My imac g5 from 2004 crashed, and now it won't turn on. Help?
Not much else to say. My i-mac G5 which I bought in 2004 started crashing ocassionally a while back. It would always restart, but then the power button started not working. I would sometimes have to push the button many times to get it to start. Am I f**ked?
Try opening the case and see if the power button contact is properly aligned. Once the case is open, inspect for bulging or leaking capacitors.
You can also run
Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Then reboot and repair perm issions.
Similar Messages
-
I reset all contents and settings on my ipad and it won't turn on, when i try to open it the apple logo appears and then nothing happens
Hi how did you resolve this problem
-
iPod touch 3rd generation crashed while updating, and now it won't turn on, and it won't charge or be recognized in iTunes because it's completely dead; it's been dead for 3 days now. I've tried pressing home/sleep buttons for reset but nothing works, I've tried using different usb ports to charge it, but nothing seems to work. Please help asap. ...Thanks!(:
After charging the iPod for half an hour, see if placing the iPod in recovery mode will allow iTunes to see the iPod so you can restore the iPod. For recovery mode see:
iPhone and iPod touch: Unable to update or restore -
What can I do? I dropped my iphone (not from a great height) and now it won't turn on however when I plug it in the white apple shows on my screen. My lock button has been broken for awhile so I can't even try switch it on!
Once you have a proven, working Charger... Charge the Device for a couple of hours. Then try to turn it on.
If no joy...
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
If the issue persists...
Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
Be sure to make an appointment first... -
My ipod has been accessed from another ipod and now it won't let me download anything what do i do
my ipod account has been accessed from another ipod and now it won't let me download anything...What Do I do?
Not sure what you are talking about.
Your ITUNES account can be accessed from any device or computer that has itunes, as long as you have your username and password. Using your itunes account from another device does not affect your ability to use the account from your device.
What is the issue?
You tried to do what?
And what was the result?
Error message?
What did it say?
What have you tried? -
I tried to download iOS 6 on my iPod 4 and I disconnected my iPod from my computer and now it won't load. I even tried reconnecting my iPod to the computer. Help Please!
I was trying to update my iTunes, so the computer asked me to restart my computer. After I selected shut down. I knew it was a mistake. What should I do?
-
I did the SMC reset for my iMac intel-based and now it won't turn on. What can I do to fix this?
Well, first things first... is the power cord fully plugged into the back of the iMac (and the wall, for that matter)?
Make sure the wall outlet has power, too... I've scratched my head over stupid issues where I forgot to flip a wall switch.
If the outlet does have power, then try doing a pram zap. Command + option + P + R (hold those at startup).
If the machine is receiving power, you should be able to see some LEDs if you look through the bottom grate of the machine to the left of the RAM door. -
just bought a new iphone4 and was loading os6 and now it won't turn on. the apple glows like it is starting up, then the screen goes black and then repeats the same process over and over. i have tried to reboot multiple times now
I am assuming the phone was working prior to you installing IOS 6? Did you use itunes to install IOS 6 or just run from the phone?
When I tried to do the Over The Air update to IOS6 on my iPhone 4, it errored out and I had to connect it to iTunes and select "Restore" from the summary screen after iTunes finds the phone is connected. If this works for you, it will go through a couple of reboots that take a few minutes to complete. It should then give you the option to start with a fresh new phone or to use one of your previous backups to load your contacts and other information, provided you have backed up the phone previously.
I hope this helps you my friend! -
Have updated my iPhone 5c to iOS 8 and restored it and now it won't turn on. I have tried plugging it in even though I know it was fully charged, I have shut down my rebooted my computer and iTunes from scratch and reconnected my phone and still nothing, any ideas?
Hello Nikmuz,
It sounds like your screen is either black so it looks like it is not on, or it is just plain not turning on at all and it is also not being recognized in iTunes. I would recommend the followng troubleshooting from this article to help you determine whether that is the case or not, named:
iPhone: Hardware troubleshooting
Toggle the ringer switch to see if the unit vibrates. If it does, it could be that iPhone is getting power, but is not displaying any image.
