My iPad2 went blank. Troubleshooter says driver software MTP USB problem, what do I need to do?

iOS: Resolving update and restore alert messages
For error -50: See error 13 and 14:
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.

Similar Messages

The calendar on my iPhone 4s suddenly went blank and says NoEvents anywhere. What happened and how do I get the information back?

The calendar on my iPhone 42 suddenly went blank and says No Events. How do I get my data back?

I've been having the same problem every 3-4 months: the calendar app seems to hang up, I either reset the app/phone or wait it out, then presto! all internal calendar entries have been deleted. Unlike others in this thread and elsewhere, I am not using iCloud.
Interesting fact: while following the suggestion to hide all calendars, then show all calendars, I noticed that the internal calendar option is MISSING. It's like it just doesn't identify that there ever WAS an internal calendar. Really? Argh.
Apple Support: are you guys monitoring this? I've seen a few similar postings, so I don't think we're alone...
Granted, I have more than a few entries - years of calendar/appointment history have been imported from my old Palm Treo. Thanks to slow performance and odd calendar app crashes, I am very well aware that the iPhone's calendar isn't nearly up to the task of handling this many entries, and have been working to get the quantity of entries down. I must be up near some threshold, as response time seems to have improved with several deleted entries, though it was just before the crash+data loss.
Fortunately, I try to sync with my Outlook calendar nightly, so I do have a backup. However, this type of data loss and instability re VERY painful for those that actually USE and practically LIVE by their calendars. Here's hoping I can remember today's entry modifications...
One additional complaint: WHY can't I edit a recurring appointment WITHOUT it creating a NEW one? Crazy... For all the things this smartphone does well, it does several things VERY stupidly.
_Dave_

My itunes will not open no matter how many times i try! It says its due to a problem. what do i do?

My itunes will not open no matter how many times i try! It says its due to a problem. what do i do?

When you gte requests to locate iTunes.msi like this, the Microsoft Installer Cleanup utility usually fixes it.
Here is a method for removal, clean up and reinstall of iTunes.
== uninstall with cleanup ==
Download a fresh copy of iTunes and the stand alone version of Quicktime (the one without iTunes)
http://www.apple.com/quicktime/download/win.html
http://www.apple.com/itunes/download/
Save the files on your PC.
Download and install Microsoft Installer cleanup utility, there are instructions on the page as well as the download. Note that what you download is the installer not the program – you have to run it to install the program. The installer doesn't give any message to confirm the installation.
http://support.microsoft.com/kb/290301/
(To run the program – All Programs>>Windows Install)
Now use the following method to remove iTunes and its components:
XP
http://support.apple.com/kb/HT1925
Vista
http://support.apple.com/kb/HT1923
*If you hit a problem with one of the uninstalls don't worry*, carry on with the deleting of files and folders as directed in the method.
When you get to deleting Quicktime files in the system32 folder as advised in the method, you can delete any file or folder with Quicktime in the name.
Restart your PC.
Run the Microsoft Installer Cleanup Utility. (Start > All Programs > Windows Install Clean Up)
Remove any references you find to the programs you removed - strictly speaking you only need to worry about those programs where the uninstall failed.
If you don’t see an entry for one of the programs that did not uninstall, look out for blank entries or numeric entries that look like version numbers e.g. 7.x for Quicktime or 1.x for Bonjour.
restart your PC
Install the stand alone Quicktime and check that it works.
If it does, install iTunes.
===

My ipad mini is stil in warranty, but my software has some problem, if format it need to pay?

my ipad mini is stil in warranty, but my software has some problem, if format it need to pay?

Restoring the iPad can be done by the owner and doesn't involve or affect the device's warranty. It's free.
(107649)

I still am having problems with Aperture not loading, It just refuses to work, and I get the message saying it has encountered a problem, and I may need to re-install which I have done dozens of times. The fix mentioned on an earlier post wont work as it

I still am having problems with Aperture not loading, It just refuses to work, and I get the message saying it has encountered a problem, and I may need to re-install which I have done dozens of times. The fix mentioned on an earlier post doesn't work as it is for Ver 10.6.6 and I am running 10.6.7

Do you have Final Cut installed on your machine?
If so, you may want to look at this article: http://support.apple.com/kb/TS3528
Let us know if that helps.

