - High Utilization
I have decided to post my profile and will update as changes are made. I have what I would call a very stable profile. My oldest card, depending on which bureau, ranges from 28.8 to 35.2 years. My average age ranges from 15.8 to 17.9 years. My two newest cards just turned 8 years on July 1st. The only inquiry I have will be 2 years old on July 26th for a phone service. On 2/25/15, I started to be more aware of account balances and did not let a single one increase since then. In the past, I have had balances go up or down but never increased my total utilization. I have one $30 paid medical collection from Oct 2012 and one 30 day late payment which will be 5 yrs on Aug 1st. EX and EQ have both of these shown and TU has neither. My accounts are as follows: 2/25/15 6/9 cards w/balances 44% utilizationBoA 95% utilChase Freedom 62%Chase Slate 37%USAA 93%Universal 24%Kohls $50.00 Scores: EQ 724 TU 734 EX 728 2/26/15Paid USAA down to 93% Scores: EQ 731 TU 734 EX 731 From 2/26/15 to 5/26/15 there were no score changes. During that time I paid the $50 balance on Kohls so had 5/9 cards reporting and brought USAA down to 89%. The Chase Freedom also went below 60% 5/26/15 5/9 cards reporting 41% utilizationBrought BoA down to 89% utilization. Scores: EQ 735 TU 744 EX 734 Sometime between 5/26/15 and 6/14/15, my EX went up to 738 with no alert triggered. From 6/23/15 to 6/26/15, my EX score went up and down each down from 738 to 742 then back down and back up. It finally settled at 742 on 6/28. I pulled the 3B on CCT on 7/3/15 and scores were as follows: Scores: EQ 735 TU 744 EX 745 My EX increased 3 points on 7/1/15 which is when my average age went to 18 yrs. EX increased 1 point on 7/12/15 which is when my two newest cards turned 8 yrs. Current Scores: EQ 735 TU 744 EX 746 Of interest is the fact that EX is 2 points higher than TU and TU doesn't have the late payment or collection. To me, this shows that the high utilization is a bigger factor than the late payment and collection. I have paid USAA down to 78% and will be running a 3B on CCT as soon as it reports, which should be in the next few days. I have also paid BoA down to 79% and will run a 3B when that reports, which should be around the 26th. I also have a heloc at 32% and a mortage at 78%. No installment loans. I will have to check my total and individual utilization to see where it's at on all of the cards. Hope this all makes sense. Will update as changes occur. I am not looking for any advice as I have a solid plan on paying off my cards and many of these are at 0%or low rates. Only one is a higher rate and I will get back to paying that at an accelerated rate now that the two high utilization cards are below 80%.
cj1132 wrote:
I have decided to post my profile and will update as changes are made. I have what I would call a very stable profile. My oldest card, depending on which bureau, ranges from 28.8 to 35.2 years. My average age ranges from 15.8 to 17.9 years. My two newest cards just turned 8 years on July 1st. The only inquiry I have will be 2 years old on July 26th for a phone service. On 2/25/15, I started to be more aware of account balances and did not let a single one increase since then. In the past, I have had balances go up or down but never increased my total utilization. I have one $30 paid medical collection from Oct 2012 and one 30 day late payment which will be 5 yrs on Aug 1st. EX and EQ have both of these shown and TU has neither. My accounts are as follows: 2/25/15 6/9 cards w/balances 44% utilization Scores: EQ 724 TU 734 EX 728 2/26/15Paid USAA down to 93% Scores: EQ 731 TU 734 EX 731 From 2/26/15 to 5/26/15 there were no score changes. During that time I paid the $50 balance on Kohls so had 5/9 cards reporting and brought USAA down to 89%. The Chase Freedom also went below 60% 5/26/15 5/9 cards reporting 41% utilizationBrought BoA down to 89% utilization. Scores: EQ 735 TU 744 EX 734 I pulled the 3B on CCT on 7/3/15 and scores were as follows: Scores: EQ 735 TU 744 EX 745 Current Scores: EQ 735 TU 744 EX 746 I have also paid BoA down to 79% and will run a 3B when that reports, which should be around the 26th. I also have a heloc at 32% and a mortage at 78%. No installment loans. I will have to check my total and individual utilization to see where it's at on all of the cards. Hope this all makes sense. Will update as changes occur. I am not looking for any advice as I have a solid plan on paying off my cards and many of these are at 0%or low rates. Only one is a higher rate and I will get back to paying that at an accelerated rate now that the two high utilization cards are below 80%. Thanks for sharing your data. Your AAoA is impressive. You may want to pay off low balance cards to get the # of cards reporting a blance down to three from five. The % of cards reporting can be a significant factor on scoring. The primary factor keeping your score down appears to be aggregate utilization percentage. A couple thresholds I have wondered about are 35% and 20%. You are approaching the 35% mark. Utilization on individual cards - at least up to 80% - has not been shown to impact Fico 8 score. It would be interesting to try and isolate impact on score associated with each of the following if your pay down schedule allows:1) Any step change in score as aggregate utilization drops2) Any step change in score associated with reducing % or # of cards reporting a balance -
IMac has high temperatures at all times
My iMac has high temperatures at all times lately. I realized this after it began randomly freezing, and so I installed iStat Pro and saw the temperatures seemed higher than usual.
