My Ipad 1 is not working. when i put it for charging it shows blinking apple logo

I have Ipad-1 with OS 4.2.
As my i pad sutdown even when it was showing remaining battary as 45%. When I tried to restart it was not getting restrated. I put it on charging and tried to reboot by pressing on-off switch at top and home button. Now I pad is not getting started, it is just showing blinking Apple logo. When I tried to hold home button it was showing to connect to i-tunes.
Now I connected my ipad with computer and it is not showing blinking apple logo of conection option with i-tune. but when i connect it to power socket it shows same blinking apple logo.
I went to apple service centre in Navi Mumbai (India) and they suggested me to replace the i pad at a cost of INR 18000 (equal to USD 375).
Please help if I can restart my Ipad without replacement.

- See if placing the iPad in recovery mode will allow iTunes to see the iPod so you can restore the iPod via iTunes. For recovery mode see:
iPad: Unable to update or restore
- Next, try DFU mode:
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Last, your iPad needs replacement

Similar Messages

What can I do for the following situation: I think my insert slot for the headphones does not work; when I put in any cable that should and can go in all I hear is low frequent static sounds.

What can I do for the following situation: I think my insert slot for the headphones does not work; when I put in any cable that should and can go in all I hear is low frequent static sounds.

You might try talking to the Apple store manager and see if you don't get more help...you might also contact Apple.com/support and see if they can give you a contact with the Apple Italy offices.
Sounds like you have two levels of failure, the first shop that did the repair and broke a wire, and the second that has disabled something else and isn't helping.
Apple officially refurbished equipment is usually good quality. Surprising this has happened but you need to press on with complaints and try for resolution.

I have update my 3g software to 4.21 but its not working when it come to restoring firmware its show a error please help me out

i have update my 3g software to 4.21 but its not working when it come to restoring firmware its show a error please help me out

That error shows up when a phone is jailbroken or you are trying to downgrade the iOS version. Neither of which is supported by apple.

My iphone is not working when i plug off from charger.

My iphone is not working when i plug off from charger. Evenmore when it is on the charger and it still not working, it asks to connect to i-tunes but i can't and i can see only emergency calls. What should i do?

If it only works when connected to a charger, that would indicate a battery issue.
As for the other issue... do as it suggests and connect to iTunes then restore. There is no logical, intelligent expectation that anything on the device can be accessed as long as the "Connect to iTunes" screen is displaying.

My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

Yes if your model MBP has a removable battery. If it does not:
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
http://support.apple.com/kb/HT3964

My ipad is taking restart automatically and screen is fully balck and showing only apple logo.please give me solution for that

my ipad is taking restart automatically and screen is fully balck and showing only apple logo.please give me solution for that

Have you tried a reset first? If it works, you won't have to go through the restore process.
Hold down the sleep (upper right hand top) and the home button at the same time. A slider will appear. Ignore it and keep holding down the buttons. The Apple logo shoud appear. Then your ipad might work again. It takes a good 15 seconds. You will not lose anything on your ipad.
If you try it a couple of times and it doesn't work, you might have to go through the restore process as has been suggested above. But follow the steps so you don't lose your data.
Hope this helps.

Why are some of my keys not working when I put a bit of pressure on it?

Hi there, since 4 months ago I've noticed that my a, q, 1, backspace, and volume buttons do not work when theres a little bit of pressure on or under it. It kind of bothers me because I cant lay in bed and do my things, I have to put it on a table. So my question is, why is this and how can I fix this?
5 or more weeks ago, I can't remember, my keys did suddenly work when there was a bit of pressure on / under it, but I don't know how..
I'm running OS X Mavericks 10.9.4
Processor: 1.3 GHz Intel Core i5
Memore: 4 GB 1600 MHz DDR3

What is your operating system? Reader version? How do you convert to PDF?
You write that "some" of the links don't open; what's the difference with links that do open?

The remote does not work, when i turn the tv on I see the apple tv and the itune icon on the screen

the remote on apple tv does not work,when i turn on the tv Isee the appletv and the itune icon on the screen.

