My hinges on my Mac are loose

It is slighly loose, and I know it won't be a big deal to fix. I'm just scared that it will cost a lot to repair. Any guesses? I'm going to apple tomorrow

Hi k,
Free "genius" bar appointments are usually held to 15 minutes or less, and I suspect that hinge tightening will take less than that. You may be pleasantly surprised, but no one here can say for sure. Good luck!

Similar Messages

All 30 minutes my Macs (iMac/Snow Leopard, MacMini/Lion) are loosing the connection to the Windows Servers (2 Networks: Home with Home Server 2011 (Server 2008) and Office with Home Server V1 (Server 2003)).

Hallo,
Ich betreibe im Büro und zu Hause jeweils einen Microsoft Home Server. In beiden Netzwerken ist neben diversen Windows Rechnern auch ein Mac vorhanden.
Die jeweilige "Konfiguration" ist wie folgt:
- Apple MacMini (Late 2011, als HTPC) mit Lion per Wlan über AVM Fritzbox 7390 an Microsoft Windows Home Server 2011 (Windows Server 2008).
- Apple iMac (Late 2010, Arbeitsplatzrechner) mit Snow Leopard per Lan über AVM Fritzbox 7270 an Microsoft Windows Home Server V1 (Windows Server 2003)
Alle Betriebssysteme sind auf aktuellem Stand.
Die Fritzboxen laufen mit der jeweils aktuellen Firmware
Nun zu dem Problem:
Beide Macs unterbrechen ca. alle 30 min den Kontakt zum Server. Die Verbindung wird zwar ca. 1-2 Minute später wieder aufgebaut, aber am MacMini (HTPC) macht sich dadurch bemerkbar, daß der Film oder die Musik für obige Zeitspanne stoppt und danach weiterläuft. Beim iMac (Arbeitsrechner) kann ein zuvor vom Server geladenes Dokument dann nicht mehr gespeichert oder gedruckt werden.
Der MacMini hat dieses Phänomen direkt bei der Verbindung mit dem WHS gezeigt. Der iMac hat jedoch zuvor ca. 1,5 Jahre ohne Probleme funktioniert. Dieses Problem tritt bei dem iMac (Snow Leopard) erst seit ca. 6-9 Monate auf.
Da unterschiedliche WHS und OS X Versionen betroffen sind und auch unterschiedliche Fritzboxen verwendet werden und scheint ein allgemeines Problem im Zusammenspiel Windows/OS X vorzuliegen.
Bei dem iMac fällt der genaue Zeitpunkt der Verbindungsunterbrechung nicht auf.
Bei dem MacMini läßt sich der Zeitpunkt dagegen relativ leicht bestimmen. Aus der Ereignisanzeige beim Windows Server ergibt sich leider kein eindeutiges Fehlerbild. Zu dem jeweiligen Zeitpunkt taucht aber relativ oft, aber nicht immer (!), in "Windows-Protokolle Sicherheit" der Fehler 4625 ("Fehler beim Anmelden eines Kontos") auf. Dies würde auf eine Rechteproblematik hindeuten. Das Konto des Mac kann aber alles was ihm auf dem WHS erlaubt ist.
Beim Suchen nach einer Lösung (bisher leider erfolglos) bin ich u.a. auch über das Problem des Server Infrastructure License Services (silsvc) beim Windows Small Business Server 2011 Essentials gestolpert (auch alle 30 min!). Vielleicht ein Zusammenhang?
Hello,
I run the office and at home each a Microsoft Home Server. In both networks, in addition to various Windows computers, a Mac is available.
The particular "configuration" is as follows:
- Apple MacMini (Late 2011, as HTPC) with Lion via wifi via AVM Fritzbox 7390 to Microsoft Windows Home Server 2011 (Windows Server 2008).
- Apple iMac (Late 2010, desktop PC) with Snow Leopard by Lan on AVM Fritzbox 7270 on Microsoft Windows Home Server V1 (Windows Server 2003)
All operating systems on current conditions with all patches and updates.
The Fritz boxes running with the latest firmware
Now to the problem:
Both Macs are loosing every 30 minutes the contact to the server. The connection is "re-"established about 1-2 minutes later. On MacMini (HTPC), the film or music is stopped for the above period. Thereafter, the film / music goes on. With the iMac (workstation) a document loaded from the server can no longer be saved or printed.
The MacMini has shown this phenomenon directly in connection with the WHS. However, the iMac has been working about 1.5 years with no problems. This problem only occurs for about 6-9 months
Because of different WHS and OS X versions are affected and also different Fritz boxes are used and it seems to be a general problem in the interplay Windows / OS X to be present.
When the iMac is the exact date of disconnection does not occur.
With the Mac Mini, the time can however be determined relatively easily. From the Event Viewer on Windows Server is unfortunately no clear error image. At the particular time but appeared relatively often, but not always (!) In Windows Security Logs the error 4625 (Failed to log on an account) on. This would indicate a rights issue.
Searching for a solution (so far unsuccessfully, unfortunately), I stumbled over the problem of the Server Infrastructure License Services (silsvc) in Windows Small Business Server 2011 Essentials (every 30 min!). Maybe a connection?

