My hp top shot laserjet pro m275 cannot find my wireless connection

Hi there,
my printer cannot find any wireless connection available.
and the blue light on the wifi icon is blinking.
how do I solve this problem so i can print again?

The blue wireless light flashing means you are not connected to your routers SSID. You need to go back and connect to your routers SSID with it's password to get the light on solid.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Similar Messages

C660-1lp Repeatedly drops or cannot find a wireless connection

we are a school and purchased 12 C660-1lp last summer these are causing constant problems by dropping or just not fining a wireless connection. This is only rectified by rebooting; sometimes multiple times
We have a number of other makes and models of laptops onsite and they have no problems.
We have XP installed on all devices with the latest drives and BIOS and we are using CISCO Aironet 1130AG access points
The problem we have is that there is no obvious fault but the issue affects all/only this model of laptop onsite and is rendering them unusable/unreliable
Could anyone please help
IanN

Satellite Pro C660-1LP (PSC0ME-01L00TEN)
This is the site for US machines, Ian. You might get better responses from the folks with your model.
Toshiba Support Forums in Europe
I wonder if you used Windows 7 things wouldn't be better. Have you investigated XP Mode? It's free. Wouldn't hurt to try that on one machine.
Windows XP Mode and Windows Virtual PC
-Jerry

Satellite Pro C660-1LP drops or cannot find a wireless connection

We are a school and purchased 12 Satellite C660-1LP last summer these are causing constant problems by dropping or just not fining a wireless connection.
This is only rectified by rebooting; sometimes multiple times
We have a number of other makes and models of laptops onsite and they have no problems.
We have XP installed on all devices with the latest drives and BIOS and we are using CISCO Aironet 1130AG access points
The problem we have is that there is no obvious fault but the issue affects all/only this model of laptop onsite and is rendering them unusable/unreliable
Could anyone please help
Ian Noble

Hmm did you also disable the power saving for WLan card?
This can be done in Win 7 Power Management.
Additionally disable the option Allow to turn off this device to save power. This option is placed in device manager Wlan card properties last tab (power management)

Pls take note that my IPad 3 used to find my printer HP wireless D110. The only thing that I did was to update to IOS 7. Do you think this is the reason why my iPad cannot find my wireless printer?

Pls take note that my IPad 3 used to find my printer HP wireless D110. The only thing that I did was to update to IOS 7. Do you think this is the reason why my iPad cannot find my wireless printer?

1. Turn the router, iPad and printer off
2. Turn on the router and then wait 30 seconds
3. Turn on printer and then wait 30 seconds
4. Turn on your iPad and test print.

Cannot find the Novell Connection Manager for LDAP

Novell Connection Manger for Java/LDAP
Cannot find the Novell Connection Manager for LDAP in download
I am trying to connect through a Java client to the Apache Directory Studio, LDAP server....I have downloaded the classes from the download page...see link below...but I can't see the NovellConnectionManager Class anywhere in this download when I use the open freely application to view the jar details.
LDAP Classes for Java
Environment: Windows 7

Hi MentalSuplex, and a warm welcome to the forums!
Don't know about Airport cards for it, but other options...
http://eshop.macsales.com/item/Sonnet%20Technology/N80211PCI/
Maybe this one, ask them...
http://eshop.macsales.com/item/Newer%20Technology/MXP802NPCI/
I use these...
http://eshop.macsales.com/item/Newer%20Technology/MXP2802NU2C/
http://eshop.macsales.com/item/Edimax/EW7711UMN/

Equium L300: cannot get a wireless connection

Hi all
I purchased an Equium L300 PSLB2E and cannot get a wireless connection. I have checked the network adapters and it tells me the Realtek RTL8102E Family PCI-E Fast Ethernet NIC ( NDIS 6.0 ) is working.
I have tried the FN+F8 but do not get any symbol for Wi Fi.
I have the Wireless switch to the fornt of the unit switched on.
Any help much appreciated.

