My ipad will not wake on incoming calls on face time

If I let my ipad go to sleep it will not wake up on incoming calls. My calls other devices are not received.

Try putting it into recovery mode.
Connect iPad to your computer via USB while it's turned on.
Open iTunes
Hold the iPad's Sleep/Wake switch (power button on the top of the iPad) down until the "power off" slider appears.
Power off the iPad completely (wait for the progress spinner to disappear).
Hold the Sleep/Wake switch AND the Home button down for a full 10 seconds.
After 10 seconds (the second time you'll see the Apple logo on the screen) release the Sleep/Wake switch while still holding the Home button.
Continue to hold the Home button for another 10 seconds until the USB connection image appears on the iPad's screen, then release the Home button.
A pop-up message will appear on iTunes saying it has detected an iPad in recovery mode, you must restore...
Click on the "Restore" button and the process will begin.

Similar Messages

  • HT4528 my ringer will not sound with incoming calls, please help

    my iphone 4s will not ring with incoming calls.  any ideas on how i can fix it?

    Try sliding the button that is above the volume up and down buttons to see if you have it muted.

  • Laserjet cm1415 will not stop showing "Incoming Call"

    I have the fax setup in manual mode and it will not stop showing  "Incoming call" on the panel even thjough there is no call comming in. Other than that everything works well. Any body have any ideas on how to get it off of that so the printer can go into sleep mode?
    Thanks

    The "Incoming Call" message is shown whenever we see a ring signal on the line, regardless of the fax receive mode.
    If this message is showing up when no fax is being sent, then it means that there is noise on the phone line.  You can contact your phone company to discuss options in reducing the noise on your phone line.
    If this message is showing up with no phone line plugged in, then the modem inside the printer is detecting noise.  It is possible that the internal fax parameters have become corrupt.  If that is the case, then you can perform a "Restore Defaults"  in order to reset them.  Note: doing this will erase all of your settings.  You can print out a configuration report before doing this so you can reset them.  A restore can be done at the control panel by pressing [Setup] on the main screen (the button with the wrench on it), then select "Service" and then "Restore Defaults."
    This is based on my own experience with the product.
    I am an HP Employee.

  • HT201401 my phone only vibrates and will not ring on incoming calls.  How do I fix this?

    My phone only vibrates and does not ring on incoming calls.  How do I get the audible ring?  John

    on left side of your phone you have volume controll an right above that is a small button an if you see a orange or red dot you are in silent mode flip the switch up an it will remove silent .

  • My new iPhone 5S will not ring for incoming calls.  It vibrates. I've tried suggested tips for iPhone 4 but it doesn't work for 5S.  Please help!!

    Can anyone help.  My new iPhone 5S does not ring for incoming calls.  It vibrates.  How can I get ringer to work?

    Hello lyngos,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/TS2802
    If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
    If the iPhone is paired with a Bluetooth headset or car kit:
    Try turning off Bluetooth.
    If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
    Restart the iPhone.
    If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
    Best of luck,
    Mario

  • Will not ring when income calls

    I have tried with Verizon to get issue of phone will NOT ring when a call comes in.  Have checked settings and all seem correct.  Help

    Call *73 to insure your phone is not forwarded. Is it all calls or a specific number?

  • Volume keys will not work with incoming calls on headphones

    So the headphone that came with my iPhone 4s, and others of the same type I have used, will not allow me to lower the volume of the caller. I would be listening to my music or something, it could even be at 50% volume, however the incoming call pushes it to 100% and will not allow for my headphone or iPhone volume control turn down the call. I have to unplug my headphones and just talk on the phone its self in order to turn down the volume.
    This problem was first noticed in iOS 6, and is contiued into iOS 7. I do not recal it happening in iOS 5.

    TTY was on after going through the settings one by one. They need to explain what TTY is within the settings menu. I have been useing TTY for 2 years now not knowing it.

  • My ipad will not let my friend call from their iphone

    I just got an ipad 2 today and added someone onto my contacts but for some reason it will not let us connect and I don't know why.

    ya I knwo that but if I am wifi connected and they call my email the face time should work and for some reason it is not.

  • My contact names will not display with incoming calls

    I just received the I-phone 4S.  I had the 3GS.  I have synced properly on i-tunes, but now some of my contact names do not show up on incoming calls.  Help.