Did you do a software update?
AppleTV is unable to start properly. You need to connect to a computer running iTunes as detailed here:
Apple TV (2nd and 3rd generation): Restoring your Apple TV

Ipad does not work when you tap "continue" or "next"

the "continue" buttons do not work. When I sign in for instance to my bank and put in my username and then it says "continue" that button does not work. I also happens on buttons that say "next". Any one know if this is a flaw?

Please be wary of vacuuming the speakers, this can lead to damage of the speaker due to the force/static this can generate. Normal heat generated by usage should be enough to dry out the speaker in a short period fo time.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Pause / Resume button combination not working when set to display for "rest of project"

Good day,
I have created a set of four objects on slide2 of my project
1. Smart Object rounded rectangle with text "(playing) - CLICK to Pause" [this is the graphic the user sees]
2. Smart Object rounded rectangle with text "(paused) - CLICK to Resume" [this is the graphic the user sees]
3. Smart Object rectangle, transparent, used as button, set to not display in project - btn_Resume
4. Smart Object rectangle, transparent, used as button - btn_Pause
A. Script assigned to btn_Pause hides btn_Pause and the "CLICK to Pause" graphic, shows the btn_Resume and "CLICK to Resume" graphic, and pauses the project by setting the system pause variable to 1
B. Script assigned to btn_Resume hides btn_Resume and the "CLICK to Resume" graphic, shows the btn_Pause and "CLICK to Pause" graphic, and resumes the project by setting the system resume variable to 1
C. All items are set to display from the beginning of slide2 for the "rest of project"
On slide 2, the buttons hide/show and pause/resume behaviors work correctly.
On slide 3, the correct initial button and graphic appears, and the click sound works when clicked, but no behaviors (show/hide/pause) occur until a good amount of time into the slide: you can click all you want for 20-30 seconds, but nothing works except the click sound. Eventually, the behavior will work.
On slides 4 and following, the correct initial button and graphic appears, and the click sound works when clicked, but no behaviors EVER work.
If the behaviors NEVER, EVER worked, I would keep looking for what I did not have set correctly, but the correct working on the slide where they are set, delayed behavior on the next, and no behavior on the remainder of slides following has me stumped.
Captivate version 6.0.1.240
Windows 7 OS
I hope I'm missing something obvious here, and I'm more than willing to face-palm if you tell me . Otherwise, I have not been able to find any setting that makes any difference. I would REALLY rather not duplicate the buttons and scripts on every page of the project. Given the blog posts I have seen saying this method should work just fine, I'm hoping there is a side quirk somewhere that I'm missing.
Thanks for any help you can give.

Without clouding with too much explanation, this technique arose out of a need to deal with (in a different project) objects that were grouped, and wanting to deal with the groups in as simple a way as possible, allow for easy swapping of group assets, and having a few buttons do multiple things. The idea of being able to have multiple interactive buttons stacked on top of each other while appearing for the rest of the project led to trying this simple construct before trying something more complex.
You are correct, that there is a simpler solution, which we ended up using because we were not able to get two interactive buttons stacked on top of each other while displayed for the rest of the project to work properly (although that is SUPPOSED to work, as far as I understand).
Here's what we ended up doing:
A) Two smartshapes used as messaging graphics
B) A single (one) interactive smartshape used as a button
C) A conditional action to pause/resume and show/hide the appropriate messaging graphics
D) All three objects (A&B) stacked, B on top.
E) All objects set to always appear on top, and to display for rest of project.
Our hypothesis, then, is that you are not able to stack interactive objects on top of each other and then display for the rest of the project.
If anyone has evidence to the contrary, we would, gladly, take a look.
Thanks for your interest Lilybiri, and for your input.
Best regards,
Hank

Why does diadem intellisense not work when using scriptinclude or for global object

I have a script with a different classes in it (scripted 1). When I create an object of a class in the script 1 intellisense works. Intellisense is when you type name of the object created from a class it shows all the possible variables and functions contained in that object. But when I write another script and use scriptinclude(scripted 1) the intellisense does not work. I also tried a global object and intesllisense does not work. Is there a way to get intellisense to work when using scriptinclude? I am working with version 2012.

