My import wizard won't work

My import wizard won't work, when it goes to the selection, I select to import from internet explorer, hit next and it just sits there and does nothing.

Let's start with your wireless router. I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

Similar Messages

Report and Layout Import Wizard does not work

We used the Report and Layout Import Wizard extensively in 8.80 with no problems encountered.
We are now upgraded to 8.81 PL07. This is the first attempt at using the wizard in 8.81. The intro window of the wizard, with 'To Start, use the "Next" button' message is as far as I can get. The "Next" and "Cancel" buttons are inoperative - when I click them, there is no response (but they are not greyed out). The program has not crashed - I can move the window, and the "X" close button at top right works, but nothing else does. I am logged in as a superuser, running B1 in an RDP session on the server, same as under 8.80.
Any ideas out there?

Hi,
This is a 8.81 PL07 bug!
I had the same problem this week, and i found the note [1615932 - Buttons "Cancel" and "Next" are inactive in Report and layout import wizard window], that says that it is corrected on PL08!
Regards,
Alice

An important app won't work , just shows a black screen

Ok so I've got this app called "speedbit" , which happened to be important to me @_@
anyway , it won't work , whenever I open it , it just shows the program's Logo and then directly shows a black screen
please ,
1- I did restroe my Ipod touch (3g)
2- I did reset it -.-
3- I did delete the app and re-installed it
4- I did update my Ipod (5.0)
and thanks , I'll really appreciate it if you know how to slove this case
SERIOUSLY
thanks .

Same thing here, screensaver started doing this since I upgraded to Mountain Lion.
Model Name:          MacBook Pro
Model Identifier:          MacBookPro6,2
Processor Name:          Intel Core i7
Processor Speed:          2.66 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache (per Core):          256 KB
L3 Cache:          4 MB
Memory:          8 GB
Processor Interconnect Speed:          4.8 GT/s
Boot ROM Version:          MBP61.0057.B0F
SMC Version (system):          1.58f16
OS X 10.8

Dll import wizard won't go past "Configure include paths"

In the LabVIEW 8.5 version of the "Shared Library Import Wizard" I'm unable to proceed past the "Configure include paths" screen. I get a dialog that reads "Parsing header file" butI am returned to the"Configure Include Paths" screen.
The library imported without error in LabVIEW 8.2.1.
There is no "Report Generation Toolkit" installed.

I can confirm that I am able to use the "Call Library Function"
nodes and that there are no errors indicated when running the wizard. I
get up to the "configure_paths" screen and when I click Next I am shown
the "parse_dialog" screen momentarily but am returned to the
"configure_paths" screen after about 3 seconds.
I have
tried an install on another machine with identical results. The .dll I
am importing was created in MS Visual Studio Express 2008 and imports
well under LabVIEW 8.2.1's import wizard.
Attachments:
configure_paths.JPG ‏37 KB
parse_dialog.JPG ‏8 KB

The "Import Bookmarks" won't work if there's no backup dates... What to do?

I just swapped-out my desktop PC's, and I have lost ALL of my Firefox Bookmarks :( I have been thru all of the "Import and restore" help guides, but unfortunately any earlier restore dates are just not offered to me... only the 1 date after I did the computer swap. How can I get my old bookmarks back and onto my new PC? I'm using Windows 8.1 Thanks!

Do you still have your old computer running, or do you have the hard drive from your old PC, or do you have a copy of the hard drive, or did you use a data transfer tool to copy old data onto your new computer?

Importing CDs won't work

I imported a bunch of songs a couple of days ago and now when I put in a CD to import additional songs the window doesn't pop up with the list of songs to import. I cannot figure out what's going on and it's driving me crazy!!!

