My HP DC7100 won't start, flashing red light 5 times?

My HP-DC7100 won't start up and it when I turn it on it flashes the red light 5 times, I looked it up and it apparently meant that it was a memory error, now I thought that was kind of weird because the RAM's were working just fine before this incident. Although this was straight after I done something, the case wasn't on properly and I pushed it into place and then the screen went fuzzy and it automatically turned off. Then I tried to start it up and now it flashes red 5 times, and I haven't even installed any additional rams, these are the RAM's that came with it. Please help!
Anyone??
This question was solved.
View Solution.

Try clearing the CMOS and see if that helps.
http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c00189283/c00189283.pdf
See pages B-3 and B-4.
It is possible you wrecked the PC by whatever you did here..."Although this was straight after I done something, the case wasn't on properly, and I pushed it into place and then the screen went fuzzy and it automatically turned off."
That ain't good...

Similar Messages

My Curve won't turn on and no sign of flashing red light

Hi!
I m all new to this blackberry forum thing....anyway i have a blackberry curve and all of a sudden yesterday it just stopped working. when i looked at the phone the screen was all white so i took out the battery and put it back on thinking that it will come back up but it didnt. Then i took the battery out again and plugged it to the USB(without the battery) because ususally it comes back up, but it still didnt. i put the battery again and plugged it to the USB thinking that it needs to charge but still no since of that flashing red light. I took the battery out and put my friends battery (cos he has a curve too) but still it didnt work. I did try holding down the power (red)button still not back on.
I just dont understand whats wrong with it, its not like i dropped it in the water or dropped it on the floor. I didnt do anything to it. It just stopped working.
Im really frustrated right now...I just dont know what to do..i hope someone can help me
THanks!

I finally got my curve to work. I just left it on the charger for a while and then it powered up. It seems if its a little low on power and I don't charge it relatively soon it shuts down and won't power up for awhile. I've also updated the software and cleaned out the junk files. It seems to be working fine now, go figure.
tm

Curve wont start and red light flashes

I was on my way home on the train and running low on batteries, but thought i had enough to quickly browse the applications.
I'd installed the free Time app earlier that day and checked it out, and it wasnt really to my taste, so I decided to delete the app. It warned me the blackberry would need to restart which was fine, only it turned off and didnt come back on.
I thought it had just ran out of battery but now after four hours of charging, and plugging it to my PC the blackberry still wont start. My laptop wont even recognise its plugged into anything and every button I press just gets the flashing red light.
Can anyone help? Is there a manual reset button on the device?

Hello,
I had this happen one time to my 8530... and I thought my heart was going to break. I'm an engineer so I have a bad habit of breaking and fixing, as I have learned that it's the best way to become an expert on any given piece of technology...
Anyway, I was able to fix my Berry by attaching it to my Mac, and letting the computer load the OS on it. Make sure it's plugged in with the desktop manager when you boot the phone your desktop manager should prompt you if you want to reload the OS...
Basically that's what the flashing red light means... you corrupted your OS, and now needs a reinstall.
It takes about an hour to do...
Hope this helps!
~Tom
~Tom
Curve 8530

Bold 9930 - dead and flashing red light

Bold - Verizon 9930, died with flashing red light, non-responsive. Can connect wtih loader, re-loading latest OS for Verizon (7.1.0_rel1737_PL5.1.0.429_A7.1.0.580_Verizon_Wireless) Load fails with "application loader was unable to connect with your device" when it tries to connect with the JVM. I have tried:- fully charged known good battery (tested in another 9930)- wiping device- start without battery, insert battery when JVM message comes up- both BB desktop and Loader directly- two different PCs (no change)- different USB ports- older version of BB OS for device- many, many iterations... All end with "application loader was unable to connect with your device" Is the device scrap? If so why? It's not even 2 years old, out of warranty, and apparently now totally worthless. This one is the CEO's Blackberry, and he's not happy... If I can't resolve this, it will be the very last BB to ever see the inside of our company. This is the second 9930 to die this way in the last 4 weeks.

Hello,
Firstly...
truckin-on wrote:
Does RIM care about these failure issues at all I wonder?
If you were hoping for a response from RIM, you have misunderstood the purpose of these forums. These are not a channel for any communications with, support from, nor escalation to RIM for anything. Rather, these are a user-to-user community of volunteers trying to help each other out amidst their own busy lives. So patience perhaps would be a good thing to have...
Nevertheless, please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
While you've already validated that your battery is good, I don't think you've tried the first part of this test:
Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem.
While perhaps redundant to what you've already attempted, here are a few more things to try:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
Since you are out of warranty, your next step I suppose would be to seek in-hand support from a qualified technician to give you a proper diagnosis. Doing such at this internet distance is quite a challenge and therefore cannot replace in-hand evaluation and diagnosis.
Good luck and let us know!

