My i phone is locked i cannot input my code
Hello Support Community,
after activating the speakcontrole. I cannot input my code anymore. You can see the numbers when you touch them nothing happens. Permanently a voice is talking to me!
I already made a restart and reset.
Unfortunately the SIM Card is also blocked. May this is a cause of two errors. I don't know!
Thanks for your help in advance
Birger
Press the Home Button 3 Times...
Similar Messages
-
my iphone screen is broken and i need to access it through itunes but my phone is locked. it cannot be unlocked on the screen but is there any way i can do it on itunes so i can access it?
Depends, if you've synced with this iTunes, while that passcode was enabled, you won't be prompted to enter the passcode when connecting your phone. If you have not synced, while that passcode was enabled, you will. So, if you fall in the later, there is no way to do what you want.
-
Phone is locked/disabled (cannot remember passcode) but cannot restore becasue itunes says i need to turn off find my phone on icloud but i can't get into my phone to do that, HELP
Follow the directions here to force the phone into recovery mode & restore it:
http://support.apple.com/kb/HT1808
This will remove the passcode. -
HT1918 cannot input security code for credit card
cannot input security code for credit card update
Where are you doing this? Go to your account in the Apple store and re-enter (not just verify) all of your account information and be sure one click ordering is on and try again
LN -
Restore needed on screen but iTunes says phone is locked and cannot connect
restore needed on screen but itunes says phone locked and cannot connect
now it says cannot restore from itunes (error 1)
-
I came across a 5th gen iPod touch at a bus stop, and tried but cannot activate it, as it is under the Find My Phone/ Activation Lock.
Since I do not know who the previous owner is, is it possible to get around this roadblock? Or is it just no good to try?There's no way to get around it. Turn it into the police so they can find the rightful owner. You won't be able to use it anyway.
-
HT4623 some how my phone got lock i cant rember the code 20 atemps so it lock it
i forgot my pass code and after 11 attemps the phone got restricted can some one help lease
See this support doc.
http://support.apple.com/kb/ht1212 -
HT201401 can i make calls while the phone is locked???
can i make a call while the home screen is locked?
And that is only if you set it up for Siri to work under the lock screen. In Settings, if you have a Passcode lock on and have Siri turned off for use when the phone is locked, you cannot use it. Just an observation.
-
My iPhone has been badly damaged and I cannot get the screen to work. I want to do a backup to transfer to my new phone but the backup will not work because the phone is locked. Can I input my lock code to the phone via the computer to allow a backup?
Sorry, no.
-
Phone is locked cannot activate it code forgotten
phone is locked cannot activate it code forgotten
Hello Hoppscotch,
Thank you for using Apple Support Communities.
For more information, take a look at:
iOS: Forgotten passcode or device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
Have a nice day,
Mario -
I recently had to restore my Iphone 4s and ever since I cannot double click the home button whilst the phone is locked and change my music. The controls come up and I can adjust the volume but I cannot change the songs. Help needed please!!
Have you guys been able to activate your iphone yet? I bought an iphone 4s from eBay and it worked fine, but the previous user had left some data on it, so last night I used the "erased all content and settings" to restore it to factory setting so I can start fresh and restore my backup. But now I'm stuck at the activation screen (I get the same "the activation server is temporarily unavailable") and can't get it to activate, even if I use my old deactivated AT&T sim card (I'm on straighttalk now).
I might try activating it with an active AT&T sim card from my fiancee's phone when she gets home, so I'll let you know how that works outs.
If it's true that the server is down; anyone know when it will be back up again? Thanks in advance.
iPhone 4s iOS 5.1.1 (9B206)
Carrier AT&T 12.0
Modem Firmware 2.0.12 -
I have a new phone, through AT&T insurance, and it does not recognize me as a developer until i register UDID. But the phone is locked and has never synced to Itunes so how the **** do I find the UDID number? This one is stumping me?
Ok next problem currently my MAC is with my daughter out of state, I only have a PC in the house...
-
HT1766 what do i do when my phone is locked and it says to connect to itunes?
what do i do when my phone is locked and it says to connect to itunes?
If You Are Locked Out Or Have Forgotten Your Passcode
iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
iOS- Understanding passcodes
If you have forgotten your Restrictions code, then follow the instructions
below but DO NOT restore any previous backup. If you do then you will
simply be restoring the old Restrictions code you have forgotten. This
same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
1. Verify that you are using the latest version of iTunes before attempting to update.
2. Connect your device to your computer.
3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
4. Select the Summary tab.
5. Select the Restore option.
6. When prompted to back up your settings before restoring, select the Back Up
option (see in the image below). If you have just backed up the device, it is not
necessary to create another.
