My internal microphone is not registering any input

I've tried adjusting the volume of the internal microphone in System Preferences>Sound but it still does not register as receiving any input. How do I fix this?

You've probably done all this but are these settings right? When I speak or snap my fingers I see input on the readout.

Similar Messages

Internal microphone still not working - Pavilion Notebook dm4

My internal microphone is not working. ( IDT high definition CODEC)
I think I have tried everything!
Driver updated
Device is shown as working ( green bars moving etc)
I have uninstalled and re-installed driver
In the past it OCCASIONALLY worked
Now it is not working at all.
Can ayone suggest anything else?
Christopher

Reset PRAM. http://support.apple.com/kb/PH4405
If this does not help, take the computer to the Apple Store to have it checked out.
A new Mac is in warranty for 1 year from the date of purchase.
If there is any manufacturing defect found, it will be repaired free of charge.
Best.

Recently installed Windows 7 on Pavilion dv6748us - internal microphone does not work

Hi,
sojo972 wrote:
I have been searching the web extensively, without success, to find how to resolve this issue.
I recently installed Windows 7, 32 bit, on my wife's HP Pavilion dv6748us laptop. Now her internal microphone does not work.
Have gotten some "roadside" advice to use a Windows Vista driver; Have no idea what the driver is or how to get it.
Have found some information about uninstalling realtek audio driver and reinstalling an older version; Have no idea on this one either.
Would really appreciate a definitive answer with a positive result.
Thanks for all help.
The drivers for the laptop are located here. select Vista and Driver-audio. The Vista driver should work. You can uninstall the driver from within the Device manager. Start --> type devmgmt.msc and the device manager will open. Locate the HD audio device and right-click it and update the driver.
After that is done go to Control Panel and Sound and the recording tab up top. Check to see if the microphone is grayed out. (not grayed out means driver is properly installed). The microphone should also have a green checkmark next to it. It is now a matter of selecting the microphone then selecting Properties to enable the microphone and then test and adjust the input level. Look at the tabs (listen,levels and advanced).
Had you considered trying Windows update or the Realtec website as a drivers source?
regards,
erico
regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Hi:
Looking at your system information you could have one of two possible audio cards:
Conexant HD audio or the RealTek HD Audio
The fact that you couldn't install the RealTek HD audio driver indicates to me that you don't have a RealTek audio card. Check your device manager and look at your sound card and check to make sure which audio card you have.
Here is the Vista 32 bit driver for the Conexant audio card:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
Here is the Vista 32 bit driver for the Realtek audio card:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
If you in fact have the Realtek audio card, I would download and install the latest, greatest HD driver directly from the RealTek site:
Accept the agreement, download and install the first one on the list. Maybe it has been updated to fix the issue you are experiencing.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownT...
Paul

In iCal - I keep getting the error message " This calendar was created by Mail" and it will not accept any input; why..??

In iCal - I keep getting the error message “ This calendar was created by Mail” and it will not accept any input; why..??

use Disk Utility and Verify Permisions then fix and Verify Disk and fix, this should fix it.

Re: Satellite Pro L500-1PU - internal microphone does not work

I have an L500 -1PU Toshiba, running on 32 bit Windows 7,
The webcam is working wonderfully but the internal microphone is not working properly.
I had an external microphone so i hadn't noticed this problem when i got on skype, but i've recently discovered that when using the webcam the person on the other end can hear faint noises from my computer when i'm playing music or watching a video clip.
How can i solve this and get my microphone working properly such that i can control the volume and actually get full service from my otherwise decent notebook?
Thanks

Hi
Possibly this Toshiba FAQ could help you:
+Whistling sound on the Satellite L500+
http://aps2.toshiba-tro.de/kb0/TSB0402UB0001R01.htm
Its a matter of the settings.
This issue occurs if the microphone volume in the speakers properties is enabled.
After disabling this point the issue with acoustic feedback does not appear anymore.
Hope this helps!

Workbook does not contain any input-ready variables

Hello Experts,
We have one workbook which is not reacting when click on REFRESH or SHOW VARIABLE.
If clicked on VARIABLE screen it is throwing error "The workbook does not contain any input-ready variables" (screenshot attached)
Points I have checked are as below
1. If I create a new workbook by executing the respective query and refresh then it is working.
2. The file is in xls format and I have checked the USE XLS format under Global setting.
3. My Excel version is 2010. SAP version is SAPKW70105. BEx 7.X, support package 8.
4. It is not authorization issue otherwise the issue would have happened for the new workbook I created for testing.
5. Also I tested with user ID with SAP ALL access.
is there any way to repair the workbook so that it respond to Variable and refresh options ?
Thanks,
Gopi R

Work book might be corrupted : As other said need to create / Recover Old work book
Refer Below Doc process For recovering a corrupted workbook :
How to recover a corrupt workbook.

