My I phone is not getting detected on my PC...
My Iphone is not getting detected on my PC, though it is being recognized by Itunes. Also how can i download the pictures from my phone since it is not being detected by my PC. Its an Acer laptop running on windows 7. Can anybody help???
Check and make sure u have itunes on you PC and then double check that your stuff is plugged in
Similar Messages
-
i have an iphone 4 with 4.3.2 version, want to upgrade but my phone is not getting detected on my comp on itunes. i want to upgrade it to the latest version of the software, please help
If your phone isn't being recognized by your computer, you need to follow the steps in this article to resolve that
Also, some basic isolation needs to be done. Does it show up in itunes on any other computers? do you have other cords you can test with to see if it might be the cord? if the phone doesn't show up on any computers, it's likely your phone has a hardware issue
http://support.apple.com/kb/TS1538?viewlocale=en_US is the article to use if you want to concentrate on trying to get a particular computer to recognize your phone -
Earphones not getting detected
Hi,
I'm using nokia 6233. My ear phones are not getting detected. When i checked the enhancement settings the headset and also data cable options are not present.
Can some one please tell me what exactly can be the problem?if this only started occurring recently, which i presume what is happening here, then it may be due to a firmware problem. my advice would be to check if there is a newer firmware version available on NSU for your phone. if there is, upgrade to this, then restore factory settings after having performing the upgrade. if no upgrade available, then try restoring the phone to factory settings to see if this rectifies the problem. if this doesn't, then try using NSU to re-install the firmware version you are currently using.
remember to backup all of your data before performing any of the above. let us know how it goes.
If you found this or someone's comments helpful or like what that person has to say, please give some Kudos to their post! -
i have an iphone 4 with 4.3.2 version, i want to upgrade the software. but my phone is not getting synchronised on itunes and not getting detected. also there is no update software tab under settings.please help me
If your phone isn't being recognized by your computer, you need to follow the steps in this article to resolve that
Also, some basic isolation needs to be done. Does it show up in itunes on any other computers? do you have other cords you can test with to see if it might be the cord? if the phone doesn't show up on any computers, it's likely your phone has a hardware issue
http://support.apple.com/kb/TS1538?viewlocale=en_US is the article to use if you want to concentrate on trying to get a particular computer to recognize your phone -
IPhone 4S does not get detected in Windows 7
iPhone 4S does not get detected in Windows 7
When I connect my iPhone 4S to my computer, iTunes does not detect it. iPhone pops the message of USB connectivity and defaults to Mass Storage. Windows shows the message that "Device is ready to use" and I can read both drives of the iPhone in Windows Explorer. However iTunes does not detect the device and the "Devices" tab does not appear. I have tried Restarting the phone. Restarting the computer. Connecting the phone to a different computer. (I'm on version 4.3.3 (8J2), firmware 01.59.00 and iTunes 10.5.3.3).First make sure you usb drivers are up to date
http://windows.microsoft.com/en-CA/windows-vista/Tips-for-solving-problems-with- USB-devices
Try a hard reset on your iPhone, press the power/sleep & home button at the same time until the apple logo appears (ignore the slide to turn off prompt). Once the apple logo appears release the buttons and wait for your iPhone to boot back up then try connecting. Also try a different USB cable if you have one available. -
i have a friend who was going to sync her phone with my computer to get the new update.. how do i add her phone with out her losing everything on her phone and not getting all my info on her phone..
First, create a separate login on your computer for your friend. Do this BEFORE you do anything else. Next, make sure iTunes is up to date. Then:
1. Disable auto sync when an iPod/iPhone is connected under Preferences>Devices in iTunes.
2. Make sure you have one contact & one event in the supported applications(Address Book, iCal) on your computer. These entries can be fake, doesn't matter, the important point is that these programs not be empty.
3. Connect her phone, iTunes running, do not sync at this point.
4. Store>Authorize this computer.
5. File>Transfer Purchases(To make sure all purchased content on her phone will be in her itunes library).
6. Right click in the device pane & select reset warnings.
7. Right click again and select backup.
8. Right click again & select restore from backup, select the backup you just made. When prompted to create another backup, decline.
9. This MUST be followed by a sync to restore her itunes content, which you select from the various tabs, You'll get a popup regarding her contacts & calendars asking to merge or replace, select merge.