Flashing Red Light Quit Working

My flashing red light on the front of my 8350i has stopped working. You know, the one to notify you you've missed a call or have an unread email, etc. I've only had it about 2 weeks & was working fine until Friday. It quit working so I took the battery out & put it back in - nothing. Tried again on Saturday morning when it still wasn't working & it started working again...for a while. Now it's not working again. Haven't called tech support yet - anyone have any suggestions?

Do you have set in the Profiles for your active profile "LED notifications" to ON?
Does your signal coverage indicator blink green? Options > Screen/keyboard.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Flashing red Light on Photosmart D5160

I have a 3-4 year old Photosmart which know suddenly comes with flashing red light when i try to print.
In the display it says ERR and there are two commas or something on the bottom right. It does not match any of the problems which i can find on hp's pages.
I received an error message on my computer when trying to print - saying something like : do not recognize usb (code 043) Port_#003 Hub_#0003.
Can anyone help me out?
espen

Hi,
Flashing amber LED does not always point to fault. Please see this bug related to system
LED flashing amber.
CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
Status: NEW
Symptom: The appliance hardware has a "System health LED" that may go into amber status,
to indicate a hardware warning, and red to indicate a hardware failure.
Conditions:
In most situation the ACS appliance is still operative, when the light is in amber status.
The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
.Workaround:
-Reload appliance
-Verify enviromental conditions (temperature, power)
Alternate Details:
Symptom:
The appliance hardware has a "System health LED" that may go into amber status, to
indicate a hardware warning, and red to indicate a hardware failure
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
ugId=CSCsh44884
Let me know if you have any question.
Regards,
~JG
Do rate helpful posts

Flashing red light on my ACS 4.1

Hello, I have a flashing red light on my ACS. I have searched on Cisco.com to see what this meant and how I can fix it. I am aware that it is a critical error on the system health for my ACS. But what exactly does that mean? How can I figure out what is the problem before it becomes a big issue. Any help is well appreciated! Thanks!!

Hi,
Flashing amber LED does not always point to fault. Please see this bug related to system
LED flashing amber.
CSCsh44884 Bug Details : Appliance: No Troubleshooting for System health LED
Status: NEW
Symptom: The appliance hardware has a "System health LED" that may go into amber status,
to indicate a hardware warning, and red to indicate a hardware failure.
Conditions:
In most situation the ACS appliance is still operative, when the light is in amber status.
The appliance should offer better information on what condition caused this alarm, and include this either by new CLI command, or included as additional information in pakage.cab file.
.Workaround:
-Reload appliance
-Verify enviromental conditions (temperature, power)
Alternate Details:
Symptom:
The appliance hardware has a "System health LED" that may go into amber status, to
indicate a hardware warning, and red to indicate a hardware failure
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&b
ugId=CSCsh44884
Let me know if you have any question.
Regards,
~JG
Do rate helpful posts

8800 upgrade attempt lost usage and flashing red light. No response.

Thought I'd upgrade from 4.5.011 to 4.5.018, at the suggestion of the desktop manager. Things were okay until it stopped. Fatal error message, flashing red light...nothing else. Attempted again, and again. Gentleman at BB store did the same thing. He thinks it's unrecoverable.
I've tried an overnight battery pull, apploader attempt through C and D drives, Problems with applications and software (exe v axl...) Other ideas?
lrbwiner

John_Clark wrote:
Try this:
http://www.blackberryfaq.com/index.php/How_do_I_wipe_the_BlackBerry_using_Jl_Cmder%3F
if that doesn't work then try this:
http://www.blackberryfaq.com/index.php/What_to_do_next_if_Jl_Cmder_will_not_connect_and_wipe
Then use Loader.exe to reload the OS to your device using the instruction found here:
http://www.blackberryforums.com/general-8800-series-discussion/220178-latest-os-8800-4-5-0-312-4-5-0...
I've tried it 3 times. The program erases the application and then begins loading, which gets about 20% of the way and then stops. Message is communications failure A:0x0000000E. And the red light, which was out while the process was running, comes back on. 2 flashes, stop, 2 repeat.
Point of info. The screen never came on during the erase.
I will keep trying...thanks.
lrbwiner

Large outside Junction/Control box has flashing red light - bad or normal?

There is a Verizon outside box that is large with a flashing red light on its side. It appears to be a junction or control box mounted on the ground. It has been there for years and I do not remember seeing a flashing red light until now. Plus, my DSL connection has been dropping recently. Can a tech rep from Verizon High Speed Internet answer? Thank you for yur patience.
Solved!
Go to Solution.