Hi, and thank you for your reply!
My reason for not posting this in the server forum is that I suspect it is a clien issue. All my other clients connect happily to the server which leads me to believe the server is configured correctly.
Only my the two MacBook Pro's are having problems.

Hinge on Satellite M30 is loose

The right hinge on my M 30 is to loose. I have tryed to dismantle the keyboard without succes, what to do?

Hi there,
the problem is that you cannot repair it only by tighten some screws. If the hinge on this model is loose then you will need new hinges and to exchange them, the whole machine must be disassembled since the hinges are partially under the palm rest and on the lcd installed.
So, if you want to fix that you should search for an technician which can fix it. Better solution would be to contact an authorized service partner:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT
Good luck

HT204291 Airplay mirroring. Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions

Airplay mirroring.
Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions.
Firewall set correctly (allow incoming...)
When I click mirroring to turn it on, teh Apple TV screen goes blank (from its home setting)
Any help appreciated.

Hi!
I figured it out! It was a firewall issue.
I use Handsoff and I checked it before i wrote here. There was no "user defined rule" that denied the communication but when i changed to "All rules" the program displayed several rules regarding AppleTV and its IP.
So if anybody has the same problem make sure you see all rules of your firewall and get rid of the AppleTV related rules generated by the program itself. You dont need to update to the latest iOS on the AppleTV!
I hope that I can help some people with this info to fix the problem.

I am going to buy either a Mac Air or Mac Pro Retina 8GB RAM and 256GB. And as I have to still run Windows I will install Parallels 9. As the Mac are both 64bit machines does that mean I need to install Windows 7 64bit ? And office pro 2013 64 bit too?

I am going to buy either a Mac Air or Mac Pro Retina 8GB RAM and 256GB. And as I have to still run Windows programs I will install Parallels 9. As the Mac are both 64bit machines does that mean I need to install Windows 7 64bit or just install 32 bit? (Going with Win7 as I hate Win8). And I will install Office Pro 2013 64 bit too or 32 bit or is that automatically selected by the underlying OS (I use Word, Excel and Access mainly for a membership database of a local club) ? I am not a power user so would appreciate advice on way to go

Again thank you. If I only use word, excel and access in the Win environment and Mac OS for email and safari for internet do I need anti virus software . Ie my connection to the world is mac only and I use office pro only to ruin the club, newsletters, membership database etc. and of course anything I do there can drag/drop to the mac environ to email. That's my understanding anyway. Next will my existing .pst file copy directly into mac mail or do I have to runs translator as I recall reading something about that ages ago when I started thinking Mac

How should I best import HD Videos from the new iPad to my mac without loosing video quality?

The new HD video on the new iPad is awesome, but it can eat up a lot of memory in no time. I would like to know what is the most recommended way to export my ipad movies to iLife on my mac without loosing image quality, so i can free up space on my iPad.
If I use iPhoto I notice that the file size of the video from the new iPad is a lot smaller then if I use iMovie to import the same video.
Example: I import a 53 second video from the new iPad to iPhoto and the imported file has a file size of 143 MB in iPhoto. (iphoto save the video as IMG_0048.mov)
I import the same video to iMovie manually and the imported file size is 843 MB in iMovie. BIG DIFFERENCE. (iMovie saves that same video as clip-2012-03-20 16;13;08.mov)
Now to really be confusing: I go to Image Capture program and locate the file manually on my iPad and is has the same name and file size is what is in iPhoto.
So either iMovie is making the File a lot larger when it imports to an event, or the file I'm looking at is actually the iPhoto version that I get because I sync with iPhoto.
The second issue that I have is that now I have 2 videos on my hard drive: one in iPhoto, and one in iMovie for a combined data storage of close to 1 GB.
I would like to be able to import ALL my iPad recording into iPhoto and then delete the video from the device when done.
But if I loose video quality, I'm not happy about that. Secondly, by importing video from my iPad into multiple iLife programs, I'm creating duplicates with sometimes different quality. Any suggestions? is there a setting in iPhoto that can do all this for me?
Robert