7. Select the Restore option when iTunes prompts you (as long as you've backed up,
you should not have to worry about restoring your iOS device).
8. When the restore process has completed, the device restarts and displays the Apple
logo while starting up:
After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
iOS, keep your device connected until the "Connect to iTunes" screen goes away or
you see "iPhone is activated."
9. The final step is to restore your device from a previous backup.
If you can not restore your device then you will need to go to recovery mode.
Placing your device into recovery mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
red slider appears, then slide the slider. Wait for the device to turn off.
If you cannot turn off the device using the slider, press and hold the Sleep/Wake
and Home buttons at the same time. When the device turns off, release the Sleep/Wake
and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the device.
The device should turn on. Note: If you see the screen pictured below, let the device
charge for at least ten minutes to ensure that the battery has some charge, and then
start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
When this screen appears you can release the Home button.
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information. -
Inspection Lot Created but not shown in QE72, and cannot input result or UD
Hi Exports,
I have Inspection Lot Created by 04-production goods receive, but not shown in QE72, and cannot input result or UD
Inspection Lot status: CRTD CHCR SPRQ,
in Business Process of inspection lot showing:
*Cancel inspection lot
Assign RMA proc. to insp. lot
Assign notification to lot RMA
Batch log indicator required
Certificate missing
Change inspection lot
Change planned lot quantity
Choose task list for insp. lot
Confirm Receipt of Certificate
Create part. lot for insp. lot
Flag cancellation
Inventory posting required
Lock
Lot for process documentation
Lot reset allowed
What is going wrong?
BTW, the sampling procedure in Inspection Plan is a read-only field, but empty inside.
DanielDear in your case there is no Inspection plan was attached to the lot so attach the plan and make lot status to REL then only you can do Results Recording.
Inspection plan gets auto assigned to availble inspection plan on respective date if you enabled the inspction with tasklist and automatic assignment boxes in relevant inspection types in MM QM view for this Inspction plant should be made avaialble in stsyem before any lot created which can be created QP01.
If it is not getting assiged automatically then you can assign it manually by QA02 here go to inspection specification tab click on Task list assignment the go to sample tab and click on sample and SAVE Inspection plan will be attached to inspection plan.
Once inspection plan is the lot status you can see REL before assignment of a plant it would be CRTD.
Cheers
KK -
I have turned off Siri's access when my phone is locked, but it isn't working!!
I have followed the instructions for turning off Siri when the phone is locked, but it isn't working. I even rebooted...and you can still get Siri to engage! Any ideas??
I'm having the same problem after I moved my iPhoto Library over to an external harddrive (and then tried to access it on separate occasions from different machines). I also found that my iPhoto had "locked" these directories somehow, and I checked the "Get Info" details: sure enough, one of the things that should have said "Read and Write", didn't.
But when I tried to change those permissions (including the "Apply to enclosed items"), it gave me this error:
"The operation cannot be completed because you do not have sufficient privileges for some of the items."
Seems that I can't give more permissions because I don't have enough permissions to do that! Do I have to move the owners to "System" from my own account "b" or what?
(My poor "photos to be iphoto'd" directory is filling up quickly while waiting for iPhoto to be fixed.) Thanks!
Maybe you are looking for
-
Is there a way to get Thunderbird to default open to the calendar tab?
I realize that if Thunderbird is closed in the calendar tab it will open in the same tab next time I just wonder if I am missing some setting that would always default to Thunderbird opening to the calendar tab without my having to close it from that
-
Return to vendor process from backend
Could anyone of you please share the plsql pseudocode or full process code for return to vendor process ? Regards, Kumar Edited by: 857804 on May 10, 2011 6:20 AM
-
Revert to Factory Settings solved connection problems. Any chance for 3.0?
After trying everything else I could think of to resolve my Apple TV connectivity problems, I resorted to a Factory Reset. Presto!, my Apple TV now streams music like it used to, flawlessly. I miss YouTube, the other new features and the interface th
-
Passing files into labview vi by opening the file
I have a labview exe that is installed on XP that can create/save files with an extension not recognized by windows. The files can be opened from within the exe but what I want is to double click(open) the file from explorer/desktop and have it opene
-
When configuring the Photosmart Estation printer C510a to use the WiFi network, I discovered that the Zeen does not allow that the router hides its SSID. Instead the Zeen wants that the SSID is broadcasts by the router to be succesfull connecting to