Try again!
If the WLan card (device) will not appear in the Network adapters then you should take your Recovery DVD and should set the notebook back to the factory settings.
By the way; there is a Toshiba tool called *WPS Library*.
The WPS Library is needed for using ConfigFree and wireless connection.
Try to reinstall it too.
Good luck

I am in an internet cafe and my macbook pro can't find the wireless network available here. I have used this network before. I have restarted my machine several times too. help please

I am in an internet cafe and my macbook pro can't find the wireless network available at the cafe. I have used this network before. I have restarted my machine several times too. help please

Change your router channel. Sometimes this is all you will have to do.
Power cycling the router. Read the router's user manual or contact their tech support for instructions.
System Preferences/Internet & Network/Network
Unlock the padlock
Locations: Automatic
Highlight Airport
Click the Assist Me button
In the popup window click the Diagnostic button.
System Preferences/Network- Unlock padlock. Highlight Airport. Network Name-select your name. Click on the Advanced button. Airport/Preferred Networks-delete all that is not your network.
Place a check mark next to "Remember networks this computer has joined." Click the OK button and lock the padlock. Restart your computer.
http://support.apple.com/kb/TS1920 Mac OS: How to release and renew a DHCP lease
No internet connection (wireless)
Check to see if an extra entry is present in the DNS Tab for your wireless connection (System Preferences/Network/Airport/Advanced/DNS).
Delete all extra entries that you find.
Place a check mark next to "Remember networks this computer has joined."
Other resources to check into:
http://www.netspotapp.comNetspot
How to diagnose and resolve Wi-Fi slow-downs
Pv6 troubleshooting
Mac OS X 10.6 Help: Solving problems with connecting to the Internet
What Affects Wireless Internet?
Solutions for connecting to the Internet, setting up a small network, and troubleshooting

Airport Utility cannot find Apple Wireless Devices, yet I'm online!

I'm trying to enter in my SSID number for my kid's Wii to get it online, and I've tried to run through their tutorial. It tells me to go to Airport Utility and find my base station. Here's the deal, it says it cannot find my wireless device. And yet here I sit, complaining about it online.
How can I be online yet the computer not recognize it?

I finally just hooked up an ethernet connection and it works fine. I think the problem all along was the airport card in my iMac. I currently have my question about my airport card as a reply to another post from someone having a similar issue.

Cannot find tab to connect to internet with nokia ...

hi, i cannot connect to the internet, the book isnt clear, i,ve played around with phone but cannot find where i connect to put the internet password in

Better if you can be a bit detailed.
Are you trying to connect to internet using Wifi or Mobile Data?

Haelp! cannot print over wireless connection

I just set up a wireless network in our house, with a 2Wire 1701HG gateway (wifi plus ethernet.). I have a Brother neworkable laser printer, connected to the wireless router via an ethernet cable.
When I have my iBook also conected by ethernet cable, I can print, no problem. But when I am connected by wireless, when I try to print it always says "AppleTalk inactive," even though when I go to the the Network Preference panel it says it is active!
The long and the short of it is I cannot print via wireless connection. What do I need to do to remedy this situation?
Thank you!!!!

This snippet is from the Tiger printing help area. I had similar difficulties and it worked for me:
Delete and recreate the printer queue
1. Open Printer Setup Utility (10.3) or Print Center (10.2).
2. Delete any queues for the printer model you have.
3. Add a new queue, and choose Bonjour (formerly "Rendezvous"). It should locate and show the printer attached to the base station.
Good luck!

LaserJet Pro CP1525nw cannot connect to new router (Home Hub 2000)

In December, we replaced everything EXCEPT our LaserJet Pro CP1525nw colour printer - new laptop (Dell Inspirion 15), new operating system (Windows 8.1 - 64 bit), new internet provider (Bell) and new wireless router (Home Hub 2000).
Immediately, we were unable to connect to the router. We tried all of the suggestions, including connecting the printer directly to the router - which worked, until we disconnected it and then they could not communicate again.
At the time, the only solution we could find was to connect our printer and laptop via USB cable and print that way - no more wireless printing, so unable to print from phones and iPad, but at least we could print from the laptop.
In the past month, we have become unable to use many of the features on our printer - when we try to select print options, we get the message "HPMSN103.dll has stopped working." So, we can still print, but cannot select options.
We have tried using the CD that came with the printer, and it gets to a certain point and then a fatal error occurs. We have tried downloading the "full solution" printer install program from the HP website, and the same thing happens. We have tried skipping that and just choosing the appropriate printer driver in Windows: if we only use that driver, we get a printer that shows up, but we cannot print if we select it (interestingly, though, we can actually access the printer options!); if we say we have the disc, then we get two printers showing up - we can select print options on the one that will not allow us to print, but not on the one that actually prints. If we try removing one of the printers, they both uninstall and we're back to square one.
So, we WANT to be able to get back to printing wirelessly - after all, we paid (handsomely) for a wireless printer! And we still cannot get our printer and the router to recognize each other. Can somebody help? We don't want to have to buy another printer.
Thanks!

