My iPad is glitching it goes from the Internet to the home screen with no warning I have completed a restore to factory settings still doing it. Please help

Setup as new (Factory Default)
Settings>General>Reset>Erase all content and settings
Note: if iPad still crash after setting up as new, it's time to make appointment with Apple.

Similar Messages

TS3219 When on iTunes on my first generation iPad it defaults back to the home screen with no warning

When trying to view the film category in iTunes my iPad defaults back to the home screen so I can't buy a film or even view products. Why is this happening ? Is there anything I can do?? My iPad is using iOS 5 and it is upto date as it is a first generation iPad. Please help!!!
Thanks

This is most often the result of iOS closing apps when it experiences a low-memory situation. The original iPad has very limited RAM by todays standards for Apps. If you have apps open, be sure to close them to preserve your RAM for apps you actually want running.
To do so, double-tap the home button, then press and hold an app icon until they start to shake. You can close apps in the multi-tasking tab by tapping the little circle that appears.Be sure you don't do this on the main home screens because tapping the X will delete apps from your device rather than close them.

When i try to go out of a text conversation and go to all of my texts it glitches and goes to the home screen. I've tried everything, and I just got this phone yesterday please help.

I was thinking maybe iOS 7 on wednesday would fix it but I'm not sure?

Have you restarted your device?
Have you reset your device?
Have you done ANY troubleshooting on your own yet?
Basic Troubleshooting Steps when all else fails (or you haven't tried a dang thing yet)
Quit the App by opening multi-tasking bar, holding down the icon for the App for about 3-5 seconds, and then tap the red circle with the white minus sign.
Relaunch the App and try again.
Restart the device. http://support.apple.com/kb/ht1430
Reset the device. (Same article as above.)
Restore from backup. http://support.apple.com/kb/ht1766 (If you don't have a backup, make one now, then skip to the next step.)
Restore as new device. http://support.apple.com/kb/HT4137 For this step, do not re-download ANYTHING, and do not sign into your Apple ID.
Test the issue after each step. If the last one does not resolve the issue, it is likely a hardware problem.

Everytime i click on my ipad contact app it goes to the main screen

Hi,
Everytime iclick on my contact app it goes back to my screen help please
Cheers
Paulbrookes4

Try toggling Settings > iCould > Contacts off and on and see if it then works.
If it doesn't then try closing Settings completely and then re-open it : from the home screen (i.e. not with Settings 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Settings app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
A third option is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Will the iPad Mini print to / scan from the HP 7280; with USB cable?

Will the iPad Mini print to / scan from the HP 7280; with USB CABLE?
Thanks, everyone...
---sue h (Apple novice)
iPad Mini

https://itunes.apple.com/us/app/genius-scan-pdf-scanner/id377672876?mt=8
I use this app. It takes a photo and turns it into a PDF (the photo that you take with your iPad/iPod)

Since yesterday my Apple TV will not load the movies or tv at all. I select it from the home screen, it goes black, tries to load then goes back to the home screen. YouTube and Netflix works though. I've reset the Apple TV and the modem. No change. help?

Since yesterday my Apple TV will not load the movies or tv at all. I select it from the home screen, it goes black, tries to load then goes back to the home screen. YouTube and Netflix works though. I've reset the Apple TV and the modem. No change. Any ideas what the problem is?

Apple TV: Unable to access Movies, TV Shows, or other iTunes features after updating
http://support.apple.com/kb/TS4526

When I unplug my headphones from my iPod touch 4G, it goes from the apple screen to the lock screen and i can't do anything with it. It's only about a year old..why is it doing this?

When I unplug my headphones from my iPod touch 4G, it goes from the apple screen to the lock screen and i can't do anything with it. It's only about a year old..why is it doing this?

Have you tried restoring to Factory Default (setup as new).

How do I remove a shortcut from the Home Screen of...

How do I remove a shortcut from the Home Screen of a Nokia 700? I'm a bit clumpsy with the touch screen and I keep adding shortcuts for everyrhing. It's easy enough (too easy) to add them, but how can I remove/delete them? There doesn't seem to be any option to deleting them and it's not mentioned in the manual.
Solved!
Go to Solution.

jimmyireland wrote:
You tap the icon hold for a second or two the x icon appears then you tap it then it goes
Now I got it. Thanks for the help.
I really need to practice this touch screen malarky, I'm not very good at it.

