My iPad 2 goes into restore mode almost dailyand can't restore it anymore error 1603

My iPad 2 goes into restore mode almost daily. I usually just restore and sometimes use the iCloud backup. This time, my iPad cannot restore. I have gotten the error message 1603. I have the latest version of iTunes. PLEASE HELP ME

Hello Sean,
It sounds like you are constantly needing to restore your phone because it keeps going into recovery mode. Usually putting a device into recovery mode and restoring it can help isolate an issue to your iPhone hardware if an issue persists afterwards. I would try manually putting it into recovery mode and restoring it 1 more time:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
If that does not resolve it the symptoms indicate to me that it is a hardware issue causing this to happen and would seek service for it:
iPhone Repair - Other Repairs
https://www.apple.com/support/iphone/repair/other/
Thank you for using Apple Support Communities.
All the best,
Sterling

Similar Messages

  • IPad goes into recovery mode every time I power up

    Is this normal?  What could be wrong?

    It is by no means normal. When you say that it goes into recovery mode, do you mean that you have to restore the iPad every time that you turn it on?

  • My iPhone 4s randomly went into recovery mode and I can't restore it with iTunes...what do I do?

    Last night my iPhone randomly went into recovery mode on me. Just before I went to sleep a bunch of static lines appeared across the screen. The screen went dark and a few seconds later the Apple logo appeared. A few seconds later is disappeared. A few seconds later it came back. So on and so forth. I thought I had turned it off and was going to deal with it in the morning, but when I woke up the iPhone still just had the Apple logo going on and off again.
    I've tried everything today. All the different button hold methods out there. I've tried to sync it to iTunes but the same **** keeps happening over and over again.
    A message pops up saying "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes." So I press OK. Then I press the "Restore iPhone..." button on iTunes. It asks me if I'm sure I want to "restore it to the factory settings" and I click "Restore and Update". It then says that its "extracting software", "preparing the iphone to restore", "waiting for the iphone", then "verifying iphone restore with Apple". As this is going on the "connect to iTunes" sign is shown on the screen of the iPhone. When the "waiting for the iPhone" part starts, my screen goes black, then the apple logo pops up. The "verifying iphone restore with apple" comes on the iTunes and the status bar appears underneath the Apple logo on my phone's screen. It sits there for a couple of seconds with no progress and then the screen goes black. Then iTunes has the same **** message saying "The iPhone 'iPhone' could not be resotred. An unknown error occured (9)."
    I've gone through this process countless times in the past few hours and have done everything that apple support has told me. The windows system is fully updated. So is the iTunes. I've restarted the computer. I have no idea whats wrong and its making my blood boil.
    A couple of notes about the phone:
    It's over a year old. It's never had water damage. It was nearing the max capacity of its internal storage. This has never happened before. I keep it in an Otter Box. I had very little problems with the phone. Lately a couple of apps like snapchat and the barstool sports app were taking a little longer to open up or would randomly close out and sometimes my camera would take a while to get going. But this problem is just ridiculous and completely rendered the phone useless.

    Hello Sean,
    It sounds like you are constantly needing to restore your phone because it keeps going into recovery mode. Usually putting a device into recovery mode and restoring it can help isolate an issue to your iPhone hardware if an issue persists afterwards. I would try manually putting it into recovery mode and restoring it 1 more time:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/HT1808
    If that does not resolve it the symptoms indicate to me that it is a hardware issue causing this to happen and would seek service for it:
    iPhone Repair - Other Repairs
    https://www.apple.com/support/iphone/repair/other/
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Suddenly my 3GS enlarges the screen OR goes into rearrange mode. What can fix this?

    This happened in the blink of an eye. I did a restart, a restore, and nothing is working.  The display comes on as normal then takes a slight jump so that some of the display is outside the screen.  If I edge to press a button, the screen moves and alows the press, bu then another part of the screen is not visible. The other annoyance is apping the calendar, or the phone, or addresses, or anyhing else will shift the phone into wiggly rearrange mode. I have to press home then tap the icon once again. Sometimes this happens 2x before I get the app to come up.  One other thins has started happening, when typing, sometime a letter will hold and a row of variations ofthe letter appear as tabs across the top, like oomlaut, or tilda over theletter or whatever.  HELP!!!

