My iPad 2 will no longer connect to the internet after iOS 6 update

HELP!! My iPad doesny connect tot the internet anymore. I down loaded iOS 6 today (9/19/12) and now it doesnt connect tot the internet anymore.

Hello dchoffa,
Thank you for using Apple Support Communities!
I would start with this troubleshooting from the article named:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Be sure you're in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
Tap and Forget this Network.
Try to connect to your desired Wi-Fi network.
Note: You may need to enter your Wi-Fi password again if your network requires one.
Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
If the above troubleshooting does not resolve the issue, I would next try the troubleshooting in one of the other sections down toward the bottom that fits your scenario.
Regards,
Sterling

Similar Messages

  • Since updating my ipad it will no longer connect to the internet

    since i've updated my software on my ipad it will no longer connect to the internet. my husbands iphone will not connect either. my laptop connects immediately and my internet signal is full strength. is there something we are missing?

    Hello dchoffa,
    Thank you for using Apple Support Communities!
    I would start with this troubleshooting from the article named:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    If the above troubleshooting does not resolve the issue, I would next try the troubleshooting in one of the other sections down toward the bottom that fits your scenario.
    Regards,
    Sterling

  • My ipad will no longer connect to the internet. Everything else does.

    My ipad 1 will no longer connect to the internet. Everything else does. and nothing new was done to the ipad. It's running ios 4 and was fine since the day it came out.

    Emma-
    In Safari, press on the Bookmarks icon and select History.  Then press on Clear History at the top of that menu, and see it there is any improvement.
    If not, try unplugging your WiFi router for a few seconds.  Then reset the iPad's network.  Go to Settings-General-Reset-Reset Network Settings.  You will need to reconnect the iPad to WiFi.
    Fred

  • My Mac Book Pro suddenly will no longer connect to the Internet at my house. Help?

    My Mac Book Pro suddenly will no longer connect to the Internet at my house. My son's MacBook connects just fine. My MacPro connects at work, at Starbucks, etc. just fine, but not at my house. My son's however has no problem whatsoever. I assume that since his computer connects that the router and modem is not the problem. And since my computer connects everywhere but here . . . . it is not a hardware issue. When directly connecting my MacBook Pro to the modem or router the problem was the same. . . no connection. Help?

    From the menu bar, select
               ▹ About This Mac
    Below the "OS X" legend in the window that opens, the OS version appears. Click the version line twice to display the serial number. If the number is missing or invalid according to this web form, take the machine to an Apple Store or other authorized service center to have the problem corrected.

  • Will no longer connect to the internet

    All of a sudden Adobe Digital editions will no longer connect to the internet.  It was fine before last Tuesday. Check internet settings and firewall and nothing helps. Why is it doing this and how can we fix it.  Windows 7 - 64 bit

    Did this [[Cannot connect after upgrading Firefox|start after upgrading firefox?]]
    Generally if Firefox can't connect, but other applications can, it's a configuration problem with a [[Firewalls|software firewall]], either one you installed yourself, one that was included with other security software, or the built-in Windows Firewall.

  • WRT54G ver. 6 can no longer connect to the internet after reset

    I reset my WRT54G ver. 6 to clear the password, and now I can no longer connect to the internet with it. I can see the router itself from my PC, but that is all. I've followed the directions here for connection problems, but I can't seem to get an IP Address for it in the Web Configuration tool. Anybody have any thoughts?

    Since you reset your router, you need to reconfigure it back again. try the online utility that automates the configuration. download Easy Link Connect utility at www.linksys.com/connect then download "Netset" and follow instructions.
    if not Easy Link connect didnt work then you need to do the configuration manually.
    1. check physical connection modem should be connected wired to internet port of the router then PC to numbered ports of the router.
    2. Brighthouse i believe is cable connection, right? try power cycle your devices (turn off modem and router then turn on modem 1st then router next). check if your online.
    3. if not. check PC ip. click "start" then "run" type in "cmd" then press "OK". the command prompt should pop-up. type "ipconfig" and check IP and gateway. you should be getting an ip: 192.168.1.x and gateway: 192.168.1.1
    4. access router. open IE, then type in http://192.168.1.1 on address bar.
    5. you will be prompted with username and PW. "admin" is the default password. on setup, just below are subtabs. select "MAC address clone". in it, set "mac clone" to "enable" then click on "clone" then "save settings".
    6. power cycle devices again. try to go online
    note: if you dont have latest firmware. try updating if needed
    Message Edited by whodas on 11-07-200601:28 PM
    it is EVIL enough for GOOD men do NOTHING.