My 5th generation iPod (bought in April of 2013) will quit unexpectedly. It will take for ever to load what I write while texting. It also just goes to the black screen with the Apple logo. I'm not sure what to do.

My 5th generation iPod (bought in April of 2013) will quit unexpectedly. I can't do app store apps (like snapchat or facebook, ect.) or apple apps (like Camera, Safari, ect.)It will take for ever to load what I write while texting. It also just goes to the black screen with the Apple logo. I'm not sure what to do.

Try This...
Close All Open Apps... Sign Out of your Account... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
If no joy...
Reset all settings
Settings > General > Reset > Reset all Settings.
This will return all iDevice settings to factory defaults... you will not lose any data.... But you will have to re-enter all of the device settings.
If the issue persists...
Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414
Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
More Tips here...
http://osxdaily.com/2013/09/23/ios-7-slow-speed-it-up/
http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/
Note:
Also consider Deleting any Apps you have Purchased / Downloaded but you now never use.

Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that.

Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

I did a factory reset on my ipod touch, but now when i try turning it on it just goes to the apple screen with the loading sign

i did a factory reset on my ipod touch but now when i try turning it on it just goes to the apple screen with a loading sign, ive let my battery die and tried reconnecting but it still wont work. it doesnt even come up on itunes.

Why won't it let you sync? What happens when you try to sync it? Any error messages from iTunes? How is your iPod configured to sync music from your iTunes library? In other words, what options do you have selected from under the iPod's Music tab in iTunes? To access this tab, plug your iPod in, select it under Devices in the left hand pane of iTunes, and over to the right locate and select the Music tab along the top.
Or are you trying to manually manage your iPod's contents? In other words, is the Manually manage music and videos option enabled from under the iPod's Summary tab?
B-rock

Is there anyone having an issue with the apple tv when selecting music from the home screen?

Is there anyone in the community having an issue playing music from the home screen of the apple tv? When selecting the music app my apple tv restarts. If anyone else is having the same issue and has corrected the problem please share the solution.

Working fine here, and have not seen any other reports. I would restore your unit
Apple TV (2nd and 3rd generation): Restoring your Apple TV - Apple Support

I have a Mac, IPad, I phones, and 2 Windows Vista Pcs and I'm having trouble with the Windows Laptop staying connected. I have to re-boot after and extended period of time please help

I have a Mac, IPad, I phones, and 2 Windows Vista Pcs and I'm having trouble with the Windows Laptop staying connected. I have to re-boot after an extended period of time please help. Thanks!

I have a Mac, IPad, I phones, and 2 Windows Vista Pcs and I'm having trouble with the Windows Laptop staying connected. I have to re-boot after an extended period of time please help. Thanks!

I am using iphone 4..32 gb...i hav updated to ios6..i am experiencing serious lags...watever m doin d phone lags n goes to the home screen...frequency is much greater..please help me with it...i even replaced my device but same problem on new one..!!!!

please help me with dis...
I am using iphone 4..32 gb...i hav updated to ios6..i am experiencing serious lags...watever m doin d phone lags n goes to the home screen...frequency is much greater..please help me with it...i even replaced my device but same problem on new one..!!!!

Restore the phone as a new device. There is probably something that was corrupted on your phone during the update and has been passed via the backup to the replacement phone. If the corruption/problem is contained in the backup, you'll need to re-sync your data, and re-install your apps manually. Restoring the backup again will only bring the problem back with it.
If restoring it as new does not fix it, then make an appointment at the genius bar.

In the middle of a movie, the movie stops and it goes to the home screen. We can't watch it again, how do we fix it?

In the middle of a movie, the movie stops and it goes to the home screen. We can't watch it again, it basically just takes our money away, how do we fix it?

Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Reset the Apple TV (Settings > General > Reset > Reset all settings)
Restore the Apple TV (Settings > General > Reset > Restore)

My iPad is glitching it goes from the Internet to the home screen with no warning I have completed a restore to factory settings still doing it. Please help

Similar Messages

Maybe you are looking for