My iPad (original) no longer connects to the internet after update to ios 5.  Are there any solutions to this issue?

Has anyone found a successful method to connect?  This is not a router issue as other devices, including another iPad not updated to ios 5 connects just fine.  I am getting frustrated

I had this problem.  I held down the power switch to power down completely.  Takes a few seconds.  Then use the power switch to turn on.  Might take a couple goes.
Kirk

Similar Messages

  • My macbook pro (lion 10.7.2) takes several minutes to connect to the internet after waking from sleep.  Is there any way to make this instant?

    Hi
    My Macbook Pro 15 inch takes several minutes to be able to connect to the internet after waking from sleep.  Does anyone else have this problem and is there a fix?
    Alan

    coxorangepippin wrote:
    The message that comes up when I click on "TomTom Home Install" is "You cannot open Home Install because Power PC applications are no longer supported." Does this mean that the TomTom, which is absolutely vital to my life - well, not literally but you know what I mean - can no longer be used with my MacBook Pro?
    What that means is that is can't be used with Lion 10.7.  PowerPC was the chip Apple used up until 2006 when they switched to Intel.  At that point, they created the Rosetta emulator to allow for PPC support for 5 years.  They finally dropped the support with the release of Lion.  It will only work with OS X 10.6 or earlier.  The other option is to purchase a new GPS, which can be had for $100 for a decent one.

  • HT5654 after update to the latest version on my ipad, it no longer connects to the internet nor can i send emails.  when plugged in to sync with itunes, it remains 'stuck' at syncing  step 2 of 7 backing up.  has anyone had similar problems? any solutions

    after update to the latest version on my ipad, it no longer connects to the internet nor can i send emails.  when plugged in to sync with itunes, it remains 'stuck' at syncing  step 2 of 7 backing up.  has anyone had similar problems? any solutions?

    I had this problem.  I held down the power switch to power down completely.  Takes a few seconds.  Then use the power switch to turn on.  Might take a couple goes.
    Kirk

  • My iphone 5 has restored to an old backup after updating to ios 7 is there any way of getting my stuff back as this has now become the most recent back up?

    my iphone 5 has restored to an old backup after updating to ios 7 is there any way of getting my stuff back as this has now become the most recent back up?
    also since the update it keeps resetting itself? i had a lot of stuff on there that i really wanted and alot of important info lost? please help!!

    You might be able to remove the recent backup from the backups folder and the old one should be usable at that point
    USE EXTREAME CAUTION WHEN ACCESS THE FILES AND DO NOT DELETE ANYTHING
    Mac: ~/Library/Application Support/MobileSync/Backup/
    Note: The "~" represents your Home folder. If you don't see Library in your home folder, Option-click the Go menu.
    Windows XP: \Documents and Settings\(username)\Application Data\Apple Computer\MobileSync\Backup\
    Note: To quickly access the Application Data folder, click Start, and choose Run. Type %appdata% and click OK.
    Windows Vista, Windows 7, and Windows 8: \Users\(username)\AppData\Roaming\Apple Computer\MobileSync\Backup\

  • My ipad will no longer connect to the internet. Everything else does.

    My ipad 1 will no longer connect to the internet. Everything else does. and nothing new was done to the ipad. It's running ios 4 and was fine since the day it came out.

    Emma-
    In Safari, press on the Bookmarks icon and select History.  Then press on Clear History at the top of that menu, and see it there is any improvement.
    If not, try unplugging your WiFi router for a few seconds.  Then reset the iPad's network.  Go to Settings-General-Reset-Reset Network Settings.  You will need to reconnect the iPad to WiFi.
    Fred

  • WRT54G ver. 6 can no longer connect to the internet after reset

    I reset my WRT54G ver. 6 to clear the password, and now I can no longer connect to the internet with it. I can see the router itself from my PC, but that is all. I've followed the directions here for connection problems, but I can't seem to get an IP Address for it in the Web Configuration tool. Anybody have any thoughts?