Hi @Capers2 ,
I see that you are experiencing issues setting up the printer on the new router. I will certainly do my best to help you.
Thank you for providing that detailed information.
If the network name has any spaces or special characters, the printer may not recognize it.
The printer is only capable of sending/receiving in the 2.4 ghz band.
If it is set to 5 GHZ network you may need to change to 2.4 ghz. (rename the 5 ghz or shut it off)
The WPA key setting needs to be on AES to work correctly not TKIP.
Multi casting needs to be turned on.
Firewall on router has to have open ports for printer.
If you have Mac Filtering you need to give printer hardware address from Configuration page.
You might need to contact your router company for further assistance to check those settings.
I would reset the printer first to clear out any previous network settings.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
Printing a Configuration Page.
The easiest way to setup the printer back on the wireless network is through a Ethernet connection and then switch over to wireless.
Disconnect the USB cable.
Remove any printer software by following these steps:
Go into Devices and Printers , click file then Server Properties, click on the Drivers tab at the top of print Server Properties window. Choose the printer you want to uninstall and click remove. Choose remove driver and package. Any that say Universal PCL 5 or Universal PCL 6 also remove and the Laserjet CP1525nw.
The next screen will give a warning, letting you know that deleting the driver package will remove it from the system. Click yes to say that you are sure you want to do this. (if the printer isn't listed that is OK)
Right click and delete any entries for the Laserjet in the Devices and Printers Window.
Run the uninstall from the CD.
Press the Windows key and the X key together. and select File Explorer, right click the CD for the
printer and left click open in new window.
Connect the printer to the router with a Ethernet cable.
Wait about 1 minute and the printer should have a valid IP address.
Print the configuration page to get the printer's IP address to configure the Wireless.
Type the IP address in Internet explorer's address bar which should open the printer's embedded web services page.
Setup the wireless through here now.
Click on the networking tab, wireless on the left, fill out the network information and apply the settings.
After the confirmation, then disconnect the Ethernet cable.
Now you should have a blue wireless light on the printer in about 1 minute.
Perform a clean boot on the computer and turn off the Antivirus Software. How to perform a clean boot in Windows.
Run the installation again.
If you are prompted to connect the USB cable during the installation, Then immediately after connecting the USB cable, follow the steps in this document to update the drivers so it doesn't error out. A Fatal Error Displays During Software Installation. Then the installation should continue.
Test the printer.
If there is anything else I can help you with, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Laserjet pro 100 cannot connect to wireless

Hi There,
I cannot connect my printer HP laserjet 100 color mfp m175nw to the wireless. It is connect to the router and it install on the computer with the Usb cable but not with the wireless connection.
How can I fix this?
Before it used to work perfect I could even print from my phone, now unless I connect my computer to the printer with cable it will not work because I cannot install the printer working with the wireless connection.
Please help
This question was solved.
View Solution.

Thanks for letting us know, glad you got it fixed
Although I am an HP employee, I am speaking for myself and not for HP.
Twitter: @Ciara_B_HP

VM created on Win 8.1 Pro Laptop cannot find win 7 iso file on USB

VM cannot find USB to load Win 7
I have a Windows laptop with Win 8.1 Pro installed. I turned on Hyper-V and created a VM. Everything worked up to that point. I also downloaded the Win 7 iso and placed it on a USB thumb drive. I also downloaded the Win 7 installer.
When I "start" the VM, I get a black screen with a message the VM could not load an OS.
It appears to me that the VM does not know where to look for the OS. I cannot find any way to tell it where to look.
I spent over $300 for upgrades to Win 8.1 Pro and a licensed copy of Win 7 so I could run Win 7 on my laptop as I need it to run UPK (which is not compatible with Win 8).
As a last resort I went to the Micrsoft store in Miami and offered to buy a Surface Pro 3 if they would install the VM and Win 7 on that for me. They said it was very easy to do and I would have no problems, etc., etc., etc. In other words they did not have
a clue about what I was talking about.
I hate to see over $3000 worth of hardware collecting dust on my closet shelf because I cannot use them. I am hopeful someone here can help a non-techie make this thing work.
Thanks in advance,
Dennis
PS - Went to the Apple store last night and was shown a MacBook Air with Parallels installed. It was running Apple stuff on the Apple OS and MS Office 365 on Win 7. It was all very seamless so am leaning very much to going with Apple as a solution.