While connected to the iPhone charger, try to reset the iPhone.
My issue is still not resolved. What do I do next?
Contact Apple Support.
Thank you for using Apple Support Communities.
All the very best,
Sterling -
I turned my iphone off when visiting the doctor's surgery and now it won't turn back on. It had 73% battery left and I have tried connecting it to my computer with USB but nothing happens. I have taken out and replaced the sim card too. Any suggestions
If wjosten's tip doesn't work try plugging it into a USB charger (not through your computer), wait about 30 seconds and it should come on. If it doesn't remove the cord from the phone and keep trying this. I've had this same issue and found a combination of the reset & charging cable tends to work. Sometimes it takes about 5 minutes for the phone to respond.
Best of luck. -
Dropped iPhone and now it won't turn on??? :(
Dropped my iPhone 3GS and now it won't turn on. I didn't even drop it that far or anything but now for some reason it won't turn on. I've already tried resetting it several times and it hasn't worked. I plugged it in to charge it and nothing happened and when i plug it in the computer with the dock, nothing happens and it won't even show up under devices in iTunes.
Please help.
-SammiI believe the correct technical term is... "you broke it".
Take it in for service. An out of warranty replacement from Apple is US$149. -
I was syncing my phone to itunes and then my phone automatically locked and now it won't turn back on but when i plug it into a charger it makes the charging sound.
Hi lemmag17,
If your iPhone doesn't appear to be responding or turning on, you may find the following article helpful:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Regards,
- Brenden -
I haven't used my iPod touch 4g in a while and now it won't turn on or connect to my computer to charge. holding power+home isn't working either. i've had it plugged in for a while, but i'm pretty sure that's pointless if it won't even connect....help?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
I cracked my iphone 4s screen and now it won't turn on
So I dropped my iphone 4s and cracked it and then I picked it up and now it won't turn on. I've tried plugging it into my wall, computer, etc. I don't know what to do, so what should I do? also will i be able to access my photos again because my photos aren't backed up or anything? also i would like to access my notes again? I'm so confused and don'please help!
Sounds to me like your phone is broken as well. Without a backup you've likely lost your data. You could try taking it into an Apple store or contact them and see if they have any way recovering your data. Likely not but worth a try.
-
my iphone 4 turned off and now it won't turn back on I've tried charging it and plugging it into my computer but it's still a blank screen. please help me.
Intel-based Macs: Resetting the System Management Controller (SMC)
Maybe you are looking for
-
hello, I recently had to set up my network. Now My ipad and iphone no longer see the time machine. I have all green on the time machine and two airport express, my internet connection is a modern 2wire. Before the latest set up I could see the time m
-
Example Basicresponse: HTTP Error 403 - Forbidden
Hi, i installed the developer edition of ocms. The eclipse plugin works fine. I was able to deploy the "thirdpartycallcontrol" and to access it via http://localhost:8888/tpcc. BUT the basicresponse example does not work. I can deploy it but on http:/
-
Convert standard video files in to flv file at run time
Hello All How can we convert standard video files in to flv file at run time like you tube and Google Video is there any script or tool to do this. This is urgent. I have one project in this project client requiring function like whatever standard vi
-
Correspondence types (transaction FB12): How to print a document?
Hi, I am using transaction FB12 to test correspondence type "account statement" in quality. When I enter the correspondence type, customer number posting dates, it get the message that the account statement was requested. When I go to the spool (SP0
-
How to do configuration in Integration Builder for Idoc to PI to EDI system?
Hi Experts. I am working on one interface which is SAP IDOC (DESADV.DELVRY03) >> to>> PI >> to>> EDI system. I am done with all ESR objects, Can anyone help me about how to and what configuration required to be done in Integration Builder? And after