    Since you reset your router, you need to reconfigure it back again. try the online utility that automates the configuration. download Easy Link Connect utility at www.linksys.com/connect then download "Netset" and follow instructions.
    if not Easy Link connect didnt work then you need to do the configuration manually.
    1. check physical connection modem should be connected wired to internet port of the router then PC to numbered ports of the router.
    2. Brighthouse i believe is cable connection, right? try power cycle your devices (turn off modem and router then turn on modem 1st then router next). check if your online.
    3. if not. check PC ip. click "start" then "run" type in "cmd" then press "OK". the command prompt should pop-up. type "ipconfig" and check IP and gateway. you should be getting an ip: 192.168.1.x and gateway: 192.168.1.1
    4. access router. open IE, then type in http://192.168.1.1 on address bar.
    5. you will be prompted with username and PW. "admin" is the default password. on setup, just below are subtabs. select "MAC address clone". in it, set "mac clone" to "enable" then click on "clone" then "save settings".
    6. power cycle devices again. try to go online
    note: if you dont have latest firmware. try updating if needed
    Message Edited by whodas on 11-07-200601:28 PM
    it is EVIL enough for GOOD men do NOTHING.

  • New ipad will no longer connect to the internet.

    This is not a network problem - all my other devices work fine and are connecting (including iphone, MacBook, girlfriends "new" ipad). Mine worked fine for months then suddenly, i get the wifi signal but in settings, you just see the spinning gear - not the check mark. When you try to open a web page, it just says "not connected to the internet"
    This is the second time this has happend with the 3rd generation ipad.  I had an ipad 1 for years and no probs, then i upgraded to the new one and it stopped connecting after a month or two. PC World said they had a few people report the same problem so just gave me a refund. Bought a replacement new ipad at Apple and now the same thing has happened to that one.  I guess i could take it back to apple but surely there is a fix for this?

    I should add that i have also done:
    - reset (holding two buttons)
    - updated software to latest IOS
    - done a full restore to original settings
    None of this has solved the problem.

  • My iPad 2 will no longer connect to the internet after iOS 6 update

    HELP!! My iPad doesny connect tot the internet anymore. I down loaded iOS 6 today (9/19/12) and now it doesnt connect tot the internet anymore.

    Hello dchoffa,
    Thank you for using Apple Support Communities!
    I would start with this troubleshooting from the article named:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    If the above troubleshooting does not resolve the issue, I would next try the troubleshooting in one of the other sections down toward the bottom that fits your scenario.
    Regards,
    Sterling

  • No longer can connect to the internet after updating to 10.4.10 for Intel

    I (fortunately) use a cloning program (SuperDuper) to clone my MacBook Pro hard drive now and then on to an external Firewire hard drive... I say "fortunately" because after reading some of the problems folks were having with this most recent OS X update (10.4.10) I chose to update the cloned hard drive first before installing the update on the main drive... On or about 6/20 an update came out (that I can't find anymore so maybe they pulled it??) that was called "MacOSXUpd10.4.10IntelPatch.pkg". First I installed that update on my cloned drive... It booted and worked fine except that when I would try to communicate with the internet wirelessly, I could not... I didn't try a "wired" connection because I am not interested in connecting that way. The system would claim to connect to my wireless router (NetGear WGU624) but pages would time out before loading... Next I tried installing the newer (7/02) Combo package called "MacOSXUpdCombo10.4.10Intel.pkg" but that improved nothing. Still no useable wireless internet connection... So in no way will I be putting this 10.4.10 update (Patch or Combo) on my main drive until something gets fixed... In fact, I went ahead and overwrote what I had on the firewire drive by recloning my main drive (running under 10.4.9) to that firewire drive again... Once I got 10.4.9 reinstalled on that firewire drive, it again connected to the internet just fine... So my experience is that there is something not happy about either the Patch or the Combo updates for 10.4.10, at least as it relates to my Intel system... I also have a G4 PPC and on that machine, the PPC version of the 10.4.10 update worked just fine (though that is a wired connection, if that matters)... Anything I am missing or can someone offer other input other than not to upgrade at this time??? Thanks... Bob...
    FW800 G4 dual 1.25 Ghz and 17 inch MacBook Pro   Mac OS X (10.4.9)  

