My Ipad 2 is disabled and nothing works
My kids tried to get on the Ipad and entered the wrong code to many times. It says I have to connect to Itunes. I have now followed the steps to do this 3 times and it fails every time. I am trying to do the recovery mode where you turn it off and press the home button. It starts the Ipad software update but after 20 minutes it goes away from the screen that shows the itunes logo and back to the main screen that tells me the Ipad is disabled. Then the software update fails to completly download. I have the most up to date version of Itunes.
Is this how you do it?
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.
Similar Messages
-
HT4061 My iPad is disabled and nothing will get me passed this, not even a restore or factory reset
My iPad is disabled and nothing will get me passed this, not even a restore or factory reset. The restore through iTunes won't complete because it says there is a passcode on the iPad and cannot complete, but I can't get to the passcode screen to enter anything. Anyone have any suggestions?
See this support document for explanations and instructions on how to deal with update and restore errors. Get help with iOS update and restore errors - Apple Support
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Confirm that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support. -
Hey, my ipad is disabled and i cant open. i tried connecting it with itunes in recovery mode to restore it but it wont work it doesnt show and options itunes doesnt detect my ipad in recovery mode. what do i do know? please help!!!
If you followed these instructions and you were unable to enter recovery mode, I'm still leaning toward a hardware problem. Also, since you have IOS-7, read this. It might help.
-
Using Tiscali Webmail with Firefox 6. If I try and delete an email the Ok and Cancel buttons are disabled and nothing happens, have to use F5 to take me back. IE8 works so is this a compatibility issue?
It appears OP solved the problem: [/questions/874744]
-
My iPad is disabled and it says to connect to ITunes with my Mac. It still is not working.
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times. -
My entire iTunes library is missing on my two non-Apple computers. My libraries still exist on my iPad and iPhone though. I tried deauthorizing and then reauthorizing my devices, uninstalling and then reinstalling iTunes and nothing works. What happened?
See Empty/corrupt iTunes library after upgrade/crash or
Recover your iTunes library from your iPod or iOS device.
tt2 -
I have an ipad mini that won't power on. It was turned off to charge overnight. In the morning it was warm and now won't turn on no matter what I do. I've tried resetting using the power / home button combination and nothing works.
If you have owned the device, as in purchased from Apple, less than a year then there will be no charge to repair, or most likely, replace the device. If you have had the device more than a year you will be charged an out of warranty cost for replacement ($219 I think) and that is much cheaper than a new device. If you have Applecare+ then you have an additional year of coverage and the replacement will be $49 or $79 depending on when you got the Applecare.
-
My iPad won't connect to my wifi anymore. Was using it and it just quit. It is not my wifi because my daughter's iPad works just fine. I've turned it off and back on, reset, forgot this connection and nothing works. Help???
1. Turn off router for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings -
My iPad is disabled and I am unable to get it to work. How can I fix this?
My iPad is disabled and I can't figure out out to get it fixed. The original Apple ID that was set up on the iPad is no longer active and I'm not sure if I ever changed it. Can anyone help me???
Finding your Apple ID or resetting your password
-
I have activated the passcode lock on my iPad sometimes ago and now I foregot it, I entered several passcode but non was correct, now the iPad nis disabled and would not connect to the iTunes. what can be done to unlock my iPad?
If you've forgotten the passcode then you will need to connect the iPad to the computer that you normally sync to and you should then be able to reset the iPad and re-sync your content to it (http://support.apple.com/kb/HT1212) - you may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808
-
Please help!! ipad is disabled and will not do a hard reset to go into recovery mode.