Don't use iphoto to deal with movies. it's not really meant for that. use Quicktime or iMovie to work with your videos

Sync between MacBookPro and iPhone 3G does not sync properly. Calendars duplicate events but worse is that only contacts from Address book from letter T onwards sync. Any contacts on iPhone which are not on Mac are lost during sync.

Sync between MacBookPro and iPhone 3G does not sync properly. Calendars duplicate events but worse is that only contacts from Address book from letter T onwards sync. Any contacts on iPhone which are not on Mac are lost during sync.
Solutions?

No, I never really found an easy solution. I believe it is an issue with some corruption in the iTunes database on the specific device. In my case, both my iPad and iPhone now show duplicate stream songs if viewed through iTunes on my Mac, but they show different songs. A couple years ago I had a similar issue on my iPhone, and Apple support suggested I back up the phone, completely reset it, and then restore it from the backup. It did work, so I imagine it would probably work for my current issues with the iPhone and iPad. But resetting and restoring an iPad or iPhone always makes me a little nervous that something will get lost. When I did reset/restore the iPhone, I do have to say, the restore process was 100% perfect and I did not lose any data at all even though Apple support said I might. If you try to go that route, I would suggest backing the device up both to a computer through iTunes, and to the iCloud so that you have a double backup.
None of this really resolves the issue with how the iTunes databases are becoming corrupted on the apple devices though, so it is very likely to happen again until they fix it. I have been unable to determine if there were any specific actions or conditions which caused the corruption to happen in the first place.
Might be worth another call to Apple support, or dropping in the local Apple store if you have one near by.

I want to upgrade my phone to the 4 or 4s. My macs are still running Tiger. If I bought an iPad 2, could I sync everything to it from the 4 without using a Mac at all, and then be able to iCloud my calendar and contacts, etc?

I want to upgrade my phone to the 4 or 4s. My macs are still running Tiger. If I bought an iPad 2, could I sync everything to it from the 4 without using a Mac at all, and then be able to iCloud my calendar and contacts, etc?

Radiation Mac wrote:
And you must be using a recent version of iTunes on your iMac in order to activate the iPad, So, no.
You don't need a computer to activate a new iOS device anymore. Anything with iOS 5 can be activated over a WiFi network (or cellular if that applies).

EMail on my iPhone 4s is no longer synching right with my Mac. Things I delete on my Mac are still on my iPhone. HELP! Deleting in both places is so time consuming. It has worked until recently...not sure what changed!

Things I delete on my Mac are still on my iPhone. HELP! Deleting in both places is so time consuming. It has worked until recently...not sure what changed!

Your email provider may have changed certain settings to do with deleting from server when deleting from client so that it no longer works. Are you using pop or imap? If pop then recreate the account using imap.

TS4001 Bookmarks are not syncing to ONE of my Macs, but showing up on other Mac (work), iPhone 4 and iPad 1. Macs are on Mountain Lion. Tried all of Apple's suggestions - and the one Mac is still not updating/syncing Bookmarks or Reading List. What's goin

Bookmarks are not syncing to ONE of my Macs, but showing up on other Mac (work), iPhone 4 and iPad 1. Macs are on Mountain Lion. Tried all of Apple's suggestions - and the one Mac is still not updating/syncing Bookmarks or Reading List. What's going on? Do I have to wait to OS update? It seems lots of peolple were having issues before ML, but I as fine. Since ML, I am having all kinds of issues!

Yeah, I literally have tried everything except deleting my iCloud account (I'm close, but that would require so many changes that it is way too painful to consider at this point).
I am still waiting to hear back from Apple Support. Hopefully something can be done, or they can do a reset on their end.
Thanks for taking the time to respond though, much appreciated!