Using a dll function that does not have any inputs from a VI

Hello all, I'm very new to Labview, I have wraped a dll library using the LVlib wizard and now I am trying to use it in a project. I have a function that does not take any inputs or return any thing except that a struct is populated with some status information as part of the call. I am able to draw a StartInterface VI because my void startInterface(const char* configFile, struct status_struct* status) takes the location of a configutation file as an input. But I can not figure out how to connect my Call Library Node to my a function vi that does not have any inputs ( void shutdownInterface(struct status_struct* status)).
Note that the status struct is deffined to be only and out put at the creation of the LVLIB.
Thanks, Mike

Thanks for the responses guys:
I think I am aware of the conotations of inputs and outputs when I created the lvlib I specified the argument struct status_struct* status as only an output instead of the default of input and output.
I do not think that I am doing anything as complex as function callbacks. My immediate goal is to have an executable (I have application builder) with two buttons and two three text fields one text field for the input of the config file, two text-fields for a cstring that is contained in the status struct; one button to start the interface and one button to stop the interface.
This is in all likely hood a case of my self being too dense and missing something fundimental ;-) I just can't figure out how to wire the shut down method after I've configured the call library node. See the attached pictures:
Attachments:
Start.jpg ‏7 KB
shurtdown.png ‏9 KB

WSDL for WSDL based Proxy that does not have any input

Hi all,
I am trying to create a service which is based on a db adapter. The db adapter is created using a procecure that does not accept any input and gives out a cursor. I have created a
proxy based on a wsdl which was created by me. I have not given any soap:body in the input as I dont have any input for this service. When I test the service it is not going into the
request pipeline instead what ever the input (Here input in the sense even the proxy does not have any input as per the wsdl we need to give some xml tag to test it right?)
to the proxy service is getting echoed back. It is neither going inside the request pipline nor Invoking the business service. When I create a proxy service as a plain xml then It is
working fine. I am very confused and donno what to do.. Kindly help me on this.
thanks
Edited by: 887737 on Apr 5, 2012 4:20 AM
Edited by: 887737 on Apr 5, 2012 4:21 AM

it depends on the selection algorithm you have on the proxyservce
on the fourth tab you can dispatch based on soapaction/body/header/etc
you could dispatch on the soapaction and skip the body

I have a pavilion dv4 and my internal microphone is not working. how do i fix this. thanks

I have a pavilion dv4 and the internal microphone is not working. I believe I had it working for 1 time but can;t figure it out. please help. thanks

Hi,
Please check it using these steps:
1. Right click the iocon speaker (bootom right hand side)
2. Select "Recording Devices"
3. Enable the microphone
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Still: Login screen not accepting any input

My login screen not accepting any input.
It appears the screen is not the front most one.
I have to move the main screen to see it and it
never becomes selected to allow input.
I trashed two plist files:
com.apple.storeagent.plist
com.apple.appstore.plist
Ran the combo updater.
The login screen still will not accept any input.
Thanks ... Ken

Hi Stephen et.al.
If you have an account with Twitter, Follow, then post a tweet to @haxiesbeta (Unsanity's Twitter page) or email them at [email protected] The more user input they get about this issue, the faster we see a fix. As with others, adding FM to exclude list in Application Enhancer does not remedy the problem.
One problem I encountered: when I attempted to disable FM via System Preferences>Application Enhancer, a prompt informed me I did not have sufficient access privileges" to enable or disable FM - same for Labels and Window Shade. Hence, I had to manually move FM to the disabled folder via the Finder, then, log-out/in to get the App Store log-in to cooperate. Anyone else encounter this problem?

I have successfully exported subtitles (XML files) from FC version 7 to FC version 6, by choosing Apple XML Interchange Format Version 4. Now the exported subtitles suddenly read in one long line, at the top, not registering any "Enter" keystrokes.

I have successfully exported subtitles (XML files) from FC version 7 to FC version 6, by choosing Apple XML Interchange Format Version 4. Now the exported subtitles suddenly read in one long line, at the top, not registering any "Enter" keystrokes. The same happens even if I re-import the XML file into Final Cut Version 7 (from where I exported the subtitles). Any tips on how to fix this?

You might see if you can bring the xml file into Title Exchange Pro
http://www.spherico.com/filmtools/TitleExchange/
It's a great program and the author was very responsive when I had a problem.
If it reads correctly, you can probably save it back out.
If you want to send it to me, I'll see if it opens.
[email protected]

The internal microphone is not working

the internal microphone is not working

Hello, iytask4me.
Thank you for visiting Apple Support Communities.
I understand that your microphone is not working. Try resetting the System Management Controller (SMC). Once this is done, test using the microphone.
Intel-based Macs: Resetting the System Management Controller (SMC)
Cheers,
Jason H.