    Try resetting your iPhone by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.

  • My iPhone 5 is restore mode but I can't restore with itunes, please help me,when firewall updating then iphone do not response and show same problem

    Hello... Please help me... how can i resolve this problem... please help... when i update this device then this is problem is shown and after update ios I could not use iphone for a single days...

    See "What does iTunes back up?" here:
    http://support.apple.com/kb/HT4946
    That is what you will get back.  You will lose other things (example, mail messages).

  • IPad 3 goes into recovery mode after every update

    I purchased an iPad 3 in September 2012. When I installed iOS7, the iPad went into recovery mode and had to be restored to factory settings. Yesterday, I tried installing iOS 7.0.3 and it did the same thing, and I had to restore it from a backup (which I was smart enough to make before installing this update). Before installing iOS 7.0.3, I was having problems with the iPad randomly going to the black apple screen for a few seconds and then returning to normal. Any idea what is going on? Do I have a v

    I had this problem with my wife's iPad when I updated to 7.0.3 via OTA. It was easily fixed for me, and I assume it should work for everyone else.
    It appears that sometimes during installation of the OTA update to 7.0.3, it gets stuck in recovery half way through.
    You can connect it to iTunes and restore it, which will wipe it, OR you can download TinyUmbrella and kick it out of recovery. Once you do that, the installer should complete normally (it did for me).
    1) Download and install TinyUmbrella for your PC/Mac.
    2) Make sure iTunes isn't running and connect your device via USB.
    3) Open up TinyUmbrella. Your device should show up on the left. Click on it and then choose "exit recovery".
    4) Profit.

  • Mac Pro randomly goes into sleep mode

    My (mid 2010) Mac Pro, OS X.6.8, randomly goes into sleep mode and I can't wake it, have to power it off and reboot. Just started to the best of my knowledge Friday (Jan 6, 2012) I've had it happen surfing the web in Safari, while working on an illustration in Adobe Illustrator, while running Apple Hardware Test, using 23" LCD connected by HDMI and DVI-D, Disconnected monitor and connected 12" Cintiq (LCD Tablet).
    The monitor goes black, says "there's no signal coming from your computer", none of the keys will wake it. I have to hold down the power button until it turns off then power it back up. The time between the sleeps varies, 38min, 1hr 34min, 5min, 2hr 17min, 12min, etc. I disconnected everything (except keyboard, mouse, monitor) still the same. Opened and removed the ATI Radeon HD 5870, and noticed the PRAM battery, replaced it with a new one, thought that fixed it, worked for a long time then it happened again.
    Tried Apple Hardware Tester again, it said everything is fine, ran it again an error popped up: 4SNS/1/40000000:Te1S-99.364, wrote it down then it slept.

    The next time this happens open your mac and see if there is still a fan running.  If so you are not sleeping, you are in a thermal cutoff.  Keep you mac cover off.
    Now reboot as you always do.  Take a look at the fan in your 5870.  Is it spinning?  If so, try to keep an eye on it and see if you can "catch" it not spinning. 
    When the fan doesn't start, or if it does then stops, the card will overheat and the machine will go into thermal cutoff.  The amount of time is variable.
    I speak from experience.  I am currently on my third 5870 video card.  Both the previous two had this fan problem.  The only wrinkle in my theory for you is that I wouldn't expect more that, say, 15 minutes of up time at the most, not hours like you got.  But it may be that your card is starting ok, but stops sometime later.   I chalk it up to the lousy fans Nvidia uses in the 5x70 cards.
    FWIW, if you happen to catch the fan stopped before the machine goes into thermal cutoff you can give it a little nudge with your finger to get it going again.
    I recommend one of the various temperature monitors.  I use iStat Menus and display some key temps in my menu bar.  Of course after going through two of these cards I am a bit paranoid!
    Some other temperature monitors:
    iStat Pro
    Temperature Monitor
    Hardware Monitor
    Note, after typing all this I also realized you got a AHT 4SNS error. I would run AHT again to see if you get that error again.  If so that means "Check Main Logic Board" and you may have a more serious hardware problem than just a video card!  So my other recommendation is that when you machine fails again look inside for any lit diagnostic leds.  There's some near the dimms but there are others on the board as well.