You don't say that you attached the iso to the VM. The easiest way to do
that is to connect to the VM and then on the console, pull down the
"Media" menu, Select "Insert Disk", then browse to the ISO and select it.
Then under the "Action" menu, select "Reset".
You can also mount an iso in the settings for the VM.
Bob Comer

Hp laserjet Pro 200 M276nw won't consistently connect wirelessly with iMac

I'm on my second brand new hp laserjet Pro 200 M276nw in 3 days, it will not consistently connect wirelessly with my newly purchased (8days old) Apple refurbished 27" iMac on OSX 10.9, i7 chip & Fusion Drive. The hp laserjet will sometimes connect wirelessly immediately after clicking "print" on the iMac, but about half the time it says "printer not connected" & takes 2-4 minutes (or longer) before the devices do connect. I've called hp support many times, they're reset various things via remote takeover of my iMac, the printer will work for a few of minutes but then the same problem returns. AppleCare made sure I have the
correct Airprint driver installed & also checked my settings, but says they don't know why this is occurring. I've also verified that our newer (6 months old) AT&T router is functioning correctly.
My older hp laserjet (CM1312nfi MFP) has worked flawlessly since 2009 via USB connection with my old iMac (still on Snow Leopard), I assumed it would continue with the new one, but there is no software update for Mavericks & the scanning feature won't operate on the new iMac. Hp says it is a discontinued model. The new hp laserjet is a successor model to the older one, they are both very similar except for the new wireless feature.
I can print fast & wirelessly from the new iMac via a different new hp inkjet printer (8600 series) here in the house. This inkjet printer is less than a month old, I installed it myself for a Windows laptop here, it has never malfunctioned. Unfortunately it's upstairs & I do not like inkjet print quality, I need a good laserjet here in my office downstairs next to my iMac.

HI there
Did you manage to sort this issue out - as I have exactly the same problem.
Lots of similarities as I also have an inkjet 8600 which works via USB and wirelessly no problems at all!
I always buy HP printers as they are usually easy to set up - but this one is making me tear my hair out!
I've even upgraded to Yosemite and downloaded the new drivers from HP - no success. The printer will print one page and then become unavailable.
I can print via USB or wireless direct - but not just via my wireless network which is what I want to do!
No responses posted - so assume no one has a fix.
aaaargh!!!

HP LaserJet Pro 200 color MFP M276nw Wireless option is gone!!!

I have a HP LaserJet Pro 200 color MFP M276nw. The blue lit wireless icon used to stay on steady and all was fine for quite a while, then the Blue icon would start flashing like it lost it connection to the wireless router. I would just recycle the power on the printer and let it reboot. Usually it would connect with the router again but, it's been getting worse lately. I figured I would try to the latest firmware to the printer as maybe there was a clitch with the original firmware.........Well, now I get no blue wireless icon and the wireless menu disappeared from the touch screen. I tried to access the wireless settings in the web browser, the program said "this product does not support wireless connectivity.......WHAT?!!!!! I tried a "cold reset" on the printer to clear everything and still have no wireless option. I suppose its going to stick with the same firmware that was last installed. I did notice that the printer lists itself with an "N" at the end of the model # on any printed report instead of the "NW" its supposed to be. I did download the printer firmware from the Pro 200 color MFP M276nw support page. it's acting like it now has the firmware for the non-wireless version of this printer. This is the firmware I used
file name:
M276_colorMFP_Series_FW_Update-20140521.exe [1/1, 14.32M]
. Any Ideas how to fix this? Seems like this is the wrong firmware for this printer. Everything else appears to work ok.
Bob

****UPDATE**** After running a few copies through the printer the wireless feature showed up again. The printed reports started to show this printer with the "NW" at the end of the model number instead of just the "N". After a few minutes it all went away again. Seeing the correct model number show up for a few minutes made me believe the correct printer firmware is installed. To make this a short story, I ordered the wireless PCA assy (Small internal wireless circuit board, HP part #1150-7940) and replaced it. It's been working great for the past few days( since the board was replaced). Apparently, if the system does not see a working wireless board it defaults to the non-wireless model number and the wireless option disappears from the menu screen. The other thing is there apparently is no fault code that covers this type of failure.....frustrating, to say the least. I will update if this is not the fix but, it looks like I got it!
Thanks!!!!!!!
Bob

My hp top shot laserjet pro m275 cannot find my wireless connection

Similar Messages

Maybe you are looking for