  • New ipad will no longer connect to the internet.

    This is not a network problem - all my other devices work fine and are connecting (including iphone, MacBook, girlfriends "new" ipad). Mine worked fine for months then suddenly, i get the wifi signal but in settings, you just see the spinning gear - not the check mark. When you try to open a web page, it just says "not connected to the internet"
    This is the second time this has happend with the 3rd generation ipad.  I had an ipad 1 for years and no probs, then i upgraded to the new one and it stopped connecting after a month or two. PC World said they had a few people report the same problem so just gave me a refund. Bought a replacement new ipad at Apple and now the same thing has happened to that one.  I guess i could take it back to apple but surely there is a fix for this?

    I should add that i have also done:
    - reset (holding two buttons)
    - updated software to latest IOS
    - done a full restore to original settings
    None of this has solved the problem.

  • I recently installed the 5.5.3 AirPort Utility update and my airport will no longer connect to the internet.

    I recently updated my macbook's AirPort Utility to 5.5.3 and it will no longer connect to wireless networks.  First let me explain everything I have done already, I have reset my router, and tried on other's (my friends and my schools) networks.  I have been able to succesfully connect to my friends wireless (router is made by netgear), but when i try to connect to my network (WRT54G linksys router) and my schools network (im unaware what they use for routers) I am unable to connect, and my AirPort will proceed either state it does not have an IP address and will assign itself one and will not connect to the internet.  It will connect to the network with an IP, but will be unable to connect to the internet with the browser claiming DNS lookup failure. 
    yes, I have deleted and changed my location,
           deleted the selected service.
           tried resetting my router
           cleared my PRAM / NVRAM
           installed the newest firmware onto my WRT54G
           Renewed my DHCP lease
           made sure my Configure IPv4 is using DHCP
          and theres a few more but i'm forgetting them.  
    Any suggestions on why the 5.5.3 update might of screwed up my airport?

    If everything else is connecting with no issues, I would go into the wifi setting on the iPad and redo the info there, user, password and anything else related to your wifi at your house.
    It is possible whatever he reset may have reset something to default setting which will not allow it to connect. If you need too then verify the wifi setting by comparing it with another device setting that works on your home network.
    Good luck

  • My 3000H will no longer connect to the internet via my cable modem - help please.

    I have 3 computers and a media server on a Linksys router with a Comcast cable modem. Everything AOK. 3 weeks ago my Lenovo 3000H shut down and rebooted for no reason. Then I began getting popups while I was on the internet saying that I needed to click on a button to make a dial-up connection. I would hit X or Cancel to make it go away. It happend more frequently and other related popups started, but I could close them and continue normally. Last weekend It happened again but I lost my connection to the internet and it would not reconnect. Now I get a big error message "Connecting through Wan Miniport(PPPOE)... Error 815: The broadband netowrk connection could not be established on your computer because the remote server is not responding. This could be caused by and invalid value for the "Service Name" field for this connection. Please contact your ISP and inquire about the correct value for this field and update it in the Connection Properties..
    I called Comcast. They don't have a clue what Error 815 is. I have changed every cable, rebooted the modem, router and all computers countless times, and reset the modem per Comcast. I have taken the router out and connected directly into the Lenovo. I have gone through every screen related to broadband connection to no avail although, being a beginner, I see screens that I have no clue what they do.I have a couple of friends and a Comcast fellow who tried to walk me through the steps they thought would restore my connectio. No luck.
    Can anyone walk me through the necessary steps to get me back to ground zero and then through the steps to reestablish my broadband connection?
    Help Please?

    Emma-
    In Safari, press on the Bookmarks icon and select History.  Then press on Clear History at the top of that menu, and see it there is any improvement.
    If not, try unplugging your WiFi router for a few seconds.  Then reset the iPad's network.  Go to Settings-General-Reset-Reset Network Settings.  You will need to reconnect the iPad to WiFi.
    Fred

  • Mozillla will no longer connect to the internet. Chrome and IE connect fine.

    Everytime I open Mozilla it says I can't connect to the internet, but other browsers load it fine. I like Mozilla, but if this is going to be an ongoing issue, I'd rather not use it anymore.

    Did this [[Cannot connect after upgrading Firefox|start after upgrading firefox?]]
    Generally if Firefox can't connect, but other applications can, it's a configuration problem with a [[Firewalls|software firewall]], either one you installed yourself, one that was included with other security software, or the built-in Windows Firewall.

