My ipad is missing can i track with just serial no
my ipad mini is missing can i track with just serial no, my serial no is F4*******CM6
<Edited By Host>
You can only track the iPad if Find My iPhone was enabled. You can log in to icloud.com with your Apple ID and see if it appears on the map.
~Lyssa
Similar Messages
-
What does this message mean? "itunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with ITnes." How do I restore when every time I connect to my computer I get this message?
Perhaps the information in this Apple support article will help:
http://support.apple.com/kb/TS3694#error3004
Regards. -
I have windows 8 enterprise OS and iTunes ver. 10.5.0.142. I was upgrading my iPad to IOS 6.1.3. After finishing the upgrade my iPad Reboot and currently stucked-up in a plug-in screen and iTunes Logo. When I try to connect it to the iTunes pop-up message appear saying " iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes." In short, I push the restore button then another pop-up message appear saying " The iPad software update server could not be contacted. Make sure your network settings are correct and your network connection is active, or try again later." I tried many ways but still no luck. I repeatedly reboot the iPad and open the iTunes still the same problem. I try also to uninstall the iTunes and installed the lower version but still the same problem, I even check the firewall if the ITunes was block or My privileges is administrator to run the iTunes or even reset my winsock but the problem still remain. PLEASE HELP! Thank you in advance!!!
Turn off your firewall and antivirus software.
-
Went on a Vegas trip on Sept
11th. My iPad worked fine
before getting on the plane. In the hotel about 48hrs later I opened my iPad it
read the message: “iPad is disabled,
connect to iTunes.”
To my knowledge myself, nor anyone else has tried to access my device or
entered the password incorrectly 3 or more times.
I started by updating my iTunes account on my computer to the latest version.
Then multiple times I attempted
the “Use recovery mode”
steps.
e.g.
1. Turn off your device and leave it off.
2. Plug in your device's USB cable to a computer with iTunes.
3. Hold down the Home button on your device as you connect the USB
cable. Keep holding down the Home button until you see the Connect to iTunes
screen.
I received the message on my computer saying “iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes.”
I click the “Restore iPad” button.
During which time the progress bar on my computer’s iTunes
screen was moving very slowly and other times seemed like it wasn’t moving at
all. I would leave my two devices and attached by the cable and upon returning
I would find that the process would have ended before it had completed.
Initially I thought it was a connections issue because I was in remote
locations with slow internet servers. Since being home I have re-attempted the
process and have been able to fully complete the forced recovery but I will
receive a message saying:
“The iPad could not be restored. The disk you are attempting to use is full.
Removing files and emptying the recycle bin will free up additional space.”
What recycle bin is the message referring to? Obviously I CANNOT access any
data on the iPad itself. Just for the **** of it, I did empty my computers
recycle bin and re-attempted the forced recovery process but as I suspected it
did nothing for the iPad and I still received the same message: “The iPad
could not be restored. The disk you are attempting to …”
Please helpHere's a couple of Apple Support articles ...
Resolve iOS update and restore errors
If you can't update or restore your iPhone, iPad, or iPod touch -
my ipad is disabled and it said ipad is disabled connect to itunes but i connected it and was restoreing it and then there was a popup and it said itunes cannot connect to ipad because it is locked with a passcode. and you must enter the passcode on the ipad before it can be used with itunes. But i couldnt even write the passcode on my ipad cause it was disabled. What should i do now????
Follow the instructions on this page to reset your iPad : http://support.apple.com/kb/HT1212
Note: If iTunes asks you to enter the passcode, try another computer that you have synced with. Otherwise, go to "If you have never synced your device with iTunes, or you do not have access to a computer" section below.
If you have never synced your device with iTunes, or you do not have access to a computer
If you see one of following alerts, you need to erase the device:
"iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."
"You haven't chosen to have [device] trust this computer"
If you have Find My iPhone enabled, you can use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
Alternatively, place the device in recovery mode and restore it to erase the device:
Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
Continue holding the Home button until you see the Connect to iTunes screen.
iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device. -
I try to update IOS 6 to my ipad 2/ wf/3g and after about half of the procedure stopped ... then I try to reconnected to the itunes and say "iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes". Can everyone help please. In the screen of iPad appears the itunes Logo and the cable of connectios. Can't do nothing!!!
Click restore in itunes.
-
Error message on ipad when we tried to download images to computer. 'Itunes has detected an ipad in recovery mode. You must restore your ipad before it can be used with iTunes. It downloaded some images prior to this message and we selected skip any files with errors.
Ipad now just showing apple image with power cord. Don't want to click restore and lose all data.Once the Device is asking to be Restored with iTunes... it is too late to save anything...
To minimise loss... Connect to iTunes on the computer you Usually Sync with and Restore from the most recent Backup...
http://support.apple.com/kb/HT1414
Restore from Backup
http://support.apple.com/kb/ht1766 -
I try to connect to iTunes and it comes up with a box saying "iTunes could not connect to the iPad because it is locked with a passcode. you must enter your code on the iPad before it can be used with iTunes", but i cant enter the code on the iPad because it is saying "connect to iTunes". Can anybody help?? It is on the new iPad.