OK I've tried just about everything. I've downloaded and installed a crap load of software from SONY, tried finding Audio software from the manufacturers, however it gave it to me in a zipped file, which opened was nothing but a mess, so I couldn't figure out how to update that. Other than that, What is an ATA or IDE Bus driver? And how can you tell if they’re on the same IDE? Is it the Bus Address above? (0,0)
I’ve updated the CD/DVD Mashita Drive firmware, Phoenix BIO, the DVgate, the nVIDIA GeForce Go 6200 Graphics controller Driver, and the VAIO Media Software as well. Windows is set to update automatically daily (or whenever new updates are available). and I've even messed around with the registry system, which I'm freaked out about because I dont want my DADS computer screwed up permanently so I made back up copies and emailed myself directions.....I'm going mad, can u tell? SOOOOOOOO, I've tried it over and over and over, and have constantly referred back to the articles and forums, and still can not figure out what the heck I'm doing wrong!!! Here is a copy of my diagnostics, and some drivers do not yet have updates to them, and others dont have the name of manufacturer but just says (standard system devices). So here r my iTunes 7 (PITA!!!!) Diagnostics: please review and tell me what i'm doing wrong please!! Just the first audio CD is being read, anything after that, WILL NOT BE ACKNOWLEDGED in iTunes under devices!!! I dont under stand it...
CD Diagnostics:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Sony Corporation VGN-S460
iTunes 7.0.1.8
CD Driver 2.0.6.0
CD Driver DLL 2.0.6.0
UpperFilters: GEARAspiWDM (2.0.6.0),
Video Driver: NVIDIA GeForce Go 6200 \GeForce Go 6200
FlashMedia\MSorMSProDevice, Bus Type SSA
IDE\DiskFUJITSUMHT2080BH______________________40000049, Bus Type ATA, Bus Address [0,0]
IDE\CdRomMATSHITAUJ-832D________________________1.03___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is an administrator.
E: MATSHITA UJ-832D, Rev 1.03
Drive is empty.
Writing CD text is turned on in the preferences. If you're having problems burning CDs, try turning this preference off.
Would Appreciate input soon!

User Registration Wizard won't work

I have tried to use the User Registration Wizard numerous times. Each time it freezes Dreamweaver CS3. I have to uninstall ADDT and reinstall it in order to use ADDT again.
Anyone else having this issue? It's not giving me any errors at all. Just freezing everything up.
Thanks.

so the table name is "user" then ? If so, this name is known to cause such errors, because DW internally treats this one as reserved word
Cheers,
Günter Schenk
Adobe Community Expert, Dreamweaver

Import using develop presets won't work!

Hi all,
I just upgraded from LR2 to LR3. A lot to hate in this new version. But I suppose one needs to adjust and no doubt I will, but there is one thing that is about to drive me up the wall. Something I haven't been able to fix, so here I am, looking for a bit of help.
Here's the problem:
Because I don't like Lightroom's Sharpening & Noise Reduction settings, I used a preset in LR2 that I applied automatically when importing my images into LR. Now, with Lightroom 3 this just won't work properly and I get exclamation marks, indicating those images are not in the 2010 develop environment. I realised I was using my old presets, created in LR2, so that made sense. So I first deleted all my old presets and to make sure, I also deleted my metadata preset that I also apply on import. I couldn't find a way to delete those presets from within Lightroom by the way. So I just went to the library and trashed them manually...
Next:
I open LR3. Now I have no user presets anymore, of any kind. I then import the first image of today's shoot. In the develop module I make sure that I'm working in the 2010 process environment. I set Sharpening and Noise Reduction to what I want them to be and make them a preset. Then I made another preset for my metadata. But after importing the rest of today's shoot with the presets I have just created, it will not accept the 2010 settings and I get the exclamation mark with every image. I have checked that the culprit is not the metadata file. If I use only that to import an image and leave the Develop Settings on None, all is well, and the image is regarded as being in the 2010 process state. If I then *manually* apply my earlier created Noise Reduction/Sharpening preset, it accepts it and all is well. But as soon as I try to apply that same preset again when importing my images, then, when I go to the develop module, the image is suddenly in the 2003 environment again and I get the exclamation marks. I have tried everything I can think of but I cannot escape it any longer: I have been defeated by Lightroom 3. What on earth am I doing wrong here? Anybody?

Yes, I get the same thing with the sliders being greyed out. Funny thing is that the sliders *are* set exactly as in my preset and when I click 'yes update' to 2010 standards, the settings don't change but only the sliders become accessible. The thing is that I really don't want to be doing that with every import, even if you can do the whole batch at once. What I don't understand is that when I import with the preset turned off and apply it in Lightroom's Develop Module, it accepts it without a problem but that when I use the same preset on import, it won't work properly.
Now what the poster in the other thread said was:
"When I saved a new preset and selected to also save the process version, a line in the preset was created: ProcessVersion = "5.7". When I cut and paste that into all my other presets then the sliders were all active when I used them."
I have no idea what he is talking about or how one would do that. When I create a preset I simply click the + sign and in the pop up window select what I want, give it a name and that's it.
Edit: Sorry, I apparently overlooked the Process Version box in the preset panel! Must have been a case of not seeing the forest for the trees. Problem solved. Thanks.

Importing cr2 raw files won't work on ios 6 when it worked fine on ios5. Anyone have a solution?

I have been importing cr2 raw files to my iPad using ios 5 but importing cr2 raw files won't work on ios 6. Sees files in camera but when import stops it fails with an exclamation mark in red circle. Anyone have a solution?

