My Droid Razor HD updated yesterday. Now it will no longer connect to the bluetooth in my car

Yesterday I accepted the update for my Droid Razor HD. Now it will not connect to the Bluetooth in my car (worked for the previous 8 months).

Christin - Generally your pairings will still be in a list under BT on your phone. Unless of course, you performed a Factory Data Reset on the phone.
Your car's radio should have a reset capability. The front panel on my SONY comes off, and there's a reset button there. Do you have documentation that came with the car for the radio, or if an aftermarket radio, for the radio itself? If not, there is generally information on the web that you can Google to find the reset procedure.
HTH.

Similar Messages

  • Since updating my ipad it will no longer connect to the internet

    since i've updated my software on my ipad it will no longer connect to the internet. my husbands iphone will not connect either. my laptop connects immediately and my internet signal is full strength. is there something we are missing?

    Hello dchoffa,
    Thank you for using Apple Support Communities!
    I would start with this troubleshooting from the article named:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    If the above troubleshooting does not resolve the issue, I would next try the troubleshooting in one of the other sections down toward the bottom that fits your scenario.
    Regards,
    Sterling

  • I recently installed the 5.5.3 AirPort Utility update and my airport will no longer connect to the internet.

    I recently updated my macbook's AirPort Utility to 5.5.3 and it will no longer connect to wireless networks.  First let me explain everything I have done already, I have reset my router, and tried on other's (my friends and my schools) networks.  I have been able to succesfully connect to my friends wireless (router is made by netgear), but when i try to connect to my network (WRT54G linksys router) and my schools network (im unaware what they use for routers) I am unable to connect, and my AirPort will proceed either state it does not have an IP address and will assign itself one and will not connect to the internet.  It will connect to the network with an IP, but will be unable to connect to the internet with the browser claiming DNS lookup failure. 
    yes, I have deleted and changed my location,
           deleted the selected service.
           tried resetting my router
           cleared my PRAM / NVRAM
           installed the newest firmware onto my WRT54G
           Renewed my DHCP lease
           made sure my Configure IPv4 is using DHCP
          and theres a few more but i'm forgetting them.  
    Any suggestions on why the 5.5.3 update might of screwed up my airport?

    If everything else is connecting with no issues, I would go into the wifi setting on the iPad and redo the info there, user, password and anything else related to your wifi at your house.
    It is possible whatever he reset may have reset something to default setting which will not allow it to connect. If you need too then verify the wifi setting by comparing it with another device setting that works on your home network.
    Good luck

  • Since updating my iphone 4s to the most recent update it will no longer connect to the wifi at work, where i am not a network  administrator. All helps for this issue instruct turning off the router/other stuff that i cant access.Suggestions?

    Since updating my iphone 4s to the most recent update it will no longer connect to the wifi at work, where I am not a network administrator and do not have privliges to reset passwords and turn the routers on and off. Any other suggestions for re-connecting? I have never had a problem before and can still connect to other networks i am a part of...

    Try Resetting your iPad: Hold down the sleep and home buttons, wait for the Apple logo, let go of the buttons.

  • HT1766 When I go to settings on my iPhone 5 and hit the "bluetooth" tab, The  circular icon next to "Devices" is constantly "spinning", and now my phone will not connect to the bluetooth in my car, etc. Does anyone know how to fix this?

    when I go to "settings" on my iPhone 5 and hit the "Bluetooth" tab, the circular icon next to "Devices" is constantly spinning, ans now I can't get the phone to sync with the bluetooth in my car, etc.
    Any ideas on how I can correct this?

    unpair your phone from your car, then do a re-pair.

  • My iPad mini iOS version is 6.0.2  I can't upgrade to iOS 7.  Message displayed is "Verification of update failed because you are no longer connected to the internet."  This happens while I am connected to the internet.  What should I do?

    My iPad mini iOS version is 6.0.2 which I can't upgrade to iOS 7.  Message displayed during verifying upgrade is "Can't verify upgrade because you are no longer connected to the internet". This happens again and again though I am connected to the internet through wifi.  What should I do?

    Reset the iPad and try again. Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    Reset your router and try again. Unplug your router from power for about 30 seconds then plug it in again.
    Try another WiFi Network. Go to a friend's house, a library, anywhere else that you can use a trusted WiFi network.
    Try updating using iTunes on your computer.

  • I recently updated to latest iTunes and now my pc freezes.  I have a Tosiba 32bit running Windows Vista. Itunes will no longer connect to the store and I get error 42408 when opening ITunes. Please help!!

