My IPad 4th Gen speaker has turned to static. I did a reset, checked the sound and accessibility settings. Any other ideas?
My IPad 4th gen now has static on sound. I've done reset and checked sound controls and accessibility. Help?
A hard reset has been known to remedy this problem.
You might want to detail when the static happens. All the time? Only when you insert the mini jack? With specific software or volume?
Similar Messages
-
My ipad mini 2 is not turning on. I tried to reset with the power/home buttons but it didnt work. I tried to restore it in DFU mode but it didnt work, i get error 4004. Please help me!
I also tried the ol' whacking 3 times trick...Didn't work to my surprise
-
i was texting and locked my phone and now it wont turn back on and i tried charching it and everything.. any other ideas?
Try reseting. You may lose everything on phone though
To reset
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears.
'Home Button' is the Black depression in the Iphone that you can press
'Sleep/Wake Button' is the black raised area at the top of the Iphone -
My iPod Touch 4th gen is disabled for 22,000,000 minutes. I have looked all around the Apple support communities and I always find the same "solution", which is to put it into DFU or recovery mode and restore from a backup. Here's my problem: My computer crashed awhile back and I had to completely start over from scratch. So, unfortunately, a backup of my device no longer exists on this computer or any other computer.
Is there any way I can simply get rid of the disable? I remember my passcode, so that isn't a problem, all I need is to be able to input my passcode.
Or, do I absolutely have to restore to factory settings, and lose all my data?
By the way, I hope it does not matter, but I can't remember the IOS is was last updated with.
Thanks.Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
Need a help to get rid of this error sim card is working randomly
Is there an error message appearing when this happens? Are you in the same area or different areas when this happens?
In the meantime, I would try to take the SIM card out and then put it back in. -
I have a fourth gen iPad that's a few weeks old. It is stuck in whichever orientation I unlock it in, and will not rotate on the fly.
I've tried restarting multiple times. I've tried toggling the side-switch to screenlock or mute, on/off, with no success. Tried closing all programs. Tried locking via software and unlocking...
Still no luck. Any suggestions?
Thanks,
MSounds like a hardware failure. Make an appointment at the genius bar of your local Apple Store. There is no magic that can fix a hardware failure.
-
i have my account set, but i cant find out how to get the apps to properly download. am i doing something wrong?
10.6.8 (Snow Leopard) is an upgrade from Leopard, which you apparently have (10.5.8).
iTunes 11 requires 10.6.8 (not 10.8.6 as you have typed). If your Mac is an Intel one with at least 1Gb of RAM then you can buy Snow Leopard in the online Apple Store (type 'Snow Leopard' in the search box rather than browsing for it).
Once installed, download the combo updater to bring it up to 10.6.8:
http://support.apple.com/kb/DL1399
You will then be able to install iTunes 11. However if your Mac has a PPC processor you cannot install Snow Leopard and will be unable to proceed. To check this, choose 'About This Mac' from the Apple menu and look where it says 'Processor' - it needs to say 'Intel' for you to be able to upgrade. -
What is wrong with my iPad (4th Gen) screen?
Hi all,
My iPad 4th gen screen has stopped working.
It just shows a white fuzzy screen with a thick grey bar across the screen. I have done some percussive therapy (hitting the back) and the thick bar changed colour but other than that nothing happens. I have tried a restore as well but still no luck!
I have trawled through google and some of the ofrums here but i cant find anything about this. Does anyone have any ideas? It has just ran out of warranty as well.
ZackTry this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased. http://support.apple.com/kb/ht1430http://support.apple.com/kb/ht1430
Not normal. Take it to an Apple Store for evaluation.
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/http://www.apple.com/retail/geniusbar/
Cheers, Tom -
I am not able to open or view PDF files on my ipad 4th gen.
I am not able to open or view PDF files on my ipad 4th gen.
Hello,
This looks this issue is specific to this particular banking site and we definitely want to know more to help resolve this issue. It is likely that this particular functionality is not supported on Firefox and I would suggest that you report this to the bank and request them to support it soon.
That said, there are a few things you can do from the details provided in the [[Websites don't load - troubleshoot and fix error messages]] SUMO article. Specifically, the section about [[Websites look wrong or appear differently than they should]] and reporting the website might help us provide more information.
If this is a banking site used by any of the other volunteers who are willing to dig more to find out why, they will try to provide the resolution sooner.
I know this is not really a resolution that will help you, but given that I don't have much information as to what is the offending part of the website causing the issue, I can only suggest this much.
Thank you -
I Am not getting any sound at all from my ipad. I have checked the control panel and it says the sound is "on". Any other suggestions? It has worked just fine in the past.
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) http://support.apple.com/kb/ht1430
Check your settings. The iPads have a small switch on the right edge. http://support.apple.com/kb/ht1430 It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
iPhone: Can’t hear through the receiver or speakers
http://support.apple.com/kb/ts1630
http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
To solve some sound problems, just follow these simple steps
1. Go to Settings
2. Tap on General
3. Tap on Reset
4. Tap on Reset All Settings
What this effectively does is to reset some of your Settings to factory default. It’s not a complete removal of settings. It removes all of your preferences for Wi-Fi, Bluetooth, Do No Disturb, Notifications, General, Sounds, Brightness & Wallpaper and Privacy. It doesn’t affect your data. All of your email accounts will remain intact, as well as any SMS text or iMessages.