Here is more information on the issue.
I have a script with a different classes in it (scripted 1). When I create an object of a class in the script 1 intellisense works. Intellisense is when you type name of the object created from a class it shows all the possible variables and functions contained in that object. But when I write another script and use scriptinclude(scripted 1) the intellisense does not work. I also tried a global object and intesllisense does not work. Is there a way to get intellisense to work when using scriptinclude? I am working with version 2012.
'Test.vbs
class test
    public function test1()
         msgbox("test1")
    end function
    public function test2()
         msgbox("test2")
    end function
end class
'now create a object of the class
dim oTest
set oTest=new Test
'now when you type oTest. you get the following functions to choose from
oTest.test1
        .test2
Now if you remove the object from Test.vbs and create a main program with scriptinclude(Test.vbs) it will not show the two functions
'Main.vbs
Option Explicit 'Forces the explicit declaration of all the variables in a script.
call scriptinclude("c:\1atmp\Test.vbs")
dim oTest
set oTest=new test
'now when you type oTest. it shows none of the functions in the object oTest
oTest.

Why does my ipad no longer ping when I put it on charge?

I recently was given a new charger from apple for my iPad 3 as the old on wasn't working and since getting the new charger my iPad no longer makes the ping noise when I plug it in to the power supply. Why is that and is there a way of turning it back on? Thanks

I recently was given a new charger from apple for my iPad 3 as the old on wasn't working and since getting the new charger my iPad no longer makes the ping noise when I plug it in to the power supply. Why is that and is there a way of turning it back on? Thanks

Hi! I purchased my ATV in Miami, but I live in Argentina. I have not been able to get the device running on any TVs. When I plug it in, it briefly shows the apple logo, then a sign saying no signal, check power cords and power source or sthg like that.

Hi!
I purchased my AppleTV in Miami, but I live in Argentina.
I have not been able to get my device running correctly, and altough I've read tons of things online, I still have no solution to my problem.
Here's the thing: after everything's plugged in and ON, I see the Apple logo briefly, then the TV displays a sign that says no signal, check pwoer cords and power source.
But everything is plugged in and connected properly, otherwise, I doubt I'd be seeing the apple logo, right?
I tried changing the HDMI cable, reversing the ends, switching ports, hard resetting the ATV, and trying a different TV. No luck.
I read there is some issue with Samsung TVs, and most LED and LCD tvs down here are Samsung.
On the other hand, I cannot return it or exchange it, since I bought it in the states.
Oh! One of the tvs I tried it on displays a little sign that reads "connected at 1280x720 @60hz", and only THEN, goes to the "no signal" sign.
Please!!! I am being driven up the walls here.... HELP!!

Try this:
Change the Apple TV resolution:
Press and hold the Menu and Up button on your Apple Remote for six seconds.
The Apple TV will automatically cycle to the next resolution at approximately 20 second intervals.
Press Play on the Apple Remote to keep the current resolution or Select to manually cycle to the next resolution.

My cursor does not open many links. If I get a message on Linkedin the "Accept" rectangle does not work when I put my cursor on it.

M cursor changs from an arrow to the text (tall I) icon when I move it over links and "unsubscribes" and I can't respond to either Facebook or Likedin buttons.
Often if I get a link in an e-mail message my cursor will not open the link. The arrow changs back to the txt cursor and the link won't open. Help!
people send me important mesage telling me to hit a link to open something but my cursor won't open the link.???

First check your trackpad settings to make sure all is correct.
/Library/Preferences. Trash the com.apple.finder.plist file.
Disconnect all peripherals from your computer.
Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
Restart your computer when done.
Repair permissions after you reach the desktop-http://support.apple.com/kb/HT2963 and restart your computer.
Empty the trash.

HT2736 my iTunes music card is not working when i put my code in it tells me my card is not actavaded

my iTunes gift card is not working

In that case the procedure assuming it is a PAYG phone is to get an o2 PAYG sim, put £20 on it and then make a few calls making sure you leave £15 on the sim to pay for the unlock. Then there is an online unlock request form on the o2 site just fill this in. It takes between 1-14 days and you get a message from o2 telling you how to complete the official unlock through iTunes.
I got my o2 unlock in nov 09 so this is not just opinion.

My Ipad 1 is not working. when i put it for charging it shows blinking apple logo

Similar Messages

Maybe you are looking for