  • TS1398 unalbe to get ipad to connect to the internet after ios upgrade

    helppppppppppp
    i had my it guy from work upgrade me to ios 7 i believe but since then ive not been able to get my ipad to conect to the itunes store or even connect to the internet
    now my it guy says tht it is beyond his skill level and i should take it into the apple store
    can anyone give me any hints
    desperate tim

    Try the following:
    1. Turn router off for 30 seconds and on again
    2. Settings>General>Reset>Reset Network Settings
    3. Reset iPad; hold the Sleep and Home button down until you see the Apple Logo

  • My ipad will no longer connect to the tv after software upate

    until recently my ipad connected to tv with adaptor no problem,since update it says not compatable with ipad

    Hi, sandy5858.  
    Thank you for visiting Apple Support Communities.  
    If the adapter that you are using is an Apple branded adapter, here are some troubleshooting steps that may help.    
    Troubleshooting
    If you encounter an issue using the Apple Digital AV Adapter or VGA Adapter:
    Disconnect and reconnect the adapter from the iOS device and display.
    Connect directly to the TV, projector, or external display using a known-good VGA or HDMI cable.
    Remove any VGA or HDMI extension cables or converters.
    Note that accessories that convert a VGA or HDMI signal to other video formats (DVI, Composite, Component) are not supported.
    Ensure that you are using the latest version of iOS. Some Apple Digital AV Adapters require iOS 5.1 or later.
    Note: When using an Apple Digital AV Adapter manufactured before early 2012 with iPad (3rd generation), you may see the "This accessory is not supported" alert. Dismissing the alert will allow you to use the adapter.
    For optimal performance, you may need to adjust the video resolution or settings for your display. If your display offers an "auto detect" or "factory default" setting, you may be able to use these options to optimize video resolution and display.
    iOS: About Apple Digital AV Adapters
    http://support.apple.com/kb/ht4108
    Cheers, 
    Jason H.  

  • I just updated my iPad to the iOS 6. My iPad will no longer connect to the Internet.

    Help! My wifi says its connecting and then immediately goes off.

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
     Cheers, Tom

  • My iPad (original) no longer connects to the internet after update to ios 5.  Are there any solutions to this issue?

    Has anyone found a successful method to connect?  This is not a router issue as other devices, including another iPad not updated to ios 5 connects just fine.  I am getting frustrated

    I had this problem.  I held down the power switch to power down completely.  Takes a few seconds.  Then use the power switch to turn on.  Might take a couple goes.
    Kirk

  • Downloaded Firefox 8 and it will no longer connect to the internet, is there a fix?

    That's it. downloaded 8 and it won't connect.

    Usually caused because your firewall is doing its job and does not recognize the new version of Firefox
    *See --> [https://support.mozilla.com/en-US/kb/Cannot%20connect%20after%20upgrading%20Firefox Cannot connect after upgrading Firefox]
    '''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''

Maybe you are looking for

  • How to resolve the problem in jdeveloper903 oc4j starting:JspTagLib listener error

    I just download a jdeveloper903,i hava a problem: when i start the oc4j alone,it prompt "JspTagLib listener error:null". Then,After depoly the jsp application with JspTag to oc4j,I found the jsp page can not run,but,the jsp application can run in the

  • Service entry made in TC-ML81N

    Hi There is a  document entered to a G/L-85040(LIABILITY FOR PRIMARY FREIGHT) as a credit entry.While verifying the document it is found that it is a service entry made for AMC in TC-ML81N.More over it is a system entry.Then i verified the TC-OBYC &

  • How to clear cache POP-UP LOV

    Hi All, How to clear cache POP-UP LOV . For example : I had created one pop-up lov "Marketing client", when I select any value from pop-up lov . If the Marketing Client already has 'AIM Investments' but someone clicks the item to get to search for a

  • Need help please with ipod mini

    Hi,I had my ipod mini sent into service as the pasue button was bust and I now have a totally new ipod mini send out and Im trying to install it on the pC and it doesnt let me,need help pls

  • Upgrading Aspire E380 from Vista 32 bit to Windows 7 Pro 64 bit - No device drivers were found

    I'm trying upgrade my Acer Aspire E380 from Vista 32 bit to Windows 7 Professional 64 bit and getting an error that no device drivers were found. This happens after booting from the Windows 7 DVD.  The Acer support site only provides Vista 32 bit dri