    When I open iTunes I get the error message 42408.
    I have googled and tried various solutions including
    - uninstalling, downloading and reinstalling. I have done that about 5 times.
    - sending the desktop icon to the rubbish bin and recreating a shortcut.
    - de-authorising the audible account. My computer goes thru the de- authorisation process and says that the account is deauthorised then when I go to re-authorise under Advanced all that is showing is to de-authorise the account. Weird.
    - contacted a tech guy locally and he has no clue. He's thinking it's probably a conflicting software problem. Obviously.
    I have to uninstall the iTunes program just so I can use the internet as the new version slows/freezes everything and makes doing anything on my computer ridiculous.
    Everything on my computer runs fine when Itunes is uninstalled. Great. not.
    I would appreciate some further guidance as unfortunately iTunes seems to have complete control over my life. LOL! Basically if iTunes fails the rest follows... It's a dominoe effect...

    Update:
    I contacted Apple Support and they agreed to waive the $40.00 tech support charge this one time which was very nice condsidering their update caused major problems with my computer. I realise I don't have to accept the updates but when they are released world wide to the public I do expect them to work relatively smoothly.
    To cut a long story short after following the tech support advice and uninstalling and reinstalling itunes 10.5 for the seventh time and more than a week of going in circles and days spent away from my business trying to fix the problem - I gave up.  Because, as a non computer geek,  (no offense - I think cg's are amazing)  what I need is a functioning computer and phone to run my business that can be both relied on - all the time. That is what I paid for and expected when I bought Apples' very smart iPhone - I did not expect to be plagued by an update to a program that causes chaos for over 7 days. (And to be frank I've had problems with iTunes for the whole time I have been using it. From importing cd's to purchasing problems. gah!)
    I may be one tiny person in a very large universe but I believe a certain standard can and should be expected when handing over hard earned cash to a company with a good reputation.
    I'm very disappointed with Apple.
    Unfortunatley they have lost a customer...
    This is how I fixed the problem:
    Yesterday I bought a new smartphone - the Samsung Galaxy phone uses the Android Market and the Kies program. The phone is as good as if not better than the iPhone. The Kies program runs very smoothly on my computer. Downloading Apps is a breeze. My new phone is about the same size as the iPhone and a tad lighter.
    Problem solved!
    As a side note - I will now save about $250.00 per year on my new prepaid phone plan with Boost compared to staying with my previous post-paid plan. I also get unlimited standard national calls in Australia plus unlimited texting too! Not bad for $40.00 a month.
    While this solution worked for me it may not suit everybody.

  • I shouldn't have done the update because now desktop will no longer run

    I have spent the last 6 hours trying to fix this.  I ran the available update yesterday and now as soon as I plug my Bold 9900 in, I get an error message and it does not sync.  I decided to try to reinstall the 7.1 update directly from the BB website to ensure if the update was corrupt, I could try to repair it.  Instead, I get an Error 1723.  I noticed that I still had an old 5.0 version of desktop on my PC, so tried to uninstall that doing a clean uninstall and get an Error 1316 message.  When I try to follow the instructions under KB04272, again going through the Control Panel does not work as the uninstall will not work as there is obviously a file missing.  I tried renaming the installshield, I tried repairing both the old version and the 7.1 version.  I am now at the point that I have both on my PC still and I cannot uninstall or repair or install either of them! 
    I would like to find a solution beside wiping my whole machine, but after this much time, I'm thinking wiping my machine or tossing the phone are pretty much where I want to go.  Can anyone suggest and alternate for me?
    Thanks

    i went through everything that i had changed since it last worked, it turns out it was some software installed with my new webcam that was preventing both firefox and utorrent from starting. the windows update restarted the computer for the new software to start working. All fixed now as the software was non- important

  • Updated firefox, now I am unable to connect to the internet via mozilla but other browsers still work

    When mozilla asked my for an update several months ago I chose to skip the install and wait. Did the install soon after and firefox stopped working even though my connection to the internet is fine. I uninstalled mozilla firefox, used another browser to access the mozilla website to reinstall firefox. This fixed my problem and firefox was working again, until another update came along. This time attempting to uninstall and reinstall did nothing. Once again I am left using another browser to use the support forum and firefox is not working. Please help!!

    That is an indication that a firewall is blocking the new version of Firefox. For details see [[Firefox cannot load websites but other programs can]].

  • I just downloaded the newest IOS software and now my iPhone5 won't pair with the Bluetooth in my car (the car system says it's paired when I try to re-pair it but then when n try to make a call it tells me it doesn't recognize the phone.

    I just downloaded the IOS upgrade, 7.0.2, and now my iPhone 5 won't pair with my Bluetooth in my car, despite repeated attempts to re-pair the two and despite the fact it's been paired fine previously.  The car system tells me it's paired but then when I try to make a call I get another message that says there is no paired phone.