You should be good to go. -
HT1369 iphone4 is not getting detect in my itunes after installing itunes 10.7.0.21
iphone4 is not getting detect in my itunes on Windows vista (OS) after installing/upgrading to itunes 10.7.0.21
Device not detected in iTunes
-
Ipod not getting detected in Windows
I have this iPod shuffle(512 MB) which plays songs perfectly but there is this problem since past few days that its not getting detected at any of the computers. I have downloaded the latest updater n tried installing that also but of no use. I had purchased it from US and now i'm in India.
Please tell me what to do ?
You can contact me on [email protected]the shuffle will only actually work with one itunes library, so what do you mean by "any of the computers". if you haven't already, pick the computer you want to use, ensure that itunes 4.9 and the latest updater s/w is installed, then conect your shuffle, and under explorer reformat the shuffle. then disconnect and re-connect the shuffle, and reload the updater s/w. this will remove all the tunes from your shuffle, but should work ok
-
External HDD not getting detected?
My 250GB Transcend External HDD is not getting detected. Help please. Even yesterday, I had used it successfully. I don't have a clue what happened.
Last edited by armageddon09 (2009-10-14 12:49:39)I have the sam issu with a Coolink USB2.0 external enclosure with a 320GB Hitachi HD.
The relevant informations are:
# uname -a
Linux arch.aneder.hu 2.6.31-ARCH #1 SMP PREEMPT Tue Oct 13 11:33:39 CEST 2009 x86_64 AMD Turion(tm) 64 X2 Mobile Technology TL-60 AuthenticAMD GNU/Linux
# lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 04f2:b028 Chicony Electronics Co., Ltd VGA UVC Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 152d:2329 JMicron Technology Corp. / JMicron USA Technology Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
after ca. 5 second:
# lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 04f2:b028 Chicony Electronics Co., Ltd VGA UVC Webcam
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
# dmesg
usb 2-3: new high speed USB device using ehci_hcd and address 2
usb 2-3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access Hitachi HTS541616J9SA00 PQ: 0 ANSI: 2 CCS
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 34 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: device scan complete
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] Attached SCSI disk
usb 2-3: reset high speed USB device using ehci_hcd and address 2
usb 2-3: device descriptor read/64, error -71
usb 2-3: device descriptor read/64, error -71
usb 2-3: reset high speed USB device using ehci_hcd and address 2
usb 2-3: device descriptor read/64, error -71
usb 2-3: device descriptor read/64, error -71
usb 2-3: reset high speed USB device using ehci_hcd and address 2
usb 2-3: device not accepting address 2, error -71
usb 2-3: reset high speed USB device using ehci_hcd and address 2
usb 2-3: device not accepting address 2, error -71
sd 6:0:0:0: Device offlined - not ready after error recovery
usb 2-3: USB disconnect, address 2
It wasn't any problem with 2.26.29-ARCH kernel.
Any hints?
TIA -
iphone 4s not getting detected in macbook after connecting via usb cable, also photos taken in iPhone not showing in macbook pro
Thanks. I realises that i will hv to go to iphoto to see the photo. Its now working !!!!!
-
I have a standalone isight and I use an IMAC G5.Its funny that my isight is not getting detected by my imac at all!! I have tried changing the firewire ports, but I just dont understand!! I hadnt been using for about a couple of months, I come back and try videochatting and it just doesnt work!!It says isight not connected!!
Can you suggest, what I need to do. I dont think I have the CD for isight either. I have had this isight for about 2 years now!I had the same problem with my macBook. All of a sudden the green lites on my built in camera were not on and it did not recognize my isight camera...Couldn't get it to work till I plugged in an external isight camera....started working for a few weeks....then quite working again and read about reseting the prm on an intel based macbook....shut down everything, disconnected all power THEN pushed the power button for 5 seconds....repowered the computer and is came back on working.
Only problem, and the mac dealer told me this didn't matter but I'm not sure...I only get one green lite instead of two...
any thoughts on this...
Rick -
SQL server instance not getting detected during SCOM 2012 R2 Installation
Hi All,
This is related to the below thread which i created. But i wanted to test this practically in a LAB equipment
https://social.technet.microsoft.com/Forums/en-US/96feece7-c168-4f42-b62e-4c0c20f8d525/does-scom-2012-2012-r2-setup-detect-a-sql-instance-of-a-sql-server-in-the-same-network-which-is-in?forum=operationsmanagerdeployment
So i want to install SCOM in my domain, But i want to use a SQL server in my network which is in another domain.