Don't know if you care anymore or it applies, but I was able to get things working but it took drastic measures.
I had to do a full system reset and update by doing the following:
- Make note of all your settings in your system and apps especially accounts and forget about in app data that's only on your iPad and not in a cloud service because it will be gone after this
- Connect iPad to Mac and startup iTunes
- Hold down Home and Power buttons simultaneously for about 8 sec until the screen turns black
- Release the Power button but continue holding the Home button until there's a popup on your screen which indicates it's in recovery mode
- Follow the instructions to recover your iPad but recover it to factory state, not recover from a backup
- Reinstall all your apps and content
- Reconnect to all your services on your system and apps
I could not restore from a backup since it brought back my bad data too. It also didn't restore my music and no matter what I tried it wouldn't put my music onto my iPad. Had to start clean.
It appears over time that the system gets dirty and there's lots of bad data that can't get resolved. This is especially true if some of your apps have crashed a bunch.

Import Excel with Import Wizard / Problem during the import of "Actual Work" column

Hello,
I am trying to import an Excel File (*.xlsx) to Project Server 2013 through Project Professional 2013 and Import Wizard.
I am having trouble when I try to include the column "Actual Work". After selecting the columnsmapping I am getting a strange error message saying that "The File cannot be oppened","Make sure, that the Filename and Path is right"
and some other strange messages concerning compatibility, although I am using the same File, which works perfectly without the "Actual Work" column.
I have tried as well with csv and the outcome was the same.
Any help is welcome!
Thank you in advance,
Ioannis

Which DW are you using - DMX on Mac? It didn't have that
option. This is
not an Educational version issue - it's a Mac issue.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"Terry_Straehley" <[email protected]> wrote
in message
news:fm85u9$5ec$[email protected]..
> From a 11/06 post
> <<Hi, My Dreamweaver MX Education Version does NOT
have the Import to
> Excel
> option. I am using "Excel 2003 (11.6560.6568) SP2, Part
of Microsoft
> Office
> Professional Edition 2003". If I start with a blank page
in Dreamweaver,
> click
> on File, Import, I only have the options "XML into
Template", "Word HTML,
> and
> "Tabular Data". Does anyone know why I don't have the
"Import Excel" >>
>
> This was not answered in the thread I copied it from. I
have the same
> problem.
> Can some one answer the question?
>

Continuous raster is not working for imported Illustrator files - I am working on the latest versions of both. I tried importing a simple graphic and having it continuously raster, nothing else, and it won't work.

I set up my file in Illustrator as a video file, same size as the AfterEffects file I'm working on - but the continuous raster button doesn't work. Any ideas?

If you have applied raster layer effects in illustrator, then it won't work because you no longer have a vector image.
What is the zoom factor of your composition window? What is the resolution of your comp window? If you would post a screenshot of your composition with the properties of the layers in question revealed by pressing the u key twice maybe we would have a clue what you are doing wrong. It's quite difficult to come up with an answer with out some details. We need more details.

Import function in Premier 6 won't work; crashes 90 percent of the program. How to fix?

I was working on a project in Premiere Pro 6. I had imported about 200 files and almost completed the project. I tried to import another file and the import function would not work. In addition, it disabled about 90 percent of the program. Menu selections had turned grey. I closed the project and program and restarted, opening a much smaller project. Worked OK until I tried to import. The import wouldn't work, and the program was disabled. This is not a case of actually selecting a file to import. The function crashes before you have a chance to actually select a file. On deadline, please help.

These may help
Reset Corrupted Preferences = Press/HOLD Ctrl+Alt+Shift while starting program
-and setting http://forums.adobe.com/thread/1058426?tstart=0

HP LaserJet Pro C1415fn color MFP - fax won't work

I have a LaserJet Pro CM1415fn color MFP on a Windows 7 64-bit laptop. I've been using the printer for two years now.
At the moment the fax function only works if I use it manually (i.e. if I place a sheet of paper on the scanner, select the "Fax" button on the printer touch pad and dial the number). However, if I want to send a fax via the PC interface, it won't work.
For example, if I open a PDF, click on "Print" and select "HP LaserJet Professional CM 1410 Series Fax", nothing happens -- no window/interface will open. If I select "HP Send Fax" or "HP Fax Setup Wizard" from the program menu, nothing happens.
I've always been sending faxes this way and I just don't know what happened... Can anyone please help?
Thanks in advance!
Claudia