What can I do about a 2008 iMac that does not accept any input, thus blocking entry of password at startup?

My 2008 iMac (20 inch) often freezes. Now it will not accept any input on startup. I type in my password, but it will not accept any characters I enter. The blinking line just continues to blink. It will not acknowledge my keyboard, mouse or trackpad. I have done a forced reboot and a force reboot combined with subsequently disconnecting the power cord and then restarting. No response from either step. What can I do?
Thanks.

Glad it is working for you.
Have a look at these two articles they may help if it occurs again.
http://support.apple.com/kb/ht3964
http://support.apple.com/kb/HT1379

After upgrading to FF4 for Mac OSX.5.8 the Flash-based website builder WIX will not register any keyboard inputs; eg i cannot type in a title or use command+z to undo something, Why is this?

I am using a MacBook Pro with OSX.5.8 installed. I just upgraded to FF4. I have been previously using the online website builder WIX and now when i open up my website to edit it in a separate browser window it does not register my keystrokes. I can edit with the mouse and make changes but i cant type in any titles or names for save files or anything. Shortcut keystorkes like command+z also do not work.

My daughter has had her Razr for about 9 months now. About two weeks ago she picked up her phone in the morning on her way to school when she noticed two cracks, both starting at the camera lens. One goes completely to the bottom and the other goes sharply to the side. She has never dropped it and me and my husband went over it with a fine tooth comb. We looked under a magnifying glass and could no find any reason for the glass to crack. Not one ding, scratch or bang. Our daughter really takes good care of her stuff, but we still wanted to make sure before we sent it in for repairs. Well we did and we got a reply from Motorola with a picture of the cracks saying this was customer abuse and that it is not covered under warranty. Even though they did not find any physical damage to back it up. Well I e-mailed them back and told them I did a little research and found pages of people having the same problems. Well I did not hear from them until I received a notice from Fed Ex that they were sending the phone back. NOT FIXED!!! I went to look up why and guess what there is no case open any more for the phone. It has been wiped clean. I put in the RMA # it comes back not found, I put in the ID #, the SN# and all comes back not found. Yet a day earlier all the info was there. I know there is a lot more people like me and all of you, but they just don't want to be bothered so they pay to have it fix, just to have it do it again. Unless they have found the problem and only fixing it on a customer pay only set up. I am furious and will not be recommending this phone to anyone. And to think I was considering this phone for my next up grade! NOT!!!!

Why am I not getting any input signal into logic X or GarageBand from my audio interface?

Hello all,
I'm completely new to all this so I will try my best here to give all the details needed.
So, I am using a Mac mini (2013 model: i7 overclocked at 2.6, 16 gbram) and a focusrite saffire pro 24DSP. Overall both are in perfect working order.
My problem, however, is that I am seemingly unable to get any form of signal from my saffire into either Logic X or GarageBand. I am trying to record guitar lined in and I have set all the settings in logic to what I think is right (software monitoring checked, output channels selected, saffire selected for both input and output) and I have set up my saffire mix control - I spent days reading the manual and watching online tutorials.
The saffire mix control is set up thus:
Input 1 - instrument
Daw 1+2 = GarageBand
Daw 3+4 = Logic X
Sample rate 41Khz
Master Output = stereo monitor mix (line outs 1 &2 to my monitor speakers)
Output 3+4 headphones
Is there anything missing here?
As far as this all goes, when I plug in my guitar I can get a very clear "raw" signal from the saffire mix control, but when I then go to set up a track in either DAW and assign the necessary line ins and outs, no matter what I do I cannot get an input signal, not even a partial one (I have the monitoring and record armed options checked btw). I am close to giving tearing my hair out.
I'm sure I am just missing something out?
Thanks in advance :-)

I've plugged into the interface a mic and an electric guitar.
I'm not sure what I did but the guitar is coming through (though it shows no signal on the interface). Mic input level on line, mic registers a tiny bit of sound when I hit the mic (on only one channel) but doesn't register any vocals when mic input is turned up to the max.
Odd thing: stereo/mono button reversed that is when the button is pushed in it equals stereo on the head phones when it says it should be mono and when the button is left unpushed it equals mono when it says it should be stereo.
Monitor is on and volume is at max.
GB system preferences don't list Input 1 or/and 2. Where do I find them?
I've tried everything I can think of. It feels as if I just need to find the right switch but I don't know where to look...

My internal microphone is not registering any input

Similar Messages

Maybe you are looking for