So i have 4 server machines as below:
SERVER_DC1 - Domain controller of 1st domain.
SERVER_DC2 - Domain controller of 2nd domain.
SERVER_SQL - SQL server 2012 Enterprise installed for SCOM but is in Domain 1
Server_SCOM - I want to install SCOM in this but which is in domain 2
I created a trust relation between 2 domains with a Forest trust 2 way transitive.
I have created a security group and added that as SQL Admin during the installation. Later i added one Domain administrator account from Domain 2 to this security group.
When i do a installation in SERVER_DC1 for testing the SQL instance is being detected as below.
When i do the installation in Server_SCOM which is in another domain then the instance is not getting detected.
I have turned off windows firewall in all the machines.
Before creating the trust i ran the setup in Server_SCOM then it was giving me a warning saying it is not able to access the SQL server due to permission issues.
After giving permissions my instance is not at all getting detected.
Can any one help plz.
Gautam.75801Hi Yan Li,
Really a helpful post. I tested the connection. I connected to the SQL server in Domain A using a server in domain B logged in as a domain B user to whom the SQL permissions are provided. The result says It was successful.
Below is the screenshot.
I don't understand why is it not getting detected in the SCOM setup.
But 1 more important thing which i forgot to mention.
When i log on to the server in which i want to install SCOM in domain B, But by using Domain A's user account (Added as a local user in SCOM server in domain B), Then the Instance is getting detected.
Below is a screenshot of that.
So has any one faced such a type of issue ?
Gautam.75801 -
my phone is not getting started,its displaying itunes sign and USB sign on the phone's screen. I have also restored and updated the phone however not getting started
It helped earlier but it has come back again. I don't know what to do. I tried what you said earlier but this time even this is not working either. And quite intrestingly my phone won't turn off. I turn it off, it goes off and then restarts on its own and then keep giving the same message again and again.
Could it be a charging cable, is there any chance that the cable which was working fine one day could turn to be "incompatible" with iphone the other day????????
Please help -
Iphone does not get detected in windows 7
Hi,
Whenever I connect my iPhone to my lap, it does not gets detected.
It enters into charging mode.
But it gets detected in iTunes.
How to make it detected outside iTunes ?hi..
i also have a same problem..
i am using windows7
and none of my iphone gets detected..!!
i have a iphone5 and 4s
i also tried formatting my pc but em nt getting a solution for this..i tried all of the solutions listed in the thread..
plzz help -
Was skiing with a lifeproof on and my phone did not get wet. On the ride back my phone was struggling to send/receive messages and had trouble opening apps. The screen froze and I hit the sleep button; since then, it has not turned on. Any suggestions on what to do?
It probably got too cold and shut down. Warm it to room temperature, then hold the HOME and SLEEP buttons at the same time until an Apple logo appears.
Maybe you are looking for
-
What happened to the images in the desktop Messages app?
Before Mavericks, images received via the messages app would appear in the Messages application window. In Mavericks, however, the images are replaced by a generic JPEG icon. In order to view the images, you have to click attorney magnifying glass
-
Why am I getting an error message when trying to replace existing music on itunes
How do I stop the error message from showing up when I try to replace existing music on my iTunes?
-
Linking between different websites
Hi How to get a couple of rows of from a search result of different website from ours. For eg.: I am entering a search criteria from http://www.a.com/examples/a.jsp and searching the result from www.b.com/examples/query?q=query Now, the tricky part i
-
Receipt Close Point at Delivery ? When PO Closed ??
HI ALL, I am very new to the Oracle Forums, Me also put mine question into the Oracle Communities (Procurement). Here I just wanted to know one thing from you, Let us consider the case the Receving day Early and Days Late is 0 and Reciiving Close Tol
-
Firefox on Mac, now Bing search has replaced Google and I can't get rid of Bing- how?
Bing has mysteriously replaced Google and pops up in new tabs, etc. I have tried to change this, but Bing pesists. I don't want it, I didn't ask for it (intentionally, anyway) - how do I get rid of it?