Hi @Clabee ,
I see that you can't fax from the PC anymore. I can help you with this.
If this just recently happened, I would do a System Restore back to when everything was working properly.
System Restore for Windows 7.
If you would prefer not to do the System Restore, uninstall and reinstall the printer software. It might become corrupted.
Here are the steps to run the uninstall from the computer or the CD.
To uninstall from program files:
Touch the Windows key and the E key to access the computer window.
Select the C drive.
Select program files or program files x86.
Open the HP and printer name folder.
Select uninstall.
Uninstall the software from the CD:
Touch the Windows key and the E key to access the computer window. Right click on the CD for the printer, left click open in a new window, double click on uninstall.
Disable all the start up programs and temporarily turn off the Antivirus Software. How to use MSCONFIG .
Click on the start up tab and click disable all.
Download, save and install the latest drivers.
HP LaserJet Pro CM1415fnw Color Multifunction Printer Drivers.
Test the printer and try sending a fax again from the PC.
Then you will need to go back in and enable the start up programs and turn the Antivirus Software back on again.
If you need further assistance, just let me know.
Have a wonderful day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Flash is up-to-date, but Plugin won't work

Hi!
I'm using Firefox 29.0.1 on Windows 8, (also up-to-date), and Flash plug-in won't work. I re-downloaded & installed Adobe Flash 13.0.0.214...I verified it on their website, but I can't get the plugin to work. I had no problem with it earlier today, but for some reason it won't work anymore.
PLEASE HELP!
Thank you,
Nuts4Mutts :(

Hi!
Yes, I checked on Adobe's site THREE TIMES & I have the latest version, & the animations they have on their site worked fine...I saw them perfectly, (both the red cube bouncing around & the cartoon tree with the animated yellow & orange colored leaves). I'm at a loss why on most sites I have no problem watching streaming video, but on 2 of the other sites that I watch EVERY day, I suddenly get the "Error loading plugin" message on a black screen. It's driving me nuts, as I was watching these sites earlier this morning & everything was fine. The confusing part, to me at least, is why is this plug-in problem is ONLY affecting 2 of the sites I watch AND why did it happen out of the blue...I was watching them without any problem early this morning, just like I do ALL DAY...EVERY DAY!!! (I watch several wildlife live-cams, so it's important that I keep up with changes in the birds I normally watch). None of the other sites I watch are affected...what would cause this to happen?
I even did a complete shut-down of my laptop, waited, then re-started. Usually, this would fix just about anything...for some reason, I can't get the video stream on 2 cams...I can still view the other cams I watch, though.
I DID install MS's weekly updates, but it didn't affect my ability to see streaming video on most of the sites I watch; so far only on 2 of them.
I only have the pop-up blocker that comes with Firefox, but other than that there's nothing else in my add-ons that could interfere. I checked my plugins several times, just to make sure Flash was up-to-date & they're fine, too. The mystery is why I can see my wildlife cams on 4 of the sites I watch but not on the other 2, especially when I was watching them early this morning!!! I feel like I've been dropped-off in some sort of cyber-space time warp, or in the twilight zone & I'm ready to scream!
If there are any other suggestions, please post them...I'm very behind in my cam-watching!
On another Firefox-related problem...where do I post a question about some add-ons not working or being visible AND not being able to customize since the last update? I know...I'm just having a very confusing, frustrating day!
Thanks again for your ideas...I need all the help I can get!
Nuts4Mutts :(

TS1538 Hi, I have the problem which iTunes cannot detect my iPhone 4s. I tried the steps you have provided in your troubleshooting, but it won't work for me because the Apple Mobile Devilce is perfectly installed on my windows.

Hi, I have the problem which iTunes cannot detect my iPhone 4s. I tried the steps you have provided in your troubleshooting, but it won't work for me because the Apple Mobile Devilce is perfectly installed on my windows. However, the driver "Microsoft teredo Tunneling adapter" has a yellow exclamation mark, which i believe means it's not installed correctly or something is wrong with it. This driver is under the Network Adapters (Please see picture below).
This is what happens when I connect my iPhone 4s to my laptop (Windows 7 Starter 32-bit)
1. The phone charges it's battery
2. I can open it in My Computer and import/export media files.
In iTunes
3. It start to sync until step 3 then stops.
4. The iPhone option with an arrow appears beside the iTunes Store, but when the arrow is clicked it disappears.
I hope you can provide me a solution for this problem.
Thanks,
Ralph

Hi ralphagir,
Welcome to the Apple Support Communities!
For your iTunes issue with it not recognizing your iPhone, I would go ahead and suggest deleting iTunes and all of its components from your Windows computer and installing fresh.
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/HT1923
Remove iTunes and related components from the Control Panel
Use the Control Panel to uninstall iTunes and related software components in the following order and then restart your computer:
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
Important: Uninstalling these components in a different order, or only uninstalling some of these components may have unintended affects.
As far as the arrow button that you click and the iPhone disappears, it sounds like you may be clicking on the eject button. Please take a look at the following article for information on the eject button in iTunes.
Safely disconnect iPod
http://support.apple.com/kb/HT1853
Have a great day,
Joe

My import wizard won't work

Similar Messages

Maybe you are looking for