These boxes are called Remote Terminals, and yes it is for DSL. The flashing light probably means that the battery backup has failed, so it shouldn't really affect your DSL unless your power goes out. And even then, the battery backup is only to power the voice line to make calls.
I would call 1-800-VERIZON and choose the option about "repair." I've had luck with getting poles replaced/repaired that way. Say that there's a flashing red light on the remote terminal, give the street address, and also give the central office you're out of (IE, your area code and first 3 digits of your phone number should tell the rep where you are). Also, stop by it and see if you can find any writing/markings on that, and tell them that too. Be as specific as possible. Make sure you get a ticket number from them, and make sure they have a call back number.
There was a tree laying on a wire near me, and I made sure I got a repair ticket; the next day a tech called me to say he was headed out that way and asked specific details about the location, what was wrong, etc. A few days later the tree was gone.

My ipod shuffle 2nd gen suddenly stops playing music after 15-20 mins.First it flashes green light and then flashes red light rapidly. Any solution to this ?

My ipod shuffle 2nd gen suddenly stops playing music after 15-20 mins.First it flashes green light and then flashes red light rapidly. Any solution to this ?

A 2nd gen shuffle is about six year old at this point. The likely cause is a battery that is worn out, with greatly reduced capacity or inability to hold a charge. The initial green light shows a good charge. The red light means the battery is drained.
Since the shuffle still appears in iTunes, you can try doing a Restore in case the cause is related to corrupted software on the shuffle. The Restore button is on the shuffle's Settings screen in iTunes. This will erase the shuffle, re-install its software, and set it to default settings.
Also, when the light becomes red and the shuffle stops playing, try turning OFF the shuffle for at least ten seconds. Then, turn it back ON. This resets the shuffle. Does it play again? If it does, let it play until it no longer plays again. Repeat turning it OFF and ON until it no longer plays. Then, connect it to power and charge it to full. See if that makes any difference.
If that does not help, the solution is to replace the battery. If you have a repair shop do it, the cost is probably uneconomical, compared to the cost of a brand new 4th gen shuffle ($50) that has more features, and a new set of headphones, plus a one-year warranty.
If you are good at such things, this web site has repair guides
http://www.ifixit.com/Device/iPod_Shuffle

Won't start -- five red-flashes sequence

My PlayBook worked just fine until last evening. Battery life was good; with no start-up or play issues. Original model; has worked well for nearly 3 years. Has latest OS. Never been dropped or abused in any way.
Last night it wouldn't wake up. I did a hard reboot (power button for 15 seconds) and then it seemed to start, but when the GUI came up the screen was insensitive: no reaction to touch anywhere. I then did a hard reset (both volume buttons plus power button), and now all I can get is a five-red-flashes sequence: flash pause flash flash flash pause flash -- longer pause, then repeat.
I had the BlackBerry charger plugged in overnight... no change, still get the five-red-flashes. Tried another hard reset, same result.
Any help would be appreciated! Thanks.
Solved!
Go to Solution.

Yasminm wrote:
Hello... I started to upI date my OS yesterday when I got the prompt of a new OS - I did over wifi on the phone, the phone died and I couldn't turn it on anymore and their was the rapid fast red light that keeps happening. I put the phone on the charger and still today that light is going on and the phone still doesn't turn on. I tried to update the OS via PC today and it got to 98% and said it can't go further. Please help!
you do realize this is the playbook area
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Won't boot only red light flashing

My BB Z10 unable to boot or charge once the battery all used up.
When I plug to wall or PC, only red light flashing.
Sent for repair twice, just return with a full charged battery device.
Once I used all the battery it won't charge.
I have to recharge the battery before it's all gone,
Or you have to follow the steps to reinstall the OS make it charge again.
Does it make sense? Will you accept that?
Means if I did not charge my Z10 before battery all gone, I have to do the OS recovery and ALL THE DATA GONE.