  • IPhone 3G goes into Recovery Mode after every restore

    Every time I restore my iPhone 3G, it goes into recovery mode right after an error-less restore has been completed. Yes, I've tried using tools such as TinyUmbrella and RecBoot and iRecovery. The device was not jailbroken when I tried to update it to 4.2.1 yesterday. They all reboot the phone and just throw it back into recovery. I have no idea what to do. Searching is futile. I thought I might as well do what I almost never do and ask these communities for support.
    I hope they don't disappoint.

    I had this problem with my wife's iPad when I updated to 7.0.3 via OTA. It was easily fixed for me, and I assume it should work for everyone else.
    It appears that sometimes during installation of the OTA update to 7.0.3, it gets stuck in recovery half way through.
    You can connect it to iTunes and restore it, which will wipe it, OR you can download TinyUmbrella and kick it out of recovery. Once you do that, the installer should complete normally (it did for me).
    1) Download and install TinyUmbrella for your PC/Mac.
    2) Make sure iTunes isn't running and connect your device via USB.
    3) Open up TinyUmbrella. Your device should show up on the left. Click on it and then choose "exit recovery".
    4) Profit.

  • HT4972 I have an ipad 2, yesterday I updated my ipad going in to settings software update, then the ipad went into resore mode saying it needs to connect to itunes. I did that and itunes said it was goingo to do a resotre and I lost all my info, pictures,

    I have an ipad 2, yesterday I updated my ipad going in to settings software update, then the ipad went into resore mode saying it needs to connect to itunes. I did that and itunes said it was goingo to do a resotre and I lost all my info, pictures, contacts. Is there a way to recover all my info?

    You should be able to reconnect to iTunes and then you should see an option to restore to your ipad from your last back up in iTunes.

  • Streaming audio from my IPAD to my Apple TV from Rhapsody application.  when Apple TV go into Screen Saver mode, about 5 minutes after that it stops playing the Audio Stream and goes into Sleep mode.

    I am Streaming audio from my IPAD to my Apple TV from Rhapsody application.  when Apple TV go into Screen Saver mode, about 5 minutes after that it stops playing the Audio Stream and goes into Sleep mode.  I am using the Optical Out from the Apple TV to my receiver, the Apple TV is hard Wired to the Network, the IPAD is Wirelessly attached to the network (it continues to play the Audio Stream).  When the Apple TV is turned back on it resumes playing once I manual select it for output from the IPAD.  All device are on current releases of software.  I have no Video hooked up to the Apple TV.  How do I correct this?

    Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
    You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
    Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
    There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.

  • TS1591 My iphone 4 randmonly started going into recoveery mode when i was trying to download ios 7.1, and now the apple logo will come one and then fade to black and continue this process. My iphone wont restore either and will get the 3194 error message.

    My iphone 4 randmonly started going into recoveery mode when i was trying to download ios 7.1, and now the apple logo will come one and then fade to black and continue this process. My iphone wont restore either and will get the 3194 error message.Help please!

    Hello chindeepchow,
    Thank you for using Apple Support Communities.
    For more information, take a look at:
    Resolve specific iTunes update and restore errors
    http://support.apple.com/kb/ts3694#3000
    Resolve communication issues
    Related errors: 17, 1004, 1013, 1638, 3014, 3194, 3000, 3002, 3004, 3013, 3014, 3015, 3194, or 3200. These alerts refer to gs.apple.com, say "There was a problem downloading the software," or say the "device isn't eligible for the requested build."
    Check the hosts file or TCP/IP filtering, which might cause communication issues between iTunes, ports, and servers.
    Have a nice day,
    Mario

  • IPod says to use iTunes to restore but keeps going into disk mode.