I am looking for R3765C driver software for USB -GPIB? Thanks!

Now we bought NI GPIB-USB-HS connector, but we cannot get the driver software(R3765C Advantest) from the opened NI driver software.
If anyone can give some informations about it, it will help me very much! thanks!

Hi, my name is Yusuke Minami, Applications Engineering, National Instruments Japan.
You can download the instrument driver for R3765C Advantest at:
http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=2588
I hope this will work well.
日本ナショナルインスツルメンツ株式会社　技術部　巳波裕介
Yusuke Minami, Applications Engineering, National Instruments Japan
技術サポートウェブページ:　http://www.ni.com/support/ja
お問い合わせフリーダイヤル:　0120-527196

HT4623 i tried to update my phone to new software and there is no button that says software update so now what do i need to do?

I have tried to update my iphone 3g with new software and i cant do it. i need help. i cant find the software and i cant do it thru my itunes or my phone

You update the iOS using iTunes
If you have an iPhone 3G you can only update to 4.2.1
if you have an iPhone 3GS you can update to 6.1.3
http://support.apple.com/kb/HT4623

Want to replace my hard drive from 160g to 500g what do i need to know

want to replace my hard drive on a compaq presario sr055cl. it has a 160 g hard drive how big can i go
This question was solved.
View Solution.

Here is the Service Manual showing how to replace a hard drive:
Manual
It does have 2 SATA connectors. Here is a picture of the motherboard.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00069442&tmp_task=prodinfoCategory&cc=us&dlc=en...
This is primitive SATA. It is a SATA connection to an IDE bus. However, the fact that you have a 160 gig drive already installed tells me the motherboard will accept Large Block Addressing 48 bit (LBA48) which means you are not really constrained by size. I am sure a 500 gig drive will work and will bet a 1 TB would also work. I will also bet you would have problems with a high density drive of 2 TB or higher. The existing drive is a IDE, which means it is connected to the motherboard with a flat ribbon cable. You will have a hard time finding an IDE drive on the market these days. It will have to be SATA. Just attach a SATA data cable between the hard drive and the motherboard. You will likely need to get a molex (white 4-pin) to SATA power adapter, too, but those often come with the hard drive or are available for a couple bucks at the store where hard drives are sold.
You should be able to clone the old drive to the new using cloning software. I like and recommend Acronis True Image Home. If I were doing this I would connect the new SATA drive to the motherboard port with the side cover off and also bring power to the SATA drive. I would leave the original drive in and boot from the cloning software disk doing a proportional resize so all partitions are expanded the same percentage. After the clone is complete remove the original drive and bolt the SATA drive in its place. I would just tell you to add a second hard drive but the computer only has space for one unless you want to remove the card reader.
You may need to enable the SATA ports in the BIOS if they are not currently in use. The motherboard picture page linked above tells how to enter the BIOS. Post back if you need more help.
If this is "the Answer" please click "Accept as Solution" to help others find it.

I have a new iMac at home and a PC at work. My work PC has VPN software on it. What do I need to do in order use the VPN on the iMac to access the PC at work?

I have a new iMac at home and use a PC at work. My work PC has VPN/Remote Desktop software on it. I would like to be able to access my PC from home on my iMac using this VPN. I am not sure how to make that happen.

Office 2011 is not compatbile with Exchange 2003.
I suggest you post further Office related questions on Microsoft's own forums for their Mac software:
http://answers.microsoft.com/en-us/mac

When I open the download manager it says not supported by this architecture, what do I need to insta

When I open the download manager it says cannot be supported by this architecture. Do I need to install something?

Do I need to install something?
No. You need to get a new Mac.
Mylenium

HT1152 Can I copy a video disk to a hard drive useing superdrive if so what app is needed.