Here they are (all temperatures are in Celsius degrees):
HD: 53
CPU: 52
Ambient: 30
GPU Diode: 71
GPU Heatsink: 66
Mem Controller: 60
Optical Drive: 52
Power supply 2: 75
Fan speeds:
Optical drive: 1110 rpm
Hard drive: 1100 rpm
CPU fan: 1421 rpm
I imagine these are quite a bit on the high side? These are also pretty constant, meaning even when I've just got iTunes and Firefox open (as I do now), these are the values that I get.
Anything I can do about this? I assume that AppleCare wouldn't do much about this unless something dies inside my computer, such as the fans failing or something?I think the HD and CPU temps are running a TAD high, IMO.
The iMac's fans don't ramp up fast enough to keep both the HD and CPU cool enough.
I like to see both the HD and CPU temps below 50 degrees C during semi-normal operations.
I think iMac's run too warm/hot causing a " slow roasting" of various internal components over not so long a time.
If you are worried like I do, you can install an iMac fan control app called SMC Fan Control.
This little app will allow you ramp up the iMac's minimum fan speeds to a faster rpm than what Apple has set the default minimum rpm speed to be.
You want to use and set the fan speed conservatively to prevent premature burn up of the fan motors and to minimize sucking in additional dust, dirt and lint into your iMac.
When using this app create a new default user setting and set the fans rpm speeds to between 200-600 rpm higher/faster than the Apple default speeds. My recommendation is not to run the fans over 2000 rpm.
If both the HD and CPU still run at a higher temp., you can try a slightly higher settings for these between 1600 to 1800 rpm.
These settings keep the iMac and the fans relatively quiet, minimizing the amount of extra dust, dirt and lint into your iMac and allow these components to run at a more acceptable or tolerable temperature.
Another thing that can help with the heat buildup.
As old as your iMac is, have you cleaned out the dust? Dust buildup can lead to over heating issues. Remove any and all things plugged into it including the power cord, Remove the RAM access grille. Vacuum all openings starting with the RAM access area (air intake). Vacuum all ports and plugs, DVD slot and the opening across the top of the rear of the body. Plug in the keyboard and mouse if not blue tooth. Insert power cord...
Also, it wouldn't hurt to run a small fan behind the iMac blowing on the back panel of the iMac.
I do this, as well.
Good luck! -
How to find CPU and Memory Utilization
Hi,
How to find CPU and Memory Utilization of my application which is
running in solaris workstation.My application has a management console in which we need to update the cpu and memory periodically.
(Notr : Usage of JNI is restrcited)
Thnx and Rgds,
MohanThere is no CPU usage API in Java. You need some JNI code. For memory usage see the Runtime methods:
* Get information of memory usage: max, total, free and (available/used).
* <ul>
* <li>Max is the maximum amount of bytes the application can allocate (see also java options -Xmx). This value is fixed.
* If the application tries to allocate more memory than Max, an OutOfMemoryError is thrown.
* <li>Total is the amount of bytes currently allocated from the JVM for the application.
* This value just increases (and doesn't decrease) up to the value of Max depending on the applications memory
* requirements.
* <li>Free is the amount of memory that once was occupied by the application but is given back to the JVM. This value
* varies between 0 and Total.
* <li>The used amount of memory is the memory currently allocated by the application. This value is always less or equal
* to Total.