Cheers, Tom -
IPad 4th Gen will not access gmail/error message regarding password
iPad 4th Gen,32GB, iOS8.1 suddenly giving error message of incorrect user name or password when trying push emails. Steps tried so far:
unlocked gmail account via Safari browser
changed from fetch to push and back
checked stmp info and turned on SSL
rebooted iPad
deleted gmail account
attempted to load gmail account
Any other fixes to try? Problem just suddenly happened this afternoon. Been working just fine, even after downloading iOS 8.1 over 24 hours ago. Problem has only existed for about 6 hours. Had exact problem with iPhone 6, 64GB, iOS 8.1 at the same time but unlocking gmail account via Safari resolved the problem on the iPhone 6. All other apps on both devices working perfectly.iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Setting Up An eMail Account
http://support.apple.com/kb/ht4810
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
Cheers, Tom -
IPad (4th gen) image burn in/image retention
Has anyone had this issue with image retention or "burn in" on their new 4th gen iPad (lighting connector). I've attached an image taken with my iPhone 4 where I went from messages to "Letterpress" (a word game) where you can still see messages on the grey screen. I turned the iPad off and back on with the same retention being shown on screen. I've only had this thing for two weeks but it seems absolutely ridiculous that this is a problem. Any help or advice would be much appreciated.
Update:
Took my iPad to my local Apple Store. They said it was image retention and said they hadn't seen this on any devices before. They replaced it for another new one with no fuss or bother. I have checked the replacement and at the moment it seems ok.
One thing I have not done yet is to update the software to iOS 6.0.1 I think I will leave iOS 6 (which was on the iPad from new) for the moment to see if all stays ok. After a few days I will update to iOS 6.0.1 just to see if this is what causes the image retention problem. Hopefully this will not make any difference and all will be fine. Watch this space. . . -
Ipad 4th Gen not working at all
Hi
I have an iPad 4th Generation WI-FI and I got it less than 2 years ago and now it doesn't work at all. I will explain a bit more about what happened to it in more detail below. So I was taking photos with it and after I was done I turned it off or as Apple call it "sleep", well I pressed the power button in other words like everyone does, right? Then in the evening I went to go on it and it was blank and wouldn't respond but in the morning it had about 30% battery but anyway it put it on charge using the Apple adaptor and I let it charge for like 30min but when it was charging it kept on showing the Apple logo every 20 seconds but wouldn't go past it. So when I took it off charge I tried holding the Power and Home buttons at the same time for about 20 sec and after about 3 to 4 tries it showed the restore iPad sign with the Lightning cable and the iTunes logo on top of it, so I plugged it into my computer and iTunes poped up and said something like:
iPad 4th Gen detected the device needs to be restored. (By the way my laptop is Win7 and had the latest iTunes on it) So I clicked the restore button and it said EXTRACTING SOFTWARE and after that the line stopped moving and a window came up saying: Unkown Error 4005 and 4013 and it took me to the Apple website and I did all the steps they told me to do and it didn't work and kept on saying the error thing. So I took it to an Apple store and the guy there said he waz restoring it and downloading new software for it and it ended up not workin for him either, but he told me there is nothing to do cause the 1 year warranty expired. Anyway now it doesn't show anything at all not even the restore logo, the apple logo nothing it completely blank and Ive had it on charge for like 2 hours. And I haven't dropped it or anything it doesn't have any physical damage or that. So yeah what should I do? Any suggestions will be appreciatedHi Try this Connect USB lead to pc hold down power button on iPad connect Lead To iPad still hold button down Wait to see if pc sees iPad keep button down for upto 1 Minute. If that doesn't work make An Appointment at Apple Store. Cheers Brian
-
Want to use my iPad (4th gen) to edit a movie using iMovie - easy enough if the movie file is on the iPad - but what if it's too large - can I keep the source file on a USB stick or external USB hard drive and edit from there? How can you do this?
You can't export any type of file using the camera connection kit, so a USB flash drive or SD card won't work.
There are some wireless external hard drives that can be used with the iPad.
The Kingston Wi-Drive, which costs $50 for the 16 Gigabyte, and then $30 more for every 16 gigs more. It works by you turning it on and then accessing the files on it from an app that you download on your iDevice. You can access music, movies, and other stuff. No connections or anything, it works like a WiFi connection, you connect to it from the setting on the iPad under wireless networks.
Then there is the Seagate GoFlex, which some would recommend over the Wi-Drive. But this one costs $199 and had 500 Gigabytes of storage. It works the sameway as the Kingston: no wires, runs over its wireless connection. You can actually fit up to 300 HD movies on it.