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY. -
itunes could not be connected to ipad because it is locked with a passcode, i must enter a passcode on the ipad before it can be used with itunes but all i see is "iPad is disabled connect to itunes" I have a passcode but nothing shows on the screen
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
i cant reset my i pad it wont let me
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY. -
I downloaded the update because why not. I then turned my iPad on and get the iTunes logo and a lightning cable picture. I plugged the ipad into my computer and opened iTunes.
The I got:
"iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes"
When I click restore it then says:
"Are you sure you want to restore the iPad "iPad" to its factory settings? All your media and other data will be erased, and the newest version of the iPad software will be installed.
iTunes will verify the resotre with Apple. After this process is complete, you will have the option to restore your contacts, calendars, messages and other settings."
I don't want to lose my media. I was never told to make a back up, I was never told the update would be this difficult.
Can I just revert back to how it was before?I downloaded the update because why not. I then turned my iPad on and get the iTunes logo and a lightning cable picture. I plugged the ipad into my computer and opened iTunes.
Then I got:
"iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes"
When I click restore it then says:
"Are you sure you want to restore the iPad "iPad" to its factory settings? All your media and other data will be erased, and the newest version of the iPad software will be installed.
iTunes will verify the resore with Apple. After this process is complete, you will have the option to restore your contacts, calendars, messages and other settings."
I thought okay, I'll just erase everything then. I get error 3004 when I try to restore.
I've tried disabling my security software, updating iTunes, replacing my hosts file and using a third party software recovery tool. Nothing works. I never thought Apple would break my iPad with an update but they managed to.
Any solutions?
Thank you. -
in attempting to reset my ipad2 thru itunes it states .iTunes has detected an iPad in recovery mode. You must restore this iPad before it can be used with iTunes. when i hit restore it does not reset
Step by step
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. iPad Recovery Mode on computer screen
8. Select "Restore iPad"...
9. Select "Restore and Update"
10. Extracting Software.
11. Preparing iPad for restore.
12. Waiting for iPad.
13. Verifying iPad restore...
14.Restoring iPad software.
15. Verifying iPad software.
16. Verifying iPad Restore...
17. Restoring iPad firmware...
18. Your iPad is restored to factory settings; keep iPad connected to computer
19. Activate iPad
20. Enter Apple ID and Password
21. Continue
22. Welcome to Your New iPad -
How do I create a track with just controller MIDI data in it?
How can I create a track with just MIDI controller data in it?
For example: I'd like to create a track that issues a bank change/patch change and sets the default volume for that track, and that's it.
I can then use this setup as a template for future projects.
How can I do this?
It seems like LPX will not allow me to enter any controller data into a track without first defining a region. However, it seems that LPX also won't allow me to create a region with just controller data in it.
Ideas?
Thanks
-MikeSoniq2 wrote:
How can I create a track with just MIDI controller data in it?
For example: I'd like to create a track that issues a bank change/patch change and sets the default volume for that track, and that's it.
I can then use this setup as a template for future projects.
How can I do this?
Let me qualify, I'm using Logic 9, not upgrading for various reasons.
Is this for an external Instrument? If so it's very easy to do using the inspector, but first you have to create an instrument in the environment. (at least in L9 and the way I do it, which is old school) Here's an example of an external instrument setup in the Environment.
A multi Instrument is created, channels 1, 2, 3, & 9 are active. Patch names are entered, format for bank change is selected. (just happens I selected channel 14 to open the patch names). This Instrument will now appear in the arrange page, and you can set patch change, bank change, volume & pan. -
I was updating my Ipads software when it just shut off. I turned on the i pad and it gave me this picture of the wire plugging in to itunes. i plugged it into i tunes and i got this message on itunes saying itunes has detected an ipad in recovery mode. you must restore this i pad before it can be used with i tunes. pleasssse help
iOS Recovery Mode -
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808 -
How can I export an audio track with just the effect signal without the audio?
I want to export dry audio tracks and their effects signals as separate tracks. For instance a track with a reverbed snare would be one track with the dry snare and one with just the reverb.
I know from people who use Reason that it's just a box you need to tick, but I'm struggling to find out how to do it in Logic. Surely it must be a way?I don't remember Reason being that straight forward, but the obvious way to go, is to mute all sends and bounce.
Then solo the reverb channel, in aux, checking it isn't shared by other sources, and bounce. You should have a dry and a reverbed signal, at your convenience.
Maybe you are looking for
-
I want my songs back, i have paid for these songs I would like to listen to them on my iPod. It's that simple. I don't want to have to pay someone to fix my iPod over the phone. This has happened to me before and i really get frustrated when i can't.
-
Locking multiple records in a database table at a time
Hi Experts, I have a requirement to lock multiple records in the database table for writing. I have created lock object in SE11. But with this we have only 2 possibilities either lock entire table or lock a single record at a time. My requireme
-
"Copy and Paste"-Event in Indesign
Hi everyone, does anyone have an idea, if there is SOMEWHERE an event, which is fired upon "copy and paste"-ing one or multiple object in Indesign?
-
First, sorry for my English. It is necessary to rename a treenode by selecting of a menuitem from the contextual menu like to rename folder in Windows explorer. Did so: 1.) Last used treenode: (- Tree in MXML) <mx:Tree id="computerTree" width="100%"
-
How do I authorize another PC with Windows 8.1?
How do I authorize anoth PC I Phone 5S with windows 8.1