* <li>The available amount of memory is the maximum number of bytes that can be allocated by the application (Max - used).
* </ul>
* In brief: used <= total <= max
* <p>
* The JVM can allocate up to 64MB (be default) system memory for the application. If more is required, the JVM has to be started with the Xmx option
* (e.g. "java -Xmx128m" for 128 MB). The amount of currently allocated system memory is Total. As the JVM can't give back unallocated memory
* to the operating system, Total can just increase (up to Max).
* @return Memory info.
static public String getMemoryInfo() {
StringBuilder sb = new StringBuilder();
sb.append("Used: ");
sb.append(toMemoryFormat(getUsedMemory()));
sb.append(", Available: ");
sb.append(toMemoryFormat(getAvailableMemory()));
sb.append(" (Max: ");
sb.append(toMemoryFormat(Runtime.getRuntime().maxMemory()));
sb.append(", Total: ");
sb.append(toMemoryFormat(Runtime.getRuntime().totalMemory()));
sb.append(", Free: ");
sb.append(toMemoryFormat(Runtime.getRuntime().freeMemory()));
sb.append(")");
return sb.toString();
}//getMemoryInfo() -
I feel 8.02 is less responsive and has higher latency!
After installing 8.02 and 10.5.3, Logic feels less snappy, has higher latency and has graphical glicthes when a big project is loaded.
Also, when recording in loop mode and when the playback cursor goes back to the beginning of the loop, the recorded notes are all messed up (like Ableton Live)
Also, when dragging a selection in the arranger, the (dragged) selection jumps all the way up or down? (bug?)
8.02 has various other tiny glitches.
Also, the Sculpture synth uses way more CPU since the update!
Good thing: projects load up extremely fast
I have no problems with the Overload Message but then again, I never saw them, ever in 8.0 or 8.01
I did a repair permission before and after each update (update OSX, Logic and Apogee Duet) and flashed the PRAM after all the updates.
I do not use third party plugins.
What am I doing wrong? Because I read all good things about the new Apple updates. However, I am not experiencing them, except for the faster loading timesI have the same latency problem since updating, and only in Logic (not Cubase). I reduced the midi latency when I uncheck, "Universal Track Mode," which is supposed to remain checked, in Audio pref., and turning off any sends on that track while recording.
Now there's a whole new problem of rerouting outputs to high number Double busses (bus 29-30) that never existed before when I reopen a project or start a new one from a template. -
HU03 going to short dump for handling unit which has higher level handling
Hi,
I am ABAPer, i working on issue, HU03 is gong to short dump. i dubug the t code and find out that particular handling unit has higher level handling unit. I checked another handling unit which won't had higher level handling unit, that time it's not giving dump.
Note: in HU03 T CODE, function module V51P_HU_CONTENS is fetching values. when ever handling unit has higher level handling unit, it's not fetching further values.
venkeyHi,
Goto NACE transaction code , there you select the application area then it will give you the list of output types then select specific output click processing routines then you will see the program name and script used.
Or esle goto SPRO tcode then you can find the functional tab there also you can get the details.