I am trying to use my Superdrive with my MacBook Air to copy a DVD movie to an external hard drive ???
Can someone direct me to an appropriate app or method to achiev this.

Andynorthstar wrote:
I am trying to use my Superdrive with my MacBook Air to copy a DVD movie to an external hard drive ???
Many -- perhaps most -- commercial movie DVDs are protected against copying. Breaking this copy protection scheme is illegal in the USA, where Apple, which hosts this forum, is based. Advice on how to perform illegal acts is also illegal, so, if Apple allowed such advice on its forum, it would make itself liable to prosecution. That's one of the reasons neither Apple, nor any other major corporation (Microsoft, Sony, etc) will allow such advice on the fora they host.
When you buy a DVD, you don't actually buy the movie. You buy a licence to see the movie under certain conditions. If the licence allows you to make copies (some do), and the DVD is not copy protected -- then nothing is simpler. You just copy the VIDEO_TS folder to any location on the external drive you choose, then you view the movie with DVD Player. File > Open DVD Media…, navigate to the VIDEO_TS folder, select it, click the Choose button, then press the spacebar to start watching.

Downloaded jing and I have OSX 10.5.8 but I cannot open it up, says not supported by architecture. What to I need to correct please?

I downloaded jing onto my computer. I have OSX 10.5.8, which is what jing requires so it shouldn't be an issue. When I go into the applications file and click on the jing icon, it won't open and says "it is not supported ny architecture". What does this mean and how can I fix it? Thank you!

The current version of Jing requires an Intel processor running OS X 10.5.8 or later. The message you're receiving is because the iBook uses the PowerPC platform and not Intel. The last release of Jing that will run on your system is version 2.3, which they no longer support and it doesn't auto update.

MY SCREEN WENT BLANK DURING THE DOWNLOAD OF APPLE's UPDATE

I was downloading a system update for my MacBook and my screen went blank.
Applecare was unable to identify problem.
I took it into service and they said this has been happening lately with system downloads.
Am I doomed? I've only had this computer for 4 months.
Ray

Not a solution to your problem, but anyway: do you see anything on the screen when putting it into bright light? If so, then the backlight is of while the display is actual working.
My screen sometimes blacks out shortly after waking up from sleep. It always comes back within a minute. Annoying, and I don't have a solution yet and hope it does not need repair. However, during those blackouts I actually can tell what's on the screen when using a torchlight...
I assume you tried fn-F2 to ensure brightness is not set to off? And fn-F7 to ensure the MacBook doesn't think it's using some external screen? Did you try to reset the SMC? The System Management Controller is responsible for power management of the computer and also controls backlighting.
http://docs.info.apple.com/article.html?artnum=303319
Please keep us updated about any results.
Arjan.
MacBook 2GHz 2GB Mac OS X (10.4.8)

Problem Syncing Outlook....says outlook sync client encountered problem

I have been syncing outlook calendar and contacts from my PC to my iPhone with no problems. I have version 1.1.2 on my iPhone and 7.5 or whatever the latest is on iTunes software. The syncs were fine until recently and now I cant sync and get an error message that says "outlook sync client encountered problem" What could possibly have happened....I read some posts that say to go back to iTunes 7.3 etc....this has to be a common problem....any suggestions.

Here is an article from the apple support website that might help out.
http://docs.info.apple.com/article.html?artnum=305845

HT4528 What to i need to do when my phone says not enouf icloud storage

What do i need to do if my phone says not enouf i cloud storage what do i need to do?

you can either:
1. purchase additional icloud storage to keep backing up with iCloud, check out: http://support.apple.com/kb/ht4847
or
2. Turn off the iCloud backup and choose to backup with iTunes from now on. To turn off iCloud backup, go to Settings - iCloud - Storage and Backup - turn off 'iCloud backup' and use this article for backing up with iTunes: http://support.apple.com/kb/ht1766
Hope this helps

My iPad2 went blank. Troubleshooter says driver software MTP USB problem, what do I need to do?

Similar Messages

Maybe you are looking for