Hey panda1111,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Follow the steps below to try and bring the BlackBerry Z10 back to life:
Ensure that BlackBerry Link is installed on the PC or Mac OS
Ensure the computer has an internet connection.
Launch the BlackBerry Link Software.
Note: A backup of the BlackBerry device should be tried before a reload.
Turn off the BlackBerry device. Make sure there are no flashing LEDs and that the LCD is not still being lit by the backlight. If there are any flashing LEDs, hold the power button for 15 seconds until the LEDs stop.
Connect the BlackBerry device to the computer.
When prompted with Cannot communicate with device, click Restore and then click yes allow the update to be downloaded and installed on the BlackBerry device.
If the restore button is not seen press the vertical dots in the lower right corner of BlackBerry Link and select disconnected device. Highlight the disconnected device you are working with and attempt steps 4 to 6 again.
If the issue still persists, then I suggest contacting your network service provider for repair options.
Let me know if you have any more questions.
Cheers.
VIA | ViciousFerret
http://supportforums.blackberry.com/t5/BlackBerry-Z10/BB-Z10-Died/m-p/2230087#M10125
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

Torch 9860 wont start, no flashing red light as well

the loading screen comes and hangs on about 80%, no red light flashing, it just sits on 80%, Please Help!!! I tried to update the device software with desktop loader, when the device is rebooted after installing it again sits on 80%
the destop loader come with a error message " unable to connect to the device"
Please Help!!!

Hello jvzaveri,
Welcome to the Blackberry Community,
As you said you tried to update the device software with desktop loader and The Desktop unable to Connect the device . I think you you have to use force detection of your device using application loader. Here is the Article of KB
which might be usefull to you How to Force the detection of Blackberry Smartphone using Application Loader .
There may be some software issue, try not to install too many apps ,install only that you really needs. Try it and let us Know.
Good Luck
Prince
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

Dual-Core G5 won't boot. Flashing Red Light.

Hey Guys, I've got a 2Ghz Dual-Core G5. It's stock other than 2gigs of ram and a SATA Seagate Barracuda in the second drive bay.
Every now and then (on a fairly regular basis) I'll try to boot up the computer, I do hear the fans going but the drives don't spin up as usual, there is no chime and I get a red light behind the front panel of the G5 flashing. It flashes 7 times. After the 7 flashes it just sits there and after about a minute the fans go into airplane taking off mode.
I've been on the phone with AppleCare twice. A PMU reset did (possibly coincidentally) bring the computer back once or twice but has proven ineffective since. Typically I can either try booting the computer 30 times and it eventually works or I'll just leave it alone for a couple hours and it will boot up when I try again.
Resetting the PRAM doesn't work nor does holding option on boot up. This says (at least) to me that the computer doesn't get far enough to even look at the OS, the fault seems to be a hardware issue. The keyboard and mouse never get buss power.
Anyway, as I said it'll usually work eventually but I haven't been able to get the G5 to boot at all for the past 5 hours. Anyone had any similar experience? At this point I'm thinking bad logic board? Any opinions?
Thanks!
2Ghz Dual-Core G5 Mac OS X (10.4.8)

Hi, and a Warm Welcome to Apple Discussions and the Power Mac G5 Forum!
Presumably it is one of the red LEDs shown here that is flashing
http://docs.info.apple.com/article.html?artnum=302527
The symptoms possibly don't qualify for this - but maybe with some persuasion...
http://www.apple.com/support/powermac/powersupply/repairextension/
You could try the Apple Hardware Test
http://www.thexlab.com/faqs/aht.html
or TechTool
https://support.apple.com/techtooldeluxe/main?id=dl
Presumably AppleCare suggested you take it in to the shop...?

MB Pro Won't Start Up, Strange Light From Audio Jack

Greetings Apple-users,
so my macbook pro won't start up. i was using garageband, and i think i may have overpowered my audio input jack, which might have been the cause of the kernel panic that happened. the grey sheet came over instructing me to shut the computer down, which i did.
i attempted to turn it back on, but now all i get in a popping sound instead of the startup chime, the sleep light is on (slightly maybe?) and a red light is emitting from my headphones jack. very strange. I've tried all the usual fixes, and to no avail. the guy on the phone from apple told me i should send it in for repair, but i'm in germany and not in a big rush to do that.
i'm just curious to what any of you might think is going on. from looking around, i know now the light has to do with the optical audio switch, but no playing around with a toothpick could get it to turn off (wasn't sure where the switch was, but nonetheless,,,). I haven't been able to boot up to the disk or anything.
also, if this means anything. when i plug in my external speakers i hear what sounds to me like a light phaser effect, like possibly out of garageband. a strange hiss. and when i plug in my amp to the input through its speaker output, i can hear it through my speakers.
it's all very strange, but i can't help but think that this isn't a hard drive failure or even the logic board. maybe just a short or something in the jack?
any ideas or suggestions you have would be great.
thanks,luke

The SAME thing happened to me this morning when i booted up....There was a reddish light coming from the side of the computer where the jack is. However, I have a powerbook so i am not sure what this is.
PB G4 1.67 15" Mac OS X (10.4.8)

My HP DC7100 won't start, flashing red light 5 times?

Similar Messages

Maybe you are looking for