i cannot do a force reset... When i hold in the home and sleep/wake button nothing happens, I have tried these same steps over and over again. Neither the apple or the itunes logo ever pop up.. The screen just stays black. I recently replaced the digitizer after my son cracked the screen. I have made sure that nothing was injured during repair. I did put the digitizer ribbon in wrong and then the screen was not working correctly. I had put the ribbon in backwards. So after the first wrong installation of the digitizer, i tried to unlock the screen with my passcode but it obviously wasn't working.. i would touch the number for the passcode but the screen would respond somewhere else..so i kept getting the passcode wrong and then BAM! Ipad disabled.. so i took a break from the frustration... When i returned to my ipad i took it back apart and thats when i realized that i had the digitizer ribbon in backwards, so i fixed it and replaced the screen once again.. But now the ipad is disabled, and for some reason it will not respond when i try to shut it down all the way, no red slider at all...so i bout a apple data transfer cable and i tried to connect it to itunes and hold the buttons like i read to do in the article, and my computer recognizes that my ipad is there,,, it tells me that i have to allow access and to respond on my ipad.. but sadly i cannot.. nothing appears on the ipad.. it stays a black screen and then when i lt go the "ipad is disabled" screen comes on.....
Then i read online that i could restore from icloud.com, so i go there, i sign in just fine but my ipad is not listed in the devices there either... it says " No Devices, You must be signed into iOS8 settings or Mac OS Yosemite system preferences to see devices."
And i dont believe the ipad is up to date, it had been unused for about 2 months, until last week when i attempted to fix it so im sure the operating system is old :-(
So im totally lost, I dont have a clue what to do to get my device recognized. I would really appreciate any help that anyone can give,, Thank you so much in advance!!!
Ipad 2 wifi 16gbIf recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
My IPad is Disabled and can't get it on.
My IPad is Disabled and says connect to Itunes. I don't know how to get it working again.
Epic Dylan wrote:
i don't have a mac
You don't need a Mac. You can use a PC running Windows.
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
If you can’t update or restore your iOS device
http://support.apple.com/kb/ht1808
iPad Stuck in Recovery Mode after Update
http://www.transfer-iphone-recovery.com/ipad-stuck-in-recovery-mode-after-update .html
How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
HT1414 ipad is disabled and wont restore
Son's iPad Mini - he fogot his passsword & now the device is showing "iPad is disabled" and I cannot get it to restore. Tried to go through Recovery Mode but it gets stuck with a message that says "To allow access, please respond on your iPad" but I cant do anything with the iPad except power it down....
How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
HT1212 my ipad is disabled, and i can try again in 22 688 540 minutes.. What to do?
my ipad is disabled, and i can try again in 22 688 540 minutes.. What to do?
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
I plug my iphone 3gs into my laptop and it no longer syncs with my iTunes. I've tried all the trouble shooting methods and nothing works. My iPhone doesn't appear on iTunes or under "My Computer." Does anyone know how to fix this?
If AMDS is running, you are using a USB port directly on the computer and not a hub, you have disconnected other USB devices except keyboard and mouse, you have completely uninstalled and reinstalled iTunes as described in http://support.apple.com/kb/HT1925, You have tried cleaning the connector on the bottom of the phone, you have tried a different cable, you have installed the latest USB drivers for your computer, you have disabled your antivirus and firewall, you are running as an Administrator account and you have tried creating a new user on your computer and connected when logged in as that user then you have exhausted my knowledge. The only other thing to try is a different computer. If it isn't recognized on a different computer you have a hardware problem. Good luck!
Maybe you are looking for
-
TableView - How to update a running balance column after any other column in the view is re-sorted
To keep this simple and to illustrate a problem that I am trying to solve let's say we have a domain class that contains an income per day. This class has two persistent properties - populated from a database table - date and income. And there is one
-
ERROR: JBO-26048 while createing a record.
Hello, I have a table called ActivityTracker which has few Foreign Keys and one among them is for Activity_SubType (refering a table called Activity_Subtype). I am trying to insert a record in the ActivityTracker table using the following code: Entit
-
Where do I put my 'rated' images?
Ok, I've taken the pics, they're on the imac/aperture, I've gone through them and rated them either 4 or 5 stars - where and how do I put them next to work on them? Thanks
-
I will try to give as much info as possible,I have a sound blaster li've xgamer card which has fi've jacks in the rear including the digital outI am going to a reciever which is somewhat new but does not have digital in. Therefore I need to hookup wi
-
Hi, I have had some corrupt contorl file (well i dont really know what im new to all this) i have spent 4 hours today trying to get my database up and running again, with a million people telling me totally different things... I figured it will be le