My HP printer on the wireless network and I can not get it to print using my iPad

Any ideas on how to get my wireless printer to print using my iPad?

Trenton1 wrote:
Any ideas on how to get my wireless printer to print using my iPad?
Are you using an Airprint-capable printer? Is it on this list?
http://support.apple.com/kb/ht4356
If it is, have you updated your firmware. Most printers that say they can be used with Airprint need to have their firmware upgraded before they can actually print using Airprint. HP's support pages provide the FW downloads you will need.

Similar Messages

I have a Office Jet Pro 8500 printer and I can not get it to print 8x11 pictures keep getting 4x6.

Have all setting set for 8x11 paper and on final I only get picture to fill 1/4 of sheet. What needs to done to get full 8x11 prints

Hello mariamac80,
It sounds like you cannot print from your network printer on your MacBook. Printer issues can be a but tough to nail down, but I would recommend trying the troubleshooting in this article named:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Follow these steps until the issue is addressed:
Make sure that the printer is powered on, has ink / toner, and that there are no alerts on the printer’s control panel. Note: If you cannot clear an alert on the printer's control panel, stop here and check the printer's documentation or contact the manufacturer for support.
Ensure the printer is properly connected to a USB port on the Mac or AirPort base station / Time Capsule. If the printer is a network-capable printer, make sure that it is properly connected to your home network.
Use Software Update to find and install the latest available updates. If an update is installed, see if the issue persists.
Open the Print & Scan pane or Print & Fax (Snow Leopard) pane in System Preferences.
Delete the affected printer, then add the printer again.
If the issue persists, try these additional steps:
Reset the printing system, then add the printer again.
If the issue still persists, reset the printing system again. Download and install your printer's drivers. Then, add the printer again.
Contact the printer vendor or visit their website for further assistance.
Thank you for using Apple Support Communities.
Cheers,
Sterling

When I go into iTunes on my Mac is recently takes over the entire screen and I can not get rid of it. Is there a setting I can change to have it work the old way?

When I go into iTunes (the latest update) now, it takes over the entire screen is difficult to remove. Is there a setting I can change in it to have it behave the old way?

I presume you are runnning iTunes on either an OS X 10.7 or OS X 10.8 system. Move the cursor to the very top of the screen so that the menu bar appears, then click the blue box with the arrows at the very right corner of the menu bar, or press Shift-Command-F. That will switch iTunes back to a normal window, which it should then remember for future launches.
Regards.

My mac is stuck on the guest profile and I can not get it off

I cannot get off of the guest profile on my computer everytime I start the mac up. What is the problem?

I had the same problem. The only way I could fix it was by dropping by the Apple Store/Genius Bar.

Printer went offline after a print was interrupted and I can not get it to work again.

Printer had been set up and was working but a paper interruption stopped it and I can not get it to print or remove the offline setting

That will probably be because its their licence and will be registered to them..??
You won't be able to open CC files in CS2, that is to many versions back.

Why doesn't my MacBook Air see a connected printer on the wireless network?

For some reason my MacBook has come up with a case of the stupids. I have been able to print out to my Canon printer before, but now it doesn't see it. The printer is on our wireless network and can be seen by our iPad, and iMacs but doesn't appear on the MBAir. I have reinstalled the drivers, rebooted the system and when I go to the Preferences to look at the Printers/Scanners there is nothing there. Pressing the + button comes up with a screen with nothing in the default area. The Air is connected to the wireless network and operates fine with the internet and other operations.
What can I do to fix this?

Hello gregfrommi,
After reviewing your post, I have located an article that can help with printing in Yosemite. It contains a number of troubleshooting steps and helpful advice for the issue you are experiencing:
OS X Yosemite: Printing troubleshooting
Check the network
Open Network Diagnostics, then follow the instructions to make sure you’re connected to the network.
If you’re using a Wi-Fi network and there are multiple Wi-Fi networks available, your Mac and the printer might be on different networks. Open the Wi-Fi menu in the menu bar, then try choosing a different network.
To see if the printer you want to use is on the same network as your Mac, open Printers & Scanners preferences (choose Apple menu > System Preferences, then click Printers & Scanners), then click Add . If the printer doesn’t appear in the list of available printers, your Mac might be on a different network.
If you know the printer’s IP address (for example, 192.168.1.100), you can try adding it as an IP printer. For more information, see Add or remove a printer.
If your printer is connected to a Time Capsule or AirPort base station, disconnect your printer from the Time Capsule or base station, then reconnect it.
Make sure you have the latest software
Make sure you have the correct version of your printer’s software (also called its printer driver).
If you’re using a printer that another user is sharing, make sure you’re both using the same version of the printer software. To find out which version you’re using, open Printers & Scanners preferences (choose Apple menu > System Preferences, then click Printers & Scanners). Select the printer in Printers & Scanners preferences, click Options & Supplies, then click General. Note the driver version.
If you’re using a network printer or a printer attached to your Mac, make sure you have the latest version of the software for the printer. If you still have problems, try different printer software for your printer.
If you’re using an AirPrint-enabled printer, you can check with the manufacturer to see if there’s a firmware update for your printer model.
Replace a corrupted printer queue window
If none of the previous solutions work, the printer’s queue may be corrupted. Open Printers & Scanners preferences (choose Apple menu > System Preferences > Printer & Scanner preferences), then delete and set up your printer again.
If you still can’t print, reset the printing system.
Print documents
Reset the printing system
Add or remove a printer
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

What would cause an IMAC to recognize one printer on a wireless network and not recognize another printer?