Re: Connecting though internet when client Macs are on office network

I have a small company with two iMacs at work which are on a network with several other PC's. I have a home office with a Power Mac G5 (not intel based) and a satellite office 1500 miles away in PHX with a MacBook (brand new). I am trying to be able to access and control my main office computers using Apple Remote Desktop.
When I am at the main office with the MacBook and connected to the internet in the office I can use the ARD to control the two iMacs. But when I go home or down to Phoenix I cannot.
I have searched the forums high and low, but I must be computer illiterate. I cannot understand how to make it work. I assume there are some firewalls in the main office? Please help!!!

To be able to connect to a workstation from outside it's network, the ports that ARD uses must be open on both ends of the connection. ARD uses ports 3293 and 5900 so those must be open.
If your workstations get their addresses from an NAT device rather than being "real", the ports also need to be forwarded in the router to the workstation's internal IP address. ARD uses port 3283 for the reporting and updating function, so if your Macs are getting their IP addresses through NAT, since you can only forward a port to a single workstation, you can only get reports, push package/files to etc. for a single workstation.
ARD uses the VNC protocol for observation and control, though, and there are a range of IP addresses for that protocol, starting with 5900. ARD uses 5900 by default, so that port would be forwarded to the first workstation. You would, I believe, need to install VNC servers on the systems (since the ARD client cannot listen on any port other than 5900 while VNC servers can be set for other ports such as 5901, 5902, etc. You would then forward 5901 to the second workstation (and on to 5902, 5903, etc.). You can then use the following information:
Remote Desktop 2: How to specify a port number for a VNC client
to connect.
The only other options are: 1) to run the ARD administrator on a workstation on the network, and then take control of that system from outside, either via VNC or another copy of ARD, or 2) set up a virtual private network (VPN) so that when you connect from outside, your admin system is officially part of the local network.
Hope this helps.

How can I download video from a Canon ZR30 video camera to my IMac. I bought Elgato Video Capture, but the connections do not match. There is no white female end in the camera. Also, the red and yellow connections are loose at the camera end.

How can I download video from a Canon ZR30 video camera to my IMac? I have Elgato Video Capture, but the provided connectors are loose in the camera and the camera does not have a white female end. No signal shows up on the computer when I connect the red and yellow connectors.

Broken solder joints on the camera me thinks!!
sorry

I have always heard that Macs are less likely to get infected with a virus. My computer has been running much slower since I installed Maverick. Just not sure what the problem might be. Is there a way for me to run a diagnosis?

I have always heard that Macs are less likely to get infected with a virus. My computer has been running much slower since I installed Maverick. Just not sure what the problem might be. Is there a way for me to run a diagnosis?

Some have found relief just by reinstalling, but it is more than likely incompatible third-party applications that slow it down.
You will have to investigate to see what it is.
Open Activity Monitor and see if anything is using a lot of CPU% or Memory. If they are, check to see if there is an update for them.
Another place to look is the Console. See if anything is logging repeating messages with throttling and/or respawn in the All Messages list.
Sometimes it is not that easy to root out the problems, but if you have anything that purported to clean, protect, optimize, maintain, or flush your system, then that is likely the cause.

How can i format my external hard drive to write files from Mac without loosing the files that i alredy have on my external hard when i used it with windows?

How can i format my external hard drive to write files from Mac without loosing the files that i alredy have on my external hard when i used it with windows?
I have been using Windows to write files to my 1TB WD external hard drive and I do not want to format to loose the files capacity of around 500GB
Someone, Please help

Hi Allen,
Is there any way to store the back up to Mac and restore after formating?

IF UPDATES TO APPS THAT CAME WITH OUR MAC ARE FREE, WHY DOES APPLE REQUIRE BILLING INFORMATION TO BE COMPLETED IN THE SCREEN JUST BEFORE ACCESS TO INSTALLING FREE UPDATES???

IF UPDATES TO APPS THAT CAME WITH OUR MAC ARE FREE, WHY DOES APPLE REQUIRE BILLING INFORMATION TO BE COMPLETED IN THE SCREEN JUST BEFORE ACCESS TO INSTALLING FREE UPDATES???

It is necessary to confirm your identity as the 'buyer'. Please do not use all capital letters. It is not well regarded here and can be tricky to read for some. Thank you.

My hinges on my Mac are loose

Similar Messages

Maybe you are looking for