    You can't override it no matter what you do. The device has to connect to the server to complete the iOS update. You could try rebooting the iPad and see if that lets you connect to the server after it starts up.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    If that will not work, you can try connecting to iTunes on your computer and see if the activation will complete. Sometimes when thes activation issues arise, you end up having to restore the device again, but first things first. Reboot and see what happens.

  • My iPad 2 will no longer connect to the internet after iOS 6 update

    HELP!! My iPad doesny connect tot the internet anymore. I down loaded iOS 6 today (9/19/12) and now it doesnt connect tot the internet anymore.

    Hello dchoffa,
    Thank you for using Apple Support Communities!
    I would start with this troubleshooting from the article named:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    If the above troubleshooting does not resolve the issue, I would next try the troubleshooting in one of the other sections down toward the bottom that fits your scenario.
    Regards,
    Sterling

  • Once i updated my itunes i can no longer connect to the internet thru it i.e. itunes store access is gone

    ever since i updated my itunes Yesterday!! i cannot do anything on it involving the internet it says an unknown error occurred (310) make sure your network connection is active and try again

    Hi Mopar_Agent,
    Thanks for using Apple Support Communities. Based on what you stated, it sounds like can't connect to iTunes Store. I would recommend that you read this article, it may be able to help the issue.
    Can't connect to the iTunes Store - Apple Support
    "iTunes could not connect to the iTunes Store. Make sure your network connection is active and try again." 
    Cheers,
    Mario

  • Updated my iTunes, iPhone will no longer connect. USB Cord is new, and laptop is new too. iTunes on my Work PC is not updated and connects fine to iPhone. What's Wrong?

    I need advice on this. I have looked at most communities and almost none answer my questions, I have restarted my computer a billion times and I have a brand new USB Cord, the only thing I have done is updated iTunes. (FYI:I have an iPhone 4, works fine, only thing is it won't connect to my computer anymore) And like I said, my work PC has a un-updated version of iTunes on it and my iPhone connects fine, maybe iTunes software is problem?

    The following may help:
    Windows computer: iOS: Device not recognized in iTunes for Windows
    Mac computer: iOS: Device not recognized in iTunes for OS X

  • I just updated my iPad to the iOS 6. My iPad will no longer connect to the Internet.

    Help! My wifi says its connecting and then immediately goes off.

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
     Cheers, Tom

  • TS3581 iOS 6.1 update - iPhone will no longer connect/pair with my car.  Is there a workaround for this issue?

    After the 6.1 update my iPhone 4S will no longer connect with my car stereo (2012 Chevy Sonic).  Until update, everything was working fine and I experienced no such issues.  I have tried deleting my phone from my stereo memory and re-pairing, but I get a pair unsuccessful error on my iPhone; I have been able to pair a pre-6.1 iPhone successfully after discovering the problem.  Has anyone found a workaround to this issue?

    IIRC updating the iPhone iOS changes its characteristics when viewed by vehicle
    bluetooth
    That is why you need to remove pairing from both ends and start again
    Vehicle just does not recognise the iPhone as the one it previously paired with

Maybe you are looking for

  • Problem(?) with BAPI BAPI_PRODORDCONF_CREATE_TE

    Hi everybody! I want to use the BAPI BAPI_PRODORDCONF_CREATE_TE to create confirmations for productionorders! I only use the recordtypes 'B10' and 'B40'. The problem is, that the  BAPI only creates partial confirmations, and no final confirmations. F

  • Material Management : Profit Center

    Hi All, I have got followin problem in inter company stock transfer using MM and SD: I am shipping Titalon-213 (Material) from 1000 (Manufacturing Company) to 1100 (Sales Company)  against P/O 4500062389.  The Outbound Delivery number created is 8094

  • I need to know if the last non beta version of firefox supports the google toolbar. I will only update firefox if that is the case!

    one month or two ago i was in NY at a friends house, and he updated firefox and in the new version what happened? "kaput" GOOGLE TOOLBAR GONE. There are features in GT that firefox does't provide. I won't live without GT. Therefore i will only update

  • Control reason in Movement types.

    Hi, in Inventory Management and Physical Inventory, Movement Types, Record Reason for Goods Movements, Control reason what is the difference between the selection of "." = entry in this field is optional and "blank" = entry in this field is optional

  • Precision of Number is 0?

    I used the sample from from http://www.oracle.com/technology/sample_code/tech/java/codesnippet/jdbc/OracleResultSetMetaData.html) to fetch metadata of a table, and the result is: Number of Columns in the table : 2 Column Name :SysIterID Column Type :