What would cause an IMAC to recognize one printer on a wireless network and not another printer? I have a smaller HP and a an HP 4600. The computer recognizes the smaller printer but not the bigger printer even though the printer in Settings and shows up on Settings, but I cannot print to it.

Do you have a printer driver installed for it? When you open the Print dialog have you selected it from the Printer dropdown menu at the top of the dialog?
Do you know that the printer is working and is properly installed (Added?)

I have a networked HP L7780 all in one printer and I can not get it to fax through my Macbook Pro. I have downloaded all the drivers and it has passed all the tests. Every time I try to fax it shows the job paused.

I have a networked HP L7780 all in one printer and I can not get it to fax through my Macbook Pro. I have downloaded all the drivers and it has passed all the tests. Every time I try to fax it shows the job paused. I can manually send and receive faxes but I can not do it through the computer.

Try deleting the printer, deleting the job queue and reinstalling the printer again.

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except join not extend and I can not get a network on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Rout/

Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
Airport gets it address DHCP.

Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
Note that the Express will not provide any additional wireless coverage when it "Joins".

Since I've upgraded to Maverick the airpot utility does not recognise that there is a time capsule on the wireless network. I can see the TC using the air port utility on my iPhone5 and on my iPad. What am I doing wrong on my macbook?

Since I've upgraded to Maverick on my Macbook Pro the airpot utility does not recognise that there is a time capsule on the wireless network. I can see the TC using the air port utility on my iPhone5 and on my iPad. What am I doing wrong on my macbook?

I have over 250G backed up and I really don't want to reset everything and start again.
Not sure what you mean here.
A reset will not affect any of the data on the Time Capsule hard drive. You would have to perform a completely separate and very deliberate Erase Disk operation for that to occur.
I'm not recommending that you perform a default reset, but it is an option if there is really nothing else to try.
I don't know if what you are seeing is a Mavericks issue or not, since I refuse to use any new software until at least the first major update with fixes comes along.
Another user may be able to offer more input on Mavericks.

HP Photoprinter C7280 printer. The wireless radio is on but not functioning - so no wifi conection.

HP Photoprinter C7280 printer. The wireless radio is on but not functioning - so am unable to gain wifi connection and print! - Why? How do I fix, Thanks

I would guess that the printer's wireless radio has died. Have you tried plugging the printer into your wireless router with an Ethernet cable? It should work and give you the same functions as wireless. Your computer or router will not care how the printer is connected.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

I want to reset (clean out) my old 4S. I have just bought a 6 and have the 4S as a stand alone unit (No connection to network. I can not get the sitcom to do the erase all command. It wants to access the Cloud which is impossible.

I want to reset (clean out) my old 4S. I have just bought a 6+ and have the 4S as a stand alone unit (No connection to network). I can not get the system to do the erase all command, it wants to access the Cloud which is impossible. Is there anyway to 'Erase All Content and Settings".

Something here might help a detailed list of actions
What to do before selling or giving away your iPhone, iPad, or iPod touch - Apple Support
refer to If you no longer have iPhone section

I have an hp office jet 4500 and os maverick 10.9.4 and I can't get it to print after last upgrade, multiple malfunctions and error, help?

I have an hp office jet 4500 and os maverick 10.9.4 and I can’t get it to print after last upgrade, multiple malfunctions and error, help? I have tried deleting and resetting printer and re-installing update 6 times. Last update attempt showed none available??? I can’t load the software directly from HP because their only option is to use the software update option on the mac....frustrated!!! Help!!
I get blank pages that just run through the printer and a stats window that just 33% complete and goes no further.

I am going on the guess that an old driver is still installed...
Use Finder Go > go to folder, and go to /Library/Printers and delete the HP folder(s).
Reset the Printing System:
OS X Mavericks: Reset the printing system
Now, Add the printer in Print & Scan prefs.

The air port on my imac went off and i can not get it to work

my air port on the imac weny off and i can not get it to work now

Apple used to use airport name for everything.. is this the internal wireless card?? Or external airport router?
If it is the internal wireless card, is it still listed in system profile.. and do a hardware test with your original CD.
See http://support.apple.com/kb/ht1509
The problems with Mavericks are very great.. if you upgrade installed anything can happen.. a common feature is the internal wireless card fails to work.
Give details and we can figure it out.
Here is discussion about the same thing as I think has happened to your imac in macbook.
https://discussions.apple.com/thread/5219345?tstart=30

I have an iPhone 4 and my lock button is jammed and I also can not touch anything on the left side of my screen well as any pop ups from the phone itself, so i can not get past the set up stage in reset process...how can i fix it/can it be fixed?

I have an iPhone 4 and my lock button is jammed and I also can not touch anything on the left side of my screen well as any pop ups from the phone itself, so i can not get past the set up stage in reset process...how can i fix it/can it be fixed?

Make an appointment at the genius bar and get the phone replaced.

My HP printer on the wireless network and I can not get it to print using my iPad

Similar Messages

Maybe you are looking for