    I am assuming that you have associated a picture with the contact in the information for the contact

  • My iphone 4s will not ring for incoming calls...I've checked Do not Disturb, changed my ringtone to default and did a soft reset.  It will vibrate but not ring.  What can I do?

    My iphone will not ring when calls come in.  I have it set to ring and vibrate.  The Do not disturb is turned off and I have reset it but still it will not ring. What can I do?

    Check and see that the silent mode switch on the upper left side is toward the front of the iPhone and there is no orange or red showing.

  • HT4623 I updated my phone to iOS6 and now it will not ring for incoming calls.  It blocks my landline number.  I've tried resetting, updating, etc.  I've gone to the Verizon store.  They were puzzled too. Any ideas of what I should try next?

    I accepted the push to update my iphone to iOS6....now it will not ring.  It blocks calls from my landline. Help!   I've tried resetting, etc.

    It has been caused in an OTA glitch.  You need to hook it up to your computer, restore and update off of iTunes.  Good Luck.

  • My iphone 6 ringer will not work evenafter i have reset. is it because of the new updates? any help on how to get the ringer working. when i test the ringer tunes it works, just that it will not work foran incoming call.

    Iphone 6. 64 gb. Versión is 8.0(12A366). Ringer does not work. Basically not getting any sound for incoming calls. Also no sound for any notifications or alerts. Have tried to reset the phone but still no sound for ringer or notifications.

    Check the mute switch on the side of the device.

  • IPad three will not reconize my apple ID for face time

    Every time I try to log on FaceTime with my apple ID it will not verify it! But when I buy stuff off of iTunes it works just fine! What should I do? I have even made new user Id to see if that would work but it won't !!!!! Help!!!!!

    Every time I try to log on FaceTime with my apple ID it will not verify it! But when I buy stuff off of iTunes it works just fine! What should I do? I have even made new user Id to see if that would work but it won't !!!!! Help!!!!!

  • My iPad doesn't ring when someone calls on face time. Any idea why?

    I have two iPads... both are brand new. When I use face time to call from iPad "1" to iPad "2" everything works fine. When I call from iPad "2" to iPad "1" iPad "1" doesn't ring. The screen lights up with the 'accept call' or reject call buttons, and if I hit accept, it works fine. But it doesn't ring.
    Both iPads have the exact same settings. I have turned face time off, powered down, restarted and turned face time back on... nothing. And no offense to Apple's website, but I can't find anything that helps.
    Any ideas out there? Or will I end up having to restore the original settings and re-install all of the apps and data?
    Thanks...

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
    http://tinyurl.com/32drz3d
     Cheers, Tom

  • Face time does not accept my Apple ID and will not work.  Help!!, face time does not accept my Apple ID and will not work.  Help!!

    Hi, Face time does not accept my Apple ID and therefore Face time does not work. Any suggestions?

    You might have some sort of interference or communication problem, I just wanted to check you were entering the right ID to begin with.
    If you are using the correct ID (without spaces), then you might try restarting the router or trying another wifi channel to eliminate interference.

Maybe you are looking for

  • Installing ColdFusion 11 in Windows 8.1

    I can't no longer download the 30 days trial for CF 10, all I can see is CF 11 when I go to http://www.adobe.com/go/trycoldfusion/ It is OK for me to try CF 11, it is not a problem because I have not submitted a purchase request to my department. I h

  • How to create a PDF Book for mobile devise

    Hi looking at creating a PDF book for mobile device, the book will be a reflection of some of the content of our website http://www.khaolakexplorer.com/ , is there a way to create it automatically??

  • Osx yosemite yüklü imac çok yavaş açılıyor neden

    osx yosemite yüklü imac bilgisayarım  çok yavaş açılıyor ve açılırken bu güne kadar hiç çıkmayan "loading bar" çıkıyor. Neden? Windows kullanır gibi hisssettim, çok utandım

  • Unable to connect to database when running from JDeveloper

    Hi all, When I open a report in Reports Builder , and enter the database connection parameters, everything works fine. When I run my web application from JDeveloper (9.0.5.1), and I tried to run a report, I get this error: Rep-501 : Unable to connect

  • Photoshop, multi-monitor setup has wobbly lines at left of monitors

    Hi All I'm having a problem with jagged, wobbly lines in Photoshop CS5.1.  This has nothing to do with Smoothing or anything (the wobble is more pronounched with smoothing off however). I believe it has something to do with my 3 monitor setup in Wind