    Hello Robert:
    I infer from your post that you selected the updates to install, rather than using software update (IMHO a bad idea). At the moment, as I understand your post, your backup is not working properly and your internal HD has not been changed.
    I suggest this:
    Clone your HD to your external firewire drive (new copy, not an update of changed data.
    Then you have a clone in case someting goes wrong.
    Update your HD using software update. If everything is running well after that, you are OK. If not, you can restore your HD from the clone.
    The reason I favor using software update is that the system selects the proper software. When Apple releases updates, there are several versions available.
    If you know all this, forgive the explanation - I do not know your level of computer expertise.
    As an aside, there is nothing (that I am aware of) organically wrong with the OS X 10.4.10 update. Apple did release a 10.4.10 v1. update for the Intel boxes (I do not run Intel-based Macs, so I have not investigated it):
    http://www.apple.com/support/downloads/macosx10410updatev11intel.html
    Barry

  • TS2634 My friends sd card reader no longer shows the pictures after updating to ios 7, is there a fix?

    My friend has an ipad, and after updating to ios 7.0.2 the sd card reader that came with it no longer shows the pictures... just squares where the pictures would be. Is there a way to fix this?

    @ Settings>iCloud
    1. Icloud account being used
    2. I see the following switches
    >mail
    >contacts
    >reminders
    >safari
    >notes
    >keychain (not a toggle switch)
    >photos (not a toggle switch)
    >find my iPhone
    3. Storage & Backup
    delete account option

  • I have an I Pad 1 with 64 gigs. It constantly drops me off the Internet for no apparent reason. Is there any fix for this problem?

    My I Pad 1 constantly drops me off the Internet and programs. Is there any fix for this problem?  It started after the last update and continues to get worse.
    Doug

    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.

  • My ipad will no longer connect to the tv after software upate

    until recently my ipad connected to tv with adaptor no problem,since update it says not compatable with ipad

    Hi, sandy5858.  
    Thank you for visiting Apple Support Communities.  
    If the adapter that you are using is an Apple branded adapter, here are some troubleshooting steps that may help.    
    Troubleshooting
    If you encounter an issue using the Apple Digital AV Adapter or VGA Adapter:
    Disconnect and reconnect the adapter from the iOS device and display.
    Connect directly to the TV, projector, or external display using a known-good VGA or HDMI cable.
    Remove any VGA or HDMI extension cables or converters.
    Note that accessories that convert a VGA or HDMI signal to other video formats (DVI, Composite, Component) are not supported.
    Ensure that you are using the latest version of iOS. Some Apple Digital AV Adapters require iOS 5.1 or later.
    Note: When using an Apple Digital AV Adapter manufactured before early 2012 with iPad (3rd generation), you may see the "This accessory is not supported" alert. Dismissing the alert will allow you to use the adapter.
    For optimal performance, you may need to adjust the video resolution or settings for your display. If your display offers an "auto detect" or "factory default" setting, you may be able to use these options to optimize video resolution and display.
    iOS: About Apple Digital AV Adapters
    http://support.apple.com/kb/ht4108
    Cheers, 
    Jason H.  

  • I just updated my iPad to the iOS 6. My iPad will no longer connect to the Internet.

    Help! My wifi says its connecting and then immediately goes off.

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
     Cheers, Tom

  • I have an ipad 4 running ios 7 but i noticed ios 7 on my ipad seems laggy. I already did a factory reset but it seems doesn't change a bit. Are there any solution for this or I need to wait for the next ios 7 update?

    Am I the only one who facing this problem or there someone else. I did a factory reset yesterday but it still laggy. Do I need to wait for the next ios 7 update or what?

    Hi Amish,
    I should have mentioned that I have signed out of the iCloud Control Panel several times and no syncing occurs.
    Thanks for your response anyway. I appreciate your feedback.

  • HT4623 This update drinking the battery of my I pad air ,is there any solution for this update

    This 7.0.4 is eating my iPad air battery ,don't know what to do ,before once I was have the old update 7.0.3 the battery was amazing can u plz solve this problem soon !!!

    Reduce battery drain
    http://osxdaily.com/2013/09/19/ios-7-battery-life-fix/

Maybe you are looking for