Another option:
Expand your iPad's storage capacity with HyperDrive
http://www.macworld.com/article/1153935/hyperdrive.html
On the road with a camera, an iPad, and a Hyperdrive
http://www.macworld.com/article/1160231/ipadhyperdrive.html
Cheers, Tom -
Hi,
I have a problem with Laserjet 100 color MFP M175nw and Airprinting.
Ipad(4th gen) cannot connect to printer for AirPrinting.
Wireless Direct is set on in the printer.
When I choose to connect to printers own wifi network with my Ipad, it can't connect.
(Ipad doesn't show the wifi symbol on top left corner.)
And if I try to print with Safari, it says "AirPrint-tulostimia ei löytynyt" which means in english "No Airprint-printers found".
I have all installations by the guide book several times, but seems that this Airprint simple doesn't work.
Device Configuration show this:
Installed Personalities and Options
PCL6 (20040201)
AirPrint
PCL (20040201)
PDF (20040201)
PS (20040201)
I wonder why AirPrint has empty value? (what ever this might mean)
Br,
HeikkiHi,
Thank you for your reply and first action plan to find a quick fix.
Unfortunatelly even though I disabled IPv6, it didn't fix the problem. Also reboot and WIFI restart has been tryed sevelar times without any help. Ipad Safari is still giving me a message "no airprint printer found".
Same problem also when I try to print so that both Ipad and printer are connected to my home WLAN/DSL-router.
I don't see any problems for the printer to connect my home WLAN, both printer and Ipad has received an IP address from the WLAN router.
My router model is Zyxel AMG1202-T10B.
Ipad is updated to it's latest SW version which is 7.0.6. and printer's firmware date is 20131028.
I have no problems printing with my Windows 7 desktop computer which is connected to same network as well.
Windows 7 PC is connected to router via Ethernet. Printer is connected to router via Wireless, not ethernet.
Here is the network settings from HP Device Toolbox:
Network Summary
TCP/IP(v4)
Status (Wireless) Ready
IPv4 Address: 192.168.1.38
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
IP Configured By: DHCP DHCP/BOOTP Server: 192.168.1.1
DHCP Expiration Time: 02:23:54 (Days:Hours:Minutes)
WINS Server: 192.168.1.1
Preferred DNS Address: 192.168.1.1
Alternate DNS Address: 0.0.0.0
TCP/IP(v6)
Status: Disabled
Network Identification
Host Name: NPI08C7AB
Domain Name (IPv4/IPv6):
Domain Name (IPv6 only):
Bonjour Service Name: HP LaserJet 100 colorMFP M175nw (08C7AB)
Bonjour Domain Name: NPI08C7AB.local.
Bonjour Highest Priority Service: IPP Printing
Wired Network Configuration
Status: Not Connected
Hardware Address: 2c:44:fd:08:c7:ab
Link Speed and Duplex Negotiation: Automatic
Auto Crossover: Enabled
Wireless Network Configuration
Status: Connected Wireless: On
Network Name (SSID): Galactica
Communication Mode: Infrastructure
Authentication Type: wpa-psk Encryption: tkip+aes
Hardware Address: bc:85:56:ee:02:d3
Access Point Hardware Address: 28:28:5d:7c:23:a0
Channel: 10
Signal Strength: Excellent
Wireless Direct Setup
Status Enabled
Wireless Direct Printing Name (SSID) HP-Print-d3-LaserJet 100 Wireless
Direct Printing Channel 10
IP Address 192.168.223.1
SNMP
Status: Read-Write Access Enabled
SNMP Version: 1
Set Community Name: Not Specified (Defaults to 'public')
Get Community Name: Not Specified (Defaults to 'public')
Network Statistics
Total Packets Received: 428
Unicast Packets Received: 414
Bad Packets Received: 0
Framing Errors Received: 0
Total Packets Transmitted: 493
Unsendable Packets: 10
Transmit Collisions: 0
Transmit Late Collisions: 0
WS-Print Users: 0
Enabled Features
IPv4: Enabled
IPv6: Disabled
DHCPv6: Enabled
LPD Printing: Enabled
Bonjour: Enabled
SLP: Enabled
WS-Discovery: Enabled
SNMP: Enabled
Show IP Address: Enabled
LLMNR: Enabled
Security PJL Security: Disabled
Please let me know if you need any other additional information.
Br,
Heikki
Maybe you are looking for
-
AD security group memberships not coming over to SP2013.
This seems to have coincided with applying a number of updates to our SharePoint server via Windows Update over the weekend. Since then, changes in AD security groups are not being reflected by the appropriate access in SharePoint. If somebody has
-
Button issues on Question slide
Hi there I have a simple quiz in my project which the users can skip if they want to. I want the users can go Back from the question slide. The back button works for the first time taking to the previous slide(not a question slide). But when i again
-
Using Warehouse Builder v10gR1 (repository is 10.1.0.1.0) on a 10.1 Db AFAIK, no changes to this mapping or objects related to mapping, but it has been hanging every execution since Saturday, whether it's run as part of a workflow or on its own. The
-
How do you connect Text Boxes? So that text flows from one to the other, on same page or following pages?
-
How can I get my new iMac to see my old Airport Express so I can play my music to a remote speaker?