Thanks,
Aditya -
Only one CPU core high sys usage when create database instance via dbca
when using dbca to create database instance
JUST ONLY ONE CPU core high sys usage
how to troubleshoot it
see this:
top - 09:28:19 up 55 days, 20:38, 10 users, load average: 1.00, 1.08, 1.31
Tasks: 1231 total, 2 running, 1228 sleeping, 0 stopped, 1 zombie
Cpu(s): 0.0%us, 1.3%sy, 0.0%ni, 98.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 57588328k total, 55028620k used, 2559708k free, 196852k buffers
Swap: 16386292k total, 23156k used, 16363136k free, 23011232k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
11343 oracle 25 0 1771m 30m 23m R 99.7 0.1 5:36.39 oracle
3692 oracle 16 0 13948 2348 816 S 1.6 0.0 17:00.94 top
11432 root 15 0 13540 2024 820 R 1.3 0.0 0:00.21 top
11034 oracle 16 0 737m 171m 33m S 0.3 0.3 0:52.39 java
11435 oracle 15 0 66056 1596 1180 S 0.3 0.0 0:00.01 bash
1 root 15 0 784 172 160 S 0.0 0.0 38:56.76 init
2 root RT -5 0 0 0 S 0.0 0.0 0:00.58 migration/0
3 root 34 19 0 0 0 S 0.0 0.0 0:00.75 ksoftirqd/0
4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0
5 root RT -5 0 0 0 S 0.0 0.0 0:00.81 migration/1
6 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/1
7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1
8 root RT -5 0 0 0 S 0.0 0.0 0:02.53 migration/2 mpstat info
[root@localhost ~]# mpstat -P ALL 2
Linux 2.6.18-164.el5 (localhost.localdomain) 09/12/12
09:29:09 CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
09:29:11 all 0.01 0.00 1.27 0.01 0.00 0.01 0.00 98.69 1658.29
09:29:11 0 0.50 0.00 0.00 0.00 0.00 0.50 0.00 98.99 1657.29
09:29:11 73 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 74 0.00 0.00 100.00 0.00 0.00 0.00 0.00 0.00 0.00
09:29:11 75 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 76 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 77 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 78 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 79 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
09:29:13 all 0.01 0.00 1.26 0.01 0.00 0.02 0.00 98.70 1761.19
09:29:13 0 0.50 0.00 0.50 1.00 0.00 1.99 0.00 96.02 1761.19
09:29:13 71 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 72 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 73 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 74 0.00 0.00 100.00 0.00 0.00 0.00 0.00 0.00 0.00
09:29:13 75 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 76 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 77 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 78 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:13 79 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00 you can see there is only one CPU CORE (core 74 but is random , other core have same status but just one CPU core)
[root@localhost ~]# vmstat -S m 2
procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------
r b swpd free buff cache si so bi bo in cs us sy id wa st
3 0 23 1861 203 24267 0 0 8 12 0 0 0 0 99 0 0
4 0 23 1845 203 24262 0 0 602 16460 3682 8121 2 2 96 1 0
3 0 23 1842 203 24276 0 0 692 7520 3297 6610 2 2 97 0 0
3 0 23 1830 203 24277 0 0 786 3040 3302 7118 2 2 97 0 0
4 0 23 1829 203 24277 0 0 126 3144 3247 7343 2 1 97 0 0
3 0 23 1827 203 24279 0 0 76 2944 3292 7502 2 2 96 0 0
3 0 23 1823 203 24281 0 0 0 3248 3164 7656 2 1 97 0 0
2 0 23 1827 203 24279 0 0 0 3646 3080 7480 2 1 97 0 0
2 0 23 1828 203 24279 0 0 0 476 2942 5648 1 1 98 0 0
3 0 23 1824 203 24281 0 0 2 7476 3377 8111 2 2 97 0 0iostat infor
avg-cpu: %user %nice %system %iowait %steal %idle
1.28 0.00 1.29 0.00 0.00 97.43
Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn
hda 0.00 0.00 0.00 0 0
sda 5.47 0.00 83.58 0 168
sda1 0.00 0.00 0.00 0 0
sda2 5.47 0.00 83.58 0 168
sda3 0.00 0.00 0.00 0 0
sda4 0.00 0.00 0.00 0 0
sda5 0.00 0.00 0.00 0 0
sdb 8.96 0.00 123.38 0 248
sdb1 8.96 0.00 123.38 0 248
avg-cpu: %user %nice %system %iowait %steal %idle
1.27 0.00 1.27 0.00 0.00 97.46
Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn
hda 0.00 0.00 0.00 0 0
sda 0.00 0.00 0.00 0 0
sda1 0.00 0.00 0.00 0 0
sda2 0.00 0.00 0.00 0 0
sda3 0.00 0.00 0.00 0 0
sda4 0.00 0.00 0.00 0 0
sda5 0.00 0.00 0.00 0 0
sdb 17.50 0.00 236.00 0 472
sdb1 17.50 0.00 236.00 0 472
avg-cpu: %user %nice %system %iowait %steal %idle
1.29 0.00 1.30 0.01 0.00 97.41
Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn
hda 0.00 0.00 0.00 0 0