    So whenever I reset my iPod, a screen pops up that says to use iTunes to restore it but when I plug the iPod into the computer, it goes into disk mode and iTunes doesn't read it.

    Already tried another USB port, still nothing.
    I don't have another PC to check, I only have one which is the one not working with my iPod.
    It appears under my Computer, just not under iTunes. Plus, the iPod classic troubleshooting assistant doesn't work because I can't restore since it can't come up onto my iTunes! Even my iPod says "Use iTunes to Restore" once in a while, but I plug it in & I'm not able to restore it since it won't come up under iTunes.
    Please help

  • When trying to restore my Iphone it goes into recovery mode

    I recent just upgraded my IPhone 4s to 5s.  When I synced it to my computer it transfered eveything from my old phone to the new one which I didn't want.  So when I tried to restore it to factory settings it went to recovery mode.  I can get it out of recovery mode but it just goes back to way it was.  How can I restore it with out going into recovery mode.

    we have same problem bro .. i dont know what to do.

  • IPod goes into recovery mode when plugged in, and forces me to restore

    Basically what is written above ^^ is what is happening to my iPod Classic 80GB. It hasn't done this until recently, and every few days or so when I go to sync new songs onto my iPod, it goes into recovery mode and says that the iPod must be restored. Now, normally this wouldn't be a problem, but when you have an 11,000 song library that takes around 4 hours or more to sync, it gets really under your skin.
    I'm running Windows Vista, any help?

    I just purchased a Classic iPod, and two days later it is stuck in this restore loop. The iPod worked fine until the restore was complete. When unplugged from the computer, it responds fine, but now cannot sync at all to put media on the device.
    Current machine is WinXP SP2 (work machine). It is also happening on Win7 desktop, 13inch Macbook (OS 10.6.3), and Mac Mini (OS 10.6.3)(personal machines).
    Does this appear to be a faulty device?

  • My iPad randomly goes into sleep mode while I am using it?

    All of a sudden, when ever I use my iPad 2 it goes into sleep mode. It did it three times while I typed this message.  As I am running an app it will just go into sleep mode with out me doing so and I have to press the home button to wake it up. Doesn't matter what app I am running. I have 4gb of storage available.  Most of the time it brings me back to the app I was using when it went to sleep.  Has anyone else suffered this issue. I am running the latest iOS 6.0. 

    What "issue"? This is perfectly normal. By default, all (fairly-recent) Apple products will go to sleep if left idle for a certain period of time. This is NOT normal, however, if in the app, you are pressing buttons on the screen. If you are doing something like reading, for example, try setting your iPad to not go to sleep that quickly.
    (Google how, I don't completely remember.)

Maybe you are looking for

  • How Can I download a Windows 8.1 ISO file to my MacBook Pro for a VMWare Installation?

    I am attempting to install Windows 8.0 into a virtual machine with VMWare Fusion 6.02.  I've got XP running on an older MacPro so with VMWare so I'm somewhat familiar with how this works but by no means an expert.  Foolishly I purchased a license for

  • Can't get sound out of imac

    I am a musician and am trying to mix down some tracks off of a hard disk. I have a hard disc recorder and a mixing board that i am running into an M-audio Firewire solo. I have the signal flow going into the firewire solo and then into my mac. when i

  • Redownloading Acrobat 9.0 Standard

    I do computer work in my home. A customer needed a new hard drive. I want to download and install Acrobat for her. She does not have a backup copy unfortunately. According to her the software was purchased after she got the computer so it's not OEM.

  • Internal Software Error in MIG

    Running Windows XP SP 3 Labview 8.2 Error:  Error -229665 occurred at DAQmx Create Channel (DO-Digital Output).vi:1 Internal Software Error occurred in MIG software. Please contact National Instruments Support. No new devices installed.  When opening

  • Session Problem in Login and Logout

    When the user successfully login to the system, a session would be created the code in LoginServlet:      HttpSession session = request.getSession(true);      session.setAttribute("username", username); then when the user try to logout, the sesssion