sda 0.50 0.00 16.00 0 32
sda1 0.00 0.00 0.00 0 0
sda2 0.50 0.00 16.00 0 32
sda3 0.00 0.00 0.00 0 0
sda4 0.00 0.00 0.00 0 0
sda5 0.00 0.00 0.00 0 0
sdb 7.50 0.00 144.00 0 288
sdb1 7.50 0.00 144.00 0 288more detail:
database version 11.2.0.2.0
system version
[root@localhost ~]# cat /etc/issue
Red Hat Enterprise Linux Server release 5.4 (Tikanga)
Kernel \r on an \m
[root@localhost ~]# lsb_release
LSB Version: :core-3.1-amd64:core-3.1-ia32:core-3.1-noarch:graphics-3.1-amd64:graphics-3.1-ia32:graphics-3.1-noarch
[root@localhost ~]# uname -a
Linux localhost.localdomain 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linuxhardware info
vendor_id : GenuineIntel
cpu family : 6
model : 47
model name : Intel(R) Xeon(R) CPU E7- 4860 @ 2.27GHz
stepping : 2
cpu MHz : 2261.057
cache size : 24576 KB
physical id : 3
siblings : 20
core id : 18
cpu cores : 10
apicid : 229
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx pdpe1gb rdtscp lm constant_tsc ida nonstop_tsc pni monitor ds_cpl vmx smx est tm2 cx16 xtpr popcnt lahf_lm
bogomips : 4522.11
clflush size : 64
cache_alignment : 64
address sizes : 44 bits physical, 48 bits virtual
[root@localhost ~]# free -m
total used free shared buffers cached
Mem: 56238 55892 346 0 196 23645
-/+ buffers/cache: 32050 24188
Swap: 16002 22 15979
[root@localhost ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 19G 4.9G 14G 27% /
/dev/sda5 230G 27G 192G 12% /home
/dev/sda1 99M 12M 83M 13% /boot
/dev/sdb1 2.9T 2.3T 464G 84% /arrayEdited by: JOhnLiu on Sep 11, 2012 7:31 PMJOhnLiu wrote:
thanks for reply sb92075
[root@localhost ~]# mpstat -P ALL 2
Linux 2.6.18-164.el5 (localhost.localdomain) 09/12/12
09:29:09 CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
09:29:11 all 0.01 0.00 1.27 0.01 0.00 0.01 0.00 98.69 1658.29
09:29:11 0 0.50 0.00 0.00 0.00 0.00 0.50 0.00 98.99 1657.29
09:29:11 73 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 74 0.00 0.00 100.00 0.00 0.00 0.00 0.00 0.00 0.00
09:29:11 75 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00
09:29:11 76 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 0.00I think you don't understand what i mean .
there just have ONLY ONE CORE %sys 100
the top command show average of all cpu core sys% usage
when the one core sys% is 100%
the system are very slow .
e.g: when I create a database instance used for a long time . over 2 hours
but generally it will be done at most 1 hours or shorteris any type of OS virtualization involved in this environment? -
SNMP OID for CPU and Memory Utilization on a MDS 9509
Does anyone know what the OIDs are for CPU and Memory utilization on a MDS 9509?
ThanksCISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
Once you feel as though you are on the right track, have a look at:
http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
I gather that what you need is:
1.3.6.1.4.1.9.9.305.1.1.1
and
1.3.6.1.4.1.9.9.305.1.1.2
Enjoy.
Stephen
Maybe you are looking for
-
Officejet L7780 will not install wirelessly on network.
Officejet L7780 trying to install wirelessly on Windows 7 64 bit machine. I have an AT&T 2Wire router, and I am running MacAfee on my PC. In the past I could install, but the printer would disappear and need to be reinstalled. I have upgraded the
-
Report for the account of vendor invoices not received ?
Hi friends; Is there a report or a transaction that would list the details (expense accounts, cost center an amounts) in the account of vendor invoices not received ? Thinks
-
Black screen w/blinking cursor hp dv6700 please help me out someone!!
My dv6700 running vista 32 bit has shut down on me and when i try to start it I get the first HP screen and then get stuck on a black screen with blinking cursor.....so i can't get to the next screen to press F8.....I went to this page to download is
-
I have some applications that are windows only. I want to install windows 7 on my external hard drive and boot to it when I need to use my windows applications. Is this possible with a mac and, if so, how can I do that? I have a 64-bit Macbook Pro ru
-
How to create a Share with selective access to subfolder?
Hi All! Just purchased PX12-400r and now "trying" to setup shares. What I want to accomplish is to have a Share accessible to one departmant (Finance). Inside that Share, I want to create sub-folders that is only accessble to specific employee and th